Merge branch 'omap-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

arch/arm/mach-omap1/board-nokia770.c

@@ -16,6 +16,8 @@
 
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
+#include <linux/workqueue.h>
+#include <linux/delay.h>
 
 #include <asm/hardware.h>
 #include <asm/mach-types.h>
@@ -103,7 +105,7 @@ static struct ads7846_platform_data nokia770_ads7846_platform_data __initdata =
 
 static struct spi_board_info nokia770_spi_board_info[] __initdata = {
 	[0] = {
-		.modalias       = "lcd_lph8923",
+		.modalias		= "lcd_mipid",
 		.bus_num        = 2,
 		.chip_select    = 3,
 		.max_speed_hz   = 12000000,

arch/arm/mach-omap1/clock.c

@@ -432,8 +432,7 @@ static int omap1_clk_enable(struct clk *clk)
 			}
 
 			if (clk->flags & CLOCK_NO_IDLE_PARENT)
-				if (!cpu_is_omap24xx())
-					omap1_clk_deny_idle(clk->parent);
+				omap1_clk_deny_idle(clk->parent);
 		}
 
 		ret = clk->enable(clk);
@@ -454,8 +453,7 @@ static void omap1_clk_disable(struct clk *clk)
 		if (likely(clk->parent)) {
 			omap1_clk_disable(clk->parent);
 			if (clk->flags & CLOCK_NO_IDLE_PARENT)
-				if (!cpu_is_omap24xx())
-					omap1_clk_allow_idle(clk->parent);
+				omap1_clk_allow_idle(clk->parent);
 		}
 	}
 }
@@ -471,7 +469,7 @@ static int omap1_clk_enable_generic(struct clk *clk)
 	if (unlikely(clk->enable_reg == 0)) {
 		printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
 		       clk->name);
-		return 0;
+		return -EINVAL;
 	}
 
 	if (clk->flags & ENABLE_REG_32BIT) {
@@ -651,10 +649,18 @@ int __init omap1_clk_init(void)
 	int crystal_type = 0; /* Default 12 MHz */
 	u32 reg;
 
+#ifdef CONFIG_DEBUG_LL
+	/* Resets some clocks that may be left on from bootloader,
+	 * but leaves serial clocks on.
+ 	 */
+	omap_writel(0x3 << 29, MOD_CONF_CTRL_0);
+#endif
+
 	/* USB_REQ_EN will be disabled later if necessary (usb_dc_ck) */
 	reg = omap_readw(SOFT_REQ_REG) & (1 << 4);
 	omap_writew(reg, SOFT_REQ_REG);
-	omap_writew(0, SOFT_REQ_REG2);
+	if (!cpu_is_omap15xx())
+		omap_writew(0, SOFT_REQ_REG2);
 
 	clk_init(&omap1_clk_functions);
 
@@ -685,7 +691,7 @@ int __init omap1_clk_init(void)
 
 	info = omap_get_config(OMAP_TAG_CLOCK, struct omap_clock_config);
 	if (info != NULL) {
-		if (!cpu_is_omap1510())
+		if (!cpu_is_omap15xx())
 			crystal_type = info->system_clock_type;
 	}
 

arch/arm/mach-omap1/irq.c

@@ -238,7 +238,7 @@ void __init omap_init_irq(void)
 
 	if (cpu_is_omap730())
 		omap_unmask_irq(INT_730_IH2_IRQ);
-	else if (cpu_is_omap1510())
+	else if (cpu_is_omap15xx())
 		omap_unmask_irq(INT_1510_IH2_IRQ);
 	else if (cpu_is_omap16xx())
 		omap_unmask_irq(INT_1610_IH2_IRQ);

arch/arm/mach-omap1/pm.c

@@ -256,7 +256,8 @@ void omap_pm_suspend(void)
 		tps65010_set_led(LED1, OFF);
 	}
 
-	omap_writew(0xffff, ULPD_SOFT_DISABLE_REQ_REG);
+	if (!cpu_is_omap15xx())
+		omap_writew(0xffff, ULPD_SOFT_DISABLE_REQ_REG);
 
 	/*
 	 * Step 1: turn off interrupts (FIXME: NOTE: already disabled)
@@ -434,7 +435,8 @@ void omap_pm_suspend(void)
 		MPUI1610_RESTORE(OMAP_IH2_3_MIR);
 	}
 
-	omap_writew(0, ULPD_SOFT_DISABLE_REQ_REG);
+	if (!cpu_is_omap15xx())
+		omap_writew(0, ULPD_SOFT_DISABLE_REQ_REG);
 
 	/*
 	 * Reenable interrupts
@@ -704,6 +706,8 @@ static struct pm_ops omap_pm_ops ={
 
 static int __init omap_pm_init(void)
 {
+	int error;
+
 	printk("Power Management for TI OMAP.\n");
 
 	/*
@@ -760,7 +764,9 @@ static int __init omap_pm_init(void)
 	omap_pm_init_proc();
 #endif
 
-	subsys_create_file(&power_subsys, &sleep_while_idle_attr);
+	error = subsys_create_file(&power_subsys, &sleep_while_idle_attr);
+	if (error)
+		printk(KERN_ERR "subsys_create_file failed: %d\n", error);
 
 	if (cpu_is_omap16xx()) {
 		/* configure LOW_PWR pin */

arch/arm/mach-omap1/serial.c

 /*
  * linux/arch/arm/mach-omap1/serial.c
  *
- * OMAP1 CPU identification code
+ * OMAP1 serial support.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -59,7 +59,7 @@ static void __init omap_serial_reset(struct plat_serial8250_port *p)
 	omap_serial_outp(p, UART_OMAP_SCR, 0x08);	/* TX watermark */
 	omap_serial_outp(p, UART_OMAP_MDR1, 0x00);	/* enable UART */
 
-	if (!cpu_is_omap1510()) {
+	if (!cpu_is_omap15xx()) {
 		omap_serial_outp(p, UART_OMAP_SYSC, 0x01);
 		while (!(omap_serial_in(p, UART_OMAP_SYSC) & 0x01));
 	}
@@ -121,7 +121,7 @@ void __init omap_serial_init(void)
 		serial_platform_data[1].irq = INT_730_UART_MODEM_IRDA_2;
 	}
 
-	if (cpu_is_omap1510()) {
+	if (cpu_is_omap15xx()) {
 		serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16;
 		serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16;
 		serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
@@ -147,10 +147,10 @@ void __init omap_serial_init(void)
 				printk("Could not get uart1_ck\n");
 			else {
 				clk_enable(uart1_ck);
-				if (cpu_is_omap1510())
+				if (cpu_is_omap15xx())
 					clk_set_rate(uart1_ck, 12000000);
 			}
-			if (cpu_is_omap1510()) {
+			if (cpu_is_omap15xx()) {
 				omap_cfg_reg(UART1_TX);
 				omap_cfg_reg(UART1_RTS);
 				if (machine_is_omap_innovator()) {
@@ -167,12 +167,12 @@ void __init omap_serial_init(void)
 				printk("Could not get uart2_ck\n");
 			else {
 				clk_enable(uart2_ck);
-				if (cpu_is_omap1510())
+				if (cpu_is_omap15xx())
 					clk_set_rate(uart2_ck, 12000000);
 				else
 					clk_set_rate(uart2_ck, 48000000);
 			}
-			if (cpu_is_omap1510()) {
+			if (cpu_is_omap15xx()) {
 				omap_cfg_reg(UART2_TX);
 				omap_cfg_reg(UART2_RTS);
 				if (machine_is_omap_innovator()) {
@@ -189,10 +189,10 @@ void __init omap_serial_init(void)
 				printk("Could not get uart3_ck\n");
 			else {
 				clk_enable(uart3_ck);
-				if (cpu_is_omap1510())
+				if (cpu_is_omap15xx())
 					clk_set_rate(uart3_ck, 12000000);
 			}
-			if (cpu_is_omap1510()) {
+			if (cpu_is_omap15xx()) {
 				omap_cfg_reg(UART3_TX);
 				omap_cfg_reg(UART3_RX);
 			}

arch/arm/mach-omap2/board-h4.c

@@ -39,7 +39,6 @@
 #include "prcm-regs.h"
 
 #include <asm/io.h>
-#include <asm/delay.h>
 
 static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 };
 static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 };
@@ -179,9 +178,11 @@ static int h4_select_irda(struct device *dev, int state)
 	return err;
 }
 
-static void set_trans_mode(void *data)
+static void set_trans_mode(struct work_struct *work)
 {
-	int *mode = data;
+	struct omap_irda_config *irda_config =
+		container_of(work, struct omap_irda_config, gpio_expa.work);
+	int mode = irda_config->mode;
 	unsigned char expa;
 	int err = 0;
 
@@ -191,7 +192,7 @@ static void set_trans_mode(void *data)
 
 	expa &= ~0x01;
 
-	if (!(*mode & IR_SIRMODE)) { /* MIR/FIR */
+	if (!(mode & IR_SIRMODE)) { /* MIR/FIR */
 		expa |= 0x01;
 	}
 
@@ -204,9 +205,9 @@ static int h4_transceiver_mode(struct device *dev, int mode)
 {
 	struct omap_irda_config *irda_config = dev->platform_data;
 
+	irda_config->mode = mode;
 	cancel_delayed_work(&irda_config->gpio_expa);
-	PREPARE_WORK(&irda_config->gpio_expa, set_trans_mode, &mode);
-#error this is not permitted - mode is an argument variable
+	PREPARE_DELAYED_WORK(&irda_config->gpio_expa, set_trans_mode);
 	schedule_delayed_work(&irda_config->gpio_expa, 0);
 
 	return 0;

arch/arm/mach-omap2/timer-gp.c

@@ -24,6 +24,7 @@
 #include <linux/err.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/irq.h>
 
 #include <asm/mach/time.h>
 #include <asm/arch/dmtimer.h>
@@ -64,7 +65,7 @@ static void __init omap2_gp_timer_init(void)
 	BUG_ON(gptimer == NULL);
 
 	omap_dm_timer_set_source(gptimer, OMAP_TIMER_SRC_SYS_CLK);
-	tick_period = clk_get_rate(omap_dm_timer_get_fclk(gptimer)) / 100;
+	tick_period = clk_get_rate(omap_dm_timer_get_fclk(gptimer)) / HZ;
 	tick_period -= 1;
 
 	setup_irq(omap_dm_timer_get_irq(gptimer), &omap2_gp_timer_irq);

arch/arm/plat-omap/dma.c

@@ -557,7 +557,7 @@ int omap_request_dma(int dev_id, const char *dev_name,
 		omap_enable_channel_irq(free_ch);
 		/* Clear the CSR register and IRQ status register */
 		OMAP_DMA_CSR_REG(free_ch) = OMAP2_DMA_CSR_CLEAR_MASK;
-		omap_writel(~0x0, OMAP_DMA4_IRQSTATUS_L0);
+		omap_writel(1 << free_ch, OMAP_DMA4_IRQSTATUS_L0);
 	}
 
 	*dma_ch_out = free_ch;
@@ -597,10 +597,7 @@ void omap_free_dma(int lch)
 
 		/* Clear the CSR register and IRQ status register */
 		OMAP_DMA_CSR_REG(lch) = OMAP2_DMA_CSR_CLEAR_MASK;
-
-		val = omap_readl(OMAP_DMA4_IRQSTATUS_L0);
-		val |= 1 << lch;
-		omap_writel(val, OMAP_DMA4_IRQSTATUS_L0);
+		omap_writel(1 << lch, OMAP_DMA4_IRQSTATUS_L0);
 
 		/* Disable all DMA interrupts for the channel. */
 		OMAP_DMA_CICR_REG(lch) = 0;
@@ -927,7 +924,6 @@ static irqreturn_t omap1_dma_irq_handler(int irq, void *dev_id)
 static int omap2_dma_handle_ch(int ch)
 {
 	u32 status = OMAP_DMA_CSR_REG(ch);
-	u32 val;
 
 	if (!status)
 		return 0;
@@ -948,11 +944,7 @@ static int omap2_dma_handle_ch(int ch)
 		       dma_chan[ch].dev_id);
 
 	OMAP_DMA_CSR_REG(ch) = OMAP2_DMA_CSR_CLEAR_MASK;
-
-	val = omap_readl(OMAP_DMA4_IRQSTATUS_L0);
-	/* ch in this function is from 0-31 while in register it is 1-32 */
-	val = 1 << (ch);
-	omap_writel(val, OMAP_DMA4_IRQSTATUS_L0);
+	omap_writel(1 << ch, OMAP_DMA4_IRQSTATUS_L0);
 
 	if (likely(dma_chan[ch].callback != NULL))
 		dma_chan[ch].callback(ch, status, dma_chan[ch].data);

arch/arm/plat-omap/dmtimer.c

@@ -90,8 +90,8 @@ static struct omap_dm_timer dm_timers[] = {
 	{ .phys_base = 0xfffb2c00, .irq = INT_1610_GPTIMER4 },
 	{ .phys_base = 0xfffb3400, .irq = INT_1610_GPTIMER5 },
 	{ .phys_base = 0xfffb3c00, .irq = INT_1610_GPTIMER6 },
-	{ .phys_base = 0xfffb4400, .irq = INT_1610_GPTIMER7 },
-	{ .phys_base = 0xfffb4c00, .irq = INT_1610_GPTIMER8 },
+	{ .phys_base = 0xfffb7400, .irq = INT_1610_GPTIMER7 },
+	{ .phys_base = 0xfffbd400, .irq = INT_1610_GPTIMER8 },
 };
 
 #elif defined(CONFIG_ARCH_OMAP2)
@@ -314,6 +314,8 @@ struct clk *omap_dm_timer_get_fclk(struct omap_dm_timer *timer)
 __u32 omap_dm_timer_modify_idlect_mask(__u32 inputmask)
 {
 	BUG();
+
+	return 0;
 }
 
 #endif

arch/arm/plat-omap/gpio.c

@@ -974,10 +974,11 @@ static struct irq_chip gpio_irq_chip = {
 };
 
 static struct irq_chip mpuio_irq_chip = {
-	.name	= "MPUIO",
-	.ack	= mpuio_ack_irq,
-	.mask	= mpuio_mask_irq,
-	.unmask	= mpuio_unmask_irq
+	.name	  = "MPUIO",
+	.ack	  = mpuio_ack_irq,
+	.mask	  = mpuio_mask_irq,
+	.unmask	  = mpuio_unmask_irq,
+	.set_type = gpio_irq_type,
 };
 
 static int initialized;

arch/arm/plat-omap/mcbsp.c

@@ -20,8 +20,8 @@
 #include <linux/interrupt.h>
 #include <linux/err.h>
 #include <linux/clk.h>
+#include <linux/delay.h>
 
-#include <asm/delay.h>
 #include <asm/io.h>
 #include <asm/irq.h>
 

arch/arm/plat-omap/mux.c

@@ -116,7 +116,7 @@ int __init_or_module omap_cfg_reg(const unsigned long index)
 	}
 
 	/* Check for pull up or pull down selection on 1610 */
-	if (!cpu_is_omap1510()) {
+	if (!cpu_is_omap15xx()) {
 		if (cfg->pu_pd_reg && cfg->pull_val) {
 			spin_lock_irqsave(&mux_spin_lock, flags);
 			pu_pd_orig = omap_readl(cfg->pu_pd_reg);
@@ -172,7 +172,7 @@ int __init_or_module omap_cfg_reg(const unsigned long index)
 		printk("      %s (0x%08x) = 0x%08x -> 0x%08x\n",
 		       cfg->mux_reg_name, cfg->mux_reg, reg_orig, reg);
 
-		if (!cpu_is_omap1510()) {
+		if (!cpu_is_omap15xx()) {
 			if (cfg->pu_pd_reg && cfg->pull_val) {
 				printk("      %s (0x%08x) = 0x%08x -> 0x%08x\n",
 				       cfg->pu_pd_name, cfg->pu_pd_reg,

include/asm-arm/arch-omap/entry-macro.S

@@ -61,6 +61,12 @@
 		.macro	disable_fiq
 		.endm
 
+		.macro  get_irqnr_preamble, base, tmp
+		.endm
+
+		.macro  arch_ret_to_user, tmp1, tmp2
+		.endm
+
 		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
 		ldr	\base, =VA_IC_BASE
 		ldr	\irqnr, [\base, #0x98] /* IRQ pending reg 1 */

include/asm-arm/arch-omap/memory.h

@@ -70,7 +70,7 @@
 
 #define virt_to_lbus(x)		((x) - PAGE_OFFSET + OMAP1510_LB_OFFSET)
 #define lbus_to_virt(x)		((x) - OMAP1510_LB_OFFSET + PAGE_OFFSET)
-#define is_lbus_device(dev)	(cpu_is_omap1510() && dev && (strncmp(dev->bus_id, "ohci", 4) == 0))
+#define is_lbus_device(dev)	(cpu_is_omap15xx() && dev && (strncmp(dev->bus_id, "ohci", 4) == 0))
 
 #define __arch_page_to_dma(dev, page)	({is_lbus_device(dev) ? \
 					(dma_addr_t)virt_to_lbus(page_address(page)) : \

include/asm-arm/arch-omap/omap-alsa.h

@@ -65,7 +65,7 @@ struct audio_stream {
 	int period;		/* current transfer period */
 	int periods;		/* current count of periods registerd in the DMA engine */
 	spinlock_t dma_lock;	/* for locking in DMA operations */
-	snd_pcm_substream_t *stream;	/* the pcm stream */
+	struct snd_pcm_substream *stream;	/* the pcm stream */
 	unsigned linked:1;	/* dma channels linked */
 	int offset;		/* store start position of the last period in the alsa buffer */
 	int (*hw_start)(void);  /* interface to start HW interface, e.g. McBSP */
@@ -76,8 +76,8 @@ struct audio_stream {
  * Alsa card structure for aic23
  */
 struct snd_card_omap_codec {
-	snd_card_t *card;
-	snd_pcm_t *pcm;
+	struct snd_card *card;
+	struct snd_pcm *pcm;
 	long samplerate;
 	struct audio_stream s[2];	/* playback & capture */
 };
@@ -89,9 +89,9 @@ struct snd_card_omap_codec {
 struct omap_alsa_codec_config {
 	char 	*name;
 	struct	omap_mcbsp_reg_cfg *mcbsp_regs_alsa;
-	snd_pcm_hw_constraint_list_t *hw_constraints_rates;
-	snd_pcm_hardware_t *snd_omap_alsa_playback;
-	snd_pcm_hardware_t *snd_omap_alsa_capture;
+	struct	snd_pcm_hw_constraint_list *hw_constraints_rates;
+	struct	snd_pcm_hardware *snd_omap_alsa_playback;
+	struct	snd_pcm_hardware *snd_omap_alsa_capture;
 	void	(*codec_configure_dev)(void);
 	void	(*codec_set_samplerate)(long);
 	void	(*codec_clock_setup)(void);