Merge branch 'nomadik' into devel-stable

arch/arm/Kconfig

@@ -338,6 +338,20 @@ config ARCH_H720X
 	help
 	  This enables support for systems based on the Hynix HMS720x
 
+config ARCH_NOMADIK
+	bool "STMicroelectronics Nomadik"
+	select ARM_AMBA
+	select ARM_VIC
+	select CPU_ARM926T
+	select HAVE_CLK
+	select COMMON_CLKDEV
+	select GENERIC_TIME
+	select GENERIC_CLOCKEVENTS
+	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
+	help
+	  Support for the Nomadik platform by ST-Ericsson
+
 config ARCH_IOP13XX
 	bool "IOP13xx-based"
 	depends on MMU
@@ -745,6 +759,8 @@ source "arch/arm/mach-at91/Kconfig"
 
 source "arch/arm/plat-mxc/Kconfig"
 
+source "arch/arm/mach-nomadik/Kconfig"
+
 source "arch/arm/mach-netx/Kconfig"
 
 source "arch/arm/mach-ns9xxx/Kconfig"

arch/arm/Makefile

@@ -145,6 +145,7 @@ machine-$(CONFIG_ARCH_MX2)		:= mx2
 machine-$(CONFIG_ARCH_MX25)		:= mx25
 machine-$(CONFIG_ARCH_MX3)		:= mx3
 machine-$(CONFIG_ARCH_NETX)		:= netx
+machine-$(CONFIG_ARCH_NOMADIK)		:= nomadik
 machine-$(CONFIG_ARCH_NS9XXX)		:= ns9xxx
 machine-$(CONFIG_ARCH_OMAP1)		:= omap1
 machine-$(CONFIG_ARCH_OMAP2)		:= omap2

arch/arm/common/vic.c

@@ -26,6 +26,15 @@
 #include <asm/mach/irq.h>
 #include <asm/hardware/vic.h>
 
+static void vic_ack_irq(unsigned int irq)
+{
+	void __iomem *base = get_irq_chip_data(irq);
+	irq &= 31;
+	writel(1 << irq, base + VIC_INT_ENABLE_CLEAR);
+	/* moreover, clear the soft-triggered, in case it was the reason */
+	writel(1 << irq, base + VIC_INT_SOFT_CLEAR);
+}
+
 static void vic_mask_irq(unsigned int irq)
 {
 	void __iomem *base = get_irq_chip_data(irq);
@@ -253,12 +262,21 @@ static inline void vic_pm_register(void __iomem *base, unsigned int irq, u32 arg
 
 static struct irq_chip vic_chip = {
 	.name	= "VIC",
-	.ack	= vic_mask_irq,
+	.ack	= vic_ack_irq,
 	.mask	= vic_mask_irq,
 	.unmask	= vic_unmask_irq,
 	.set_wake = vic_set_wake,
 };
 
+/* The PL190 cell from ARM has been modified by ST, so handle both here */
+static void vik_init_st(void __iomem *base, unsigned int irq_start,
+			 u32 vic_sources);
+
+enum vic_vendor {
+	VENDOR_ARM = 0x41,
+	VENDOR_ST = 0x80,
+};
+
 /**
  * vic_init - initialise a vectored interrupt controller
  * @base: iomem base address
@@ -270,6 +288,28 @@ void __init vic_init(void __iomem *base, unsigned int irq_start,
 		     u32 vic_sources, u32 resume_sources)
 {
 	unsigned int i;
+	u32 cellid = 0;
+	enum vic_vendor vendor;
+
+	/* Identify which VIC cell this one is, by reading the ID */
+	for (i = 0; i < 4; i++) {
+		u32 addr = ((u32)base & PAGE_MASK) + 0xfe0 + (i * 4);
+		cellid |= (readl(addr) & 0xff) << (8 * i);
+	}
+	vendor = (cellid >> 12) & 0xff;
+	printk(KERN_INFO "VIC @%p: id 0x%08x, vendor 0x%02x\n",
+	       base, cellid, vendor);
+
+	switch(vendor) {
+	case VENDOR_ST:
+		vik_init_st(base, irq_start, vic_sources);
+		return;
+	default:
+		printk(KERN_WARNING "VIC: unknown vendor, continuing anyways\n");
+		/* fall through */
+	case VENDOR_ARM:
+		break;
+	}
 
 	/* Disable all interrupts initially. */
 
@@ -306,3 +346,60 @@ void __init vic_init(void __iomem *base, unsigned int irq_start,
 
 	vic_pm_register(base, irq_start, resume_sources);
 }
+
+/*
+ * The PL190 cell from ARM has been modified by ST to handle 64 interrupts.
+ * The original cell has 32 interrupts, while the modified one has 64,
+ * replocating two blocks 0x00..0x1f in 0x20..0x3f. In that case
+ * the probe function is called twice, with base set to offset 000
+ *  and 020 within the page. We call this "second block".
+ */
+static void __init vik_init_st(void __iomem *base, unsigned int irq_start,
+				u32 vic_sources)
+{
+	unsigned int i;
+	int vic_2nd_block = ((unsigned long)base & ~PAGE_MASK) != 0;
+
+	/* Disable all interrupts initially. */
+
+	writel(0, base + VIC_INT_SELECT);
+	writel(0, base + VIC_INT_ENABLE);
+	writel(~0, base + VIC_INT_ENABLE_CLEAR);
+	writel(0, base + VIC_IRQ_STATUS);
+	writel(0, base + VIC_ITCR);
+	writel(~0, base + VIC_INT_SOFT_CLEAR);
+
+	/*
+	 * Make sure we clear all existing interrupts. The vector registers
+	 * in this cell are after the second block of general registers,
+	 * so we can address them using standard offsets, but only from
+	 * the second base address, which is 0x20 in the page
+	 */
+	if (vic_2nd_block) {
+		writel(0, base + VIC_PL190_VECT_ADDR);
+		for (i = 0; i < 19; i++) {
+			unsigned int value;
+
+			value = readl(base + VIC_PL190_VECT_ADDR);
+			writel(value, base + VIC_PL190_VECT_ADDR);
+		}
+		/* ST has 16 vectors as well, but we don't enable them by now */
+		for (i = 0; i < 16; i++) {
+			void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4);
+			writel(0, reg);
+		}
+
+		writel(32, base + VIC_PL190_DEF_VECT_ADDR);
+	}
+
+	for (i = 0; i < 32; i++) {
+		if (vic_sources & (1 << i)) {
+			unsigned int irq = irq_start + i;
+
+			set_irq_chip(irq, &vic_chip);
+			set_irq_chip_data(irq, base);
+			set_irq_handler(irq, handle_level_irq);
+			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		}
+	}
+}

arch/arm/mach-nomadik/Kconfig

+if ARCH_NOMADIK
+
+menu "Nomadik boards"
+
+config MACH_NOMADIK_8815NHK
+	bool "ST 8815 Nomadik Hardware Kit (evaluation board)"
+	select NOMADIK_8815
+
+endmenu
+
+config NOMADIK_8815
+	bool
+
+
+config I2C_BITBANG_8815NHK
+	tristate "Driver for bit-bang busses found on the 8815 NHK"
+	depends on I2C && MACH_NOMADIK_8815NHK
+	select I2C_ALGOBIT
+	default y
+
+endif

arch/arm/mach-nomadik/Makefile

+#
+# Makefile for the linux kernel.
+#
+# Note! Dependencies are done automagically by 'make dep', which also
+# removes any old dependencies. DON'T put your own dependencies here
+# unless it's something special (ie not a .c file).
+
+# Object file lists.
+
+obj-y			+= clock.o timer.o gpio.o
+
+# Cpu revision
+obj-$(CONFIG_NOMADIK_8815) += cpu-8815.o
+
+# Specific board support
+obj-$(CONFIG_MACH_NOMADIK_8815NHK) += board-nhk8815.o
+
+# Nomadik extra devices
+obj-$(CONFIG_I2C_BITBANG_8815NHK) += i2c-8815nhk.o

arch/arm/mach-nomadik/Makefile.boot

+   zreladdr-y	:= 0x00008000
+params_phys-y	:= 0x00000100
+initrd_phys-y	:= 0x00800000
+

arch/arm/mach-nomadik/board-nhk8815.c

+/*
+ *  linux/arch/arm/mach-nomadik/board-8815nhk.c
+ *
+ *  Copyright (C) STMicroelectronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ *  NHK15 board specifc driver definition
+ */
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/amba/bus.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/irq.h>
+#include <mach/setup.h>
+#include "clock.h"
+
+#define __MEM_4K_RESOURCE(x) \
+	.res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
+
+static struct amba_device uart0_device = {
+	.dev = { .init_name = "uart0" },
+	__MEM_4K_RESOURCE(NOMADIK_UART0_BASE),
+	.irq = {IRQ_UART0, NO_IRQ},
+};
+
+static struct amba_device uart1_device = {
+	.dev = { .init_name = "uart1" },
+	__MEM_4K_RESOURCE(NOMADIK_UART1_BASE),
+	.irq = {IRQ_UART1, NO_IRQ},
+};
+
+static struct amba_device *amba_devs[] __initdata = {
+	&uart0_device,
+	&uart1_device,
+};
+
+/* We have a fixed clock alone, by now */
+static struct clk nhk8815_clk_48 = {
+	.rate = 48*1000*1000,
+};
+
+static struct resource nhk8815_eth_resources[] = {
+	{
+		.name = "smc91x-regs",
+		.start = 0x34000000 + 0x300,
+		.end = 0x34000000 + SZ_64K - 1,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = NOMADIK_GPIO_TO_IRQ(115),
+		.end = NOMADIK_GPIO_TO_IRQ(115),
+		.flags = IORESOURCE_IRQ | IRQF_TRIGGER_RISING,
+	}
+};
+
+static struct platform_device nhk8815_eth_device = {
+	.name = "smc91x",
+	.resource = nhk8815_eth_resources,
+	.num_resources = ARRAY_SIZE(nhk8815_eth_resources),
+};
+
+static int __init nhk8815_eth_init(void)
+{
+	int gpio_nr = 115; /* hardwired in the board */
+	int err;
+
+	err = gpio_request(gpio_nr, "eth_irq");
+	if (!err) err = nmk_gpio_set_mode(gpio_nr, NMK_GPIO_ALT_GPIO);
+	if (!err) err = gpio_direction_input(gpio_nr);
+	if (err)
+		pr_err("Error %i in %s\n", err, __func__);
+	return err;
+}
+device_initcall(nhk8815_eth_init);
+
+static struct platform_device *nhk8815_platform_devices[] __initdata = {
+	&nhk8815_eth_device,
+	/* will add more devices */
+};
+
+static void __init nhk8815_platform_init(void)
+{
+	int i;
+
+	cpu8815_platform_init();
+	platform_add_devices(nhk8815_platform_devices,
+			     ARRAY_SIZE(nhk8815_platform_devices));
+
+	for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
+		nmdk_clk_create(&nhk8815_clk_48, amba_devs[i]->dev.init_name);
+		amba_device_register(amba_devs[i], &iomem_resource);
+	}
+}
+
+MACHINE_START(NOMADIK, "NHK8815")
+	/* Maintainer: ST MicroElectronics */
+	.phys_io	= NOMADIK_UART0_BASE,
+	.io_pg_offst	= (IO_ADDRESS(NOMADIK_UART0_BASE) >> 18) & 0xfffc,
+	.boot_params	= 0x100,
+	.map_io		= cpu8815_map_io,
+	.init_irq	= cpu8815_init_irq,
+	.timer		= &nomadik_timer,
+	.init_machine	= nhk8815_platform_init,
+MACHINE_END

arch/arm/mach-nomadik/clock.c

+/*
+ *  linux/arch/arm/mach-nomadik/clock.c
+ *
+ *  Copyright (C) 2009 Alessandro Rubini
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/clk.h>
+#include <asm/clkdev.h>
+#include "clock.h"
+
+/*
+ * The nomadik board uses generic clocks, but the serial pl011 file
+ * calls clk_enable(), clk_disable(), clk_get_rate(), so we provide them
+ */
+unsigned long clk_get_rate(struct clk *clk)
+{
+	return clk->rate;
+}
+EXPORT_SYMBOL(clk_get_rate);
+
+/* enable and disable do nothing */
+int clk_enable(struct clk *clk)
+{
+	return 0;
+}
+EXPORT_SYMBOL(clk_enable);
+
+void clk_disable(struct clk *clk)
+{
+}
+EXPORT_SYMBOL(clk_disable);
+
+/* Create a clock structure with the given name */
+int nmdk_clk_create(struct clk *clk, const char *dev_id)
+{
+	struct clk_lookup *clkdev;
+
+	clkdev = clkdev_alloc(clk, NULL, dev_id);
+	if (!clkdev)
+		return -ENOMEM;
+	clkdev_add(clkdev);
+	return 0;
+}

arch/arm/mach-nomadik/clock.h

+
+/*
+ *  linux/arch/arm/mach-nomadik/clock.h
+ *
+ *  Copyright (C) 2009 Alessandro Rubini
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+struct clk {
+	unsigned long		rate;
+};
+extern int nmdk_clk_create(struct clk *clk, const char *dev_id);

arch/arm/mach-nomadik/cpu-8815.c

+/*
+ * Copyright STMicroelectronics, 2007.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/amba/bus.h>
+#include <linux/gpio.h>
+
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <asm/mach/map.h>
+#include <asm/hardware/vic.h>
+
+#include <asm/cacheflush.h>
+#include <asm/hardware/cache-l2x0.h>
+
+/* The 8815 has 4 GPIO blocks, let's register them immediately */
+static struct nmk_gpio_platform_data cpu8815_gpio[] = {
+	{
+		.name = "GPIO-0-31",
+		.first_gpio = 0,
+		.first_irq = NOMADIK_GPIO_TO_IRQ(0),
+		.parent_irq = IRQ_GPIO0,
+	}, {
+		.name = "GPIO-32-63",
+		.first_gpio = 32,
+		.first_irq = NOMADIK_GPIO_TO_IRQ(32),
+		.parent_irq = IRQ_GPIO1,
+	}, {
+		.name = "GPIO-64-95",
+		.first_gpio = 64,
+		.first_irq = NOMADIK_GPIO_TO_IRQ(64),
+		.parent_irq = IRQ_GPIO2,
+	}, {
+		.name = "GPIO-96-127", /* 124..127 not routed to pin */
+		.first_gpio = 96,
+		.first_irq = NOMADIK_GPIO_TO_IRQ(96),
+		.parent_irq = IRQ_GPIO3,
+	}
+};
+
+#define __MEM_4K_RESOURCE(x) \
+	.res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
+
+static struct amba_device cpu8815_amba_gpio[] = {
+	{
+		.dev = {
+			.init_name = "gpio0",
+			.platform_data = cpu8815_gpio + 0,
+		},
+		__MEM_4K_RESOURCE(NOMADIK_GPIO0_BASE),
+	}, {
+		.dev = {
+			.init_name = "gpio1",
+			.platform_data = cpu8815_gpio + 1,
+		},
+		__MEM_4K_RESOURCE(NOMADIK_GPIO1_BASE),
+	}, {
+		.dev = {
+			.init_name = "gpio2",
+			.platform_data = cpu8815_gpio + 2,
+		},
+		__MEM_4K_RESOURCE(NOMADIK_GPIO2_BASE),
+	}, {
+		.dev = {
+			.init_name = "gpio3",
+			.platform_data = cpu8815_gpio + 3,
+		},
+		__MEM_4K_RESOURCE(NOMADIK_GPIO3_BASE),
+	},
+};
+
+static struct amba_device *amba_devs[] __initdata = {
+	cpu8815_amba_gpio + 0,
+	cpu8815_amba_gpio + 1,
+	cpu8815_amba_gpio + 2,
+	cpu8815_amba_gpio + 3,
+};
+
+static int __init cpu8815_init(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
+		amba_device_register(amba_devs[i], &iomem_resource);
+	return 0;
+}
+arch_initcall(cpu8815_init);
+
+/* All SoC devices live in the same area (see hardware.h) */
+static struct map_desc nomadik_io_desc[] __initdata = {
+	{
+		.virtual =	NOMADIK_IO_VIRTUAL,
+		.pfn =		__phys_to_pfn(NOMADIK_IO_PHYSICAL),
+		.length =	NOMADIK_IO_SIZE,
+		.type = 	MT_DEVICE,
+	}
+	/* static ram and secured ram may be added later */
+};
+
+void __init cpu8815_map_io(void)
+{
+	iotable_init(nomadik_io_desc, ARRAY_SIZE(nomadik_io_desc));
+}
+
+void __init cpu8815_init_irq(void)
+{
+	/* This modified VIC cell has two register blocks, at 0 and 0x20 */
+	vic_init(io_p2v(NOMADIK_IC_BASE + 0x00), IRQ_VIC_START +  0, ~0, 0);
+	vic_init(io_p2v(NOMADIK_IC_BASE + 0x20), IRQ_VIC_START + 32, ~0, 0);
+}
+
+/*
+ * This function is called from the board init ("init_machine").
+ */
+ void __init cpu8815_platform_init(void)
+{
+#ifdef CONFIG_CACHE_L2X0
+	/* At full speed latency must be >=2, so 0x249 in low bits */
+	l2x0_init(io_p2v(NOMADIK_L2CC_BASE), 0x00730249, 0xfe000fff);
+#endif
+	 return;
+}

arch/arm/mach-nomadik/gpio.c

+/*
+ * Generic GPIO driver for logic cells found in the Nomadik SoC
+ *
+ * Copyright (C) 2008,2009 STMicroelectronics
+ * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it>
+ *   Rewritten based on work by Prafulla WADASKAR <prafulla.wadaskar@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/amba/bus.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/gpio.h>
+
+/*
+ * The GPIO module in the Nomadik family of Systems-on-Chip is an
+ * AMBA device, managing 32 pins and alternate functions.  The logic block
+ * is currently only used in the Nomadik.
+ *
+ * Symbols in this file are called "nmk_gpio" for "nomadik gpio"
+ */
+
+#define NMK_GPIO_PER_CHIP 32
+struct nmk_gpio_chip {
+	struct gpio_chip chip;
+	void __iomem *addr;
+	unsigned int parent_irq;
+	spinlock_t *lock;
+	/* Keep track of configured edges */
+	u32 edge_rising;
+	u32 edge_falling;
+};
+
+/* Mode functions */
+int nmk_gpio_set_mode(int gpio, int gpio_mode)
+{
+	struct nmk_gpio_chip *nmk_chip;
+	unsigned long flags;
+	u32 afunc, bfunc, bit;
+
+	nmk_chip = get_irq_chip_data(NOMADIK_GPIO_TO_IRQ(gpio));
+	if (!nmk_chip)
+		return -EINVAL;
+
+	bit = 1 << (gpio - nmk_chip->chip.base);
+
+	spin_lock_irqsave(&nmk_chip->lock, flags);
+	afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & ~bit;
+	bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & ~bit;
+	if (gpio_mode & NMK_GPIO_ALT_A)
+		afunc |= bit;
+	if (gpio_mode & NMK_GPIO_ALT_B)
+		bfunc |= bit;
+	writel(afunc, nmk_chip->addr + NMK_GPIO_AFSLA);
+	writel(bfunc, nmk_chip->addr + NMK_GPIO_AFSLB);
+	spin_unlock_irqrestore(&nmk_chip->lock, flags);
+
+	return 0;
+}
+EXPORT_SYMBOL(nmk_gpio_set_mode);
+
+int nmk_gpio_get_mode(int gpio)
+{
+	struct nmk_gpio_chip *nmk_chip;
+	u32 afunc, bfunc, bit;
+
+	nmk_chip = get_irq_chip_data(NOMADIK_GPIO_TO_IRQ(gpio));
+	if (!nmk_chip)
+		return -EINVAL;
+
+	bit = 1 << (gpio - nmk_chip->chip.base);
+
+	afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & bit;
+	bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & bit;
+
+	return (afunc ? NMK_GPIO_ALT_A : 0) | (bfunc ? NMK_GPIO_ALT_B : 0);
+}
+EXPORT_SYMBOL(nmk_gpio_get_mode);
+
+
+/* IRQ functions */
+static inline int nmk_gpio_get_bitmask(int gpio)
+{
+	return 1 << (gpio % 32);
+}
+
+static void nmk_gpio_irq_ack(unsigned int irq)
+{
+	int gpio;
+	struct nmk_gpio_chip *nmk_chip;
+
+	gpio = NOMADIK_IRQ_TO_GPIO(irq);
+	nmk_chip = get_irq_chip_data(irq);
+	if (!nmk_chip)
+		return;
+	writel(nmk_gpio_get_bitmask(gpio), nmk_chip->addr + NMK_GPIO_IC);
+}
+
+static void nmk_gpio_irq_mask(unsigned int irq)
+{
+	int gpio;
+	struct nmk_gpio_chip *nmk_chip;
+	unsigned long flags;
+	u32 bitmask, reg;
+
+	gpio = NOMADIK_IRQ_TO_GPIO(irq);
+	nmk_chip = get_irq_chip_data(irq);
+	bitmask = nmk_gpio_get_bitmask(gpio);
+	if (!nmk_chip)
+		return;
+
+	/* we must individually clear the two edges */
+	spin_lock_irqsave(&nmk_chip->lock, flags);
+	if (nmk_chip->edge_rising & bitmask) {
+		reg = readl(nmk_chip->addr + NMK_GPIO_RWIMSC);
+		reg &= ~bitmask;
+		writel(reg, nmk_chip->addr + NMK_GPIO_RWIMSC);
+	}
+	if (nmk_chip->edge_falling & bitmask) {
+		reg = readl(nmk_chip->addr + NMK_GPIO_FWIMSC);
+		reg &= ~bitmask;
+		writel(reg, nmk_chip->addr + NMK_GPIO_FWIMSC);
+	}
+	spin_unlock_irqrestore(&nmk_chip->lock, flags);
+};
+
+static void nmk_gpio_irq_unmask(unsigned int irq)
+{
+	int gpio;
+	struct nmk_gpio_chip *nmk_chip;
+	unsigned long flags;
+	u32 bitmask, reg;
+
+	gpio = NOMADIK_IRQ_TO_GPIO(irq);
+	nmk_chip = get_irq_chip_data(irq);
+	bitmask = nmk_gpio_get_bitmask(gpio);
+	if (!nmk_chip)
+		return;
+
+	/* we must individually set the two edges */
+	spin_lock_irqsave(&nmk_chip->lock, flags);
+	if (nmk_chip->edge_rising & bitmask) {
+		reg = readl(nmk_chip->addr + NMK_GPIO_RWIMSC);
+		reg |= bitmask;
+		writel(reg, nmk_chip->addr + NMK_GPIO_RWIMSC);
+	}
+	if (nmk_chip->edge_falling & bitmask) {
+		reg = readl(nmk_chip->addr + NMK_GPIO_FWIMSC);
+		reg |= bitmask;
+		writel(reg, nmk_chip->addr + NMK_GPIO_FWIMSC);
+	}
+	spin_unlock_irqrestore(&nmk_chip->lock, flags);
+}
+
+static int nmk_gpio_irq_set_type(unsigned int irq, unsigned int type)
+{
+	int gpio;
+	struct nmk_gpio_chip *nmk_chip;
+	unsigned long flags;
+	u32 bitmask;
+
+	gpio = NOMADIK_IRQ_TO_GPIO(irq);
+	nmk_chip = get_irq_chip_data(irq);
+	bitmask = nmk_gpio_get_bitmask(gpio);
+	if (!nmk_chip)
+		return -EINVAL;
+
+	if (type & IRQ_TYPE_LEVEL_HIGH)
+		return -EINVAL;
+	if (type & IRQ_TYPE_LEVEL_LOW)
+		return -EINVAL;
+
+	spin_lock_irqsave(&nmk_chip->lock, flags);
+
+	nmk_chip->edge_rising &= ~bitmask;
+	if (type & IRQ_TYPE_EDGE_RISING)
+		nmk_chip->edge_rising |= bitmask;
+	writel(nmk_chip->edge_rising, nmk_chip->addr + NMK_GPIO_RIMSC);
+
+	nmk_chip->edge_falling &= ~bitmask;
+	if (type & IRQ_TYPE_EDGE_FALLING)
+		nmk_chip->edge_falling |= bitmask;
+	writel(nmk_chip->edge_falling, nmk_chip->addr + NMK_GPIO_FIMSC);
+
+	spin_unlock_irqrestore(&nmk_chip->lock, flags);
+
+	nmk_gpio_irq_unmask(irq);
+
+	return 0;
+}
+
+static struct irq_chip nmk_gpio_irq_chip = {
+	.name		= "Nomadik-GPIO",
+	.ack		= nmk_gpio_irq_ack,
+	.mask		= nmk_gpio_irq_mask,
+	.unmask		= nmk_gpio_irq_unmask,
+	.set_type	= nmk_gpio_irq_set_type,
+};
+
+static void nmk_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	struct nmk_gpio_chip *nmk_chip;
+	struct irq_chip *host_chip;
+	unsigned int gpio_irq;
+	u32 pending;
+	unsigned int first_irq;
+
+	nmk_chip = get_irq_data(irq);
+	first_irq = NOMADIK_GPIO_TO_IRQ(nmk_chip->chip.base);
+	while ( (pending = readl(nmk_chip->addr + NMK_GPIO_IS)) ) {
+		gpio_irq = first_irq + __ffs(pending);
+		generic_handle_irq(gpio_irq);
+	}
+	if (0) {/* don't ack parent irq, as ack == disable */
+		host_chip = get_irq_chip(irq);
+		host_chip->ack(irq);
+	}
+}
+
+static int nmk_gpio_init_irq(struct nmk_gpio_chip *nmk_chip)
+{
+	unsigned int first_irq;
+	int i;
+
+	first_irq = NOMADIK_GPIO_TO_IRQ(nmk_chip->chip.base);
+	for (i = first_irq; i < first_irq + NMK_GPIO_PER_CHIP; i++) {
+		set_irq_chip(i, &nmk_gpio_irq_chip);
+		set_irq_handler(i, handle_edge_irq);
+		set_irq_flags(i, IRQF_VALID);
+		set_irq_chip_data(i, nmk_chip);
+	}
+	set_irq_chained_handler(nmk_chip->parent_irq, nmk_gpio_irq_handler);
+	set_irq_data(nmk_chip->parent_irq, nmk_chip);
+	return 0;
+}
+
+/* I/O Functions */
+static int nmk_gpio_make_input(struct gpio_chip *chip, unsigned offset)
+{
+	struct nmk_gpio_chip *nmk_chip =
+		container_of(chip, struct nmk_gpio_chip, chip);
+
+	writel(1 << offset, nmk_chip->addr + NMK_GPIO_DIRC);
+	return 0;
+}
+
+static int nmk_gpio_make_output(struct gpio_chip *chip, unsigned offset,
+				int val)
+{
+	struct nmk_gpio_chip *nmk_chip =
+		container_of(chip, struct nmk_gpio_chip, chip);
+
+	writel(1 << offset, nmk_chip->addr + NMK_GPIO_DIRS);
+	return 0;
+}
+
+static int nmk_gpio_get_input(struct gpio_chip *chip, unsigned offset)
+{
+	struct nmk_gpio_chip *nmk_chip =
+		container_of(chip, struct nmk_gpio_chip, chip);
+	u32 bit = 1 << offset;
+
+	return (readl(nmk_chip->addr + NMK_GPIO_DAT) & bit) != 0;
+}
+
+static void nmk_gpio_set_output(struct gpio_chip *chip, unsigned offset,
+				int val)
+{
+	struct nmk_gpio_chip *nmk_chip =
+		container_of(chip, struct nmk_gpio_chip, chip);
+	u32 bit = 1 << offset;
+
+	if (val)
+		writel(bit, nmk_chip->addr + NMK_GPIO_DATS);
+	else
+		writel(bit, nmk_chip->addr + NMK_GPIO_DATC);
+}
+
+/* This structure is replicated for each GPIO block allocated at probe time */
+static struct gpio_chip nmk_gpio_template = {
+	.direction_input	= nmk_gpio_make_input,
+	.get			= nmk_gpio_get_input,
+	.direction_output	= nmk_gpio_make_output,
+	.set			= nmk_gpio_set_output,
+	.ngpio			= NMK_GPIO_PER_CHIP,
+	.can_sleep		= 0,
+};
+
+static int __init nmk_gpio_probe(struct amba_device *dev, struct amba_id *id)
+{
+	struct nmk_gpio_platform_data *pdata;
+	struct nmk_gpio_chip *nmk_chip;
+	struct gpio_chip *chip;
+	int ret;
+
+	pdata = dev->dev.platform_data;
+	ret = amba_request_regions(dev, pdata->name);
+	if (ret)
+		return ret;
+
+	nmk_chip = kzalloc(sizeof(*nmk_chip), GFP_KERNEL);
+	if (!nmk_chip) {
+		ret = -ENOMEM;
+		goto out_amba;
+	}
+	/*
+	 * The virt address in nmk_chip->addr is in the nomadik register space,
+	 * so we can simply convert the resource address, without remapping
+	 */
+	nmk_chip->addr = io_p2v(dev->res.start);
+	nmk_chip->chip = nmk_gpio_template;
+	nmk_chip->parent_irq = pdata->parent_irq;
+
+	chip = &nmk_chip->chip;
+	chip->base = pdata->first_gpio;
+	chip->label = pdata->name;
+	chip->dev = &dev->dev;
+	chip->owner = THIS_MODULE;
+
+	ret = gpiochip_add(&nmk_chip->chip);
+	if (ret)
+		goto out_free;
+
+	amba_set_drvdata(dev, nmk_chip);
+
+	nmk_gpio_init_irq(nmk_chip);
+
+	dev_info(&dev->dev, "Bits %i-%i at address %p\n",
+		 nmk_chip->chip.base, nmk_chip->chip.base+31, nmk_chip->addr);
+	return 0;
+
+ out_free:
+	kfree(nmk_chip);
+ out_amba:
+	amba_release_regions(dev);
+	dev_err(&dev->dev, "Failure %i for GPIO %i-%i\n", ret,
+		  pdata->first_gpio, pdata->first_gpio+31);
+	return ret;
+}
+
+static int nmk_gpio_remove(struct amba_device *dev)
+{
+	struct nmk_gpio_chip *nmk_chip;
+
+	nmk_chip = amba_get_drvdata(dev);
+	gpiochip_remove(&nmk_chip->chip);
+	kfree(nmk_chip);
+	amba_release_regions(dev);
+	return 0;
+}
+
+
+/* We have 0x1f080060 and 0x1f180060, accept both using the mask */
+static struct amba_id nmk_gpio_ids[] = {
+	{
+		.id	= 0x1f080060,
+		.mask	= 0xffefffff,
+	},
+	{0, 0},
+};
+
+static struct amba_driver nmk_gpio_driver = {
+	.drv = {
+		.owner = THIS_MODULE,
+		.name = "gpio",
+		},
+	.probe = nmk_gpio_probe,
+	.remove = nmk_gpio_remove,
+	.suspend = NULL, /* to be done */
+	.resume = NULL,
+	.id_table = nmk_gpio_ids,
+};
+
+static int __init nmk_gpio_init(void)
+{
+	return amba_driver_register(&nmk_gpio_driver);
+}
+
+arch_initcall(nmk_gpio_init);
+
+MODULE_AUTHOR("Prafulla WADASKAR and Alessandro Rubini");
+MODULE_DESCRIPTION("Nomadik GPIO Driver");
+MODULE_LICENSE("GPL");
+
+

arch/arm/mach-nomadik/i2c-8815nhk.c

+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/i2c-algo-bit.h>
+#include <linux/i2c-gpio.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+
+/*
+ * There are two busses in the 8815NHK.
+ * They could, in theory, be driven by the hardware component, but we
+ * use bit-bang through GPIO by now, to keep things simple
+ */
+
+static struct i2c_gpio_platform_data nhk8815_i2c_data0 = {
+	/* keep defaults for timeouts; pins are push-pull bidirectional */
+	.scl_pin = 62,
+	.sda_pin = 63,
+};
+
+static struct i2c_gpio_platform_data nhk8815_i2c_data1 = {
+	/* keep defaults for timeouts; pins are push-pull bidirectional */
+	.scl_pin = 53,
+	.sda_pin = 54,
+};
+
+/* first bus: GPIO XX and YY */
+static struct platform_device nhk8815_i2c_dev0 = {
+	.name	= "i2c-gpio",
+	.id	= 0,
+	.dev	= {
+		.platform_data = &nhk8815_i2c_data0,
+	},
+};
+/* second bus: GPIO XX and YY */
+static struct platform_device nhk8815_i2c_dev1 = {
+	.name	= "i2c-gpio",
+	.id	= 1,
+	.dev	= {
+		.platform_data = &nhk8815_i2c_data1,
+	},
+};
+
+static int __init nhk8815_i2c_init(void)
+{
+	nmk_gpio_set_mode(nhk8815_i2c_data0.scl_pin, NMK_GPIO_ALT_GPIO);
+	nmk_gpio_set_mode(nhk8815_i2c_data0.sda_pin, NMK_GPIO_ALT_GPIO);
+	platform_device_register(&nhk8815_i2c_dev0);
+
+	nmk_gpio_set_mode(nhk8815_i2c_data1.scl_pin, NMK_GPIO_ALT_GPIO);
+	nmk_gpio_set_mode(nhk8815_i2c_data1.sda_pin, NMK_GPIO_ALT_GPIO);
+	platform_device_register(&nhk8815_i2c_dev1);
+
+	return 0;
+}
+
+static void __exit nhk8815_i2c_exit(void)
+{
+	platform_device_unregister(&nhk8815_i2c_dev0);
+	platform_device_unregister(&nhk8815_i2c_dev1);
+	return;
+}
+
+module_init(nhk8815_i2c_init);
+module_exit(nhk8815_i2c_exit);

arch/arm/mach-nomadik/include/mach/clkdev.h

+#ifndef __ASM_MACH_CLKDEV_H
+#define __ASM_MACH_CLKDEV_H
+
+#define __clk_get(clk) ({ 1; })
+#define __clk_put(clk) do { } while (0)
+
+#endif

arch/arm/mach-nomadik/include/mach/debug-macro.S

+/*
+ * Debugging macro include header
+ *
+ *  Copyright (C) 1994-1999 Russell King
+ *  Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+		.macro	addruart,rx
+		mrc	p15, 0, \rx, c1, c0
+		tst	\rx, #1			@ MMU enabled?
+		moveq	\rx, #0x10000000	@ physical base address
+		movne	\rx, #0xf0000000	@ virtual base
+		add	\rx, \rx, #0x00100000
+		add	\rx, \rx, #0x000fb000
+		.endm
+
+#include <asm/hardware/debug-pl01x.S>

arch/arm/mach-nomadik/include/mach/entry-macro.S

+/*
+ * Low-level IRQ helper macros for Nomadik platforms
+ *
+ * This file is licensed under  the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+
+	.macro	disable_fiq
+	.endm
+
+	.macro	get_irqnr_preamble, base, tmp
+	ldr	\base, =IO_ADDRESS(NOMADIK_IC_BASE)
+	.endm
+
+	.macro	arch_ret_to_user, tmp1, tmp2
+	.endm
+
+	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+	/* This stanza gets the irq mask from one of two status registers */
+	mov	\irqnr, #0
+	ldr	\irqstat, [\base, #VIC_REG_IRQSR0]	@ get masked status
+	cmp	\irqstat, #0
+	bne	1001f
+	add	\irqnr, \irqnr, #32
+	ldr	\irqstat, [\base, #VIC_REG_IRQSR1]	@ get masked status
+
+1001:	tst	\irqstat, #15
+	bne	1002f
+	add	\irqnr, \irqnr, #4
+	movs	\irqstat, \irqstat, lsr #4
+	bne	1001b
+1002:	tst	\irqstat, #1
+	bne	1003f
+	add	\irqnr, \irqnr, #1
+	movs	\irqstat, \irqstat, lsr #1
+	bne	1002b
+1003:	/* EQ will be set if no irqs pending */
+	.endm

arch/arm/mach-nomadik/include/mach/gpio.h

+/*
+ * Structures and registers for GPIO access in the Nomadik SoC
+ *
+ * Copyright (C) 2008 STMicroelectronics
+ *     Author: Prafulla WADASKAR <prafulla.wadaskar@st.com>
+ * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_ARCH_GPIO_H
+#define __ASM_ARCH_GPIO_H
+
+#include <asm-generic/gpio.h>
+
+/*
+ * These currently cause a function call to happen, they may be optimized
+ * if needed by adding cpu-specific defines to identify blocks
+ * (see mach-pxa/include/mach/gpio.h as an example using GPLR etc)
+ */
+#define gpio_get_value  __gpio_get_value
+#define gpio_set_value  __gpio_set_value
+#define gpio_cansleep   __gpio_cansleep
+#define gpio_to_irq     __gpio_to_irq
+
+/*
+ * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving
+ * the "gpio" namespace for generic and cross-machine functions
+ */
+
+/* Register in the logic block */
+#define NMK_GPIO_DAT	0x00
+#define NMK_GPIO_DATS	0x04
+#define NMK_GPIO_DATC	0x08
+#define NMK_GPIO_PDIS	0x0c
+#define NMK_GPIO_DIR	0x10
+#define NMK_GPIO_DIRS	0x14
+#define NMK_GPIO_DIRC	0x18
+#define NMK_GPIO_SLPC	0x1c
+#define NMK_GPIO_AFSLA	0x20
+#define NMK_GPIO_AFSLB	0x24
+
+#define NMK_GPIO_RIMSC	0x40
+#define NMK_GPIO_FIMSC	0x44
+#define NMK_GPIO_IS	0x48
+#define NMK_GPIO_IC	0x4c
+#define NMK_GPIO_RWIMSC	0x50
+#define NMK_GPIO_FWIMSC	0x54
+#define NMK_GPIO_WKS	0x58
+
+/* Alternate functions: function C is set in hw by setting both A and B */
+#define NMK_GPIO_ALT_GPIO	0
+#define NMK_GPIO_ALT_A	1
+#define NMK_GPIO_ALT_B	2
+#define NMK_GPIO_ALT_C	(NMK_GPIO_ALT_A | NMK_GPIO_ALT_B)
+
+extern int nmk_gpio_set_mode(int gpio, int gpio_mode);
+extern int nmk_gpio_get_mode(int gpio);
+
+/*
+ * Platform data to register a block: only the initial gpio/irq number.
+ */
+struct nmk_gpio_platform_data {
+	char *name;
+	int first_gpio;
+	int first_irq;
+	int parent_irq;
+};
+
+#endif /* __ASM_ARCH_GPIO_H */

arch/arm/mach-nomadik/include/mach/hardware.h

+/*
+ * This file contains the hardware definitions of the Nomadik.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * YOU should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
+ */
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+/* Nomadik registers live from 0x1000.0000 to 0x1023.0000 -- currently */
+#define NOMADIK_IO_VIRTUAL	0xF0000000	/* VA of IO  */
+#define NOMADIK_IO_PHYSICAL	0x10000000	/* PA of IO */
+#define NOMADIK_IO_SIZE		0x00300000	/* 3MB for all regs */
+
+/* used in C code, so cast to proper type */
+#define io_p2v(x) ((void __iomem *)(x) \
+			- NOMADIK_IO_PHYSICAL + NOMADIK_IO_VIRTUAL)
+#define io_v2p(x) ((unsigned long)(x) \
+			- NOMADIK_IO_VIRTUAL + NOMADIK_IO_PHYSICAL)
+
+/* used in asm code, so no casts */
+#define IO_ADDRESS(x) ((x) - NOMADIK_IO_PHYSICAL + NOMADIK_IO_VIRTUAL)
+
+/*
+ *   Base address defination for Nomadik Onchip Logic Block
+ */
+#define NOMADIK_FSMC_BASE	0x10100000	/* FSMC registers */
+#define NOMADIK_SDRAMC_BASE	0x10110000	/* SDRAM Controller */
+#define NOMADIK_CLCDC_BASE	0x10120000	/* CLCD Controller */
+#define NOMADIK_MDIF_BASE	0x10120000	/* MDIF */
+#define NOMADIK_DMA0_BASE	0x10130000	/* DMA0 Controller */
+#define NOMADIK_IC_BASE		0x10140000	/* Vectored Irq Controller */
+#define NOMADIK_DMA1_BASE	0x10150000	/* DMA1 Controller */
+#define NOMADIK_USB_BASE	0x10170000	/* USB-OTG conf reg base */
+#define NOMADIK_CRYP_BASE	0x10180000	/* Crypto processor */
+#define NOMADIK_SHA1_BASE	0x10190000	/* SHA-1 Processor */
+#define NOMADIK_XTI_BASE	0x101A0000	/* XTI */
+#define NOMADIK_RNG_BASE	0x101B0000	/* Random number generator */
+#define NOMADIK_SRC_BASE	0x101E0000	/* SRC base */
+#define NOMADIK_WDOG_BASE	0x101E1000	/* Watchdog */
+#define NOMADIK_MTU0_BASE	0x101E2000	/* Multiple Timer 0 */
+#define NOMADIK_MTU1_BASE	0x101E3000	/* Multiple Timer 1 */
+#define NOMADIK_GPIO0_BASE	0x101E4000	/* GPIO0 */
+#define NOMADIK_GPIO1_BASE	0x101E5000	/* GPIO1 */
+#define NOMADIK_GPIO2_BASE	0x101E6000	/* GPIO2 */
+#define NOMADIK_GPIO3_BASE	0x101E7000	/* GPIO3 */
+#define NOMADIK_RTC_BASE	0x101E8000	/* Real Time Clock base */
+#define NOMADIK_PMU_BASE	0x101E9000	/* Power Management Unit */
+#define NOMADIK_OWM_BASE	0x101EA000	/* One wire master */
+#define NOMADIK_SCR_BASE	0x101EF000	/* Secure Control registers */
+#define NOMADIK_MSP2_BASE	0x101F0000	/* MSP 2 interface */
+#define NOMADIK_MSP1_BASE	0x101F1000	/* MSP 1 interface */
+#define NOMADIK_UART2_BASE	0x101F2000	/* UART 2 interface */
+#define NOMADIK_SSIRx_BASE	0x101F3000	/* SSI 8-ch rx interface */
+#define NOMADIK_SSITx_BASE	0x101F4000	/* SSI 8-ch tx interface */
+#define NOMADIK_MSHC_BASE	0x101F5000	/* Memory Stick(Pro) Host */
+#define NOMADIK_SDI_BASE	0x101F6000	/* SD-card/MM-Card */
+#define NOMADIK_I2C1_BASE	0x101F7000	/* I2C1 interface */
+#define NOMADIK_I2C0_BASE	0x101F8000	/* I2C0 interface */
+#define NOMADIK_MSP0_BASE	0x101F9000	/* MSP 0 interface  */
+#define NOMADIK_FIRDA_BASE	0x101FA000	/* FIrDA interface  */
+#define NOMADIK_UART1_BASE	0x101FB000	/* UART 1 interface */
+#define NOMADIK_SSP_BASE	0x101FC000	/* SSP interface  */
+#define NOMADIK_UART0_BASE	0x101FD000	/* UART 0 interface */
+#define NOMADIK_SGA_BASE	0x101FE000	/* SGA interface */
+#define NOMADIK_L2CC_BASE	0x10210000	/* L2 Cache controller */
+
+/* Other ranges, not for p2v/v2p */
+#define NOMADIK_BACKUP_RAM	0x80010000
+#define NOMADIK_EBROM		0x80000000	/* Embedded boot ROM */
+#define NOMADIK_HAMACV_DMEM_BASE 0xA0100000	/* HAMACV Data Memory Start */
+#define NOMADIK_HAMACV_DMEM_END	0xA01FFFFF	/* HAMACV Data Memory End */
+#define NOMADIK_HAMACA_DMEM	0xA0200000	/* HAMACA Data Memory Space */
+
+#define NOMADIK_FSMC_VA		IO_ADDRESS(NOMADIK_FSMC_BASE)
+#define NOMADIK_MTU0_VA		IO_ADDRESS(NOMADIK_MTU0_BASE)
+#define NOMADIK_MTU1_VA		IO_ADDRESS(NOMADIK_MTU1_BASE)
+
+#endif /* __ASM_ARCH_HARDWARE_H */

arch/arm/mach-nomadik/include/mach/io.h

+/*
+ * arch/arm/mach-nomadik/include/mach/io.h   (copied from mach-sa1100)
+ *
+ * Copyright (C) 1997-1999 Russell King
+ *
+ * Modifications:
+ *  06-12-1997  RMK     Created.
+ *  07-04-1999  RMK     Major cleanup
+ */
+#ifndef __ASM_ARM_ARCH_IO_H
+#define __ASM_ARM_ARCH_IO_H
+
+#define IO_SPACE_LIMIT 0xffffffff
+
+/*
+ * We don't actually have real ISA nor PCI buses, but there is so many
+ * drivers out there that might just work if we fake them...
+ */
+#define __io(a)         __typesafe_io(a)
+#define __mem_pci(a)    (a)
+
+#endif

arch/arm/mach-nomadik/include/mach/irqs.h

+/*
+ *  mach-nomadik/include/mach/irqs.h
+ *
+ *  Copyright (C) ST Microelectronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_IRQS_H
+#define __ASM_ARCH_IRQS_H
+
+#include <mach/hardware.h>
+
+#define IRQ_VIC_START		0	/* first VIC interrupt is 0 */
+
+/*
+ * Interrupt numbers generic for all Nomadik Chip cuts
+ */
+#define IRQ_WATCHDOG			0
+#define IRQ_SOFTINT			1
+#define IRQ_CRYPTO			2
+#define IRQ_OWM				3
+#define IRQ_MTU0			4
+#define IRQ_MTU1			5
+#define IRQ_GPIO0			6
+#define IRQ_GPIO1			7
+#define IRQ_GPIO2			8
+#define IRQ_GPIO3			9
+#define IRQ_RTC_RTT			10
+#define IRQ_SSP				11
+#define IRQ_UART0			12
+#define IRQ_DMA1			13
+#define IRQ_CLCD_MDIF			14
+#define IRQ_DMA0			15
+#define IRQ_PWRFAIL			16
+#define IRQ_UART1			17
+#define IRQ_FIRDA			18
+#define IRQ_MSP0			19
+#define IRQ_I2C0			20
+#define IRQ_I2C1			21
+#define IRQ_SDMMC			22
+#define IRQ_USBOTG			23
+#define IRQ_SVA_IT0			24
+#define IRQ_SVA_IT1			25
+#define IRQ_SAA_IT0			26
+#define IRQ_SAA_IT1			27
+#define IRQ_UART2			28
+#define IRQ_MSP2			31
+#define IRQ_L2CC			48
+#define IRQ_HPI				49
+#define IRQ_SKE				50
+#define IRQ_KP				51
+#define IRQ_MEMST			54
+#define IRQ_SGA_IT			58
+#define IRQ_USBM			60
+#define IRQ_MSP1			62
+
+#define NOMADIK_SOC_NR_IRQS		64
+
+/* After chip-specific IRQ numbers we have the GPIO ones */
+#define NOMADIK_NR_GPIO			128 /* last 4 not wired to pins */
+#define NOMADIK_GPIO_TO_IRQ(gpio)	((gpio) + NOMADIK_SOC_NR_IRQS)
+#define NOMADIK_IRQ_TO_GPIO(irq)	((irq) - NOMADIK_SOC_NR_IRQS)
+#define NR_IRQS				NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO)
+
+/* Following two are used by entry_macro.S, to access our dual-vic */
+#define VIC_REG_IRQSR0		0
+#define VIC_REG_IRQSR1		0x20
+
+#endif /* __ASM_ARCH_IRQS_H */
+

arch/arm/mach-nomadik/include/mach/memory.h

+/*
+ *  mach-nomadik/include/mach/memory.h
+ *
+ *  Copyright (C) 1999 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+/*
+ * Physical DRAM offset.
+ */
+#define PHYS_OFFSET	UL(0x00000000)
+
+#endif

arch/arm/mach-nomadik/include/mach/mtu.h

+#ifndef __ASM_ARCH_MTU_H
+#define __ASM_ARCH_MTU_H
+
+/*
+ * The MTU device hosts four different counters, with 4 set of
+ * registers. These are register names.
+ */
+
+#define MTU_IMSC	0x00	/* Interrupt mask set/clear */
+#define MTU_RIS		0x04	/* Raw interrupt status */
+#define MTU_MIS		0x08	/* Masked interrupt status */
+#define MTU_ICR		0x0C	/* Interrupt clear register */
+
+/* per-timer registers take 0..3 as argument */
+#define MTU_LR(x)	(0x10 + 0x10 * (x) + 0x00)	/* Load value */
+#define MTU_VAL(x)	(0x10 + 0x10 * (x) + 0x04)	/* Current value */
+#define MTU_CR(x)	(0x10 + 0x10 * (x) + 0x08)	/* Control reg */
+#define MTU_BGLR(x)	(0x10 + 0x10 * (x) + 0x0c)	/* At next overflow */
+
+/* bits for the control register */
+#define MTU_CRn_ENA		0x80
+#define MTU_CRn_PERIODIC	0x40	/* if 0 = free-running */
+#define MTU_CRn_PRESCALE_MASK	0x0c
+#define MTU_CRn_PRESCALE_1		0x00
+#define MTU_CRn_PRESCALE_16		0x04
+#define MTU_CRn_PRESCALE_256		0x08
+#define MTU_CRn_32BITS		0x02
+#define MTU_CRn_ONESHOT		0x01	/* if 0 = wraps reloading from BGLR*/
+
+/* Other registers are usual amba/primecell registers, currently not used */
+#define MTU_ITCR	0xff0
+#define MTU_ITOP	0xff4
+
+#define MTU_PERIPH_ID0	0xfe0
+#define MTU_PERIPH_ID1	0xfe4
+#define MTU_PERIPH_ID2	0xfe8
+#define MTU_PERIPH_ID3	0xfeC
+
+#define MTU_PCELL0	0xff0
+#define MTU_PCELL1	0xff4
+#define MTU_PCELL2	0xff8
+#define MTU_PCELL3	0xffC
+
+#endif /* __ASM_ARCH_MTU_H */
+

arch/arm/mach-nomadik/include/mach/setup.h

+
+/*
+ * These symbols are needed for board-specific files to call their
+ * own cpu-specific files
+ */
+
+#ifndef __ASM_ARCH_SETUP_H
+#define __ASM_ARCH_SETUP_H
+
+#include <asm/mach/time.h>
+#include <linux/init.h>
+
+#ifdef CONFIG_NOMADIK_8815
+
+extern void cpu8815_map_io(void);
+extern void cpu8815_platform_init(void);
+extern void cpu8815_init_irq(void);
+extern struct sys_timer nomadik_timer;
+
+#endif /* NOMADIK_8815 */
+
+#endif /*  __ASM_ARCH_SETUP_H */

arch/arm/mach-nomadik/include/mach/system.h

+/*
+ *  mach-nomadik/include/mach/system.h
+ *
+ *  Copyright (C) 2008 STMicroelectronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_SYSTEM_H
+#define __ASM_ARCH_SYSTEM_H
+
+#include <linux/io.h>
+#include <mach/hardware.h>
+
+static inline void arch_idle(void)
+{
+	/*
+	 * This should do all the clock switching
+	 * and wait for interrupt tricks
+	 */
+	cpu_do_idle();
+}
+
+static inline void arch_reset(char mode, const char *cmd)
+{
+	void __iomem *src_rstsr = io_p2v(NOMADIK_SRC_BASE + 0x18);
+
+	/* FIXME: use egpio when implemented */
+
+	/* Write anything to Reset status register */
+	writel(1, src_rstsr);
+}
+
+#endif

arch/arm/mach-nomadik/include/mach/timex.h

+#ifndef __ASM_ARCH_TIMEX_H
+#define __ASM_ARCH_TIMEX_H
+
+#define CLOCK_TICK_RATE         2400000
+
+#endif

arch/arm/mach-nomadik/include/mach/uncompress.h

+/*
+ *  Copyright (C) 2008 STMicroelectronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __ASM_ARCH_UNCOMPRESS_H
+#define __ASM_ARCH_UNCOMPRESS_H
+
+#include <asm/setup.h>
+#include <asm/io.h>
+#include <mach/hardware.h>
+
+/* we need the constants in amba/serial.h, but it refers to amba_device */
+struct amba_device;
+#include <linux/amba/serial.h>
+
+#define NOMADIK_UART_DR		0x101FB000
+#define NOMADIK_UART_LCRH	0x101FB02c
+#define NOMADIK_UART_CR		0x101FB030
+#define NOMADIK_UART_FR		0x101FB018
+
+static void putc(const char c)
+{
+	/* Do nothing if the UART is not enabled. */
+	if (!(readb(NOMADIK_UART_CR) & UART01x_CR_UARTEN))
+		return;
+
+	if (c == '\n')
+		putc('\r');
+
+	while (readb(NOMADIK_UART_FR) & UART01x_FR_TXFF)
+		barrier();
+	writeb(c, NOMADIK_UART_DR);
+}
+
+static void flush(void)
+{
+	if (!(readb(NOMADIK_UART_CR) & UART01x_CR_UARTEN))
+		return;
+	while (readb(NOMADIK_UART_FR) & UART01x_FR_BUSY)
+		barrier();
+}
+
+static inline void arch_decomp_setup(void)
+{
+}
+
+#define arch_decomp_wdog() /* nothing to do here */
+
+#endif /* __ASM_ARCH_UNCOMPRESS_H */

arch/arm/mach-nomadik/include/mach/vmalloc.h

+
+#define VMALLOC_END       0xe8000000

arch/arm/mach-nomadik/timer.c

+/*
+ *  linux/arch/arm/mach-nomadik/timer.c
+ *
+ * Copyright (C) 2008 STMicroelectronics
+ * Copyright (C) 2009 Alessandro Rubini, somewhat based on at91sam926x
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/clockchips.h>
+#include <linux/jiffies.h>
+#include <asm/mach/time.h>
+#include <mach/mtu.h>
+
+#define TIMER_CTRL	0x80	/* No divisor */
+#define TIMER_PERIODIC	0x40
+#define TIMER_SZ32BIT	0x02
+
+/* Initial value for SRC control register: all timers use MXTAL/8 source */
+#define SRC_CR_INIT_MASK	0x00007fff
+#define SRC_CR_INIT_VAL		0x2aaa8000
+
+static u32	nmdk_count;		/* accumulated count */
+static u32	nmdk_cycle;		/* write-once */
+static __iomem void *mtu_base;
+
+/*
+ * clocksource: the MTU device is a decrementing counters, so we negate
+ * the value being read.
+ */
+static cycle_t nmdk_read_timer(struct clocksource *cs)
+{
+	u32 count = readl(mtu_base + MTU_VAL(0));
+	return nmdk_count + nmdk_cycle - count;
+
+}
+
+static struct clocksource nmdk_clksrc = {
+	.name		= "mtu_0",
+	.rating		= 120,
+	.read		= nmdk_read_timer,
+	.shift		= 20,
+	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+/*
+ * Clockevent device: currently only periodic mode is supported
+ */
+static void nmdk_clkevt_mode(enum clock_event_mode mode,
+			     struct clock_event_device *dev)
+{
+	unsigned long flags;
+
+	switch (mode) {
+	case CLOCK_EVT_MODE_PERIODIC:
+		/* enable interrupts -- and count current value? */
+		raw_local_irq_save(flags);
+		writel(readl(mtu_base + MTU_IMSC) | 1, mtu_base + MTU_IMSC);
+		raw_local_irq_restore(flags);
+		break;
+	case CLOCK_EVT_MODE_ONESHOT:
+		BUG(); /* Not supported, yet */
+		/* FALLTHROUGH */
+	case CLOCK_EVT_MODE_SHUTDOWN:
+	case CLOCK_EVT_MODE_UNUSED:
+		/* disable irq */
+		raw_local_irq_save(flags);
+		writel(readl(mtu_base + MTU_IMSC) & ~1, mtu_base + MTU_IMSC);
+		raw_local_irq_restore(flags);
+		break;
+	case CLOCK_EVT_MODE_RESUME:
+		break;
+	}
+}
+
+static struct clock_event_device nmdk_clkevt = {
+	.name		= "mtu_0",
+	.features	= CLOCK_EVT_FEAT_PERIODIC,
+	.shift		= 32,
+	.rating		= 100,
+	.set_mode	= nmdk_clkevt_mode,
+};
+
+/*
+ * IRQ Handler for the timer 0 of the MTU block. The irq is not shared
+ * as we are the only users of mtu0 by now.
+ */
+static irqreturn_t nmdk_timer_interrupt(int irq, void *dev_id)
+{
+	/* ack: "interrupt clear register" */
+	writel( 1 << 0, mtu_base + MTU_ICR);
+
+	/* we can't count lost ticks, unfortunately */
+	nmdk_count += nmdk_cycle;
+	nmdk_clkevt.event_handler(&nmdk_clkevt);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Set up timer interrupt, and return the current time in seconds.
+ */
+static struct irqaction nmdk_timer_irq = {
+	.name		= "Nomadik Timer Tick",
+	.flags		= IRQF_DISABLED | IRQF_TIMER,
+	.handler	= nmdk_timer_interrupt,
+};
+
+static void nmdk_timer_reset(void)
+{
+	u32 cr;
+
+	writel(0, mtu_base + MTU_CR(0)); /* off */
+
+	/* configure load and background-load, and fire it up */
+	writel(nmdk_cycle, mtu_base + MTU_LR(0));
+	writel(nmdk_cycle, mtu_base + MTU_BGLR(0));
+	cr = MTU_CRn_PERIODIC | MTU_CRn_PRESCALE_1 | MTU_CRn_32BITS;
+	writel(cr, mtu_base + MTU_CR(0));
+	writel(cr | MTU_CRn_ENA, mtu_base + MTU_CR(0));
+}
+
+static void __init nmdk_timer_init(void)
+{
+	u32 src_cr;
+	unsigned long rate;
+	int bits;
+
+	rate = CLOCK_TICK_RATE; /* 2.4MHz */
+	nmdk_cycle = (rate + HZ/2) / HZ;
+
+	/* Configure timer sources in "system reset controller" ctrl reg */
+	src_cr = readl(io_p2v(NOMADIK_SRC_BASE));
+	src_cr &= SRC_CR_INIT_MASK;
+	src_cr |= SRC_CR_INIT_VAL;
+	writel(src_cr, io_p2v(NOMADIK_SRC_BASE));
+
+	/* Save global pointer to mtu, used by functions above */
+	mtu_base = io_p2v(NOMADIK_MTU0_BASE);
+
+	/* Init the timer and register clocksource */
+	nmdk_timer_reset();
+
+	nmdk_clksrc.mult = clocksource_hz2mult(rate, nmdk_clksrc.shift);
+	bits =  8*sizeof(nmdk_count);
+	nmdk_clksrc.mask = CLOCKSOURCE_MASK(bits);
+
+	clocksource_register(&nmdk_clksrc);
+
+	/* Register irq and clockevents */
+	setup_irq(IRQ_MTU0, &nmdk_timer_irq);
+	nmdk_clkevt.mult = div_sc(rate, NSEC_PER_SEC, nmdk_clkevt.shift);
+	nmdk_clkevt.cpumask = cpumask_of(0);
+	clockevents_register_device(&nmdk_clkevt);
+}
+
+struct sys_timer nomadik_timer = {
+	.init		= nmdk_timer_init,
+};

arch/arm/mm/Kconfig

@@ -758,7 +758,7 @@ config CACHE_FEROCEON_L2_WRITETHROUGH
 config CACHE_L2X0
 	bool "Enable the L2x0 outer cache controller"
 	depends on REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP || MACH_REALVIEW_PB1176 || \
-		   REALVIEW_EB_A9MP || ARCH_MX35 || ARCH_MX31 || MACH_REALVIEW_PBX
+		   REALVIEW_EB_A9MP || ARCH_MX35 || ARCH_MX31 || MACH_REALVIEW_PBX || ARCH_NOMADIK
 	default y
 	select OUTER_CACHE
 	help