Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
提交 782d8a3c 编写于 作者: K Kukjin Kim
浏览文件
操作

ARM: SAMSUNG: Update the name of regarding Samsung GPIO 

According to gpio-samsung.c, this patch updates the name of
regarding Samsung GPIO. Basically the samsung_xxx prefix is
used in gpio-samsung.c instead of s3c_xxx, because unified
name can reduce its complexity.

Note: some s3c_xxx stil remains because it is used widely.
It will be updated next time.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
上级 1b39d5f2
隐藏空白更改
内联 并排
Showing with 250 addition and 384 deletion
arch/arm/mach-exynos4/include/mach/pm-core.h
浏览文件 @ 782d8a3c
...@@ -53,7 +53,7 @@ static inline void s3c_pm_restored_gpios(void) ...@@ -53,7 +53,7 @@ static inline void s3c_pm_restored_gpios(void)
/* nothing here yet */ /* nothing here yet */
} }
static inline void s3c_pm_saved_gpios(void) static inline void samsung_pm_saved_gpios(void)
{ {
/* nothing here yet */ /* nothing here yet */
} }
arch/arm/mach-s3c2410/include/mach/gpio-fns.h
浏览文件 @ 782d8a3c
/* arch/arm/mach-s3c2410/include/mach/gpio-fns.h #include <plat/gpio-fns.h>
*
* Copyright (c) 2003-2009 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - hardware
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef __MACH_GPIO_FNS_H
#define __MACH_GPIO_FNS_H __FILE__
/* These functions are in the to-be-removed category and it is strongly
* encouraged not to use these in new code. They will be marked deprecated
* very soon.
*
* Most of the functionality can be either replaced by the gpiocfg calls
* for the s3c platform or by the generic GPIOlib API.
*
* As of 2.6.35-rc, these will be removed, with the few drivers using them
* either replaced or given a wrapper until the calls can be removed.
*/
#include <plat/gpio-cfg.h>
static inline void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int cfg)
{
/* 1:1 mapping between cfgpin and setcfg calls at the moment */
s3c_gpio_cfgpin(pin, cfg);
}
/* external functions for GPIO support
*
* These allow various different clients to access the same GPIO
* registers without conflicting. If your driver only owns the entire
* GPIO register, then it is safe to ioremap/__raw_{read|write} to it.
*/
extern unsigned int s3c2410_gpio_getcfg(unsigned int pin);
/* s3c2410_gpio_getirq
*
* turn the given pin number into the corresponding IRQ number
*
* returns:
* < 0 = no interrupt for this pin
* >=0 = interrupt number for the pin
*/
extern int s3c2410_gpio_getirq(unsigned int pin);
/* s3c2410_gpio_irqfilter
*
* set the irq filtering on the given pin
*
* on = 0 => disable filtering
* 1 => enable filtering
*
* config = S3C2410_EINTFLT_PCLK or S3C2410_EINTFLT_EXTCLK orred with
* width of filter (0 through 63)
*
*
*/
extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
unsigned int config);
/* s3c2410_gpio_pullup
*
* This call should be replaced with s3c_gpio_setpull().
*
* As a note, there is currently no distinction between pull-up and pull-down
* in the s3c24xx series devices with only an on/off configuration.
*/
/* s3c2410_gpio_pullup
*
* configure the pull-up control on the given pin
*
* to = 1 => disable the pull-up
* 0 => enable the pull-up
*
* eg;
*
* s3c2410_gpio_pullup(S3C2410_GPB(0), 0);
* s3c2410_gpio_pullup(S3C2410_GPE(8), 0);
*/
extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to);
extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
extern unsigned int s3c2410_gpio_getpin(unsigned int pin);
#endif /* __MACH_GPIO_FNS_H */
arch/arm/mach-s3c2410/include/mach/gpio-track.h
浏览文件 @ 782d8a3c
...@@ -17,11 +17,11 @@ ...@@ -17,11 +17,11 @@
#include <mach/regs-gpio.h> #include <mach/regs-gpio.h>
extern struct s3c_gpio_chip s3c24xx_gpios[]; extern struct samsung_gpio_chip s3c24xx_gpios[];
static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin) static inline struct samsung_gpio_chip *samsung_gpiolib_getchip(unsigned int pin)
{ {
struct s3c_gpio_chip *chip; struct samsung_gpio_chip *chip;
if (pin > S3C_GPIO_END) if (pin > S3C_GPIO_END)
return NULL; return NULL;
......
arch/arm/mach-s3c2410/include/mach/pm-core.h
浏览文件 @ 782d8a3c
...@@ -64,4 +64,4 @@ static inline void s3c_pm_arch_update_uart(void __iomem *regs, ...@@ -64,4 +64,4 @@ static inline void s3c_pm_arch_update_uart(void __iomem *regs,
} }
static inline void s3c_pm_restored_gpios(void) { } static inline void s3c_pm_restored_gpios(void) { }
static inline void s3c_pm_saved_gpios(void) { } static inline void samsung_pm_saved_gpios(void) { }
arch/arm/mach-s3c2410/s3c2410.c
浏览文件 @ 782d8a3c
...@@ -72,8 +72,8 @@ void __init s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no) ...@@ -72,8 +72,8 @@ void __init s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no)
void __init s3c2410_map_io(void) void __init s3c2410_map_io(void)
{ {
s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1up; s3c24xx_gpiocfg_default.set_pull = s3c24xx_gpio_setpull_1up;
s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1up; s3c24xx_gpiocfg_default.get_pull = s3c24xx_gpio_getpull_1up;
iotable_init(s3c2410_iodesc, ARRAY_SIZE(s3c2410_iodesc)); iotable_init(s3c2410_iodesc, ARRAY_SIZE(s3c2410_iodesc));
} }
......
arch/arm/mach-s3c2412/gpio.c
浏览文件 @ 782d8a3c
...@@ -28,7 +28,7 @@ ...@@ -28,7 +28,7 @@
int s3c2412_gpio_set_sleepcfg(unsigned int pin, unsigned int state) int s3c2412_gpio_set_sleepcfg(unsigned int pin, unsigned int state)
{ {
struct s3c_gpio_chip *chip = s3c_gpiolib_getchip(pin); struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin);
unsigned long offs = pin - chip->chip.base; unsigned long offs = pin - chip->chip.base;
unsigned long flags; unsigned long flags;
unsigned long slpcon; unsigned long slpcon;
......
arch/arm/mach-s3c2416/s3c2416.c
浏览文件 @ 782d8a3c
...@@ -118,8 +118,8 @@ void __init s3c2416_init_uarts(struct s3c2410_uartcfg *cfg, int no) ...@@ -118,8 +118,8 @@ void __init s3c2416_init_uarts(struct s3c2410_uartcfg *cfg, int no)
void __init s3c2416_map_io(void) void __init s3c2416_map_io(void)
{ {
s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_updown; s3c24xx_gpiocfg_default.set_pull = samsung_gpio_setpull_updown;
s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_updown; s3c24xx_gpiocfg_default.get_pull = samsung_gpio_getpull_updown;
/* initialize device information early */ /* initialize device information early */
s3c2416_default_sdhci0(); s3c2416_default_sdhci0();
......
arch/arm/mach-s3c2440/s3c2440.c
浏览文件 @ 782d8a3c
...@@ -68,6 +68,6 @@ void __init s3c2440_map_io(void) ...@@ -68,6 +68,6 @@ void __init s3c2440_map_io(void)
{ {
s3c244x_map_io(); s3c244x_map_io();
s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1up; s3c24xx_gpiocfg_default.set_pull = s3c24xx_gpio_setpull_1up;
s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1up; s3c24xx_gpiocfg_default.get_pull = s3c24xx_gpio_getpull_1up;
} }
arch/arm/mach-s3c2440/s3c2442.c
浏览文件 @ 782d8a3c
...@@ -180,6 +180,6 @@ void __init s3c2442_map_io(void) ...@@ -180,6 +180,6 @@ void __init s3c2442_map_io(void)
{ {
s3c244x_map_io(); s3c244x_map_io();
s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1down; s3c24xx_gpiocfg_default.set_pull = s3c24xx_gpio_setpull_1down;
s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1down; s3c24xx_gpiocfg_default.get_pull = s3c24xx_gpio_getpull_1down;
} }
arch/arm/mach-s3c2443/s3c2443.c
浏览文件 @ 782d8a3c
...@@ -90,8 +90,8 @@ void __init s3c2443_init_uarts(struct s3c2410_uartcfg *cfg, int no) ...@@ -90,8 +90,8 @@ void __init s3c2443_init_uarts(struct s3c2410_uartcfg *cfg, int no)
void __init s3c2443_map_io(void) void __init s3c2443_map_io(void)
{ {
s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_s3c2443; s3c24xx_gpiocfg_default.set_pull = s3c2443_gpio_setpull;
s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_s3c2443; s3c24xx_gpiocfg_default.get_pull = s3c2443_gpio_getpull;
iotable_init(s3c2443_iodesc, ARRAY_SIZE(s3c2443_iodesc)); iotable_init(s3c2443_iodesc, ARRAY_SIZE(s3c2443_iodesc));
} }
......
arch/arm/mach-s3c64xx/include/mach/pm-core.h
浏览文件 @ 782d8a3c
...@@ -104,7 +104,7 @@ static inline void s3c_pm_restored_gpios(void) ...@@ -104,7 +104,7 @@ static inline void s3c_pm_restored_gpios(void)
__raw_writel(0, S3C64XX_SLPEN); __raw_writel(0, S3C64XX_SLPEN);
} }
static inline void s3c_pm_saved_gpios(void) static inline void samsung_pm_saved_gpios(void)
{ {
/* turn on the sleep mode and keep it there, as it seems that during /* turn on the sleep mode and keep it there, as it seems that during
* suspend the xCON registers get re-set and thus you can end up with * suspend the xCON registers get re-set and thus you can end up with
......
arch/arm/mach-s5pv210/include/mach/pm-core.h
浏览文件 @ 782d8a3c
...@@ -43,4 +43,4 @@ static inline void s3c_pm_arch_update_uart(void __iomem *regs, ...@@ -43,4 +43,4 @@ static inline void s3c_pm_arch_update_uart(void __iomem *regs,
} }
static inline void s3c_pm_restored_gpios(void) { } static inline void s3c_pm_restored_gpios(void) { }
static inline void s3c_pm_saved_gpios(void) { } static inline void samsung_pm_saved_gpios(void) { }
arch/arm/plat-s5p/irq-gpioint.c
浏览文件 @ 782d8a3c
...@@ -37,7 +37,7 @@ struct s5p_gpioint_bank { ...@@ -37,7 +37,7 @@ struct s5p_gpioint_bank {
int start; int start;
int nr_groups; int nr_groups;
int irq; int irq;
struct s3c_gpio_chip **chips; struct samsung_gpio_chip **chips;
void (*handler)(unsigned int, struct irq_desc *); void (*handler)(unsigned int, struct irq_desc *);
}; };
...@@ -87,7 +87,7 @@ static void s5p_gpioint_handler(unsigned int irq, struct irq_desc *desc) ...@@ -87,7 +87,7 @@ static void s5p_gpioint_handler(unsigned int irq, struct irq_desc *desc)
chained_irq_enter(chip, desc); chained_irq_enter(chip, desc);
for (group = 0; group < bank->nr_groups; group++) { for (group = 0; group < bank->nr_groups; group++) {
struct s3c_gpio_chip *chip = bank->chips[group]; struct samsung_gpio_chip *chip = bank->chips[group];
if (!chip) if (!chip)
continue; continue;
...@@ -110,7 +110,7 @@ static void s5p_gpioint_handler(unsigned int irq, struct irq_desc *desc) ...@@ -110,7 +110,7 @@ static void s5p_gpioint_handler(unsigned int irq, struct irq_desc *desc)
chained_irq_exit(chip, desc); chained_irq_exit(chip, desc);
} }
static __init int s5p_gpioint_add(struct s3c_gpio_chip *chip) static __init int s5p_gpioint_add(struct samsung_gpio_chip *chip)
{ {
static int used_gpioint_groups = 0; static int used_gpioint_groups = 0;
int group = chip->group; int group = chip->group;
...@@ -130,7 +130,7 @@ static __init int s5p_gpioint_add(struct s3c_gpio_chip *chip) ...@@ -130,7 +130,7 @@ static __init int s5p_gpioint_add(struct s3c_gpio_chip *chip)
return -EINVAL; return -EINVAL;
if (!bank->handler) { if (!bank->handler) {
bank->chips = kzalloc(sizeof(struct s3c_gpio_chip *) * bank->chips = kzalloc(sizeof(struct samsung_gpio_chip *) *
bank->nr_groups, GFP_KERNEL); bank->nr_groups, GFP_KERNEL);
if (!bank->chips) if (!bank->chips)
return -ENOMEM; return -ENOMEM;
...@@ -173,7 +173,7 @@ static __init int s5p_gpioint_add(struct s3c_gpio_chip *chip) ...@@ -173,7 +173,7 @@ static __init int s5p_gpioint_add(struct s3c_gpio_chip *chip)
int __init s5p_register_gpio_interrupt(int pin) int __init s5p_register_gpio_interrupt(int pin)
{ {
struct s3c_gpio_chip *my_chip = s3c_gpiolib_getchip(pin); struct samsung_gpio_chip *my_chip = samsung_gpiolib_getchip(pin);
int offset, group; int offset, group;
int ret; int ret;
......
arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h
浏览文件 @ 782d8a3c
/* linux/arch/arm/plat-s3c/include/plat/gpio-cfg-helper.h /* linux/arch/arm/plat-samsung/include/plat/gpio-cfg-helper.h
* *
* Copyright 2008 Openmoko, Inc. * Copyright 2008 Openmoko, Inc.
* Copyright 2008 Simtec Electronics * Copyright 2008 Simtec Electronics
* http://armlinux.simtec.co.uk/ * http://armlinux.simtec.co.uk/
* Ben Dooks <ben@simtec.co.uk> * Ben Dooks <ben@simtec.co.uk>
* *
* S3C Platform - GPIO pin configuration helper definitions * Samsung Platform - GPIO pin configuration helper definitions
* *
* This program is free software; you can redistribute it and/or modify * This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as * it under the terms of the GNU General Public License version 2 as
...@@ -24,120 +24,30 @@ ...@@ -24,120 +24,30 @@
* by disabling interrupts. * by disabling interrupts.
*/ */
static inline int s3c_gpio_do_setcfg(struct s3c_gpio_chip *chip, static inline int samsung_gpio_do_setcfg(struct samsung_gpio_chip *chip,
unsigned int off, unsigned int config) unsigned int off, unsigned int config)
{ {
return (chip->config->set_config)(chip, off, config); return (chip->config->set_config)(chip, off, config);
} }
static inline unsigned s3c_gpio_do_getcfg(struct s3c_gpio_chip *chip, static inline unsigned samsung_gpio_do_getcfg(struct samsung_gpio_chip *chip,
unsigned int off) unsigned int off)
{ {
return (chip->config->get_config)(chip, off); return (chip->config->get_config)(chip, off);
} }
static inline int s3c_gpio_do_setpull(struct s3c_gpio_chip *chip, static inline int samsung_gpio_do_setpull(struct samsung_gpio_chip *chip,
unsigned int off, s3c_gpio_pull_t pull) unsigned int off, samsung_gpio_pull_t pull)
{ {
return (chip->config->set_pull)(chip, off, pull); return (chip->config->set_pull)(chip, off, pull);
} }
static inline s3c_gpio_pull_t s3c_gpio_do_getpull(struct s3c_gpio_chip *chip, static inline samsung_gpio_pull_t samsung_gpio_do_getpull(struct samsung_gpio_chip *chip,
unsigned int off) unsigned int off)
{ {
return chip->config->get_pull(chip, off); return chip->config->get_pull(chip, off);
} }
/**
* s3c_gpio_setcfg_s3c24xx - S3C24XX style GPIO configuration.
* @chip: The gpio chip that is being configured.
* @off: The offset for the GPIO being configured.
* @cfg: The configuration value to set.
*
* This helper deal with the GPIO cases where the control register
* has two bits of configuration per gpio, which have the following
* functions:
* 00 = input
* 01 = output
* 1x = special function
*/
extern int s3c_gpio_setcfg_s3c24xx(struct s3c_gpio_chip *chip,
unsigned int off, unsigned int cfg);
/**
* s3c_gpio_getcfg_s3c24xx - S3C24XX style GPIO configuration read.
* @chip: The gpio chip that is being configured.
* @off: The offset for the GPIO being configured.
*
* The reverse of s3c_gpio_setcfg_s3c24xx(). Will return a value whicg
* could be directly passed back to s3c_gpio_setcfg_s3c24xx(), from the
* S3C_GPIO_SPECIAL() macro.
*/
unsigned int s3c_gpio_getcfg_s3c24xx(struct s3c_gpio_chip *chip,
unsigned int off);
/**
* s3c_gpio_setcfg_s3c24xx_a - S3C24XX style GPIO configuration (Bank A)
* @chip: The gpio chip that is being configured.
* @off: The offset for the GPIO being configured.
* @cfg: The configuration value to set.
*
* This helper deal with the GPIO cases where the control register
* has one bit of configuration for the gpio, where setting the bit
* means the pin is in special function mode and unset means output.
*/
extern int s3c_gpio_setcfg_s3c24xx_a(struct s3c_gpio_chip *chip,
unsigned int off, unsigned int cfg);
/**
* s3c_gpio_getcfg_s3c24xx_a - S3C24XX style GPIO configuration read (Bank A)
* @chip: The gpio chip that is being configured.
* @off: The offset for the GPIO being configured.
*
* The reverse of s3c_gpio_setcfg_s3c24xx_a() turning an GPIO into a usable
* GPIO configuration value.
*
* @sa s3c_gpio_getcfg_s3c24xx
* @sa s3c_gpio_getcfg_s3c64xx_4bit
*/
extern unsigned s3c_gpio_getcfg_s3c24xx_a(struct s3c_gpio_chip *chip,
unsigned int off);
/**
* s3c_gpio_setcfg_s3c64xx_4bit - S3C64XX 4bit single register GPIO config.
* @chip: The gpio chip that is being configured.
* @off: The offset for the GPIO being configured.
* @cfg: The configuration value to set.
*
* This helper deal with the GPIO cases where the control register has 4 bits
* of control per GPIO, generally in the form of:
* 0000 = Input
* 0001 = Output
* others = Special functions (dependent on bank)
*
* Note, since the code to deal with the case where there are two control
* registers instead of one, we do not have a separate set of functions for
* each case.
*/
extern int s3c_gpio_setcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip,
unsigned int off, unsigned int cfg);
/**
* s3c_gpio_getcfg_s3c64xx_4bit - S3C64XX 4bit single register GPIO config read.
* @chip: The gpio chip that is being configured.
* @off: The offset for the GPIO being configured.
*
* The reverse of s3c_gpio_setcfg_s3c64xx_4bit(), turning a gpio configuration
* register setting into a value the software can use, such as could be passed
* to s3c_gpio_setcfg_s3c64xx_4bit().
*
* @sa s3c_gpio_getcfg_s3c24xx
*/
extern unsigned s3c_gpio_getcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip,
unsigned int off);
/* Pull-{up,down} resistor controls. /* Pull-{up,down} resistor controls.
* *
* S3C2410,S3C2440 = Pull-UP, * S3C2410,S3C2440 = Pull-UP,
...@@ -147,7 +57,7 @@ extern unsigned s3c_gpio_getcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip, ...@@ -147,7 +57,7 @@ extern unsigned s3c_gpio_getcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip,
*/ */
/** /**
* s3c_gpio_setpull_1up() - Pull configuration for choice of up or none. * s3c24xx_gpio_setpull_1up() - Pull configuration for choice of up or none.
* @chip: The gpio chip that is being configured. * @chip: The gpio chip that is being configured.
* @off: The offset for the GPIO being configured. * @off: The offset for the GPIO being configured.
* @param: pull: The pull mode being requested. * @param: pull: The pull mode being requested.
...@@ -155,11 +65,11 @@ extern unsigned s3c_gpio_getcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip, ...@@ -155,11 +65,11 @@ extern unsigned s3c_gpio_getcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip,
* This is a helper function for the case where we have GPIOs with one * This is a helper function for the case where we have GPIOs with one
* bit configuring the presence of a pull-up resistor. * bit configuring the presence of a pull-up resistor.
*/ */
extern int s3c_gpio_setpull_1up(struct s3c_gpio_chip *chip, extern int s3c24xx_gpio_setpull_1up(struct samsung_gpio_chip *chip,
unsigned int off, s3c_gpio_pull_t pull); unsigned int off, samsung_gpio_pull_t pull);
/** /**
* s3c_gpio_setpull_1down() - Pull configuration for choice of down or none * s3c24xx_gpio_setpull_1down() - Pull configuration for choice of down or none
* @chip: The gpio chip that is being configured * @chip: The gpio chip that is being configured
* @off: The offset for the GPIO being configured * @off: The offset for the GPIO being configured
* @param: pull: The pull mode being requested * @param: pull: The pull mode being requested
...@@ -167,11 +77,13 @@ extern int s3c_gpio_setpull_1up(struct s3c_gpio_chip *chip, ...@@ -167,11 +77,13 @@ extern int s3c_gpio_setpull_1up(struct s3c_gpio_chip *chip,
* This is a helper function for the case where we have GPIOs with one * This is a helper function for the case where we have GPIOs with one
* bit configuring the presence of a pull-down resistor. * bit configuring the presence of a pull-down resistor.
*/ */
extern int s3c_gpio_setpull_1down(struct s3c_gpio_chip *chip, extern int s3c24xx_gpio_setpull_1down(struct samsung_gpio_chip *chip,
unsigned int off, s3c_gpio_pull_t pull); unsigned int off, samsung_gpio_pull_t pull);
/** /**
* s3c_gpio_setpull_upown() - Pull configuration for choice of up, down or none * samsung_gpio_setpull_upown() - Pull configuration for choice of up,
* down or none
*
* @chip: The gpio chip that is being configured. * @chip: The gpio chip that is being configured.
* @off: The offset for the GPIO being configured. * @off: The offset for the GPIO being configured.
* @param: pull: The pull mode being requested. * @param: pull: The pull mode being requested.
...@@ -183,45 +95,46 @@ extern int s3c_gpio_setpull_1down(struct s3c_gpio_chip *chip, ...@@ -183,45 +95,46 @@ extern int s3c_gpio_setpull_1down(struct s3c_gpio_chip *chip,
* 01 = Pull-up resistor connected * 01 = Pull-up resistor connected
* 10 = Pull-down resistor connected * 10 = Pull-down resistor connected
*/ */
extern int s3c_gpio_setpull_updown(struct s3c_gpio_chip *chip, extern int samsung_gpio_setpull_updown(struct samsung_gpio_chip *chip,
unsigned int off, s3c_gpio_pull_t pull); unsigned int off, samsung_gpio_pull_t pull);
/** /**
* s3c_gpio_getpull_updown() - Get configuration for choice of up, down or none * samsung_gpio_getpull_updown() - Get configuration for choice of up,
* down or none
*
* @chip: The gpio chip that the GPIO pin belongs to * @chip: The gpio chip that the GPIO pin belongs to
* @off: The offset to the pin to get the configuration of. * @off: The offset to the pin to get the configuration of.
* *
* This helper function reads the state of the pull-{up,down} resistor for the * This helper function reads the state of the pull-{up,down} resistor
* given GPIO in the same case as s3c_gpio_setpull_upown. * for the given GPIO in the same case as samsung_gpio_setpull_upown.
*/ */
extern s3c_gpio_pull_t s3c_gpio_getpull_updown(struct s3c_gpio_chip *chip, extern samsung_gpio_pull_t samsung_gpio_getpull_updown(struct samsung_gpio_chip *chip,
unsigned int off); unsigned int off);
/** /**
* s3c_gpio_getpull_1up() - Get configuration for choice of up or none * s3c24xx_gpio_getpull_1up() - Get configuration for choice of up or none
* @chip: The gpio chip that the GPIO pin belongs to * @chip: The gpio chip that the GPIO pin belongs to
* @off: The offset to the pin to get the configuration of. * @off: The offset to the pin to get the configuration of.
* *
* This helper function reads the state of the pull-up resistor for the * This helper function reads the state of the pull-up resistor for the
* given GPIO in the same case as s3c_gpio_setpull_1up. * given GPIO in the same case as s3c24xx_gpio_setpull_1up.
*/ */
extern s3c_gpio_pull_t s3c_gpio_getpull_1up(struct s3c_gpio_chip *chip, extern samsung_gpio_pull_t s3c24xx_gpio_getpull_1up(struct samsung_gpio_chip *chip,
unsigned int off); unsigned int off);
/** /**
* s3c_gpio_getpull_1down() - Get configuration for choice of down or none * s3c24xx_gpio_getpull_1down() - Get configuration for choice of down or none
* @chip: The gpio chip that the GPIO pin belongs to * @chip: The gpio chip that the GPIO pin belongs to
* @off: The offset to the pin to get the configuration of. * @off: The offset to the pin to get the configuration of.
* *
* This helper function reads the state of the pull-down resistor for the * This helper function reads the state of the pull-down resistor for the
* given GPIO in the same case as s3c_gpio_setpull_1down. * given GPIO in the same case as s3c24xx_gpio_setpull_1down.
*/ */
extern s3c_gpio_pull_t s3c_gpio_getpull_1down(struct s3c_gpio_chip *chip, extern samsung_gpio_pull_t s3c24xx_gpio_getpull_1down(struct samsung_gpio_chip *chip,
unsigned int off); unsigned int off);
/** /**
* s3c_gpio_setpull_s3c2443() - Pull configuration for s3c2443. * s3c2443_gpio_setpull() - Pull configuration for s3c2443.
* @chip: The gpio chip that is being configured. * @chip: The gpio chip that is being configured.
* @off: The offset for the GPIO being configured. * @off: The offset for the GPIO being configured.
* @param: pull: The pull mode being requested. * @param: pull: The pull mode being requested.
...@@ -233,19 +146,18 @@ extern s3c_gpio_pull_t s3c_gpio_getpull_1down(struct s3c_gpio_chip *chip, ...@@ -233,19 +146,18 @@ extern s3c_gpio_pull_t s3c_gpio_getpull_1down(struct s3c_gpio_chip *chip,
* 10 = Pull-down resistor connected * 10 = Pull-down resistor connected
* x1 = No pull up resistor * x1 = No pull up resistor
*/ */
extern int s3c_gpio_setpull_s3c2443(struct s3c_gpio_chip *chip, extern int s3c2443_gpio_setpull(struct samsung_gpio_chip *chip,
unsigned int off, s3c_gpio_pull_t pull); unsigned int off, samsung_gpio_pull_t pull);
/** /**
* s3c_gpio_getpull_s3c2443() - Get configuration for s3c2443 pull resistors * s3c2443_gpio_getpull() - Get configuration for s3c2443 pull resistors
* @chip: The gpio chip that the GPIO pin belongs to. * @chip: The gpio chip that the GPIO pin belongs to.
* @off: The offset to the pin to get the configuration of. * @off: The offset to the pin to get the configuration of.
* *
* This helper function reads the state of the pull-{up,down} resistor for the * This helper function reads the state of the pull-{up,down} resistor for the
* given GPIO in the same case as s3c_gpio_setpull_upown. * given GPIO in the same case as samsung_gpio_setpull_upown.
*/ */
extern s3c_gpio_pull_t s3c_gpio_getpull_s3c2443(struct s3c_gpio_chip *chip, extern samsung_gpio_pull_t s3c2443_gpio_getpull(struct samsung_gpio_chip *chip,
unsigned int off); unsigned int off);
#endif /* __PLAT_GPIO_CFG_HELPERS_H */ #endif /* __PLAT_GPIO_CFG_HELPERS_H */
arch/arm/plat-samsung/include/plat/gpio-cfg.h
浏览文件 @ 782d8a3c
...@@ -24,14 +24,14 @@ ...@@ -24,14 +24,14 @@
#ifndef __PLAT_GPIO_CFG_H #ifndef __PLAT_GPIO_CFG_H
#define __PLAT_GPIO_CFG_H __FILE__ #define __PLAT_GPIO_CFG_H __FILE__
typedef unsigned int __bitwise__ s3c_gpio_pull_t; typedef unsigned int __bitwise__ samsung_gpio_pull_t;
typedef unsigned int __bitwise__ s5p_gpio_drvstr_t; typedef unsigned int __bitwise__ s5p_gpio_drvstr_t;
/* forward declaration if gpio-core.h hasn't been included */ /* forward declaration if gpio-core.h hasn't been included */
struct s3c_gpio_chip; struct samsung_gpio_chip;
/** /**
* struct s3c_gpio_cfg GPIO configuration * struct samsung_gpio_cfg GPIO configuration
* @cfg_eint: Configuration setting when used for external interrupt source * @cfg_eint: Configuration setting when used for external interrupt source
* @get_pull: Read the current pull configuration for the GPIO * @get_pull: Read the current pull configuration for the GPIO
* @set_pull: Set the current pull configuraiton for the GPIO * @set_pull: Set the current pull configuraiton for the GPIO
...@@ -44,20 +44,20 @@ struct s3c_gpio_chip; ...@@ -44,20 +44,20 @@ struct s3c_gpio_chip;
* per-bank configuration information that other systems such as the * per-bank configuration information that other systems such as the
* external interrupt code will need. * external interrupt code will need.
* *
* @sa s3c_gpio_cfgpin * @sa samsung_gpio_cfgpin
* @sa s3c_gpio_getcfg * @sa s3c_gpio_getcfg
* @sa s3c_gpio_setpull * @sa s3c_gpio_setpull
* @sa s3c_gpio_getpull * @sa s3c_gpio_getpull
*/ */
struct s3c_gpio_cfg { struct samsung_gpio_cfg {
unsigned int cfg_eint; unsigned int cfg_eint;
s3c_gpio_pull_t (*get_pull)(struct s3c_gpio_chip *chip, unsigned offs); samsung_gpio_pull_t (*get_pull)(struct samsung_gpio_chip *chip, unsigned offs);
int (*set_pull)(struct s3c_gpio_chip *chip, unsigned offs, int (*set_pull)(struct samsung_gpio_chip *chip, unsigned offs,
s3c_gpio_pull_t pull); samsung_gpio_pull_t pull);
unsigned (*get_config)(struct s3c_gpio_chip *chip, unsigned offs); unsigned (*get_config)(struct samsung_gpio_chip *chip, unsigned offs);
int (*set_config)(struct s3c_gpio_chip *chip, unsigned offs, int (*set_config)(struct samsung_gpio_chip *chip, unsigned offs,
unsigned config); unsigned config);
}; };
...@@ -69,7 +69,7 @@ struct s3c_gpio_cfg { ...@@ -69,7 +69,7 @@ struct s3c_gpio_cfg {
#define S3C_GPIO_OUTPUT (S3C_GPIO_SPECIAL(1)) #define S3C_GPIO_OUTPUT (S3C_GPIO_SPECIAL(1))
#define S3C_GPIO_SFN(x) (S3C_GPIO_SPECIAL(x)) #define S3C_GPIO_SFN(x) (S3C_GPIO_SPECIAL(x))
#define s3c_gpio_is_cfg_special(_cfg) \ #define samsung_gpio_is_cfg_special(_cfg) \
(((_cfg) & S3C_GPIO_SPECIAL_MARK) == S3C_GPIO_SPECIAL_MARK) (((_cfg) & S3C_GPIO_SPECIAL_MARK) == S3C_GPIO_SPECIAL_MARK)
/** /**
...@@ -128,9 +128,9 @@ extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr, ...@@ -128,9 +128,9 @@ extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr,
* up or down settings, and it may be dependent on the chip that is being * up or down settings, and it may be dependent on the chip that is being
* used to whether the particular mode is available. * used to whether the particular mode is available.
*/ */
#define S3C_GPIO_PULL_NONE ((__force s3c_gpio_pull_t)0x00) #define S3C_GPIO_PULL_NONE ((__force samsung_gpio_pull_t)0x00)
#define S3C_GPIO_PULL_DOWN ((__force s3c_gpio_pull_t)0x01) #define S3C_GPIO_PULL_DOWN ((__force samsung_gpio_pull_t)0x01)
#define S3C_GPIO_PULL_UP ((__force s3c_gpio_pull_t)0x02) #define S3C_GPIO_PULL_UP ((__force samsung_gpio_pull_t)0x02)
/** /**
* s3c_gpio_setpull() - set the state of a gpio pin pull resistor * s3c_gpio_setpull() - set the state of a gpio pin pull resistor
...@@ -143,7 +143,7 @@ extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr, ...@@ -143,7 +143,7 @@ extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr,
* *
* @pull is one of S3C_GPIO_PULL_NONE, S3C_GPIO_PULL_DOWN or S3C_GPIO_PULL_UP. * @pull is one of S3C_GPIO_PULL_NONE, S3C_GPIO_PULL_DOWN or S3C_GPIO_PULL_UP.
*/ */
extern int s3c_gpio_setpull(unsigned int pin, s3c_gpio_pull_t pull); extern int s3c_gpio_setpull(unsigned int pin, samsung_gpio_pull_t pull);
/** /**
* s3c_gpio_getpull() - get the pull resistor state of a gpio pin * s3c_gpio_getpull() - get the pull resistor state of a gpio pin
...@@ -151,7 +151,7 @@ extern int s3c_gpio_setpull(unsigned int pin, s3c_gpio_pull_t pull); ...@@ -151,7 +151,7 @@ extern int s3c_gpio_setpull(unsigned int pin, s3c_gpio_pull_t pull);
* *
* Read the pull resistor value for the specified pin. * Read the pull resistor value for the specified pin.
*/ */
extern s3c_gpio_pull_t s3c_gpio_getpull(unsigned int pin); extern samsung_gpio_pull_t s3c_gpio_getpull(unsigned int pin);
/* configure `all` aspects of an gpio */ /* configure `all` aspects of an gpio */
...@@ -170,7 +170,7 @@ extern s3c_gpio_pull_t s3c_gpio_getpull(unsigned int pin); ...@@ -170,7 +170,7 @@ extern s3c_gpio_pull_t s3c_gpio_getpull(unsigned int pin);
* @sa s3c_gpio_cfgpin_range * @sa s3c_gpio_cfgpin_range
*/ */
extern int s3c_gpio_cfgall_range(unsigned int start, unsigned int nr, extern int s3c_gpio_cfgall_range(unsigned int start, unsigned int nr,
unsigned int cfg, s3c_gpio_pull_t pull); unsigned int cfg, samsung_gpio_pull_t pull);
static inline int s3c_gpio_cfgrange_nopull(unsigned int pin, unsigned int size, static inline int s3c_gpio_cfgrange_nopull(unsigned int pin, unsigned int size,
unsigned int cfg) unsigned int cfg)
......
arch/arm/plat-samsung/include/plat/gpio-core.h
浏览文件 @ 782d8a3c
...@@ -25,22 +25,22 @@ ...@@ -25,22 +25,22 @@
* specific code. * specific code.
*/ */
struct s3c_gpio_chip; struct samsung_gpio_chip;
/** /**
* struct s3c_gpio_pm - power management (suspend/resume) information * struct samsung_gpio_pm - power management (suspend/resume) information
* @save: Routine to save the state of the GPIO block * @save: Routine to save the state of the GPIO block
* @resume: Routine to resume the GPIO block. * @resume: Routine to resume the GPIO block.
*/ */
struct s3c_gpio_pm { struct samsung_gpio_pm {
void (*save)(struct s3c_gpio_chip *chip); void (*save)(struct samsung_gpio_chip *chip);
void (*resume)(struct s3c_gpio_chip *chip); void (*resume)(struct samsung_gpio_chip *chip);
}; };
struct s3c_gpio_cfg; struct samsung_gpio_cfg;
/** /**
* struct s3c_gpio_chip - wrapper for specific implementation of gpio * struct samsung_gpio_chip - wrapper for specific implementation of gpio
* @chip: The chip structure to be exported via gpiolib. * @chip: The chip structure to be exported via gpiolib.
* @base: The base pointer to the gpio configuration registers. * @base: The base pointer to the gpio configuration registers.
* @group: The group register number for gpio interrupt support. * @group: The group register number for gpio interrupt support.
...@@ -60,10 +60,10 @@ struct s3c_gpio_cfg; ...@@ -60,10 +60,10 @@ struct s3c_gpio_cfg;
* CPU cores trying to get one lock for different GPIO banks, where each * CPU cores trying to get one lock for different GPIO banks, where each
* bank of GPIO has its own register space and configuration registers. * bank of GPIO has its own register space and configuration registers.
*/ */
struct s3c_gpio_chip { struct samsung_gpio_chip {
struct gpio_chip chip; struct gpio_chip chip;
struct s3c_gpio_cfg *config; struct samsung_gpio_cfg *config;
struct s3c_gpio_pm *pm; struct samsung_gpio_pm *pm;
void __iomem *base; void __iomem *base;
int irq_base; int irq_base;
int group; int group;
...@@ -73,58 +73,11 @@ struct s3c_gpio_chip { ...@@ -73,58 +73,11 @@ struct s3c_gpio_chip {
#endif #endif
}; };
static inline struct s3c_gpio_chip *to_s3c_gpio(struct gpio_chip *gpc) static inline struct samsung_gpio_chip *to_samsung_gpio(struct gpio_chip *gpc)
{ {
return container_of(gpc, struct s3c_gpio_chip, chip); return container_of(gpc, struct samsung_gpio_chip, chip);
} }
/** s3c_gpiolib_add() - add the s3c specific version of a gpio_chip.
* @chip: The chip to register
*
* This is a wrapper to gpiochip_add() that takes our specific gpio chip
* information and makes the necessary alterations for the platform and
* notes the information for use with the configuration systems and any
* other parts of the system.
*/
extern void s3c_gpiolib_add(struct s3c_gpio_chip *chip);
/* CONFIG_S3C_GPIO_TRACK enables the tracking of the s3c specific gpios
* for use with the configuration calls, and other parts of the s3c gpiolib
* support code.
*
* Not all s3c support code will need this, as some configurations of cpu
* may only support one or two different configuration options and have an
* easy gpio to s3c_gpio_chip mapping function. If this is the case, then
* the machine support file should provide its own s3c_gpiolib_getchip()
* and any other necessary functions.
*/
/**
* samsung_gpiolib_add_4bit_chips - 4bit single register GPIO config.
* @chip: The gpio chip that is being configured.
* @nr_chips: The no of chips (gpio ports) for the GPIO being configured.
*
* This helper deal with the GPIO cases where the control register has 4 bits
* of control per GPIO, generally in the form of:
* 0000 = Input
* 0001 = Output
* others = Special functions (dependent on bank)
*
* Note, since the code to deal with the case where there are two control
* registers instead of one, we do not have a separate set of function
* (samsung_gpiolib_add_4bit2_chips)for each case.
*/
extern void samsung_gpiolib_add_4bit_chips(struct s3c_gpio_chip *chip,
int nr_chips);
extern void samsung_gpiolib_add_4bit2_chips(struct s3c_gpio_chip *chip,
int nr_chips);
extern void samsung_gpiolib_add_2bit_chips(struct s3c_gpio_chip *chip,
int nr_chips);
extern void samsung_gpiolib_add_4bit(struct s3c_gpio_chip *chip);
extern void samsung_gpiolib_add_4bit2(struct s3c_gpio_chip *chip);
/** /**
* samsung_gpiolib_to_irq - convert gpio pin to irq number * samsung_gpiolib_to_irq - convert gpio pin to irq number
* @chip: The gpio chip that the pin belongs to. * @chip: The gpio chip that the pin belongs to.
...@@ -136,36 +89,36 @@ extern void samsung_gpiolib_add_4bit2(struct s3c_gpio_chip *chip); ...@@ -136,36 +89,36 @@ extern void samsung_gpiolib_add_4bit2(struct s3c_gpio_chip *chip);
extern int samsung_gpiolib_to_irq(struct gpio_chip *chip, unsigned int offset); extern int samsung_gpiolib_to_irq(struct gpio_chip *chip, unsigned int offset);
/* exported for core SoC support to change */ /* exported for core SoC support to change */
extern struct s3c_gpio_cfg s3c24xx_gpiocfg_default; extern struct samsung_gpio_cfg s3c24xx_gpiocfg_default;
#ifdef CONFIG_S3C_GPIO_TRACK #ifdef CONFIG_S3C_GPIO_TRACK
extern struct s3c_gpio_chip *s3c_gpios[S3C_GPIO_END]; extern struct samsung_gpio_chip *s3c_gpios[S3C_GPIO_END];
static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int chip) static inline struct samsung_gpio_chip *samsung_gpiolib_getchip(unsigned int chip)
{ {
return (chip < S3C_GPIO_END) ? s3c_gpios[chip] : NULL; return (chip < S3C_GPIO_END) ? s3c_gpios[chip] : NULL;
} }
#else #else
/* machine specific code should provide s3c_gpiolib_getchip */ /* machine specific code should provide samsung_gpiolib_getchip */
#include <mach/gpio-track.h> #include <mach/gpio-track.h>
static inline void s3c_gpiolib_track(struct s3c_gpio_chip *chip) { } static inline void s3c_gpiolib_track(struct samsung_gpio_chip *chip) { }
#endif #endif
#ifdef CONFIG_PM #ifdef CONFIG_PM
extern struct s3c_gpio_pm s3c_gpio_pm_1bit; extern struct samsung_gpio_pm samsung_gpio_pm_1bit;
extern struct s3c_gpio_pm s3c_gpio_pm_2bit; extern struct samsung_gpio_pm samsung_gpio_pm_2bit;
extern struct s3c_gpio_pm s3c_gpio_pm_4bit; extern struct samsung_gpio_pm samsung_gpio_pm_4bit;
#define __gpio_pm(x) x #define __gpio_pm(x) x
#else #else
#define s3c_gpio_pm_1bit NULL #define samsung_gpio_pm_1bit NULL
#define s3c_gpio_pm_2bit NULL #define samsung_gpio_pm_2bit NULL
#define s3c_gpio_pm_4bit NULL #define samsung_gpio_pm_4bit NULL
#define __gpio_pm(x) NULL #define __gpio_pm(x) NULL
#endif /* CONFIG_PM */ #endif /* CONFIG_PM */
/* locking wrappers to deal with multiple access to the same gpio bank */ /* locking wrappers to deal with multiple access to the same gpio bank */
#define s3c_gpio_lock(_oc, _fl) spin_lock_irqsave(&(_oc)->lock, _fl) #define samsung_gpio_lock(_oc, _fl) spin_lock_irqsave(&(_oc)->lock, _fl)
#define s3c_gpio_unlock(_oc, _fl) spin_unlock_irqrestore(&(_oc)->lock, _fl) #define samsung_gpio_unlock(_oc, _fl) spin_unlock_irqrestore(&(_oc)->lock, _fl)
arch/arm/plat-samsung/include/plat/gpio-fns.h 0 → 100644
浏览文件 @ 782d8a3c
/* arch/arm/mach-s3c2410/include/mach/gpio-fns.h
*
* Copyright (c) 2003-2009 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - hardware
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef __MACH_GPIO_FNS_H
#define __MACH_GPIO_FNS_H __FILE__
/* These functions are in the to-be-removed category and it is strongly
* encouraged not to use these in new code. They will be marked deprecated
* very soon.
*
* Most of the functionality can be either replaced by the gpiocfg calls
* for the s3c platform or by the generic GPIOlib API.
*
* As of 2.6.35-rc, these will be removed, with the few drivers using them
* either replaced or given a wrapper until the calls can be removed.
*/
#include <plat/gpio-cfg.h>
static inline void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int cfg)
{
/* 1:1 mapping between cfgpin and setcfg calls at the moment */
s3c_gpio_cfgpin(pin, cfg);
}
/* external functions for GPIO support
*
* These allow various different clients to access the same GPIO
* registers without conflicting. If your driver only owns the entire
* GPIO register, then it is safe to ioremap/__raw_{read|write} to it.
*/
extern unsigned int s3c2410_gpio_getcfg(unsigned int pin);
/* s3c2410_gpio_getirq
*
* turn the given pin number into the corresponding IRQ number
*
* returns:
* < 0 = no interrupt for this pin
* >=0 = interrupt number for the pin
*/
extern int s3c2410_gpio_getirq(unsigned int pin);
/* s3c2410_gpio_irqfilter
*
* set the irq filtering on the given pin
*
* on = 0 => disable filtering
* 1 => enable filtering
*
* config = S3C2410_EINTFLT_PCLK or S3C2410_EINTFLT_EXTCLK orred with
* width of filter (0 through 63)
*
*
*/
extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
unsigned int config);
/* s3c2410_gpio_pullup
*
* This call should be replaced with s3c_gpio_setpull().
*
* As a note, there is currently no distinction between pull-up and pull-down
* in the s3c24xx series devices with only an on/off configuration.
*/
/* s3c2410_gpio_pullup
*
* configure the pull-up control on the given pin
*
* to = 1 => disable the pull-up
* 0 => enable the pull-up
*
* eg;
*
* s3c2410_gpio_pullup(S3C2410_GPB(0), 0);
* s3c2410_gpio_pullup(S3C2410_GPE(8), 0);
*/
extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to);
extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
extern unsigned int s3c2410_gpio_getpin(unsigned int pin);
#endif /* __MACH_GPIO_FNS_H */
arch/arm/plat-samsung/include/plat/pm.h
浏览文件 @ 782d8a3c
...@@ -165,20 +165,20 @@ extern void s3c_pm_check_store(void); ...@@ -165,20 +165,20 @@ extern void s3c_pm_check_store(void);
extern void s3c_pm_configure_extint(void); extern void s3c_pm_configure_extint(void);
/** /**
* s3c_pm_restore_gpios() - restore the state of the gpios after sleep. * samsung_pm_restore_gpios() - restore the state of the gpios after sleep.
* *
* Restore the state of the GPIO pins after sleep, which may involve ensuring * Restore the state of the GPIO pins after sleep, which may involve ensuring
* that we do not glitch the state of the pins from that the bootloader's * that we do not glitch the state of the pins from that the bootloader's
* resume code has done. * resume code has done.
*/ */
extern void s3c_pm_restore_gpios(void); extern void samsung_pm_restore_gpios(void);
/** /**
* s3c_pm_save_gpios() - save the state of the GPIOs for restoring after sleep. * samsung_pm_save_gpios() - save the state of the GPIOs for restoring after sleep.
* *
* Save the GPIO states for resotration on resume. See s3c_pm_restore_gpios(). * Save the GPIO states for resotration on resume. See samsung_pm_restore_gpios().
*/ */
extern void s3c_pm_save_gpios(void); extern void samsung_pm_save_gpios(void);
extern void s3c_pm_save_core(void); extern void s3c_pm_save_core(void);
extern void s3c_pm_restore_core(void); extern void s3c_pm_restore_core(void);
arch/arm/plat-samsung/pm-gpio.c
浏览文件 @ 782d8a3c
...@@ -28,13 +28,13 @@ ...@@ -28,13 +28,13 @@
#define OFFS_DAT (0x04) #define OFFS_DAT (0x04)
#define OFFS_UP (0x08) #define OFFS_UP (0x08)
static void s3c_gpio_pm_1bit_save(struct s3c_gpio_chip *chip) static void samsung_gpio_pm_1bit_save(struct samsung_gpio_chip *chip)
{ {
chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON); chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON);
chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT); chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT);
} }
static void s3c_gpio_pm_1bit_resume(struct s3c_gpio_chip *chip) static void samsung_gpio_pm_1bit_resume(struct samsung_gpio_chip *chip)
{ {
void __iomem *base = chip->base; void __iomem *base = chip->base;
u32 old_gpcon = __raw_readl(base + OFFS_CON); u32 old_gpcon = __raw_readl(base + OFFS_CON);
...@@ -60,12 +60,12 @@ static void s3c_gpio_pm_1bit_resume(struct s3c_gpio_chip *chip) ...@@ -60,12 +60,12 @@ static void s3c_gpio_pm_1bit_resume(struct s3c_gpio_chip *chip)
chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat); chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
} }
struct s3c_gpio_pm s3c_gpio_pm_1bit = { struct samsung_gpio_pm samsung_gpio_pm_1bit = {
.save = s3c_gpio_pm_1bit_save, .save = samsung_gpio_pm_1bit_save,
.resume = s3c_gpio_pm_1bit_resume, .resume = samsung_gpio_pm_1bit_resume,
}; };
static void s3c_gpio_pm_2bit_save(struct s3c_gpio_chip *chip) static void samsung_gpio_pm_2bit_save(struct samsung_gpio_chip *chip)
{ {
chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON); chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON);
chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT); chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT);
...@@ -95,7 +95,7 @@ static inline int is_out(unsigned long con) ...@@ -95,7 +95,7 @@ static inline int is_out(unsigned long con)
} }
/** /**
* s3c_gpio_pm_2bit_resume() - restore the given GPIO bank * samsung_gpio_pm_2bit_resume() - restore the given GPIO bank
* @chip: The chip information to resume. * @chip: The chip information to resume.
* *
* Restore one of the GPIO banks that was saved during suspend. This is * Restore one of the GPIO banks that was saved during suspend. This is
...@@ -121,7 +121,7 @@ static inline int is_out(unsigned long con) ...@@ -121,7 +121,7 @@ static inline int is_out(unsigned long con)
* [1] this assumes that writing to a pin DAT whilst in SFN will set the * [1] this assumes that writing to a pin DAT whilst in SFN will set the
* state for when it is next output. * state for when it is next output.
*/ */
static void s3c_gpio_pm_2bit_resume(struct s3c_gpio_chip *chip) static void samsung_gpio_pm_2bit_resume(struct samsung_gpio_chip *chip)
{ {
void __iomem *base = chip->base; void __iomem *base = chip->base;
u32 old_gpcon = __raw_readl(base + OFFS_CON); u32 old_gpcon = __raw_readl(base + OFFS_CON);
...@@ -187,13 +187,13 @@ static void s3c_gpio_pm_2bit_resume(struct s3c_gpio_chip *chip) ...@@ -187,13 +187,13 @@ static void s3c_gpio_pm_2bit_resume(struct s3c_gpio_chip *chip)
chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat); chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
} }
struct s3c_gpio_pm s3c_gpio_pm_2bit = { struct samsung_gpio_pm samsung_gpio_pm_2bit = {
.save = s3c_gpio_pm_2bit_save, .save = samsung_gpio_pm_2bit_save,
.resume = s3c_gpio_pm_2bit_resume, .resume = samsung_gpio_pm_2bit_resume,
}; };
#if defined(CONFIG_ARCH_S3C64XX) || defined(CONFIG_PLAT_S5P) #if defined(CONFIG_ARCH_S3C64XX) || defined(CONFIG_PLAT_S5P)
static void s3c_gpio_pm_4bit_save(struct s3c_gpio_chip *chip) static void samsung_gpio_pm_4bit_save(struct samsung_gpio_chip *chip)
{ {
chip->pm_save[1] = __raw_readl(chip->base + OFFS_CON); chip->pm_save[1] = __raw_readl(chip->base + OFFS_CON);
chip->pm_save[2] = __raw_readl(chip->base + OFFS_DAT); chip->pm_save[2] = __raw_readl(chip->base + OFFS_DAT);
...@@ -203,7 +203,7 @@ static void s3c_gpio_pm_4bit_save(struct s3c_gpio_chip *chip) ...@@ -203,7 +203,7 @@ static void s3c_gpio_pm_4bit_save(struct s3c_gpio_chip *chip)
chip->pm_save[0] = __raw_readl(chip->base - 4); chip->pm_save[0] = __raw_readl(chip->base - 4);
} }
static u32 s3c_gpio_pm_4bit_mask(u32 old_gpcon, u32 gps_gpcon) static u32 samsung_gpio_pm_4bit_mask(u32 old_gpcon, u32 gps_gpcon)
{ {
u32 old, new, mask; u32 old, new, mask;
u32 change_mask = 0x0; u32 change_mask = 0x0;
...@@ -242,14 +242,14 @@ static u32 s3c_gpio_pm_4bit_mask(u32 old_gpcon, u32 gps_gpcon) ...@@ -242,14 +242,14 @@ static u32 s3c_gpio_pm_4bit_mask(u32 old_gpcon, u32 gps_gpcon)
return change_mask; return change_mask;
} }
static void s3c_gpio_pm_4bit_con(struct s3c_gpio_chip *chip, int index) static void samsung_gpio_pm_4bit_con(struct samsung_gpio_chip *chip, int index)
{ {
void __iomem *con = chip->base + (index * 4); void __iomem *con = chip->base + (index * 4);
u32 old_gpcon = __raw_readl(con); u32 old_gpcon = __raw_readl(con);
u32 gps_gpcon = chip->pm_save[index + 1]; u32 gps_gpcon = chip->pm_save[index + 1];
u32 gpcon, mask; u32 gpcon, mask;
mask = s3c_gpio_pm_4bit_mask(old_gpcon, gps_gpcon); mask = samsung_gpio_pm_4bit_mask(old_gpcon, gps_gpcon);
gpcon = old_gpcon & ~mask; gpcon = old_gpcon & ~mask;
gpcon |= gps_gpcon & mask; gpcon |= gps_gpcon & mask;
...@@ -257,7 +257,7 @@ static void s3c_gpio_pm_4bit_con(struct s3c_gpio_chip *chip, int index) ...@@ -257,7 +257,7 @@ static void s3c_gpio_pm_4bit_con(struct s3c_gpio_chip *chip, int index)
__raw_writel(gpcon, con); __raw_writel(gpcon, con);
} }
static void s3c_gpio_pm_4bit_resume(struct s3c_gpio_chip *chip) static void samsung_gpio_pm_4bit_resume(struct samsung_gpio_chip *chip)
{ {
void __iomem *base = chip->base; void __iomem *base = chip->base;
u32 old_gpcon[2]; u32 old_gpcon[2];
...@@ -269,10 +269,10 @@ static void s3c_gpio_pm_4bit_resume(struct s3c_gpio_chip *chip) ...@@ -269,10 +269,10 @@ static void s3c_gpio_pm_4bit_resume(struct s3c_gpio_chip *chip)
old_gpcon[0] = 0; old_gpcon[0] = 0;
old_gpcon[1] = __raw_readl(base + OFFS_CON); old_gpcon[1] = __raw_readl(base + OFFS_CON);
s3c_gpio_pm_4bit_con(chip, 0); samsung_gpio_pm_4bit_con(chip, 0);
if (chip->chip.ngpio > 8) { if (chip->chip.ngpio > 8) {
old_gpcon[0] = __raw_readl(base - 4); old_gpcon[0] = __raw_readl(base - 4);
s3c_gpio_pm_4bit_con(chip, -1); samsung_gpio_pm_4bit_con(chip, -1);
} }
/* Now change the configurations that require DAT,CON */ /* Now change the configurations that require DAT,CON */
...@@ -298,19 +298,19 @@ static void s3c_gpio_pm_4bit_resume(struct s3c_gpio_chip *chip) ...@@ -298,19 +298,19 @@ static void s3c_gpio_pm_4bit_resume(struct s3c_gpio_chip *chip)
old_gpdat, gps_gpdat); old_gpdat, gps_gpdat);
} }
struct s3c_gpio_pm s3c_gpio_pm_4bit = { struct samsung_gpio_pm samsung_gpio_pm_4bit = {
.save = s3c_gpio_pm_4bit_save, .save = samsung_gpio_pm_4bit_save,
.resume = s3c_gpio_pm_4bit_resume, .resume = samsung_gpio_pm_4bit_resume,
}; };
#endif /* CONFIG_ARCH_S3C64XX || CONFIG_PLAT_S5P */ #endif /* CONFIG_ARCH_S3C64XX || CONFIG_PLAT_S5P */
/** /**
* s3c_pm_save_gpio() - save gpio chip data for suspend * samsung_pm_save_gpio() - save gpio chip data for suspend
* @ourchip: The chip for suspend. * @ourchip: The chip for suspend.
*/ */
static void s3c_pm_save_gpio(struct s3c_gpio_chip *ourchip) static void samsung_pm_save_gpio(struct samsung_gpio_chip *ourchip)
{ {
struct s3c_gpio_pm *pm = ourchip->pm; struct samsung_gpio_pm *pm = ourchip->pm;
if (pm == NULL || pm->save == NULL) if (pm == NULL || pm->save == NULL)
S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label); S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label);
...@@ -319,24 +319,24 @@ static void s3c_pm_save_gpio(struct s3c_gpio_chip *ourchip) ...@@ -319,24 +319,24 @@ static void s3c_pm_save_gpio(struct s3c_gpio_chip *ourchip)
} }
/** /**
* s3c_pm_save_gpios() - Save the state of the GPIO banks. * samsung_pm_save_gpios() - Save the state of the GPIO banks.
* *
* For all the GPIO banks, save the state of each one ready for going * For all the GPIO banks, save the state of each one ready for going
* into a suspend mode. * into a suspend mode.
*/ */
void s3c_pm_save_gpios(void) void samsung_pm_save_gpios(void)
{ {
struct s3c_gpio_chip *ourchip; struct samsung_gpio_chip *ourchip;
unsigned int gpio_nr; unsigned int gpio_nr;
for (gpio_nr = 0; gpio_nr < S3C_GPIO_END;) { for (gpio_nr = 0; gpio_nr < S3C_GPIO_END;) {
ourchip = s3c_gpiolib_getchip(gpio_nr); ourchip = samsung_gpiolib_getchip(gpio_nr);
if (!ourchip) { if (!ourchip) {
gpio_nr++; gpio_nr++;
continue; continue;
} }
s3c_pm_save_gpio(ourchip); samsung_pm_save_gpio(ourchip);
S3C_PMDBG("%s: save %08x,%08x,%08x,%08x\n", S3C_PMDBG("%s: save %08x,%08x,%08x,%08x\n",
ourchip->chip.label, ourchip->chip.label,
...@@ -351,12 +351,12 @@ void s3c_pm_save_gpios(void) ...@@ -351,12 +351,12 @@ void s3c_pm_save_gpios(void)
} }
/** /**
* s3c_pm_resume_gpio() - restore gpio chip data after suspend * samsung_pm_resume_gpio() - restore gpio chip data after suspend
* @ourchip: The suspended chip. * @ourchip: The suspended chip.
*/ */
static void s3c_pm_resume_gpio(struct s3c_gpio_chip *ourchip) static void samsung_pm_resume_gpio(struct samsung_gpio_chip *ourchip)
{ {
struct s3c_gpio_pm *pm = ourchip->pm; struct samsung_gpio_pm *pm = ourchip->pm;
if (pm == NULL || pm->resume == NULL) if (pm == NULL || pm->resume == NULL)
S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label); S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label);
...@@ -364,19 +364,19 @@ static void s3c_pm_resume_gpio(struct s3c_gpio_chip *ourchip) ...@@ -364,19 +364,19 @@ static void s3c_pm_resume_gpio(struct s3c_gpio_chip *ourchip)
pm->resume(ourchip); pm->resume(ourchip);
} }
void s3c_pm_restore_gpios(void) void samsung_pm_restore_gpios(void)
{ {
struct s3c_gpio_chip *ourchip; struct samsung_gpio_chip *ourchip;
unsigned int gpio_nr; unsigned int gpio_nr;
for (gpio_nr = 0; gpio_nr < S3C_GPIO_END;) { for (gpio_nr = 0; gpio_nr < S3C_GPIO_END;) {
ourchip = s3c_gpiolib_getchip(gpio_nr); ourchip = samsung_gpiolib_getchip(gpio_nr);
if (!ourchip) { if (!ourchip) {
gpio_nr++; gpio_nr++;
continue; continue;
} }
s3c_pm_resume_gpio(ourchip); samsung_pm_resume_gpio(ourchip);
gpio_nr += ourchip->chip.ngpio; gpio_nr += ourchip->chip.ngpio;
gpio_nr += CONFIG_S3C_GPIO_SPACE; gpio_nr += CONFIG_S3C_GPIO_SPACE;
......
arch/arm/plat-samsung/pm.c
浏览文件 @ 782d8a3c
...@@ -268,8 +268,8 @@ static int s3c_pm_enter(suspend_state_t state) ...@@ -268,8 +268,8 @@ static int s3c_pm_enter(suspend_state_t state)
/* save all necessary core registers not covered by the drivers */ /* save all necessary core registers not covered by the drivers */
s3c_pm_save_gpios(); samsung_pm_save_gpios();
s3c_pm_saved_gpios(); samsung_pm_saved_gpios();
s3c_pm_save_uarts(); s3c_pm_save_uarts();
s3c_pm_save_core(); s3c_pm_save_core();
...@@ -306,7 +306,7 @@ static int s3c_pm_enter(suspend_state_t state) ...@@ -306,7 +306,7 @@ static int s3c_pm_enter(suspend_state_t state)
s3c_pm_restore_core(); s3c_pm_restore_core();
s3c_pm_restore_uarts(); s3c_pm_restore_uarts();
s3c_pm_restore_gpios(); samsung_pm_restore_gpios();
s3c_pm_restored_gpios(); s3c_pm_restored_gpios();
s3c_pm_debug_init(); s3c_pm_debug_init();
......
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或