ata: ahci_brcmstb: enable support for ALPM

Enable support for ALPM in the host controller's capabilities
register. Also adjust the PLL  timeout to give it enough time
to lock when the port exits slumber mode.

tj: minor style updates
Signed-off-by: NDanesh Petigara <dpetigara@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

drivers/ata/ahci_brcmstb.c

@@ -53,6 +53,10 @@
  #define SATA_TOP_CTRL_PHY_OFFS				0x8
  #define SATA_TOP_MAX_PHYS				2
 
+#define SATA_FIRST_PORT_CTRL				0x700
+#define SATA_NEXT_PORT_CTRL_OFFSET			0x80
+#define SATA_PORT_PCTRL6(reg_base)			(reg_base + 0x18)
+
 /* On big-endian MIPS, buses are reversed to big endian, so switch them back */
 #if defined(CONFIG_MIPS) && defined(__BIG_ENDIAN)
 #define DATA_ENDIAN			 2 /* AHCI->DDR inbound accesses */
@@ -111,6 +115,34 @@ static inline void brcm_sata_writereg(u32 val, void __iomem *addr)
 		writel_relaxed(val, addr);
 }
 
+static void brcm_sata_alpm_init(struct ahci_host_priv *hpriv)
+{
+	struct brcm_ahci_priv *priv = hpriv->plat_data;
+	u32 bus_ctrl, port_ctrl, host_caps;
+	int i;
+
+	/* Enable support for ALPM */
+	bus_ctrl = brcm_sata_readreg(priv->top_ctrl +
+				     SATA_TOP_CTRL_BUS_CTRL);
+	brcm_sata_writereg(bus_ctrl | OVERRIDE_HWINIT,
+			   priv->top_ctrl + SATA_TOP_CTRL_BUS_CTRL);
+	host_caps = readl(hpriv->mmio + HOST_CAP);
+	writel(host_caps | HOST_CAP_ALPM, hpriv->mmio);
+	brcm_sata_writereg(bus_ctrl, priv->top_ctrl + SATA_TOP_CTRL_BUS_CTRL);
+
+	/*
+	 * Adjust timeout to allow PLL sufficient time to lock while waking
+	 * up from slumber mode.
+	 */
+	for (i = 0, port_ctrl = SATA_FIRST_PORT_CTRL;
+	     i < SATA_TOP_MAX_PHYS;
+	     i++, port_ctrl += SATA_NEXT_PORT_CTRL_OFFSET) {
+		if (priv->port_mask & BIT(i))
+			writel(0xff1003fc,
+			       hpriv->mmio + SATA_PORT_PCTRL6(port_ctrl));
+	}
+}
+
 static void brcm_sata_phy_enable(struct brcm_ahci_priv *priv, int port)
 {
 	void __iomem *phyctrl = priv->top_ctrl + SATA_TOP_CTRL_PHY_CTRL +
@@ -240,6 +272,7 @@ static int brcm_ahci_resume(struct device *dev)
 
 	brcm_sata_init(priv);
 	brcm_sata_phys_enable(priv);
+	brcm_sata_alpm_init(hpriv);
 	return ahci_platform_resume(dev);
 }
 #endif
@@ -284,6 +317,8 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 		return PTR_ERR(hpriv);
 	hpriv->plat_data = priv;
 
+	brcm_sata_alpm_init(hpriv);
+
 	ret = ahci_platform_enable_resources(hpriv);
 	if (ret)
 		return ret;