ARM: dts: omap3-igep0030-common: Add USB Host support

Provide RESET GPIO for the USB PHY, the USB Host port mode and
the PHY device for the controller. Also provides pin multiplexer
information for USB host pins.
Signed-off-by: NPau Pajuel <ppajuel@gmail.com>
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/boot/dts/omap3-igep0030-common.dtsi

@@ -33,9 +33,28 @@
 			 default-state = "off";
 		};
 	};
+
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;		/* gpio_54 */
+	};
 };
 
 &omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_pins>;
+
+	hsusb2_pins: pinmux_hsusb2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
+		>;
+	};
+
 	uart2_pins: pinmux_uart2_pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1)	/* mcbsp3_dx.uart2_cts */
@@ -47,6 +66,20 @@
 };
 
 &omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_core2_pins>;
+
+	hsusb2_core2_pins: pinmux_hsusb2_core2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		      /* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		      /* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+		>;
+	};
+
 	leds_core2_pins: pinmux_leds_core2_pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)	/* etk_d2.gpio_16 */
@@ -54,6 +87,14 @@
 	};
 };
 
+&usbhshost {
+	port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <0 &hsusb2_phy>;
+};
+
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart2_pins>;