Documentation: e100: Update the Intel 10/100 driver doc

Over the years, several of the links have changed or are no longer valid
so update them.  In addition, the default values were incorrect for a
couple of parameters.

Converted the text file to the reStructuredText (RST) format, since the
Linux kernel documentation now uses this format for documentation.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

Documentation/networking/e100.txt → Documentation/networking/e100.rst

 Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
 ==============================================================
 
-March 15, 2011
+June 1, 2018
 
 Contents
 ========
@@ -36,16 +36,9 @@ Channel Bonding documentation can be found in the Linux kernel source:
 Identifying Your Adapter
 ========================
 
-For more information on how to identify your adapter, go to the Adapter &
-Driver ID Guide at:
-
-  http://support.intel.com/support/network/adapter/pro100/21397.htm
-
-For the latest Intel network drivers for Linux, refer to the following
-website. In the search field, enter your adapter name or type, or use the
-networking link on the left to search for your adapter:
-
-  http://downloadfinder.intel.com/scripts-df/support_intel.asp
+For information on how to identify your adapter, and for the latest Intel
+network drivers, refer to the Intel Support website:
+http://www.intel.com/support
 
 Driver Configuration Parameters
 ===============================
@@ -57,22 +50,26 @@ Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
    structure that describes a receive buffer and its attributes to the network
    controller. The data in the descriptor is used by the controller to write
    data from the controller to host memory. In the 3.x.x driver the valid range
-   for this parameter is 64-256. The default value is 64. This parameter can be
-   changed using the command:
+   for this parameter is 64-256. The default value is 256. This parameter can be
+   changed using the command::
 
-   ethtool -G eth? rx n, where n is the number of desired rx descriptors.
+   ethtool -G eth? rx n
+
+   Where n is the number of desired Rx descriptors.
 
 Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
    structure that describes a transmit buffer and its attributes to the network
    controller. The data in the descriptor is used by the controller to read
    data from the host memory to the controller. In the 3.x.x driver the valid
-   range for this parameter is 64-256. The default value is 64. This parameter
-   can be changed using the command:
+   range for this parameter is 64-256. The default value is 128. This parameter
+   can be changed using the command::
+
+   ethtool -G eth? tx n
 
-   ethtool -G eth? tx n, where n is the number of desired tx descriptors.
+   Where n is the number of desired Tx descriptors.
 
 Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
-   default. The ethtool utility can be used as follows to force speed/duplex.
+   default. The ethtool utility can be used as follows to force speed/duplex.::
 
    ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
 
@@ -81,7 +78,7 @@ Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
 
 Event Log Message Level:  The driver uses the message level flag to log events
    to syslog. The message level can be set at driver load time. It can also be
-   set using the command:
+   set using the command::
 
    ethtool -s eth? msglvl n
 
@@ -112,9 +109,9 @@ Additional Configurations
   ---------------------
   In order to see link messages and other Intel driver information on your
   console, you must set the dmesg level up to six. This can be done by
-  entering the following on the command line before loading the e100 driver:
+  entering the following on the command line before loading the e100 driver::
 
-       dmesg -n 8
+       dmesg -n 6
 
   If you wish to see all messages issued by the driver, including debug
   messages, set the dmesg level to eight.
@@ -146,7 +143,8 @@ Additional Configurations
 
   NAPI (Rx polling mode) is supported in the e100 driver.
 
-  See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
+  See https://wiki.linuxfoundation.org/networking/napi for more information
+  on NAPI.
 
   Multiple Interfaces on Same Ethernet Broadcast Network
   ------------------------------------------------------
@@ -160,7 +158,7 @@ Additional Configurations
   If you have multiple interfaces in a server, either turn on ARP
   filtering by
 
-  (1) entering: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+  (1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
       (this only works if your kernel's version is higher than 2.4.5), or
 
   (2) installing the interfaces in separate broadcast domains (either
@@ -169,15 +167,11 @@ Additional Configurations
 
 Support
 =======
-
 For general information, go to the Intel support website at:
+http://www.intel.com/support/
 
-    http://support.intel.com
-
-    or the Intel Wired Networking project hosted by Sourceforge at:
-
-    http://sourceforge.net/projects/e1000
-
-If an issue is identified with the released source code on the supported
-kernel with a supported adapter, email the specific information related to the
-issue to e1000-devel@lists.sourceforge.net.
+or the Intel Wired Networking project hosted by Sourceforge at:
+http://sourceforge.net/projects/e1000
+If an issue is identified with the released source code on a supported kernel
+with a supported adapter, email the specific information related to the issue
+to e1000-devel@lists.sf.net.

Documentation/networking/index.rst

@@ -10,6 +10,7 @@ Contents:
    batman-adv
    can
    dpaa2/index
+   e100
    kapi
    z8530book
    msg_zerocopy

MAINTAINERS

@@ -7089,7 +7089,7 @@ Q:	http://patchwork.ozlabs.org/project/intel-wired-lan/list/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue.git
 S:	Supported
-F:	Documentation/networking/e100.txt
+F:	Documentation/networking/e100.rst
 F:	Documentation/networking/e1000.txt
 F:	Documentation/networking/e1000e.txt
 F:	Documentation/networking/igb.txt