md/raid56: Don't perform reads to support writes until stripe is ready.

If it is found that we need to pre-read some blocks before a write
can succeed, we normally set STRIPE_DELAYED and don't actually perform
the read until STRIPE_PREREAD_ACTIVE subsequently gets set.

However for a degraded RAID6 we currently perform the reads as soon
as we see that a write is pending.  This significantly hurts
throughput.

So:
 - when handle_stripe_dirtying find a block that it wants on a device
   that is failed, set STRIPE_DELAY, instead of doing nothing, and
 - when fetch_block detects that a read might be required to satisfy a
   write, only perform the read if STRIPE_PREREAD_ACTIVE is set,
   and if we would actually need to read something to complete the write.

This also helps RAID5, though less often as RAID5 supports a
read-modify-write cycle.  For RAID5 the read is performed too early
only if the write is not a full 4K aligned write (i.e. no an
R5_OVERWRITE).

Also clean up a couple of horrible bits of formatting.
Reported-by: NPatrik Horník <patrik@dsl.sk>
Signed-off-by: NNeilBrown <neilb@suse.de>

drivers/md/raid5.c

@@ -292,9 +292,12 @@ static void do_release_stripe(struct r5conf *conf, struct stripe_head *sh,
 	BUG_ON(atomic_read(&conf->active_stripes)==0);
 	if (test_bit(STRIPE_HANDLE, &sh->state)) {
 		if (test_bit(STRIPE_DELAYED, &sh->state) &&
-		    !test_bit(STRIPE_PREREAD_ACTIVE, &sh->state))
+		    !test_bit(STRIPE_PREREAD_ACTIVE, &sh->state)) {
 			list_add_tail(&sh->lru, &conf->delayed_list);
-		else if (test_bit(STRIPE_BIT_DELAY, &sh->state) &&
+			if (atomic_read(&conf->preread_active_stripes)
+			    < IO_THRESHOLD)
+				md_wakeup_thread(conf->mddev->thread);
+		} else if (test_bit(STRIPE_BIT_DELAY, &sh->state) &&
 			   sh->bm_seq - conf->seq_write > 0)
 			list_add_tail(&sh->lru, &conf->bitmap_list);
 		else {
@@ -2886,8 +2889,11 @@ static int fetch_block(struct stripe_head *sh, struct stripe_head_state *s,
 	     (s->failed >= 1 && fdev[0]->toread) ||
 	     (s->failed >= 2 && fdev[1]->toread) ||
 	     (sh->raid_conf->level <= 5 && s->failed && fdev[0]->towrite &&
+	      (!test_bit(R5_Insync, &dev->flags) || test_bit(STRIPE_PREREAD_ACTIVE, &sh->state)) &&
 	      !test_bit(R5_OVERWRITE, &fdev[0]->flags)) ||
-	     (sh->raid_conf->level == 6 && s->failed && s->to_write))) {
+	     (sh->raid_conf->level == 6 && s->failed && s->to_write &&
+	      s->to_write < sh->raid_conf->raid_disks - 2 &&
+	      (!test_bit(R5_Insync, &dev->flags) || test_bit(STRIPE_PREREAD_ACTIVE, &sh->state))))) {
 		/* we would like to get this block, possibly by computing it,
 		 * otherwise read it if the backing disk is insync
 		 */
@@ -3086,7 +3092,8 @@ static void handle_stripe_dirtying(struct r5conf *conf,
 		    !test_bit(R5_LOCKED, &dev->flags) &&
 		    !(test_bit(R5_UPTODATE, &dev->flags) ||
 		    test_bit(R5_Wantcompute, &dev->flags))) {
-			if (test_bit(R5_Insync, &dev->flags)) rcw++;
+			if (test_bit(R5_Insync, &dev->flags))
+				rcw++;
 			else
 				rcw += 2*disks;
 		}
@@ -3107,10 +3114,10 @@ static void handle_stripe_dirtying(struct r5conf *conf,
 			    !(test_bit(R5_UPTODATE, &dev->flags) ||
 			    test_bit(R5_Wantcompute, &dev->flags)) &&
 			    test_bit(R5_Insync, &dev->flags)) {
-				if (
-				  test_bit(STRIPE_PREREAD_ACTIVE, &sh->state)) {
-					pr_debug("Read_old block "
-						 "%d for r-m-w\n", i);
+				if (test_bit(STRIPE_PREREAD_ACTIVE,
+					     &sh->state)) {
+					pr_debug("Read_old block %d for r-m-w\n",
+						 i);
 					set_bit(R5_LOCKED, &dev->flags);
 					set_bit(R5_Wantread, &dev->flags);
 					s->locked++;
@@ -3133,10 +3140,9 @@ static void handle_stripe_dirtying(struct r5conf *conf,
 			    !(test_bit(R5_UPTODATE, &dev->flags) ||
 			      test_bit(R5_Wantcompute, &dev->flags))) {
 				rcw++;
-				if (!test_bit(R5_Insync, &dev->flags))
-					continue; /* it's a failed drive */
-				if (
-				  test_bit(STRIPE_PREREAD_ACTIVE, &sh->state)) {
+				if (test_bit(R5_Insync, &dev->flags) &&
+				    test_bit(STRIPE_PREREAD_ACTIVE,
+					     &sh->state)) {
 					pr_debug("Read_old block "
 						"%d for Reconstruct\n", i);
 					set_bit(R5_LOCKED, &dev->flags);