Merge master.kernel.org:/home/rmk/linux-2.6-arm

arch/arm/configs/corgi_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.14-rc3
-# Sun Oct  9 15:46:42 2005
+# Linux kernel version: 2.6.15-rc2
+# Mon Nov 28 10:30:09 2005
 #
 CONFIG_ARM=y
 CONFIG_MMU=y
@@ -63,6 +63,23 @@ CONFIG_OBSOLETE_MODPARM=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_KMOD=y
 
+#
+# Block layer
+#
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
 #
 # System Type
 #
@@ -85,6 +102,7 @@ CONFIG_ARCH_PXA=y
 # CONFIG_ARCH_LH7A40X is not set
 # CONFIG_ARCH_OMAP is not set
 # CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_REALVIEW is not set
 # CONFIG_ARCH_IMX is not set
 # CONFIG_ARCH_H720X is not set
 # CONFIG_ARCH_AAEC2000 is not set
@@ -98,12 +116,14 @@ CONFIG_ARCH_PXA=y
 CONFIG_PXA_SHARPSL=y
 CONFIG_PXA_SHARPSL_25x=y
 # CONFIG_PXA_SHARPSL_27x is not set
-# CONFIG_MACH_POODLE is not set
+CONFIG_MACH_POODLE=y
 CONFIG_MACH_CORGI=y
 CONFIG_MACH_SHEPHERD=y
 CONFIG_MACH_HUSKY=y
+CONFIG_MACH_TOSA=y
 CONFIG_PXA25x=y
 CONFIG_PXA_SHARP_C7xx=y
+CONFIG_PXA_SSP=y
 
 #
 # Processor Type
@@ -155,6 +175,7 @@ CONFIG_FLATMEM_MANUAL=y
 CONFIG_FLATMEM=y
 CONFIG_FLAT_NODE_MEM_MAP=y
 # CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4096
 CONFIG_ALIGNMENT_TRAP=y
 
 #
@@ -235,6 +256,10 @@ CONFIG_INET6_TUNNEL=m
 CONFIG_IPV6_TUNNEL=m
 CONFIG_NETFILTER=y
 # CONFIG_NETFILTER_DEBUG is not set
+
+#
+# Core Netfilter Configuration
+#
 # CONFIG_NETFILTER_NETLINK is not set
 
 #
@@ -356,6 +381,10 @@ CONFIG_IP6_NF_RAW=m
 # CONFIG_NET_DIVERT is not set
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
 # CONFIG_NET_SCHED is not set
 CONFIG_NET_CLS_ROUTE=y
 
@@ -413,6 +442,7 @@ CONFIG_IRCOMM=m
 # CONFIG_SMC_IRCC_FIR is not set
 # CONFIG_ALI_FIR is not set
 # CONFIG_VIA_FIR is not set
+CONFIG_PXA_FICP=m
 CONFIG_BT=m
 CONFIG_BT_L2CAP=m
 CONFIG_BT_SCO=m
@@ -431,7 +461,6 @@ CONFIG_BT_HCIUSB=m
 CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_H4=y
 CONFIG_BT_HCIUART_BCSP=y
-CONFIG_BT_HCIUART_BCSP_TXCRC=y
 CONFIG_BT_HCIBCM203X=m
 CONFIG_BT_HCIBPA10X=m
 CONFIG_BT_HCIBFUSB=m
@@ -458,6 +487,11 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 CONFIG_FW_LOADER=y
 # CONFIG_DEBUG_DRIVER is not set
 
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
 #
 # Memory Technology Devices (MTD)
 #
@@ -477,6 +511,7 @@ CONFIG_MTD_BLOCK=y
 # CONFIG_FTL is not set
 # CONFIG_NFTL is not set
 # CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
 
 #
 # RAM/ROM/Flash chip drivers
@@ -531,6 +566,11 @@ CONFIG_MTD_NAND_IDS=y
 CONFIG_MTD_NAND_SHARPSL=y
 # CONFIG_MTD_NAND_NANDSIM is not set
 
+#
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
 #
 # Parallel port support
 #
@@ -551,14 +591,6 @@ CONFIG_BLK_DEV_LOOP=y
 # CONFIG_BLK_DEV_RAM is not set
 CONFIG_BLK_DEV_RAM_COUNT=16
 # CONFIG_CDROM_PKTCDVD is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
 # CONFIG_ATA_OVER_ETH is not set
 
 #
@@ -625,6 +657,7 @@ CONFIG_SCSI_MULTI_LUN=y
 #
 # SCSI low-level drivers
 #
+# CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_SATA is not set
 # CONFIG_SCSI_DEBUG is not set
 
@@ -748,6 +781,7 @@ CONFIG_PPP_ASYNC=m
 # CONFIG_PPP_SYNC_TTY is not set
 # CONFIG_PPP_DEFLATE is not set
 CONFIG_PPP_BSDCOMP=m
+# CONFIG_PPP_MPPE is not set
 # CONFIG_PPPOE is not set
 # CONFIG_SLIP is not set
 # CONFIG_SHAPER is not set
@@ -850,11 +884,15 @@ CONFIG_UNIX98_PTYS=y
 # PCMCIA character devices
 #
 # CONFIG_SYNCLINK_CS is not set
+# CONFIG_CARDMAN_4000 is not set
+# CONFIG_CARDMAN_4040 is not set
 # CONFIG_RAW_DRIVER is not set
 
 #
 # TPM devices
 #
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
 
 #
 # I2C support
@@ -889,6 +927,7 @@ CONFIG_I2C_PXA=y
 # CONFIG_SENSORS_PCF8591 is not set
 # CONFIG_SENSORS_RTC8564 is not set
 # CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_RTC_X1205_I2C is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
@@ -957,7 +996,10 @@ CONFIG_VIDEO_DEV=m
 # CONFIG_VIDEO_SAA5246A is not set
 # CONFIG_VIDEO_SAA5249 is not set
 # CONFIG_TUNER_3036 is not set
+# CONFIG_VIDEO_EM28XX is not set
 # CONFIG_VIDEO_OVCAMCHIP is not set
+# CONFIG_VIDEO_AUDIO_DECODER is not set
+# CONFIG_VIDEO_DECODER is not set
 
 #
 # Radio Adapters
@@ -976,13 +1018,12 @@ CONFIG_FB=y
 CONFIG_FB_CFB_FILLRECT=y
 CONFIG_FB_CFB_COPYAREA=y
 CONFIG_FB_CFB_IMAGEBLIT=y
-CONFIG_FB_SOFT_CURSOR=y
 # CONFIG_FB_MACMODES is not set
 # CONFIG_FB_MODE_HELPERS is not set
 # CONFIG_FB_TILEBLITTING is not set
+# CONFIG_FB_S1D13XXX is not set
 # CONFIG_FB_PXA is not set
 CONFIG_FB_W100=y
-# CONFIG_FB_S1D13XXX is not set
 # CONFIG_FB_VIRTUAL is not set
 
 #
@@ -991,6 +1032,7 @@ CONFIG_FB_W100=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_DUMMY_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
 CONFIG_FONTS=y
 CONFIG_FONT_8x8=y
 CONFIG_FONT_8x16=y
@@ -1087,15 +1129,15 @@ CONFIG_USB_SL811_CS=m
 # USB Device Class drivers
 #
 # CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
+CONFIG_USB_ACM=m
+CONFIG_USB_PRINTER=m
 
 #
-# USB Bluetooth TTY can only be used with disabled Bluetooth subsystem
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
 #
-CONFIG_USB_ACM=m
-CONFIG_USB_PRINTER=m
 
 #
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
+# may also be needed; see USB_STORAGE Help for more information
 #
 CONFIG_USB_STORAGE=m
 # CONFIG_USB_STORAGE_DEBUG is not set
@@ -1107,7 +1149,6 @@ CONFIG_USB_STORAGE=m
 # CONFIG_USB_STORAGE_SDDR09 is not set
 # CONFIG_USB_STORAGE_SDDR55 is not set
 # CONFIG_USB_STORAGE_JUMPSHOT is not set
-# CONFIG_USB_STORAGE_ONETOUCH is not set
 
 #
 # USB Input Devices
@@ -1185,6 +1226,7 @@ CONFIG_USB_MON=y
 CONFIG_USB_SERIAL=m
 CONFIG_USB_SERIAL_GENERIC=y
 # CONFIG_USB_SERIAL_AIRPRIME is not set
+# CONFIG_USB_SERIAL_ANYDATA is not set
 CONFIG_USB_SERIAL_BELKIN=m
 # CONFIG_USB_SERIAL_WHITEHEAT is not set
 CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
@@ -1340,6 +1382,7 @@ CONFIG_RAMFS=y
 CONFIG_JFFS2_FS=y
 CONFIG_JFFS2_FS_DEBUG=0
 CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_SUMMARY=y
 CONFIG_JFFS2_COMPRESSION_OPTIONS=y
 CONFIG_JFFS2_ZLIB=y
 CONFIG_JFFS2_RTIME=y
@@ -1466,7 +1509,9 @@ CONFIG_DETECT_SOFTLOCKUP=y
 CONFIG_DEBUG_BUGVERBOSE=y
 # CONFIG_DEBUG_INFO is not set
 # CONFIG_DEBUG_FS is not set
+# CONFIG_DEBUG_VM is not set
 CONFIG_FRAME_POINTER=y
+# CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_DEBUG_USER is not set
 # CONFIG_DEBUG_WAITQ is not set
 CONFIG_DEBUG_ERRORS=y

arch/arm/configs/spitz_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.14-rc3
-# Sun Oct  9 17:11:19 2005
+# Linux kernel version: 2.6.15-rc2
+# Mon Nov 28 10:26:52 2005
 #
 CONFIG_ARM=y
 CONFIG_MMU=y
@@ -63,6 +63,23 @@ CONFIG_OBSOLETE_MODPARM=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_KMOD=y
 
+#
+# Block layer
+#
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
 #
 # System Type
 #
@@ -85,6 +102,7 @@ CONFIG_ARCH_PXA=y
 # CONFIG_ARCH_LH7A40X is not set
 # CONFIG_ARCH_OMAP is not set
 # CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_REALVIEW is not set
 # CONFIG_ARCH_IMX is not set
 # CONFIG_ARCH_H720X is not set
 # CONFIG_ARCH_AAEC2000 is not set
@@ -98,10 +116,13 @@ CONFIG_ARCH_PXA=y
 CONFIG_PXA_SHARPSL=y
 # CONFIG_PXA_SHARPSL_25x is not set
 CONFIG_PXA_SHARPSL_27x=y
+CONFIG_MACH_AKITA=y
 CONFIG_MACH_SPITZ=y
 CONFIG_MACH_BORZOI=y
 CONFIG_PXA27x=y
+CONFIG_IWMMXT=y
 CONFIG_PXA_SHARP_Cxx00=y
+CONFIG_PXA_SSP=y
 
 #
 # Processor Type
@@ -153,6 +174,7 @@ CONFIG_FLATMEM_MANUAL=y
 CONFIG_FLATMEM=y
 CONFIG_FLAT_NODE_MEM_MAP=y
 # CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4096
 CONFIG_ALIGNMENT_TRAP=y
 
 #
@@ -233,6 +255,10 @@ CONFIG_INET6_TUNNEL=m
 CONFIG_IPV6_TUNNEL=m
 CONFIG_NETFILTER=y
 # CONFIG_NETFILTER_DEBUG is not set
+
+#
+# Core Netfilter Configuration
+#
 # CONFIG_NETFILTER_NETLINK is not set
 
 #
@@ -354,6 +380,10 @@ CONFIG_IP6_NF_RAW=m
 # CONFIG_NET_DIVERT is not set
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
 # CONFIG_NET_SCHED is not set
 CONFIG_NET_CLS_ROUTE=y
 
@@ -411,6 +441,7 @@ CONFIG_IRCOMM=m
 # CONFIG_SMC_IRCC_FIR is not set
 # CONFIG_ALI_FIR is not set
 # CONFIG_VIA_FIR is not set
+CONFIG_PXA_FICP=m
 CONFIG_BT=m
 CONFIG_BT_L2CAP=m
 CONFIG_BT_SCO=m
@@ -429,7 +460,6 @@ CONFIG_BT_HCIUSB=m
 CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_H4=y
 CONFIG_BT_HCIUART_BCSP=y
-CONFIG_BT_HCIUART_BCSP_TXCRC=y
 CONFIG_BT_HCIBCM203X=m
 CONFIG_BT_HCIBPA10X=m
 CONFIG_BT_HCIBFUSB=m
@@ -456,6 +486,11 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 CONFIG_FW_LOADER=y
 # CONFIG_DEBUG_DRIVER is not set
 
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
 #
 # Memory Technology Devices (MTD)
 #
@@ -475,6 +510,7 @@ CONFIG_MTD_BLOCK=y
 # CONFIG_FTL is not set
 # CONFIG_NFTL is not set
 # CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
 
 #
 # RAM/ROM/Flash chip drivers
@@ -529,6 +565,11 @@ CONFIG_MTD_NAND_IDS=y
 CONFIG_MTD_NAND_SHARPSL=y
 # CONFIG_MTD_NAND_NANDSIM is not set
 
+#
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
 #
 # Parallel port support
 #
@@ -549,14 +590,6 @@ CONFIG_BLK_DEV_LOOP=y
 # CONFIG_BLK_DEV_RAM is not set
 CONFIG_BLK_DEV_RAM_COUNT=16
 # CONFIG_CDROM_PKTCDVD is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
 # CONFIG_ATA_OVER_ETH is not set
 
 #
@@ -623,6 +656,7 @@ CONFIG_SCSI_MULTI_LUN=y
 #
 # SCSI low-level drivers
 #
+# CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_SATA is not set
 # CONFIG_SCSI_DEBUG is not set
 
@@ -746,6 +780,7 @@ CONFIG_PPP_ASYNC=m
 # CONFIG_PPP_SYNC_TTY is not set
 # CONFIG_PPP_DEFLATE is not set
 CONFIG_PPP_BSDCOMP=m
+# CONFIG_PPP_MPPE is not set
 # CONFIG_PPPOE is not set
 # CONFIG_SLIP is not set
 # CONFIG_SHAPER is not set
@@ -771,6 +806,7 @@ CONFIG_INPUT=y
 # CONFIG_INPUT_TSDEV is not set
 CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_EVBUG is not set
+# CONFIG_INPUT_POWER is not set
 
 #
 # Input Device Drivers
@@ -848,11 +884,15 @@ CONFIG_UNIX98_PTYS=y
 # PCMCIA character devices
 #
 # CONFIG_SYNCLINK_CS is not set
+# CONFIG_CARDMAN_4000 is not set
+# CONFIG_CARDMAN_4040 is not set
 # CONFIG_RAW_DRIVER is not set
 
 #
 # TPM devices
 #
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
 
 #
 # I2C support
@@ -891,14 +931,13 @@ CONFIG_FB=y
 CONFIG_FB_CFB_FILLRECT=y
 CONFIG_FB_CFB_COPYAREA=y
 CONFIG_FB_CFB_IMAGEBLIT=y
-CONFIG_FB_SOFT_CURSOR=y
 # CONFIG_FB_MACMODES is not set
 # CONFIG_FB_MODE_HELPERS is not set
 # CONFIG_FB_TILEBLITTING is not set
+# CONFIG_FB_S1D13XXX is not set
 CONFIG_FB_PXA=y
-# CONFIG_FB_W100 is not set
 # CONFIG_FB_PXA_PARAMETERS is not set
-# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_W100 is not set
 # CONFIG_FB_VIRTUAL is not set
 
 #
@@ -907,6 +946,7 @@ CONFIG_FB_PXA=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_DUMMY_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
 CONFIG_FONTS=y
 CONFIG_FONT_8x8=y
 CONFIG_FONT_8x16=y
@@ -965,15 +1005,15 @@ CONFIG_USB_SL811_CS=m
 #
 # USB Device Class drivers
 #
+CONFIG_USB_ACM=m
+CONFIG_USB_PRINTER=m
 
 #
-# USB Bluetooth TTY can only be used with disabled Bluetooth subsystem
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
 #
-CONFIG_USB_ACM=m
-CONFIG_USB_PRINTER=m
 
 #
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
+# may also be needed; see USB_STORAGE Help for more information
 #
 CONFIG_USB_STORAGE=m
 # CONFIG_USB_STORAGE_DEBUG is not set
@@ -985,7 +1025,6 @@ CONFIG_USB_STORAGE=m
 # CONFIG_USB_STORAGE_SDDR09 is not set
 # CONFIG_USB_STORAGE_SDDR55 is not set
 # CONFIG_USB_STORAGE_JUMPSHOT is not set
-# CONFIG_USB_STORAGE_ONETOUCH is not set
 
 #
 # USB Input Devices
@@ -1058,6 +1097,7 @@ CONFIG_USB_MON=y
 CONFIG_USB_SERIAL=m
 CONFIG_USB_SERIAL_GENERIC=y
 # CONFIG_USB_SERIAL_AIRPRIME is not set
+# CONFIG_USB_SERIAL_ANYDATA is not set
 CONFIG_USB_SERIAL_BELKIN=m
 # CONFIG_USB_SERIAL_WHITEHEAT is not set
 CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
@@ -1218,6 +1258,7 @@ CONFIG_RAMFS=y
 CONFIG_JFFS2_FS=y
 CONFIG_JFFS2_FS_DEBUG=0
 CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_SUMMARY=y
 CONFIG_JFFS2_COMPRESSION_OPTIONS=y
 CONFIG_JFFS2_ZLIB=y
 CONFIG_JFFS2_RTIME=y
@@ -1344,7 +1385,9 @@ CONFIG_DETECT_SOFTLOCKUP=y
 CONFIG_DEBUG_BUGVERBOSE=y
 # CONFIG_DEBUG_INFO is not set
 # CONFIG_DEBUG_FS is not set
+# CONFIG_DEBUG_VM is not set
 CONFIG_FRAME_POINTER=y
+# CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_DEBUG_USER is not set
 # CONFIG_DEBUG_WAITQ is not set
 CONFIG_DEBUG_ERRORS=y

arch/arm/kernel/head.S

@@ -17,7 +17,6 @@
 
 #include <asm/assembler.h>
 #include <asm/domain.h>
-#include <asm/mach-types.h>
 #include <asm/procinfo.h>
 #include <asm/ptrace.h>
 #include <asm/asm-offsets.h>
@@ -83,7 +82,7 @@ ENTRY(stext)
 						@ and irqs disabled
 	bl	__lookup_processor_type		@ r5=procinfo r9=cpuid
 	movs	r10, r5				@ invalid processor (r5=0)?
-	beq	__error_p				@ yes, error 'p'
+	beq	__error_p			@ yes, error 'p'
 	bl	__lookup_machine_type		@ r5=machinfo
 	movs	r8, r5				@ invalid machine (r5=0)?
 	beq	__error_a			@ yes, error 'a'
@@ -343,16 +342,12 @@ __create_page_tables:
 	bne	1b
 #if defined(CONFIG_ARCH_NETWINDER) || defined(CONFIG_ARCH_CATS)
 	/*
-	 * If we're using the NetWinder, we need to map in
-	 * the 16550-type serial port for the debug messages
+	 * If we're using the NetWinder or CATS, we also need to map
+	 * in the 16550-type serial port for the debug messages
 	 */
-	teq	r1, #MACH_TYPE_NETWINDER
-	teqne	r1, #MACH_TYPE_CATS
-	bne	1f
 	add	r0, r4, #0xff000000 >> 18
 	orr	r3, r7, #0x7c000000
 	str	r3, [r0]
-1:
 #endif
 #ifdef CONFIG_ARCH_RPC
 	/*

arch/arm/mach-pxa/Kconfig

@@ -44,6 +44,7 @@ config PXA_SHARPSL_25x
 config PXA_SHARPSL_27x
 	bool "Sharp PXA270 models (SL-Cxx00)"
 	select PXA27x
+	select IWMMXT
 
 endchoice
 
@@ -60,7 +61,6 @@ config MACH_CORGI
 	bool "Enable Sharp SL-C700 (Corgi) Support"
 	depends PXA_SHARPSL_25x
 	select PXA_SHARP_C7xx
-	select PXA_SSP
 
 config MACH_SHEPHERD
 	bool "Enable Sharp SL-C750 (Shepherd) Support"
@@ -90,7 +90,7 @@ config MACH_BORZOI
 
 config MACH_TOSA
 	bool "Enable Sharp SL-6000x (Tosa) Support"
-	depends PXA_SHARPSL
+	depends PXA_SHARPSL_25x
 
 config PXA25x
 	bool

arch/arm/mach-realview/core.c

@@ -30,7 +30,6 @@
 #include <asm/io.h>
 #include <asm/irq.h>
 #include <asm/leds.h>
-#include <asm/mach-types.h>
 #include <asm/hardware/amba.h>
 #include <asm/hardware/amba_clcd.h>
 #include <asm/hardware/arm_timer.h>

arch/arm/mm/consistent.c

@@ -66,6 +66,7 @@ struct vm_region {
 	unsigned long		vm_start;
 	unsigned long		vm_end;
 	struct page		*vm_pages;
+	int			vm_active;
 };
 
 static struct vm_region consistent_head = {
@@ -104,6 +105,7 @@ vm_region_alloc(struct vm_region *head, size_t size, gfp_t gfp)
 	list_add_tail(&new->vm_list, &c->vm_list);
 	new->vm_start = addr;
 	new->vm_end = addr + size;
+	new->vm_active = 1;
 
 	spin_unlock_irqrestore(&consistent_lock, flags);
 	return new;
@@ -120,7 +122,7 @@ static struct vm_region *vm_region_find(struct vm_region *head, unsigned long ad
 	struct vm_region *c;
 	
 	list_for_each_entry(c, &head->vm_list, vm_list) {
-		if (c->vm_start == addr)
+		if (c->vm_active && c->vm_start == addr)
 			goto out;
 	}
 	c = NULL;
@@ -319,6 +321,7 @@ EXPORT_SYMBOL(dma_mmap_writecombine);
 
 /*
  * free a page as defined by the above mapping.
+ * Must not be called with IRQs disabled.
  */
 void dma_free_coherent(struct device *dev, size_t size, void *cpu_addr, dma_addr_t handle)
 {
@@ -326,14 +329,18 @@ void dma_free_coherent(struct device *dev, size_t size, void *cpu_addr, dma_addr
 	unsigned long flags, addr;
 	pte_t *ptep;
 
+	WARN_ON(irqs_disabled());
+
 	size = PAGE_ALIGN(size);
 
 	spin_lock_irqsave(&consistent_lock, flags);
-
 	c = vm_region_find(&consistent_head, (unsigned long)cpu_addr);
 	if (!c)
 		goto no_area;
 
+	c->vm_active = 0;
+	spin_unlock_irqrestore(&consistent_lock, flags);
+
 	if ((c->vm_end - c->vm_start) != size) {
 		printk(KERN_ERR "%s: freeing wrong coherent size (%ld != %d)\n",
 		       __func__, c->vm_end - c->vm_start, size);
@@ -372,8 +379,8 @@ void dma_free_coherent(struct device *dev, size_t size, void *cpu_addr, dma_addr
 
 	flush_tlb_kernel_range(c->vm_start, c->vm_end);
 
+	spin_lock_irqsave(&consistent_lock, flags);
 	list_del(&c->vm_list);
-
 	spin_unlock_irqrestore(&consistent_lock, flags);
 
 	kfree(c);

arch/arm/tools/mach-types

@@ -12,7 +12,7 @@
 #
 #   http://www.arm.linux.org.uk/developer/machines/?action=new
 #
-# Last update: Fri Nov 11 21:55:04 2005
+# Last update: Fri Nov 25 14:43:04 2005
 #
 # machine_is_xxx	CONFIG_xxxx		MACH_TYPE_xxx		number
 #
@@ -857,12 +857,12 @@ osiris			MACH_OSIRIS		OSIRIS			842
 maestro			MACH_MAESTRO		MAESTRO			843
 tunge2			MACH_TUNGE2		TUNGE2			844
 ixbbm			MACH_IXBBM		IXBBM			845
-mx27			MACH_MX27		MX27			846
+mx27ads			MACH_MX27		MX27			846
 ax8004			MACH_AX8004		AX8004			847
 at91sam9261ek		MACH_AT91SAM9261EK	AT91SAM9261EK		848
 loft			MACH_LOFT		LOFT			849
 magpie			MACH_MAGPIE		MAGPIE			850
-mx21			MACH_MX21		MX21			851
+mx21ads			MACH_MX21		MX21			851
 mb87m3400		MACH_MB87M3400		MB87M3400		852
 mguard_delta		MACH_MGUARD_DELTA	MGUARD_DELTA		853
 davinci_dvdp		MACH_DAVINCI_DVDP	DAVINCI_DVDP		854
@@ -897,10 +897,16 @@ omi_board		MACH_OMI_BOARD		OMI_BOARD		882
 mx21civ			MACH_MX21CIV		MX21CIV			883
 mahi_cdac		MACH_MAHI_CDAC		MAHI_CDAC		884
 xscale_palmtx		MACH_XSCALE_PALMTX	XSCALE_PALMTX		885
-arch_s3c2413		MACH_ARCH_S3C2413	ARCH_S3C2413		886
 s3c2413			MACH_S3C2413		S3C2413			887
 samsys_ep0		MACH_SAMSYS_EP0		SAMSYS_EP0		888
 wg302v1			MACH_WG302V1		WG302V1			889
 wg302v2			MACH_WG302V2		WG302V2			890
 eb42x			MACH_EB42X		EB42X			891
 iq331es			MACH_IQ331ES		IQ331ES			892
+cosydsp			MACH_COSYDSP		COSYDSP			893
+uplat7d			MACH_UPLAT7D		UPLAT7D			894
+ptdavinci		MACH_PTDAVINCI		PTDAVINCI		895
+mbus			MACH_MBUS		MBUS			896
+nadia2vb		MACH_NADIA2VB		NADIA2VB		897
+r1000			MACH_R1000		R1000			898
+hw90250			MACH_HW90250		HW90250			899

include/asm-arm/arch-sa1100/io.h

@@ -10,8 +10,6 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#include <asm/hardware.h>
-
 #define IO_SPACE_LIMIT 0xffffffff
 
 /*