[media] smiapp-pll: Try other pre-pll divisors

The smiapp pll calculator assumed that the minimum pre-pll divisor was
perfect. That may not always be the case, so let's try the others, too.
Typically there are just a few alternatives.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/i2c/smiapp-pll.c

@@ -58,7 +58,7 @@ static int bounds_check(struct device *dev, uint32_t val,
 	if (val >= min && val <= max)
 		return 0;
 
-	dev_warn(dev, "%s out of bounds: %d (%d--%d)\n", str, val, min, max);
+	dev_dbg(dev, "%s out of bounds: %d (%d--%d)\n", str, val, min, max);
 
 	return -EINVAL;
 }
@@ -87,14 +87,14 @@ static void print_pll(struct device *dev, struct smiapp_pll *pll)
 	dev_dbg(dev, "vt_pix_clk_freq_hz \t%d\n", pll->vt_pix_clk_freq_hz);
 }
 
-int smiapp_pll_calculate(struct device *dev, struct smiapp_pll_limits *limits,
-			 struct smiapp_pll *pll)
+static int __smiapp_pll_calculate(struct device *dev,
+				  struct smiapp_pll_limits *limits,
+				  struct smiapp_pll *pll, uint32_t mul,
+				  uint32_t div, uint32_t lane_op_clock_ratio)
 {
 	uint32_t sys_div;
 	uint32_t best_pix_div = INT_MAX >> 1;
 	uint32_t vt_op_binning_div;
-	uint32_t lane_op_clock_ratio;
-	uint32_t mul, div;
 	uint32_t more_mul_min, more_mul_max;
 	uint32_t more_mul_factor;
 	uint32_t min_vt_div, max_vt_div, vt_div;
@@ -102,54 +102,6 @@ int smiapp_pll_calculate(struct device *dev, struct smiapp_pll_limits *limits,
 	unsigned int i;
 	int rval;
 
-	if (pll->flags & SMIAPP_PLL_FLAG_OP_PIX_CLOCK_PER_LANE)
-		lane_op_clock_ratio = pll->lanes;
-	else
-		lane_op_clock_ratio = 1;
-	dev_dbg(dev, "lane_op_clock_ratio: %d\n", lane_op_clock_ratio);
-
-	dev_dbg(dev, "binning: %dx%d\n", pll->binning_horizontal,
-		pll->binning_vertical);
-
-	/* CSI transfers 2 bits per clock per lane; thus times 2 */
-	pll->pll_op_clk_freq_hz = pll->link_freq * 2
-		* (pll->lanes / lane_op_clock_ratio);
-
-	/* Figure out limits for pre-pll divider based on extclk */
-	dev_dbg(dev, "min / max pre_pll_clk_div: %d / %d\n",
-		limits->min_pre_pll_clk_div, limits->max_pre_pll_clk_div);
-	limits->max_pre_pll_clk_div =
-		min_t(uint16_t, limits->max_pre_pll_clk_div,
-		      clk_div_even(pll->ext_clk_freq_hz /
-				   limits->min_pll_ip_freq_hz));
-	limits->min_pre_pll_clk_div =
-		max_t(uint16_t, limits->min_pre_pll_clk_div,
-		      clk_div_even_up(
-			      DIV_ROUND_UP(pll->ext_clk_freq_hz,
-					   limits->max_pll_ip_freq_hz)));
-	dev_dbg(dev, "pre-pll check: min / max pre_pll_clk_div: %d / %d\n",
-		limits->min_pre_pll_clk_div, limits->max_pre_pll_clk_div);
-
-	i = gcd(pll->pll_op_clk_freq_hz, pll->ext_clk_freq_hz);
-	mul = div_u64(pll->pll_op_clk_freq_hz, i);
-	div = pll->ext_clk_freq_hz / i;
-	dev_dbg(dev, "mul %d / div %d\n", mul, div);
-
-	limits->min_pre_pll_clk_div =
-		max_t(uint16_t, limits->min_pre_pll_clk_div,
-		      clk_div_even_up(
-			      DIV_ROUND_UP(mul * pll->ext_clk_freq_hz,
-					   limits->max_pll_op_freq_hz)));
-	dev_dbg(dev, "pll_op check: min / max pre_pll_clk_div: %d / %d\n",
-		limits->min_pre_pll_clk_div, limits->max_pre_pll_clk_div);
-
-	if (limits->min_pre_pll_clk_div > limits->max_pre_pll_clk_div) {
-		dev_err(dev, "unable to compute pre_pll divisor\n");
-		return -EINVAL;
-	}
-
-	pll->pre_pll_clk_div = limits->min_pre_pll_clk_div;
-
 	/*
 	 * Get pre_pll_clk_div so that our pll_op_clk_freq_hz won't be
 	 * too high.
@@ -193,8 +145,8 @@ int smiapp_pll_calculate(struct device *dev, struct smiapp_pll_limits *limits,
 		more_mul_min);
 
 	if (more_mul_min > more_mul_max) {
-		dev_warn(dev,
-			 "unable to compute more_mul_min and more_mul_max\n");
+		dev_dbg(dev,
+			"unable to compute more_mul_min and more_mul_max\n");
 		return -EINVAL;
 	}
 
@@ -209,7 +161,7 @@ int smiapp_pll_calculate(struct device *dev, struct smiapp_pll_limits *limits,
 
 	dev_dbg(dev, "final more_mul: %d\n", i);
 	if (i > more_mul_max) {
-		dev_warn(dev, "final more_mul is bad, max %d\n", more_mul_max);
+		dev_dbg(dev, "final more_mul is bad, max %d\n", more_mul_max);
 		return -EINVAL;
 	}
 
@@ -354,8 +306,6 @@ int smiapp_pll_calculate(struct device *dev, struct smiapp_pll_limits *limits,
 	pll->pixel_rate_csi =
 		pll->op_pix_clk_freq_hz * lane_op_clock_ratio;
 
-	print_pll(dev, pll);
-
 	rval = bounds_check(dev, pll->pre_pll_clk_div,
 			    limits->min_pre_pll_clk_div,
 			    limits->max_pre_pll_clk_div, "pre_pll_clk_div");
@@ -411,6 +361,71 @@ int smiapp_pll_calculate(struct device *dev, struct smiapp_pll_limits *limits,
 
 	return rval;
 }
+
+int smiapp_pll_calculate(struct device *dev, struct smiapp_pll_limits *limits,
+			 struct smiapp_pll *pll)
+{
+	uint32_t lane_op_clock_ratio;
+	uint32_t mul, div;
+	unsigned int i;
+	int rval = -EINVAL;
+
+	if (pll->flags & SMIAPP_PLL_FLAG_OP_PIX_CLOCK_PER_LANE)
+		lane_op_clock_ratio = pll->lanes;
+	else
+		lane_op_clock_ratio = 1;
+	dev_dbg(dev, "lane_op_clock_ratio: %d\n", lane_op_clock_ratio);
+
+	dev_dbg(dev, "binning: %dx%d\n", pll->binning_horizontal,
+		pll->binning_vertical);
+
+	/* CSI transfers 2 bits per clock per lane; thus times 2 */
+	pll->pll_op_clk_freq_hz = pll->link_freq * 2
+		* (pll->lanes / lane_op_clock_ratio);
+
+	/* Figure out limits for pre-pll divider based on extclk */
+	dev_dbg(dev, "min / max pre_pll_clk_div: %d / %d\n",
+		limits->min_pre_pll_clk_div, limits->max_pre_pll_clk_div);
+	limits->max_pre_pll_clk_div =
+		min_t(uint16_t, limits->max_pre_pll_clk_div,
+		      clk_div_even(pll->ext_clk_freq_hz /
+				   limits->min_pll_ip_freq_hz));
+	limits->min_pre_pll_clk_div =
+		max_t(uint16_t, limits->min_pre_pll_clk_div,
+		      clk_div_even_up(
+			      DIV_ROUND_UP(pll->ext_clk_freq_hz,
+					   limits->max_pll_ip_freq_hz)));
+	dev_dbg(dev, "pre-pll check: min / max pre_pll_clk_div: %d / %d\n",
+		limits->min_pre_pll_clk_div, limits->max_pre_pll_clk_div);
+
+	i = gcd(pll->pll_op_clk_freq_hz, pll->ext_clk_freq_hz);
+	mul = div_u64(pll->pll_op_clk_freq_hz, i);
+	div = pll->ext_clk_freq_hz / i;
+	dev_dbg(dev, "mul %d / div %d\n", mul, div);
+
+	limits->min_pre_pll_clk_div =
+		max_t(uint16_t, limits->min_pre_pll_clk_div,
+		      clk_div_even_up(
+			      DIV_ROUND_UP(mul * pll->ext_clk_freq_hz,
+					   limits->max_pll_op_freq_hz)));
+	dev_dbg(dev, "pll_op check: min / max pre_pll_clk_div: %d / %d\n",
+		limits->min_pre_pll_clk_div, limits->max_pre_pll_clk_div);
+
+	for (pll->pre_pll_clk_div = limits->min_pre_pll_clk_div;
+	     pll->pre_pll_clk_div <= limits->max_pre_pll_clk_div;
+	     pll->pre_pll_clk_div += 2 - (pll->pre_pll_clk_div & 1)) {
+		rval = __smiapp_pll_calculate(dev, limits, pll, mul, div,
+					      lane_op_clock_ratio);
+		if (rval)
+			continue;
+
+		print_pll(dev, pll);
+		return 0;
+	}
+
+	dev_info(dev, "unable to compute pre_pll divisor\n");
+	return rval;
+}
 EXPORT_SYMBOL_GPL(smiapp_pll_calculate);
 
 MODULE_AUTHOR("Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>");