Input: cyapa - add gen3 trackpad device firmware update support

Add support for firmware image update for gen3 trackpad devices; the
firmware update is initiated by writing to update_fw sysfs attribute.
Signed-off-by: NDudley Du <dudl@cypress.com>
Tested-by: NJeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

drivers/input/mouse/cyapa_gen3.c

@@ -20,6 +20,7 @@
 #include <linux/input/mt.h>
 #include <linux/module.h>
 #include <linux/slab.h>
+#include <linux/unaligned/access_ok.h>
 #include "cyapa.h"
 
 
@@ -115,6 +116,18 @@ struct cyapa_reg_data {
 	struct cyapa_touch touches[5];
 } __packed;
 
+struct gen3_write_block_cmd {
+	u8 checksum_seed;  /* Always be 0xff */
+	u8 cmd_code;       /* command code: 0x39 */
+	u8 key[8];         /* 8-byte security key */
+	__be16 block_num;
+	u8 block_data[CYAPA_FW_BLOCK_SIZE];
+	u8 block_checksum;  /* Calculated using bytes 12 - 75 */
+	u8 cmd_checksum;    /* Calculated using bytes 0-76 */
+} __packed;
+
+static const u8 security_key[] = {
+		0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07 };
 static const u8 bl_activate[] = { 0x00, 0xff, 0x38, 0x00, 0x01, 0x02, 0x03,
 		0x04, 0x05, 0x06, 0x07 };
 static const u8 bl_deactivate[] = { 0x00, 0xff, 0x3b, 0x00, 0x01, 0x02, 0x03,
@@ -423,6 +436,87 @@ static int cyapa_gen3_state_parse(struct cyapa *cyapa, u8 *reg_data, int len)
 	return -EAGAIN;
 }
 
+/*
+ * Enter bootloader by soft resetting the device.
+ *
+ * If device is already in the bootloader, the function just returns.
+ * Otherwise, reset the device; after reset, device enters bootloader idle
+ * state immediately.
+ *
+ * Returns:
+ *   0        on success
+ *   -EAGAIN  device was reset, but is not now in bootloader idle state
+ *   < 0      if the device never responds within the timeout
+ */
+static int cyapa_gen3_bl_enter(struct cyapa *cyapa)
+{
+	int error;
+	int waiting_time;
+
+	error = cyapa_poll_state(cyapa, 500);
+	if (error)
+		return error;
+	if (cyapa->state == CYAPA_STATE_BL_IDLE) {
+		/* Already in BL_IDLE. Skipping reset. */
+		return 0;
+	}
+
+	if (cyapa->state != CYAPA_STATE_OP)
+		return -EAGAIN;
+
+	cyapa->operational = false;
+	cyapa->state = CYAPA_STATE_NO_DEVICE;
+	error = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET, 0x01);
+	if (error)
+		return -EIO;
+
+	usleep_range(25000, 50000);
+	waiting_time = 2000;  /* For some shipset, max waiting time is 1~2s. */
+	do {
+		error = cyapa_poll_state(cyapa, 500);
+		if (error) {
+			if (error == -ETIMEDOUT) {
+				waiting_time -= 500;
+				continue;
+			}
+			return error;
+		}
+
+		if ((cyapa->state == CYAPA_STATE_BL_IDLE) &&
+			!(cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG))
+			break;
+
+		msleep(100);
+		waiting_time -= 100;
+	} while (waiting_time > 0);
+
+	if ((cyapa->state != CYAPA_STATE_BL_IDLE) ||
+		(cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG))
+		return -EAGAIN;
+
+	return 0;
+}
+
+static int cyapa_gen3_bl_activate(struct cyapa *cyapa)
+{
+	int error;
+
+	error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_activate),
+					bl_activate);
+	if (error)
+		return error;
+
+	/* Wait for bootloader to activate; takes between 2 and 12 seconds */
+	msleep(2000);
+	error = cyapa_poll_state(cyapa, 11000);
+	if (error)
+		return error;
+	if (cyapa->state != CYAPA_STATE_BL_ACTIVE)
+		return -EAGAIN;
+
+	return 0;
+}
+
 static int cyapa_gen3_bl_deactivate(struct cyapa *cyapa)
 {
 	int error;
@@ -483,6 +577,212 @@ static int cyapa_gen3_bl_exit(struct cyapa *cyapa)
 	return 0;
 }
 
+static u16 cyapa_gen3_csum(const u8 *buf, size_t count)
+{
+	int i;
+	u16 csum = 0;
+
+	for (i = 0; i < count; i++)
+		csum += buf[i];
+
+	return csum;
+}
+
+/*
+ * Verify the integrity of a CYAPA firmware image file.
+ *
+ * The firmware image file is 30848 bytes, composed of 482 64-byte blocks.
+ *
+ * The first 2 blocks are the firmware header.
+ * The next 480 blocks are the firmware image.
+ *
+ * The first two bytes of the header hold the header checksum, computed by
+ * summing the other 126 bytes of the header.
+ * The last two bytes of the header hold the firmware image checksum, computed
+ * by summing the 30720 bytes of the image modulo 0xffff.
+ *
+ * Both checksums are stored little-endian.
+ */
+static int cyapa_gen3_check_fw(struct cyapa *cyapa, const struct firmware *fw)
+{
+	struct device *dev = &cyapa->client->dev;
+	u16 csum;
+	u16 csum_expected;
+
+	/* Firmware must match exact 30848 bytes = 482 64-byte blocks. */
+	if (fw->size != CYAPA_FW_SIZE) {
+		dev_err(dev, "invalid firmware size = %zu, expected %u.\n",
+			fw->size, CYAPA_FW_SIZE);
+		return -EINVAL;
+	}
+
+	/* Verify header block */
+	csum_expected = (fw->data[0] << 8) | fw->data[1];
+	csum = cyapa_gen3_csum(&fw->data[2], CYAPA_FW_HDR_SIZE - 2);
+	if (csum != csum_expected) {
+		dev_err(dev, "%s %04x, expected: %04x\n",
+			"invalid firmware header checksum = ",
+			csum, csum_expected);
+		return -EINVAL;
+	}
+
+	/* Verify firmware image */
+	csum_expected = (fw->data[CYAPA_FW_HDR_SIZE - 2] << 8) |
+			 fw->data[CYAPA_FW_HDR_SIZE - 1];
+	csum = cyapa_gen3_csum(&fw->data[CYAPA_FW_HDR_SIZE],
+			CYAPA_FW_DATA_SIZE);
+	if (csum != csum_expected) {
+		dev_err(dev, "%s %04x, expected: %04x\n",
+			"invalid firmware header checksum = ",
+			csum, csum_expected);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+/*
+ * Write a |len| byte long buffer |buf| to the device, by chopping it up into a
+ * sequence of smaller |CYAPA_CMD_LEN|-length write commands.
+ *
+ * The data bytes for a write command are prepended with the 1-byte offset
+ * of the data relative to the start of |buf|.
+ */
+static int cyapa_gen3_write_buffer(struct cyapa *cyapa,
+		const u8 *buf, size_t len)
+{
+	int error;
+	size_t i;
+	unsigned char cmd[CYAPA_CMD_LEN + 1];
+	size_t cmd_len;
+
+	for (i = 0; i < len; i += CYAPA_CMD_LEN) {
+		const u8 *payload = &buf[i];
+
+		cmd_len = (len - i >= CYAPA_CMD_LEN) ? CYAPA_CMD_LEN : len - i;
+		cmd[0] = i;
+		memcpy(&cmd[1], payload, cmd_len);
+
+		error = cyapa_i2c_reg_write_block(cyapa, 0, cmd_len + 1, cmd);
+		if (error)
+			return error;
+	}
+	return 0;
+}
+
+/*
+ * A firmware block write command writes 64 bytes of data to a single flash
+ * page in the device.  The 78-byte block write command has the format:
+ *   <0xff> <CMD> <Key> <Start> <Data> <Data-Checksum> <CMD Checksum>
+ *
+ *  <0xff>  - every command starts with 0xff
+ *  <CMD>   - the write command value is 0x39
+ *  <Key>   - write commands include an 8-byte key: { 00 01 02 03 04 05 06 07 }
+ *  <Block> - Memory Block number (address / 64) (16-bit, big-endian)
+ *  <Data>  - 64 bytes of firmware image data
+ *  <Data Checksum> - sum of 64 <Data> bytes, modulo 0xff
+ *  <CMD Checksum> - sum of 77 bytes, from 0xff to <Data Checksum>
+ *
+ * Each write command is split into 5 i2c write transactions of up to 16 bytes.
+ * Each transaction starts with an i2c register offset: (00, 10, 20, 30, 40).
+ */
+static int cyapa_gen3_write_fw_block(struct cyapa *cyapa,
+		u16 block, const u8 *data)
+{
+	int ret;
+	struct gen3_write_block_cmd write_block_cmd;
+	u8 status[BL_STATUS_SIZE];
+	int tries;
+	u8 bl_status, bl_error;
+
+	/* Set write command and security key bytes. */
+	write_block_cmd.checksum_seed = GEN3_BL_CMD_CHECKSUM_SEED;
+	write_block_cmd.cmd_code = GEN3_BL_CMD_WRITE_BLOCK;
+	memcpy(write_block_cmd.key, security_key, sizeof(security_key));
+	put_unaligned_be16(block, &write_block_cmd.block_num);
+	memcpy(write_block_cmd.block_data, data, CYAPA_FW_BLOCK_SIZE);
+	write_block_cmd.block_checksum = cyapa_gen3_csum(
+			write_block_cmd.block_data, CYAPA_FW_BLOCK_SIZE);
+	write_block_cmd.cmd_checksum = cyapa_gen3_csum((u8 *)&write_block_cmd,
+			sizeof(write_block_cmd) - 1);
+
+	ret = cyapa_gen3_write_buffer(cyapa, (u8 *)&write_block_cmd,
+			sizeof(write_block_cmd));
+	if (ret)
+		return ret;
+
+	/* Wait for write to finish */
+	tries = 11;  /* Programming for one block can take about 100ms. */
+	do {
+		usleep_range(10000, 20000);
+
+		/* Check block write command result status. */
+		ret = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET,
+					       BL_STATUS_SIZE, status);
+		if (ret != BL_STATUS_SIZE)
+			return (ret < 0) ? ret : -EIO;
+	} while ((status[REG_BL_STATUS] & BL_STATUS_BUSY) && --tries);
+
+	/* Ignore WATCHDOG bit and reserved bits. */
+	bl_status = status[REG_BL_STATUS] & ~BL_STATUS_REV_MASK;
+	bl_error = status[REG_BL_ERROR] & ~BL_ERROR_RESERVED;
+
+	if (bl_status & BL_STATUS_BUSY)
+		ret = -ETIMEDOUT;
+	else if (bl_status != BL_STATUS_RUNNING ||
+		bl_error != BL_ERROR_BOOTLOADING)
+		ret = -EIO;
+	else
+		ret = 0;
+
+	return ret;
+}
+
+static int cyapa_gen3_write_blocks(struct cyapa *cyapa,
+		size_t start_block, size_t block_count,
+		const u8 *image_data)
+{
+	int error;
+	int i;
+
+	for (i = 0; i < block_count; i++) {
+		size_t block = start_block + i;
+		size_t addr = i * CYAPA_FW_BLOCK_SIZE;
+		const u8 *data = &image_data[addr];
+
+		error = cyapa_gen3_write_fw_block(cyapa, block, data);
+		if (error)
+			return error;
+	}
+	return 0;
+}
+
+static int cyapa_gen3_do_fw_update(struct cyapa *cyapa,
+		const struct firmware *fw)
+{
+	struct device *dev = &cyapa->client->dev;
+	int error;
+
+	/* First write data, starting at byte 128 of fw->data */
+	error = cyapa_gen3_write_blocks(cyapa,
+		CYAPA_FW_DATA_BLOCK_START, CYAPA_FW_DATA_BLOCK_COUNT,
+		&fw->data[CYAPA_FW_HDR_BLOCK_COUNT * CYAPA_FW_BLOCK_SIZE]);
+	if (error) {
+		dev_err(dev, "FW update aborted, write image: %d\n", error);
+		return error;
+	}
+
+	/* Then write checksum */
+	error = cyapa_gen3_write_blocks(cyapa,
+		CYAPA_FW_HDR_BLOCK_START, CYAPA_FW_HDR_BLOCK_COUNT,
+		&fw->data[0]);
+	if (error) {
+		dev_err(dev, "FW update aborted, write checksum: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
 /*
  * cyapa_get_wait_time_for_pwr_cmd
  *
@@ -791,10 +1091,19 @@ static int cyapa_gen3_irq_handler(struct cyapa *cyapa)
 }
 
 static int cyapa_gen3_initialize(struct cyapa *cyapa) { return 0; }
+static int cyapa_gen3_bl_initiate(struct cyapa *cyapa,
+		const struct firmware *fw) { return 0; }
 static int cyapa_gen3_empty_output_data(struct cyapa *cyapa,
 		u8 *buf, int *len, cb_sort func) { return 0; }
 
 const struct cyapa_dev_ops cyapa_gen3_ops = {
+	.check_fw = cyapa_gen3_check_fw,
+	.bl_enter = cyapa_gen3_bl_enter,
+	.bl_activate = cyapa_gen3_bl_activate,
+	.update_fw = cyapa_gen3_do_fw_update,
+	.bl_deactivate = cyapa_gen3_bl_deactivate,
+	.bl_initiate = cyapa_gen3_bl_initiate,
+
 	.initialize = cyapa_gen3_initialize,
 
 	.state_parse = cyapa_gen3_state_parse,