pinctrl: Add pinctrl-s3c64xx driver

This patch adds pinctrl-s3c64xx driver which implements pin control
interface for Samsung S3C64xx SoCs.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt

@@ -7,6 +7,7 @@ on-chip controllers onto these pads.
 
 Required Properties:
 - compatible: should be one of the following.
+  - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller,
   - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
   - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
   - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
@@ -105,6 +106,8 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
 
    - compatible: identifies the type of the external wakeup interrupt controller
      The possible values are:
+     - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung S3C64xx SoCs,
      - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
        found on Samsung Exynos4210 SoC.
    - interrupt-parent: phandle of the interrupt parent to which the external

drivers/pinctrl/Kconfig

@@ -208,6 +208,11 @@ config PINCTRL_EXYNOS5440
 	select PINMUX
 	select PINCONF
 
+config PINCTRL_S3C64XX
+	bool "Samsung S3C64XX SoC pinctrl driver"
+	depends on ARCH_S3C64XX
+	select PINCTRL_SAMSUNG
+
 source "drivers/pinctrl/mvebu/Kconfig"
 source "drivers/pinctrl/sh-pfc/Kconfig"
 source "drivers/pinctrl/spear/Kconfig"

drivers/pinctrl/Makefile

@@ -41,6 +41,7 @@ obj-$(CONFIG_PINCTRL_COH901)	+= pinctrl-coh901.o
 obj-$(CONFIG_PINCTRL_SAMSUNG)	+= pinctrl-samsung.o
 obj-$(CONFIG_PINCTRL_EXYNOS)	+= pinctrl-exynos.o
 obj-$(CONFIG_PINCTRL_EXYNOS5440)	+= pinctrl-exynos5440.o
+obj-$(CONFIG_PINCTRL_S3C64XX)	+= pinctrl-s3c64xx.o
 obj-$(CONFIG_PINCTRL_XWAY)	+= pinctrl-xway.o
 obj-$(CONFIG_PINCTRL_LANTIQ)	+= pinctrl-lantiq.o
 

drivers/pinctrl/pinctrl-samsung.c

@@ -970,6 +970,10 @@ static const struct of_device_id samsung_pinctrl_dt_match[] = {
 		.data = (void *)exynos4210_pin_ctrl },
 	{ .compatible = "samsung,exynos4x12-pinctrl",
 		.data = (void *)exynos4x12_pin_ctrl },
+#endif
+#ifdef CONFIG_PINCTRL_S3C64XX
+	{ .compatible = "samsung,s3c64xx-pinctrl",
+		.data = s3c64xx_pin_ctrl },
 #endif
 	{},
 };

drivers/pinctrl/pinctrl-samsung.h

@@ -117,7 +117,9 @@ struct samsung_pin_bank_type {
  * @pctl_offset: starting offset of the pin-bank registers.
  * @pin_base: starting pin number of the bank.
  * @nr_pins: number of pins included in this bank.
+ * @eint_func: function to set in CON register to configure pin as EINT.
  * @eint_type: type of the external interrupt supported by the bank.
+ * @eint_mask: bit mask of pins which support EINT function.
  * @name: name to be prefixed for each pin in this pin bank.
  * @of_node: OF node of the bank.
  * @drvdata: link to controller driver data
@@ -131,7 +133,9 @@ struct samsung_pin_bank {
 	u32		pctl_offset;
 	u32		pin_base;
 	u8		nr_pins;
+	u8		eint_func;
 	enum eint_type	eint_type;
+	u32		eint_mask;
 	u32		eint_offset;
 	char		*name;
 	struct device_node *of_node;
@@ -240,5 +244,6 @@ struct samsung_pmx_func {
 /* list of all exported SoC specific data */
 extern struct samsung_pin_ctrl exynos4210_pin_ctrl[];
 extern struct samsung_pin_ctrl exynos4x12_pin_ctrl[];
+extern struct samsung_pin_ctrl s3c64xx_pin_ctrl[];
 
 #endif /* __PINCTRL_SAMSUNG_H */