ALSA: ALSA driver for SGI HAL2 audio device

This patch adds a new ALSA driver for the audio device found inside
many older SGI workstation (Indy, Indigo2). The hardware uses a SGI
custom chip, which feeds two codec chips, an IEC chip and a synth chip.
Currently only one of the codecs is supported. This driver already has
the same functionality as the HAL2 OSS driver and will replace it.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

sound/mips/Kconfig

@@ -9,6 +9,13 @@ menuconfig SND_MIPS
 
 if SND_MIPS
 
+config SND_SGI_HAL2
+        tristate "SGI HAL2 Audio"
+        depends on SGI_HAS_HAL2
+        help
+                Sound support for the SGI Indy and Indigo2 Workstation.
+
+
 config SND_AU1X00
 	tristate "Au1x00 AC97 Port Driver"
 	depends on SOC_AU1000 || SOC_AU1100 || SOC_AU1500

sound/mips/Makefile

@@ -3,6 +3,8 @@
 #
 
 snd-au1x00-objs := au1x00.o
+snd-sgi-hal2-objs := hal2.o
 
 # Toplevel Module Dependency
 obj-$(CONFIG_SND_AU1X00) += snd-au1x00.o
+obj-$(CONFIG_SND_SGI_HAL2) += snd-sgi-hal2.o

sound/mips/hal2.h

+#ifndef __HAL2_H
+#define __HAL2_H
+
+/*
+ *  Driver for HAL2 sound processors
+ *  Copyright (c) 1999 Ulf Carlsson <ulfc@bun.falkenberg.se>
+ *  Copyright (c) 2001, 2002, 2003 Ladislav Michl <ladis@linux-mips.org>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#include <linux/types.h>
+
+/* Indirect status register */
+
+#define H2_ISR_TSTATUS		0x01	/* RO: transaction status 1=busy */
+#define H2_ISR_USTATUS		0x02	/* RO: utime status bit 1=armed */
+#define H2_ISR_QUAD_MODE	0x04	/* codec mode 0=indigo 1=quad */
+#define H2_ISR_GLOBAL_RESET_N	0x08	/* chip global reset 0=reset */
+#define H2_ISR_CODEC_RESET_N	0x10	/* codec/synth reset 0=reset  */
+
+/* Revision register */
+
+#define H2_REV_AUDIO_PRESENT	0x8000	/* RO: audio present 0=present */
+#define H2_REV_BOARD_M		0x7000	/* RO: bits 14:12, board revision */
+#define H2_REV_MAJOR_CHIP_M	0x00F0	/* RO: bits 7:4, major chip revision */
+#define H2_REV_MINOR_CHIP_M	0x000F	/* RO: bits 3:0, minor chip revision */
+
+/* Indirect address register */
+
+/*
+ * Address of indirect internal register to be accessed. A write to this
+ * register initiates read or write access to the indirect registers in the
+ * HAL2. Note that there af four indirect data registers for write access to
+ * registers larger than 16 byte.
+ */
+
+#define H2_IAR_TYPE_M		0xF000	/* bits 15:12, type of functional */
+					/* block the register resides in */
+					/* 1=DMA Port */
+					/* 9=Global DMA Control */
+					/* 2=Bresenham */
+					/* 3=Unix Timer */
+#define H2_IAR_NUM_M		0x0F00	/* bits 11:8 instance of the */
+					/* blockin which the indirect */
+					/* register resides */
+					/* If IAR_TYPE_M=DMA Port: */
+					/* 1=Synth In */
+					/* 2=AES In */
+					/* 3=AES Out */
+					/* 4=DAC Out */
+					/* 5=ADC Out */
+					/* 6=Synth Control */
+					/* If IAR_TYPE_M=Global DMA Control: */
+					/* 1=Control */
+					/* If IAR_TYPE_M=Bresenham: */
+					/* 1=Bresenham Clock Gen 1 */
+					/* 2=Bresenham Clock Gen 2 */
+					/* 3=Bresenham Clock Gen 3 */
+					/* If IAR_TYPE_M=Unix Timer: */
+					/* 1=Unix Timer */
+#define H2_IAR_ACCESS_SELECT	0x0080	/* 1=read 0=write */
+#define H2_IAR_PARAM		0x000C	/* Parameter Select */
+#define H2_IAR_RB_INDEX_M	0x0003	/* Read Back Index */
+					/* 00:word0 */
+					/* 01:word1 */
+					/* 10:word2 */
+					/* 11:word3 */
+/*
+ * HAL2 internal addressing
+ *
+ * The HAL2 has "indirect registers" (idr) which are accessed by writing to the
+ * Indirect Data registers. Write the address to the Indirect Address register
+ * to transfer the data.
+ *
+ * We define the H2IR_* to the read address and H2IW_* to the write address and
+ * H2I_* to be fields in whatever register is referred to.
+ *
+ * When we write to indirect registers which are larger than one word (16 bit)
+ * we have to fill more than one indirect register before writing. When we read
+ * back however we have to read several times, each time with different Read
+ * Back Indexes (there are defs for doing this easily).
+ */
+
+/*
+ * Relay Control
+ */
+#define H2I_RELAY_C		0x9100
+#define H2I_RELAY_C_STATE	0x01		/* state of RELAY pin signal */
+
+/* DMA port enable */
+
+#define H2I_DMA_PORT_EN		0x9104
+#define H2I_DMA_PORT_EN_SY_IN	0x01		/* Synth_in DMA port */
+#define H2I_DMA_PORT_EN_AESRX	0x02		/* AES receiver DMA port */
+#define H2I_DMA_PORT_EN_AESTX	0x04		/* AES transmitter DMA port */
+#define H2I_DMA_PORT_EN_CODECTX	0x08		/* CODEC transmit DMA port */
+#define H2I_DMA_PORT_EN_CODECR	0x10		/* CODEC receive DMA port */
+
+#define H2I_DMA_END		0x9108 		/* global dma endian select */
+#define H2I_DMA_END_SY_IN	0x01		/* Synth_in DMA port */
+#define H2I_DMA_END_AESRX	0x02		/* AES receiver DMA port */
+#define H2I_DMA_END_AESTX	0x04		/* AES transmitter DMA port */
+#define H2I_DMA_END_CODECTX	0x08		/* CODEC transmit DMA port */
+#define H2I_DMA_END_CODECR	0x10		/* CODEC receive DMA port */
+						/* 0=b_end 1=l_end */
+
+#define H2I_DMA_DRV		0x910C  	/* global PBUS DMA enable */
+
+#define H2I_SYNTH_C		0x1104		/* Synth DMA control */
+
+#define H2I_AESRX_C		0x1204	 	/* AES RX dma control */
+
+#define H2I_C_TS_EN		0x20		/* Timestamp enable */
+#define H2I_C_TS_FRMT		0x40		/* Timestamp format */
+#define H2I_C_NAUDIO		0x80		/* Sign extend */
+
+/* AESRX CTL, 16 bit */
+
+#define H2I_AESTX_C		0x1304		/* AES TX DMA control */
+#define H2I_AESTX_C_CLKID_SHIFT	3		/* Bresenham Clock Gen 1-3 */
+#define H2I_AESTX_C_CLKID_M	0x18
+#define H2I_AESTX_C_DATAT_SHIFT	8		/* 1=mono 2=stereo (3=quad) */
+#define H2I_AESTX_C_DATAT_M	0x300
+
+/* CODEC registers */
+
+#define H2I_DAC_C1		0x1404 		/* DAC DMA control, 16 bit */
+#define H2I_DAC_C2		0x1408		/* DAC DMA control, 32 bit */
+#define H2I_ADC_C1		0x1504 		/* ADC DMA control, 16 bit */
+#define H2I_ADC_C2		0x1508		/* ADC DMA control, 32 bit */
+
+/* Bits in CTL1 register */
+
+#define H2I_C1_DMA_SHIFT	0		/* DMA channel */
+#define H2I_C1_DMA_M		0x7
+#define H2I_C1_CLKID_SHIFT	3		/* Bresenham Clock Gen 1-3 */
+#define H2I_C1_CLKID_M		0x18
+#define H2I_C1_DATAT_SHIFT	8		/* 1=mono 2=stereo (3=quad) */
+#define H2I_C1_DATAT_M		0x300
+
+/* Bits in CTL2 register */
+
+#define H2I_C2_R_GAIN_SHIFT	0		/* right a/d input gain */
+#define H2I_C2_R_GAIN_M		0xf
+#define H2I_C2_L_GAIN_SHIFT	4		/* left a/d input gain */
+#define H2I_C2_L_GAIN_M		0xf0
+#define H2I_C2_R_SEL		0x100		/* right input select */
+#define H2I_C2_L_SEL		0x200		/* left input select */
+#define H2I_C2_MUTE		0x400		/* mute */
+#define H2I_C2_DO1		0x00010000	/* digital output port bit 0 */
+#define H2I_C2_DO2		0x00020000	/* digital output port bit 1 */
+#define H2I_C2_R_ATT_SHIFT	18		/* right d/a output - */
+#define H2I_C2_R_ATT_M		0x007c0000	/* attenuation */
+#define H2I_C2_L_ATT_SHIFT	23		/* left d/a output - */
+#define H2I_C2_L_ATT_M		0x0f800000	/* attenuation */
+
+#define H2I_SYNTH_MAP_C		0x1104		/* synth dma handshake ctrl */
+
+/* Clock generator CTL 1, 16 bit */
+
+#define H2I_BRES1_C1		0x2104
+#define H2I_BRES2_C1		0x2204
+#define H2I_BRES3_C1		0x2304
+
+#define H2I_BRES_C1_SHIFT	0		/* 0=48.0 1=44.1 2=aes_rx */
+#define H2I_BRES_C1_M		0x03
+
+/* Clock generator CTL 2, 32 bit */
+
+#define H2I_BRES1_C2		0x2108
+#define H2I_BRES2_C2		0x2208
+#define H2I_BRES3_C2		0x2308
+
+#define H2I_BRES_C2_INC_SHIFT	0		/* increment value */
+#define H2I_BRES_C2_INC_M	0xffff
+#define H2I_BRES_C2_MOD_SHIFT	16		/* modcontrol value */
+#define H2I_BRES_C2_MOD_M	0xffff0000	/* modctrl=0xffff&(modinc-1) */
+
+/* Unix timer, 64 bit */
+
+#define H2I_UTIME		0x3104
+#define H2I_UTIME_0_LD		0xffff		/* microseconds, LSB's */
+#define H2I_UTIME_1_LD0		0x0f		/* microseconds, MSB's */
+#define H2I_UTIME_1_LD1		0xf0		/* tenths of microseconds */
+#define H2I_UTIME_2_LD		0xffff		/* seconds, LSB's */
+#define H2I_UTIME_3_LD		0xffff		/* seconds, MSB's */
+
+struct hal2_ctl_regs {
+	u32 _unused0[4];
+	u32 isr;		/* 0x10 Status Register */
+	u32 _unused1[3];
+	u32 rev;		/* 0x20 Revision Register */
+	u32 _unused2[3];
+	u32 iar;		/* 0x30 Indirect Address Register */
+	u32 _unused3[3];
+	u32 idr0;		/* 0x40 Indirect Data Register 0 */
+	u32 _unused4[3];
+	u32 idr1;		/* 0x50 Indirect Data Register 1 */
+	u32 _unused5[3];
+	u32 idr2;		/* 0x60 Indirect Data Register 2 */
+	u32 _unused6[3];
+	u32 idr3;		/* 0x70 Indirect Data Register 3 */
+};
+
+struct hal2_aes_regs {
+	u32 rx_stat[2];	/* Status registers */
+	u32 rx_cr[2];		/* Control registers */
+	u32 rx_ud[4];		/* User data window */
+	u32 rx_st[24];		/* Channel status data */
+
+	u32 tx_stat[1];	/* Status register */
+	u32 tx_cr[3];		/* Control registers */
+	u32 tx_ud[4];		/* User data window */
+	u32 tx_st[24];		/* Channel status data */
+};
+
+struct hal2_vol_regs {
+	u32 right;		/* Right volume */
+	u32 left;		/* Left volume */
+};
+
+struct hal2_syn_regs {
+	u32 _unused0[2];
+	u32 page;		/* DOC Page register */
+	u32 regsel;		/* DOC Register selection */
+	u32 dlow;		/* DOC Data low */
+	u32 dhigh;		/* DOC Data high */
+	u32 irq;		/* IRQ Status */
+	u32 dram;		/* DRAM Access */
+};
+
+#endif	/* __HAL2_H */