ARM: dts: i.MX27 boards: Switch to use standard GPIO and IRQ flags definitions

Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

arch/arm/boot/dts/imx27-apf27dev.dts

@@ -41,7 +41,7 @@
 
 		user-key {
 			label = "user";
-			gpios = <&gpio6 13 0>;
+			gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
 			linux,code = <276>; /* BTN_EXTRA */
 		};
 	};
@@ -51,7 +51,7 @@
 
 		user {
 			label = "Heartbeat";
-			gpios = <&gpio6 14 0>;
+			gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
@@ -59,7 +59,7 @@
 
 &cspi1 {
 	fsl,spi-num-chipselects = <1>;
-	cs-gpios = <&gpio4 28 1>;
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_cspi1>;
 	status = "okay";
@@ -67,8 +67,9 @@
 
 &cspi2 {
 	fsl,spi-num-chipselects = <3>;
-	cs-gpios = <&gpio4 21 1>, <&gpio4 27 1>,
-			<&gpio2 17 1>;
+	cs-gpios = <&gpio4 21 GPIO_ACTIVE_LOW>,
+		   <&gpio4 27 GPIO_ACTIVE_LOW>,
+		   <&gpio2 17 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_cspi2>;
 	status = "okay";
@@ -179,7 +180,7 @@
 
 &sdhci2 {
 	bus-width = <4>;
-	cd-gpios = <&gpio3 14 0>;
+	cd-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sdhc2>;
 	status = "okay";

arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts

@@ -124,7 +124,7 @@
 };
 
 &sdhci2 {
-	cd-gpios = <&gpio3 29 0>;
+	cd-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts

@@ -24,8 +24,8 @@
 
 &cspi1 {
 	fsl,spi-num-chipselects = <2>;
-	cs-gpios = <&gpio4 28 0>,
-		<&gpio4 27 0>;
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>,
+		   <&gpio4 27 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts

@@ -16,7 +16,8 @@
 
 &cspi1 {
 	fsl,spi-num-chipselects = <2>;
-	cs-gpios = <&gpio4 28 0>, <&gpio4 27 0>;
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>,
+		   <&gpio4 27 GPIO_ACTIVE_LOW>;
 };
 
 &i2c1 {
@@ -65,8 +66,8 @@
 
 &sdhci2 {
 	bus-width = <4>;
-	cd-gpios = <&gpio3 29 0>;
-	wp-gpios = <&gpio3 28 0>;
+	cd-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+	wp-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&vmmc1_reg>;
 	status = "okay";
 };
@@ -90,7 +91,7 @@
 		compatible = "nxp,sja1000";
 		reg = <4 0x00000000 0x00000100>;
 		interrupt-parent = <&gpio5>;
-		interrupts = <19 0x2>;
+		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
 		nxp,external-clock-frequency = <16000000>;
 		nxp,tx-output-config = <0x16>;
 		nxp,no-comparator-bypass;

arch/arm/boot/dts/imx27-phytec-phycore-som.dts

@@ -52,7 +52,7 @@
 
 &cspi1 {
 	fsl,spi-num-chipselects = <1>;
-	cs-gpios = <&gpio4 28 0>;
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
 	pmic: mc13783@0 {
@@ -62,7 +62,7 @@
 		spi-max-frequency = <20000000>;
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <23 0x4>;
+		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
 		fsl,mc13xxx-uses-adc;
 		fsl,mc13xxx-uses-rtc;
 
@@ -149,7 +149,7 @@
 
 &fec {
 	phy-mode = "mii";
-	phy-reset-gpios = <&gpio3 30 0>;
+	phy-reset-gpios = <&gpio3 30 GPIO_ACTIVE_HIGH>;
 	phy-supply = <&reg_3v3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec1>;

arch/arm/boot/dts/imx27.dtsi

@@ -11,6 +11,8 @@
 
 #include "skeleton.dtsi"
 #include "imx27-pinfunc.h"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	aliases {