Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (97 commits) [SCSI] zfcp: removed wrong comment [SCSI] zfcp: use of uninitialized variable [SCSI] zfcp: Invalid locking order [SCSI] aic79xx: use dma_get_required_mask() [SCSI] aic79xx: fix bracket mismatch in unused macro [SCSI] BusLogic: Replace 'boolean' by 'bool' [SCSI] advansys: clean up warnings [SCSI] 53c7xx: brackets fix in uncompiled code [SCSI] nsp_cs: remove old scsi code [SCSI] aic79xx: make ahd_match_scb() static [SCSI] DAC960: kmalloc->kzalloc/Casting cleanups [SCSI] scsi_kmap_atomic_sg(): check that local irqs are disabled [SCSI] Buslogic: local_irq_disable() is redundant after local_irq_save() [SCSI] aic94xx: update for v28 firmware [SCSI] scsi_error: Fix lost EH commands [SCSI] aic94xx: Add default bus reset handler [SCSI] aic94xx: Remove TMF result code munging [SCSI] libsas: Add an LU reset mechanism to the error handler [SCSI] libsas: Don't BUG when connecting two expanders via wide port [SCSI] st: fix Tape dies if wrong block size used, bug 7919 ...

Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (97 commits) [SCSI] zfcp: removed wrong comment [SCSI] zfcp: use of uninitialized variable [SCSI] zfcp: Invalid locking order [SCSI] aic79xx: use dma_get_required_mask() [SCSI] aic79xx: fix bracket mismatch in unused macro [SCSI] BusLogic: Replace 'boolean' by 'bool' [SCSI] advansys: clean up warnings [SCSI] 53c7xx: brackets fix in uncompiled code [SCSI] nsp_cs: remove old scsi code [SCSI] aic79xx: make ahd_match_scb() static [SCSI] DAC960: kmalloc->kzalloc/Casting cleanups [SCSI] scsi_kmap_atomic_sg(): check that local irqs are disabled [SCSI] Buslogic: local_irq_disable() is redundant after local_irq_save() [SCSI] aic94xx: update for v28 firmware [SCSI] scsi_error: Fix lost EH commands [SCSI] aic94xx: Add default bus reset handler [SCSI] aic94xx: Remove TMF result code munging [SCSI] libsas: Add an LU reset mechanism to the error handler [SCSI] libsas: Don't BUG when connecting two expanders via wide port [SCSI] st: fix Tape dies if wrong block size used, bug 7919 ...
5f0b1437 · Linus Torvalds · 574009c1 · 81b7bbd1 · 5f0b1437 · 5f0b1437
104 changed file
--- a/Documentation/scsi/ChangeLog.megaraid
+++ b/Documentation/scsi/ChangeLog.megaraid
+Release Date	: Thu Nov 16 15:32:35 EST 2006 -
+				Sumant Patro <sumant.patro@lsi.com>
+Current Version : 2.20.5.1 (scsi module), 2.20.2.6 (cmm module)
+Older Version	: 2.20.4.9 (scsi module), 2.20.2.6 (cmm module)
+
+1.	Changes in Initialization to fix kdump failure.
+	Send SYNC command on loading.
+	This command clears the pending commands in the adapter
+	and re-initialize its internal RAID structure.
+	Without this change, megaraid driver either panics or fails to
+	initialize the adapter during kdump's second kernel boot
+	if there are pending commands or interrupts from other devices
+	sharing the same IRQ.
+2. 	Authors email-id domain name changed from lsil.com to lsi.com.
+	Also modified the MODULE_AUTHOR to megaraidlinux@lsi.com
+
 Release Date	: Fri May 19 09:31:45 EST 2006 - Seokmann Ju <sju@lsil.com>
 Current Version : 2.20.4.9 (scsi module), 2.20.2.6 (cmm module)
 Older Version	: 2.20.4.8 (scsi module), 2.20.2.6 (cmm module)

--- a/drivers/block/DAC960.c
+++ b/drivers/block/DAC960.c
@@ -1373,8 +1373,7 @@ static bool DAC960_V2_EnableMemoryMailboxInterface(DAC960_Controller_T
  Controller->BounceBufferLimit = DAC690_V2_PciDmaMask;

  /* This is a temporary dma mapping, used only in the scope of this function */
-  CommandMailbox =
-	  (DAC960_V2_CommandMailbox_T *)pci_alloc_consistent( PCI_Device,
+  CommandMailbox = pci_alloc_consistent(PCI_Device,
 		sizeof(DAC960_V2_CommandMailbox_T), &CommandMailboxDMA);
  if (CommandMailbox == NULL)
 	  return false;
@@ -1879,8 +1878,8 @@ static bool DAC960_V2_ReadControllerConfiguration(DAC960_Controller_T
      if (NewLogicalDeviceInfo->LogicalDeviceState !=
 	  DAC960_V2_LogicalDevice_Offline)
 	Controller->LogicalDriveInitiallyAccessible[LogicalDeviceNumber] = true;
-      LogicalDeviceInfo = (DAC960_V2_LogicalDeviceInfo_T *)
-	kmalloc(sizeof(DAC960_V2_LogicalDeviceInfo_T), GFP_ATOMIC);
+      LogicalDeviceInfo = kmalloc(sizeof(DAC960_V2_LogicalDeviceInfo_T),
+				   GFP_ATOMIC);
      if (LogicalDeviceInfo == NULL)
 	return DAC960_Failure(Controller, "LOGICAL DEVICE ALLOCATION");
      Controller->V2.LogicalDeviceInformation[LogicalDeviceNumber] =
@@ -2113,8 +2112,8 @@ static bool DAC960_V2_ReadDeviceConfiguration(DAC960_Controller_T
      if (!DAC960_V2_NewPhysicalDeviceInfo(Controller, Channel, TargetID, LogicalUnit))
 	  break;

-      PhysicalDeviceInfo = (DAC960_V2_PhysicalDeviceInfo_T *)
-		kmalloc(sizeof(DAC960_V2_PhysicalDeviceInfo_T), GFP_ATOMIC);
+      PhysicalDeviceInfo = kmalloc(sizeof(DAC960_V2_PhysicalDeviceInfo_T),
+				    GFP_ATOMIC);
      if (PhysicalDeviceInfo == NULL)
 		return DAC960_Failure(Controller, "PHYSICAL DEVICE ALLOCATION");
      Controller->V2.PhysicalDeviceInformation[PhysicalDeviceIndex] =
@@ -2122,8 +2121,8 @@ static bool DAC960_V2_ReadDeviceConfiguration(DAC960_Controller_T
      memcpy(PhysicalDeviceInfo, NewPhysicalDeviceInfo,
 		sizeof(DAC960_V2_PhysicalDeviceInfo_T));

-      InquiryUnitSerialNumber = (DAC960_SCSI_Inquiry_UnitSerialNumber_T *)
-	kmalloc(sizeof(DAC960_SCSI_Inquiry_UnitSerialNumber_T), GFP_ATOMIC);
+      InquiryUnitSerialNumber = kmalloc(
+	      sizeof(DAC960_SCSI_Inquiry_UnitSerialNumber_T), GFP_ATOMIC);
      if (InquiryUnitSerialNumber == NULL) {
 	kfree(PhysicalDeviceInfo);
 	return DAC960_Failure(Controller, "SERIAL NUMBER ALLOCATION");
@@ -4949,8 +4948,8 @@ static void DAC960_V2_ProcessCompletedCommand(DAC960_Command_T *Command)
 	      PhysicalDevice.LogicalUnit = NewLogicalDeviceInfo->LogicalUnit;
 	      Controller->V2.LogicalDriveToVirtualDevice[LogicalDeviceNumber] =
 		PhysicalDevice;
-	      LogicalDeviceInfo = (DAC960_V2_LogicalDeviceInfo_T *)
-		kmalloc(sizeof(DAC960_V2_LogicalDeviceInfo_T), GFP_ATOMIC);
+	      LogicalDeviceInfo = kmalloc(sizeof(DAC960_V2_LogicalDeviceInfo_T),
+					  GFP_ATOMIC);
 	      Controller->V2.LogicalDeviceInformation[LogicalDeviceNumber] =
 		LogicalDeviceInfo;
 	      DAC960_Critical("Logical Drive %d (/dev/rd/c%dd%d) "
@@ -5709,14 +5708,14 @@ static bool DAC960_CheckStatusBuffer(DAC960_Controller_T *Controller,
      unsigned int NewStatusBufferLength = DAC960_InitialStatusBufferSize;
      while (NewStatusBufferLength < ByteCount)
 	NewStatusBufferLength *= 2;
-      Controller->CombinedStatusBuffer =
-	(unsigned char *) kmalloc(NewStatusBufferLength, GFP_ATOMIC);
+      Controller->CombinedStatusBuffer = kmalloc(NewStatusBufferLength,
+						  GFP_ATOMIC);
      if (Controller->CombinedStatusBuffer == NULL) return false;
      Controller->CombinedStatusBufferLength = NewStatusBufferLength;
      return true;
    }
-  NewStatusBuffer = (unsigned char *)
-    kmalloc(2 * Controller->CombinedStatusBufferLength, GFP_ATOMIC);
+  NewStatusBuffer = kmalloc(2 * Controller->CombinedStatusBufferLength,
+			     GFP_ATOMIC);
  if (NewStatusBuffer == NULL)
    {
      DAC960_Warning("Unable to expand Combined Status Buffer - Truncating\n",

--- a/drivers/message/fusion/Kconfig
+++ b/drivers/message/fusion/Kconfig
@@ -66,7 +66,7 @@ config FUSION_MAX_SGE

 config FUSION_CTL
 	tristate "Fusion MPT misc device (ioctl) driver"
-	depends on FUSION_SPI || FUSION_FC
+	depends on FUSION_SPI || FUSION_FC || FUSION_SAS
 	---help---
 	  The Fusion MPT misc device driver provides specialized control
 	  of MPT adapters via system ioctl calls.  Use of ioctl calls to

--- a/drivers/message/fusion/Makefile
+++ b/drivers/message/fusion/Makefile
@@ -8,6 +8,9 @@
 #EXTRA_CFLAGS += -DMPT_DEBUG_INIT
 #EXTRA_CFLAGS += -DMPT_DEBUG_EXIT
 #EXTRA_CFLAGS += -DMPT_DEBUG_FAIL
+#EXTRA_CFLAGS += -DMPT_DEBUG_DV
+#EXTRA_CFLAGS += -DMPT_DEBUG_TM
+#EXTRA_CFLAGS += -DMPT_DEBUG_REPLY

 #
 # driver/module specifics...
@@ -20,11 +23,7 @@
 #CFLAGS_mptbase.o += -DMPT_DEBUG_RESET
 #
 #  For mptscsih:
-#CFLAGS_mptscsih.o += -DMPT_DEBUG_DV
-#CFLAGS_mptscsih.o += -DMPT_DEBUG_NEGO
-#CFLAGS_mptscsih.o += -DMPT_DEBUG_TM
 #CFLAGS_mptscsih.o += -DMPT_DEBUG_SCSI
-#CFLAGS_mptscsih.o += -DMPT_DEBUG_REPLY
 #
 #  For mptctl:
 #CFLAGS_mptctl.o += -DMPT_DEBUG_IOCTL

--- a/drivers/message/fusion/lsi/mpi.h
+++ b/drivers/message/fusion/lsi/mpi.h
 /*
- *  Copyright (c) 2000-2005 LSI Logic Corporation.
+ *  Copyright (c) 2000-2006 LSI Logic Corporation.
 *
 *
 *           Name:  mpi.h
 *          Title:  MPI Message independent structures and definitions
 *  Creation Date:  July 27, 2000
 *
- *    mpi.h Version:  01.05.11
+ *    mpi.h Version:  01.05.12
 *
 *  Version History
 *  ---------------
@@ -77,6 +77,7 @@
 *  08-03-05  01.05.09  Bumped MPI_HEADER_VERSION_UNIT.
 *  08-30-05  01.05.10  Added 2 new IOCStatus codes for Target.
 *  03-27-06  01.05.11  Bumped MPI_HEADER_VERSION_UNIT.
+ *  10-11-06  01.05.12  Bumped MPI_HEADER_VERSION_UNIT.
 *  --------------------------------------------------------------------------
 */

@@ -107,7 +108,7 @@
 /* Note: The major versions of 0xe0 through 0xff are reserved */

 /* versioning for this MPI header set */
-#define MPI_HEADER_VERSION_UNIT             (0x0D)
+#define MPI_HEADER_VERSION_UNIT             (0x0E)
 #define MPI_HEADER_VERSION_DEV              (0x00)
 #define MPI_HEADER_VERSION_UNIT_MASK        (0xFF00)
 #define MPI_HEADER_VERSION_UNIT_SHIFT       (8)

--- a/drivers/message/fusion/lsi/mpi_cnfg.h
+++ b/drivers/message/fusion/lsi/mpi_cnfg.h
 /*
- *  Copyright (c) 2000-2005 LSI Logic Corporation.
+ *  Copyright (c) 2000-2006 LSI Logic Corporation.
 *
 *
 *           Name:  mpi_cnfg.h
 *          Title:  MPI Config message, structures, and Pages
 *  Creation Date:  July 27, 2000
 *
- *    mpi_cnfg.h Version:  01.05.12
+ *    mpi_cnfg.h Version:  01.05.13
 *
 *  Version History
 *  ---------------
@@ -276,6 +276,23 @@
 *                      Added AdditionalControlFlags, MaxTargetPortConnectTime,
 *                      ReportDeviceMissingDelay, and IODeviceMissingDelay
 *                      fields to SAS IO Unit Page 1.
+ *  10-11-06  01.05.13  Added NumForceWWID field and ForceWWID array to
+ *                      Manufacturing Page 5.
+ *                      Added Manufacturing pages 8 through 10.
+ *                      Added defines for supported metadata size bits in
+ *                      CapabilitiesFlags field of IOC Page 6.
+ *                      Added defines for metadata size bits in VolumeSettings
+ *                      field of RAID Volume Page 0.
+ *                      Added SATA Link Reset settings, Enable SATA Asynchronous
+ *                      Notification bit, and HideNonZeroAttachedPhyIdentifiers
+ *                      bit to AdditionalControlFlags field of SAS IO Unit
+ *                      Page 1.
+ *                      Added defines for Enclosure Devices Unmapped and
+ *                      Device Limit Exceeded bits in Status field of SAS IO
+ *                      Unit Page 2.
+ *                      Added more AccessStatus values for SAS Device Page 0.
+ *                      Added bit for SATA Asynchronous Notification Support in
+ *                      Flags field of SAS Device Page 0.
 *  --------------------------------------------------------------------------
 */

@@ -654,17 +671,24 @@ typedef struct _CONFIG_PAGE_MANUFACTURING_4
 #define MPI_MANPAGE4_IR_NO_MIX_SAS_SATA                 (0x01)


+#ifndef MPI_MANPAGE5_NUM_FORCEWWID
+#define MPI_MANPAGE5_NUM_FORCEWWID      (1)
+#endif
+
 typedef struct _CONFIG_PAGE_MANUFACTURING_5
 {
    CONFIG_PAGE_HEADER              Header;             /* 00h */
    U64                             BaseWWID;           /* 04h */
    U8                              Flags;              /* 0Ch */
-    U8                              Reserved1;          /* 0Dh */
+    U8                              NumForceWWID;       /* 0Dh */
    U16                             Reserved2;          /* 0Eh */
+    U32                             Reserved3;          /* 10h */
+    U32                             Reserved4;          /* 14h */
+    U64                             ForceWWID[MPI_MANPAGE5_NUM_FORCEWWID]; /* 18h */
 } CONFIG_PAGE_MANUFACTURING_5, MPI_POINTER PTR_CONFIG_PAGE_MANUFACTURING_5,
  ManufacturingPage5_t, MPI_POINTER pManufacturingPage5_t;

-#define MPI_MANUFACTURING5_PAGEVERSION                  (0x01)
+#define MPI_MANUFACTURING5_PAGEVERSION                  (0x02)

 /* defines for the Flags field */
 #define MPI_MANPAGE5_TWO_WWID_PER_PHY                   (0x01)
@@ -740,6 +764,36 @@ typedef struct _CONFIG_PAGE_MANUFACTURING_7
 #define MPI_MANPAGE7_FLAG_USE_SLOT_INFO                 (0x00000001)


+typedef struct _CONFIG_PAGE_MANUFACTURING_8
+{
+    CONFIG_PAGE_HEADER              Header;             /* 00h */
+    U32                             ProductSpecificInfo;/* 04h */
+} CONFIG_PAGE_MANUFACTURING_8, MPI_POINTER PTR_CONFIG_PAGE_MANUFACTURING_8,
+  ManufacturingPage8_t, MPI_POINTER pManufacturingPage8_t;
+
+#define MPI_MANUFACTURING8_PAGEVERSION                  (0x00)
+
+
+typedef struct _CONFIG_PAGE_MANUFACTURING_9
+{
+    CONFIG_PAGE_HEADER              Header;             /* 00h */
+    U32                             ProductSpecificInfo;/* 04h */
+} CONFIG_PAGE_MANUFACTURING_9, MPI_POINTER PTR_CONFIG_PAGE_MANUFACTURING_9,
+  ManufacturingPage9_t, MPI_POINTER pManufacturingPage9_t;
+
+#define MPI_MANUFACTURING6_PAGEVERSION                  (0x00)
+
+
+typedef struct _CONFIG_PAGE_MANUFACTURING_10
+{
+    CONFIG_PAGE_HEADER              Header;             /* 00h */
+    U32                             ProductSpecificInfo;/* 04h */
+} CONFIG_PAGE_MANUFACTURING_10, MPI_POINTER PTR_CONFIG_PAGE_MANUFACTURING_10,
+  ManufacturingPage10_t, MPI_POINTER pManufacturingPage10_t;
+
+#define MPI_MANUFACTURING10_PAGEVERSION                 (0x00)
+
+
 /****************************************************************************
 *   IO Unit Config Pages
 ****************************************************************************/
@@ -1080,10 +1134,14 @@ typedef struct _CONFIG_PAGE_IOC_6
 } CONFIG_PAGE_IOC_6, MPI_POINTER PTR_CONFIG_PAGE_IOC_6,
  IOCPage6_t, MPI_POINTER pIOCPage6_t;

-#define MPI_IOCPAGE6_PAGEVERSION                        (0x00)
+#define MPI_IOCPAGE6_PAGEVERSION                        (0x01)

 /* IOC Page 6 Capabilities Flags */

+#define MPI_IOCPAGE6_CAP_FLAGS_MASK_METADATA_SIZE       (0x00000006)
+#define MPI_IOCPAGE6_CAP_FLAGS_64MB_METADATA_SIZE       (0x00000000)
+#define MPI_IOCPAGE6_CAP_FLAGS_512MB_METADATA_SIZE      (0x00000002)
+
 #define MPI_IOCPAGE6_CAP_FLAGS_GLOBAL_HOT_SPARE         (0x00000001)


@@ -2160,6 +2218,11 @@ typedef struct _RAID_VOL0_SETTINGS
 #define MPI_RAIDVOL0_SETTING_AUTO_CONFIGURE             (0x0004)
 #define MPI_RAIDVOL0_SETTING_PRIORITY_RESYNC            (0x0008)
 #define MPI_RAIDVOL0_SETTING_FAST_DATA_SCRUBBING_0102   (0x0020) /* obsolete */
+
+#define MPI_RAIDVOL0_SETTING_MASK_METADATA_SIZE         (0x00C0)
+#define MPI_RAIDVOL0_SETTING_64MB_METADATA_SIZE         (0x0000)
+#define MPI_RAIDVOL0_SETTING_512MB_METADATA_SIZE        (0x0040)
+
 #define MPI_RAIDVOL0_SETTING_USE_PRODUCT_ID_SUFFIX      (0x0010)
 #define MPI_RAIDVOL0_SETTING_USE_DEFAULTS               (0x8000)

@@ -2203,7 +2266,7 @@ typedef struct _CONFIG_PAGE_RAID_VOL_0
 } CONFIG_PAGE_RAID_VOL_0, MPI_POINTER PTR_CONFIG_PAGE_RAID_VOL_0,
  RaidVolumePage0_t, MPI_POINTER pRaidVolumePage0_t;

-#define MPI_RAIDVOLPAGE0_PAGEVERSION                    (0x06)
+#define MPI_RAIDVOLPAGE0_PAGEVERSION                    (0x07)

 /* values for RAID Volume Page 0 InactiveStatus field */
 #define MPI_RAIDVOLPAGE0_UNKNOWN_INACTIVE               (0x00)
@@ -2518,7 +2581,7 @@ typedef struct _CONFIG_PAGE_SAS_IO_UNIT_1
 } CONFIG_PAGE_SAS_IO_UNIT_1, MPI_POINTER PTR_CONFIG_PAGE_SAS_IO_UNIT_1,
  SasIOUnitPage1_t, MPI_POINTER pSasIOUnitPage1_t;

-#define MPI_SASIOUNITPAGE1_PAGEVERSION      (0x06)
+#define MPI_SASIOUNITPAGE1_PAGEVERSION      (0x07)

 /* values for SAS IO Unit Page 1 ControlFlags */
 #define MPI_SAS_IOUNIT1_CONTROL_DEVICE_SELF_TEST            (0x8000)
@@ -2544,7 +2607,13 @@ typedef struct _CONFIG_PAGE_SAS_IO_UNIT_1
 #define MPI_SAS_IOUNIT1_CONTROL_CLEAR_AFFILIATION           (0x0001)

 /* values for SAS IO Unit Page 1 AdditionalControlFlags */
-#define MPI_SAS_IOUNIT1_ACONTROL_ALLOW_TABLE_TO_TABLE       (0x0001)
+#define MPI_SAS_IOUNIT1_ACONTROL_SATA_ASYNCHROUNOUS_NOTIFICATION    (0x0040)
+#define MPI_SAS_IOUNIT1_ACONTROL_HIDE_NONZERO_ATTACHED_PHY_IDENT    (0x0020)
+#define MPI_SAS_IOUNIT1_ACONTROL_PORT_ENABLE_ONLY_SATA_LINK_RESET   (0x0010)
+#define MPI_SAS_IOUNIT1_ACONTROL_OTHER_AFFILIATION_SATA_LINK_RESET  (0x0008)
+#define MPI_SAS_IOUNIT1_ACONTROL_SELF_AFFILIATION_SATA_LINK_RESET   (0x0004)
+#define MPI_SAS_IOUNIT1_ACONTROL_NO_AFFILIATION_SATA_LINK_RESET     (0x0002)
+#define MPI_SAS_IOUNIT1_ACONTROL_ALLOW_TABLE_TO_TABLE               (0x0001)

 /* defines for SAS IO Unit Page 1 ReportDeviceMissingDelay */
 #define MPI_SAS_IOUNIT1_REPORT_MISSING_TIMEOUT_MASK         (0x7F)
@@ -2585,9 +2654,11 @@ typedef struct _CONFIG_PAGE_SAS_IO_UNIT_2
 } CONFIG_PAGE_SAS_IO_UNIT_2, MPI_POINTER PTR_CONFIG_PAGE_SAS_IO_UNIT_2,
  SasIOUnitPage2_t, MPI_POINTER pSasIOUnitPage2_t;

-#define MPI_SASIOUNITPAGE2_PAGEVERSION      (0x05)
+#define MPI_SASIOUNITPAGE2_PAGEVERSION      (0x06)

 /* values for SAS IO Unit Page 2 Status field */
+#define MPI_SAS_IOUNIT2_STATUS_DEVICE_LIMIT_EXCEEDED        (0x08)
+#define MPI_SAS_IOUNIT2_STATUS_ENCLOSURE_DEVICES_UNMAPPED   (0x04)
 #define MPI_SAS_IOUNIT2_STATUS_DISABLED_PERSISTENT_MAPPINGS (0x02)
 #define MPI_SAS_IOUNIT2_STATUS_FULL_PERSISTENT_MAPPINGS     (0x01)

@@ -2739,24 +2810,38 @@ typedef struct _CONFIG_PAGE_SAS_DEVICE_0
 } CONFIG_PAGE_SAS_DEVICE_0, MPI_POINTER PTR_CONFIG_PAGE_SAS_DEVICE_0,
  SasDevicePage0_t, MPI_POINTER pSasDevicePage0_t;

-#define MPI_SASDEVICE0_PAGEVERSION          (0x04)
+#define MPI_SASDEVICE0_PAGEVERSION          (0x05)

 /* values for SAS Device Page 0 AccessStatus field */
-#define MPI_SAS_DEVICE0_ASTATUS_NO_ERRORS               (0x00)
-#define MPI_SAS_DEVICE0_ASTATUS_SATA_INIT_FAILED        (0x01)
-#define MPI_SAS_DEVICE0_ASTATUS_SATA_CAPABILITY_FAILED  (0x02)
+#define MPI_SAS_DEVICE0_ASTATUS_NO_ERRORS                   (0x00)
+#define MPI_SAS_DEVICE0_ASTATUS_SATA_INIT_FAILED            (0x01)
+#define MPI_SAS_DEVICE0_ASTATUS_SATA_CAPABILITY_FAILED      (0x02)
+#define MPI_SAS_DEVICE0_ASTATUS_SATA_AFFILIATION_CONFLICT   (0x03)
+/* specific values for SATA Init failures */
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_UNKNOWN                 (0x10)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_AFFILIATION_CONFLICT    (0x11)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_DIAG                    (0x12)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_IDENTIFICATION          (0x13)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_CHECK_POWER             (0x14)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_PIO_SN                  (0x15)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_MDMA_SN                 (0x16)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_UDMA_SN                 (0x17)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_ZONING_VIOLATION        (0x18)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_NOT_ADDRESSABLE         (0x19)
+#define MPI_SAS_DEVICE0_ASTATUS_SIF_MAX                     (0x1F)

 /* values for SAS Device Page 0 Flags field */
-#define MPI_SAS_DEVICE0_FLAGS_SATA_SW_PRESERVE          (0x0200)
-#define MPI_SAS_DEVICE0_FLAGS_UNSUPPORTED_DEVICE        (0x0100)
-#define MPI_SAS_DEVICE0_FLAGS_SATA_48BIT_LBA_SUPPORTED  (0x0080)
-#define MPI_SAS_DEVICE0_FLAGS_SATA_SMART_SUPPORTED      (0x0040)
-#define MPI_SAS_DEVICE0_FLAGS_SATA_NCQ_SUPPORTED        (0x0020)
-#define MPI_SAS_DEVICE0_FLAGS_SATA_FUA_SUPPORTED        (0x0010)
-#define MPI_SAS_DEVICE0_FLAGS_PORT_SELECTOR_ATTACH      (0x0008)
-#define MPI_SAS_DEVICE0_FLAGS_MAPPING_PERSISTENT        (0x0004)
-#define MPI_SAS_DEVICE0_FLAGS_DEVICE_MAPPED             (0x0002)
-#define MPI_SAS_DEVICE0_FLAGS_DEVICE_PRESENT            (0x0001)
+#define MPI_SAS_DEVICE0_FLAGS_SATA_ASYNCHRONOUS_NOTIFY      (0x0400)
+#define MPI_SAS_DEVICE0_FLAGS_SATA_SW_PRESERVE              (0x0200)
+#define MPI_SAS_DEVICE0_FLAGS_UNSUPPORTED_DEVICE            (0x0100)
+#define MPI_SAS_DEVICE0_FLAGS_SATA_48BIT_LBA_SUPPORTED      (0x0080)
+#define MPI_SAS_DEVICE0_FLAGS_SATA_SMART_SUPPORTED          (0x0040)
+#define MPI_SAS_DEVICE0_FLAGS_SATA_NCQ_SUPPORTED            (0x0020)
+#define MPI_SAS_DEVICE0_FLAGS_SATA_FUA_SUPPORTED            (0x0010)
+#define MPI_SAS_DEVICE0_FLAGS_PORT_SELECTOR_ATTACH          (0x0008)
+#define MPI_SAS_DEVICE0_FLAGS_MAPPING_PERSISTENT            (0x0004)
+#define MPI_SAS_DEVICE0_FLAGS_DEVICE_MAPPED                 (0x0002)
+#define MPI_SAS_DEVICE0_FLAGS_DEVICE_PRESENT                (0x0001)

 /* see mpi_sas.h for values for SAS Device Page 0 DeviceInfo values */


--- a/drivers/message/fusion/lsi/mpi_history.txt
+++ b/drivers/message/fusion/lsi/mpi_history.txt
@@ -3,28 +3,28 @@
 MPI Header File Change History
 ==============================

- Copyright (c) 2000-2005 LSI Logic Corporation.
+ Copyright (c) 2000-2006 LSI Logic Corporation.

 ---------------------------------------
- Header Set Release Version:    01.05.13
- Header Set Release Date:       03-27-06
+ Header Set Release Version:    01.05.14
+ Header Set Release Date:       10-11-06
 ---------------------------------------

 Filename               Current version     Prior version
 ----------             ---------------     -------------
- mpi.h                  01.05.11            01.05.10
- mpi_ioc.h              01.05.11            01.05.10
- mpi_cnfg.h             01.05.12            01.05.11
- mpi_init.h             01.05.07            01.05.06
- mpi_targ.h             01.05.06            01.05.05
+ mpi.h                  01.05.12            01.05.11
+ mpi_ioc.h              01.05.12            01.05.11
+ mpi_cnfg.h             01.05.13            01.05.12
+ mpi_init.h             01.05.08            01.05.07
+ mpi_targ.h             01.05.06            01.05.06
 mpi_fc.h               01.05.01            01.05.01
 mpi_lan.h              01.05.01            01.05.01
 mpi_raid.h             01.05.02            01.05.02
 mpi_tool.h             01.05.03            01.05.03
 mpi_inb.h              01.05.01            01.05.01
- mpi_sas.h              01.05.03            01.05.02
+ mpi_sas.h              01.05.04            01.05.03
 mpi_type.h             01.05.02            01.05.02
- mpi_history.txt        01.05.13            01.05.12
+ mpi_history.txt        01.05.14            01.05.13


 *  Date      Version   Description
@@ -94,6 +94,7 @@ mpi.h
 *  08-03-05  01.05.09  Bumped MPI_HEADER_VERSION_UNIT.
 *  08-30-05  01.05.10  Added 2 new IOCStatus codes for Target.
 *  03-27-06  01.05.11  Bumped MPI_HEADER_VERSION_UNIT.
+ *  10-11-06  01.05.12  Bumped MPI_HEADER_VERSION_UNIT.
 *  --------------------------------------------------------------------------

 mpi_ioc.h
@@ -182,6 +183,14 @@ mpi_ioc.h
 *                      Added MPI_EVENT_SAS_INIT_TABLE_OVERFLOW and event
 *                      data structure.
 *                      Added MPI_EXT_IMAGE_TYPE_INITIALIZATION.
+ *  10-11-06  01.05.12  Added MPI_IOCFACTS_EXCEPT_METADATA_UNSUPPORTED.
+ *                      Added MaxInitiators field to PortFacts reply.
+ *                      Added SAS Device Status Change ReasonCode for
+ *                      asynchronous notificaiton.
+ *                      Added MPI_EVENT_SAS_EXPANDER_STATUS_CHANGE and event
+ *                      data structure.
+ *                      Added new ImageType values for FWDownload and FWUpload
+ *                      requests.
 *  --------------------------------------------------------------------------

 mpi_cnfg.h
@@ -447,6 +456,23 @@ mpi_cnfg.h
 *                      Added AdditionalControlFlags, MaxTargetPortConnectTime,
 *                      ReportDeviceMissingDelay, and IODeviceMissingDelay
 *                      fields to SAS IO Unit Page 1.
+ *  10-11-06  01.05.13  Added NumForceWWID field and ForceWWID array to
+ *                      Manufacturing Page 5.
+ *                      Added Manufacturing pages 8 through 10.
+ *                      Added defines for supported metadata size bits in
+ *                      CapabilitiesFlags field of IOC Page 6.
+ *                      Added defines for metadata size bits in VolumeSettings
+ *                      field of RAID Volume Page 0.
+ *                      Added SATA Link Reset settings, Enable SATA Asynchronous
+ *                      Notification bit, and HideNonZeroAttachedPhyIdentifiers
+ *                      bit to AdditionalControlFlags field of SAS IO Unit
+ *                      Page 1.
+ *                      Added defines for Enclosure Devices Unmapped and
+ *                      Device Limit Exceeded bits in Status field of SAS IO
+ *                      Unit Page 2.
+ *                      Added more AccessStatus values for SAS Device Page 0.
+ *                      Added bit for SATA Asynchronous Notification Support in
+ *                      Flags field of SAS Device Page 0.
 *  --------------------------------------------------------------------------

 mpi_init.h
@@ -490,6 +516,7 @@ mpi_init.h
 *  08-03-05  01.05.06  Fixed some MPI_SCSIIO32_MSGFLGS_ defines to make them
 *                      unique in the first 32 characters.
 *  03-27-06  01.05.07  Added Task Management type of Clear ACA.
+ *  10-11-06  01.05.08  Shortened define for Task Management type of Clear ACA.
 *  --------------------------------------------------------------------------

 mpi_targ.h
@@ -638,6 +665,8 @@ mpi_sas.h
 *                      and Remove Device operations to SAS IO Unit Control.
 *                      Added DevHandle field to SAS IO Unit Control request and
 *                      reply.
+ *  10-11-06  01.05.04  Fixed the name of a define for Operation field of SAS IO
+ *                      Unit Control request.
 *  --------------------------------------------------------------------------

 mpi_type.h
@@ -653,20 +682,20 @@ mpi_type.h

 mpi_history.txt         Parts list history

-Filename    01.05.13  01.05.12  01.05.11  01.05.10  01.05.09
----------  --------  --------  --------  --------  --------
-mpi.h       01.05.11  01.05.10  01.05.09  01.05.08  01.05.07
-mpi_ioc.h   01.05.11  01.05.10  01.05.09  01.05.09  01.05.08
-mpi_cnfg.h  01.05.12  01.05.11  01.05.10  01.05.09  01.05.08
-mpi_init.h  01.05.07  01.05.06  01.05.06  01.05.05  01.05.04
-mpi_targ.h  01.05.06  01.05.05  01.05.05  01.05.05  01.05.04
-mpi_fc.h    01.05.01  01.05.01  01.05.01  01.05.01  01.05.01
-mpi_lan.h   01.05.01  01.05.01  01.05.01  01.05.01  01.05.01
-mpi_raid.h  01.05.02  01.05.02  01.05.02  01.05.02  01.05.02
-mpi_tool.h  01.05.03  01.05.03  01.05.03  01.05.03  01.05.03
-mpi_inb.h   01.05.01  01.05.01  01.05.01  01.05.01  01.05.01
-mpi_sas.h   01.05.03  01.05.02  01.05.01  01.05.01  01.05.01
-mpi_type.h  01.05.02  01.05.02  01.05.01  01.05.01  01.05.01
+Filename    01.05.13   01.05.13   01.05.12   01.05.11   01.05.10   01.05.09
+----------  --------   --------   --------   --------   --------   --------
+mpi.h       01.05.12   01.05.11   01.05.10   01.05.09   01.05.08   01.05.07
+mpi_ioc.h   01.05.12   01.05.11   01.05.10   01.05.09   01.05.09   01.05.08
+mpi_cnfg.h  01.05.13   01.05.12   01.05.11   01.05.10   01.05.09   01.05.08
+mpi_init.h  01.05.08   01.05.07   01.05.06   01.05.06   01.05.05   01.05.04
+mpi_targ.h  01.05.06   01.05.06   01.05.05   01.05.05   01.05.05   01.05.04
+mpi_fc.h    01.05.01   01.05.01   01.05.01   01.05.01   01.05.01   01.05.01
+mpi_lan.h   01.05.01   01.05.01   01.05.01   01.05.01   01.05.01   01.05.01
+mpi_raid.h  01.05.02   01.05.02   01.05.02   01.05.02   01.05.02   01.05.02
+mpi_tool.h  01.05.03   01.05.03   01.05.03   01.05.03   01.05.03   01.05.03
+mpi_inb.h   01.05.01   01.05.01   01.05.01   01.05.01   01.05.01   01.05.01
+mpi_sas.h   01.05.04   01.05.03   01.05.02   01.05.01   01.05.01   01.05.01
+mpi_type.h  01.05.02   01.05.02   01.05.02   01.05.01   01.05.01   01.05.01

 Filename    01.05.08   01.05.07   01.05.06   01.05.05   01.05.04   01.05.03
 ----------  --------   --------   --------   --------   --------   --------

--- a/drivers/message/fusion/lsi/mpi_init.h
+++ b/drivers/message/fusion/lsi/mpi_init.h
 /*
- *  Copyright (c) 2000-2005 LSI Logic Corporation.
+ *  Copyright (c) 2000-2006 LSI Logic Corporation.
 *
 *
 *           Name:  mpi_init.h
 *          Title:  MPI initiator mode messages and structures
 *  Creation Date:  June 8, 2000
 *
- *    mpi_init.h Version:  01.05.07
+ *    mpi_init.h Version:  01.05.08
 *
 *  Version History
 *  ---------------
@@ -53,6 +53,7 @@
 *  08-03-05  01.05.06  Fixed some MPI_SCSIIO32_MSGFLGS_ defines to make them
 *                      unique in the first 32 characters.
 *  03-27-06  01.05.07  Added Task Management type of Clear ACA.
+ *  10-11-06  01.05.08  Shortened define for Task Management type of Clear ACA.
 *  --------------------------------------------------------------------------
 */

@@ -428,7 +429,7 @@ typedef struct _MSG_SCSI_TASK_MGMT
 #define MPI_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET    (0x05)
 #define MPI_SCSITASKMGMT_TASKTYPE_CLEAR_TASK_SET        (0x06)
 #define MPI_SCSITASKMGMT_TASKTYPE_QUERY_TASK            (0x07)
-#define MPI_SCSITASKMGMT_TASKTYPE_CLEAR_ACA             (0x08)
+#define MPI_SCSITASKMGMT_TASKTYPE_CLR_ACA               (0x08)

 /* MsgFlags bits */
 #define MPI_SCSITASKMGMT_MSGFLAGS_TARGET_RESET_OPTION   (0x00)

--- a/drivers/message/fusion/lsi/mpi_ioc.h
+++ b/drivers/message/fusion/lsi/mpi_ioc.h
 /*
- *  Copyright (c) 2000-2005 LSI Logic Corporation.
+ *  Copyright (c) 2000-2006 LSI Logic Corporation.
 *
 *
 *           Name:  mpi_ioc.h
 *          Title:  MPI IOC, Port, Event, FW Download, and FW Upload messages
 *  Creation Date:  August 11, 2000
 *
- *    mpi_ioc.h Version:  01.05.11
+ *    mpi_ioc.h Version:  01.05.12
 *
 *  Version History
 *  ---------------
@@ -98,6 +98,14 @@
 *                      Added MPI_EVENT_SAS_INIT_TABLE_OVERFLOW and event
 *                      data structure.
 *                      Added MPI_EXT_IMAGE_TYPE_INITIALIZATION.
+ *  10-11-06  01.05.12  Added MPI_IOCFACTS_EXCEPT_METADATA_UNSUPPORTED.
+ *                      Added MaxInitiators field to PortFacts reply.
+ *                      Added SAS Device Status Change ReasonCode for
+ *                      asynchronous notificaiton.
+ *                      Added MPI_EVENT_SAS_EXPANDER_STATUS_CHANGE and event
+ *                      data structure.
+ *                      Added new ImageType values for FWDownload and FWUpload
+ *                      requests.
 *  --------------------------------------------------------------------------
 */

@@ -264,6 +272,7 @@ typedef struct _MSG_IOC_FACTS_REPLY
 #define MPI_IOCFACTS_EXCEPT_RAID_CONFIG_INVALID         (0x0002)
 #define MPI_IOCFACTS_EXCEPT_FW_CHECKSUM_FAIL            (0x0004)
 #define MPI_IOCFACTS_EXCEPT_PERSISTENT_TABLE_FULL       (0x0008)
+#define MPI_IOCFACTS_EXCEPT_METADATA_UNSUPPORTED        (0x0010)

 #define MPI_IOCFACTS_FLAGS_FW_DOWNLOAD_BOOT             (0x01)
 #define MPI_IOCFACTS_FLAGS_REPLY_FIFO_HOST_SIGNAL       (0x02)
@@ -328,7 +337,8 @@ typedef struct _MSG_PORT_FACTS_REPLY
     U16                    MaxPostedCmdBuffers;        /* 1Ch */
     U16                    MaxPersistentIDs;           /* 1Eh */
     U16                    MaxLanBuckets;              /* 20h */
-     U16                    Reserved4;                  /* 22h */
+     U8                     MaxInitiators;              /* 22h */
+     U8                     Reserved4;                  /* 23h */
     U32                    Reserved5;                  /* 24h */
 } MSG_PORT_FACTS_REPLY, MPI_POINTER PTR_MSG_PORT_FACTS_REPLY,
  PortFactsReply_t, MPI_POINTER pPortFactsReply_t;
@@ -487,6 +497,7 @@ typedef struct _MSG_EVENT_ACK_REPLY
 #define MPI_EVENT_SAS_INIT_DEVICE_STATUS_CHANGE (0x00000018)
 #define MPI_EVENT_SAS_INIT_TABLE_OVERFLOW       (0x00000019)
 #define MPI_EVENT_SAS_SMP_ERROR                 (0x0000001A)
+#define MPI_EVENT_SAS_EXPANDER_STATUS_CHANGE    (0x0000001B)
 #define MPI_EVENT_LOG_ENTRY_ADDED               (0x00000021)

 /* AckRequired field values */
@@ -593,6 +604,7 @@ typedef struct _EVENT_DATA_SAS_DEVICE_STATUS_CHANGE
 #define MPI_EVENT_SAS_DEV_STAT_RC_ABORT_TASK_SET_INTERNAL   (0x0A)
 #define MPI_EVENT_SAS_DEV_STAT_RC_CLEAR_TASK_SET_INTERNAL   (0x0B)
 #define MPI_EVENT_SAS_DEV_STAT_RC_QUERY_TASK_INTERNAL       (0x0C)
+#define MPI_EVENT_SAS_DEV_STAT_RC_ASYNC_NOTIFICATION        (0x0D)


 /* SCSI Event data for Queue Full event */
@@ -895,6 +907,54 @@ typedef struct _EVENT_DATA_SAS_INIT_TABLE_OVERFLOW
  MpiEventDataSasInitTableOverflow_t,
  MPI_POINTER pMpiEventDataSasInitTableOverflow_t;

+/* SAS Expander Status Change Event data */
+
+typedef struct _EVENT_DATA_SAS_EXPANDER_STATUS_CHANGE
+{
+    U8                      ReasonCode;             /* 00h */
+    U8                      Reserved1;              /* 01h */
+    U16                     Reserved2;              /* 02h */
+    U8                      PhysicalPort;           /* 04h */
+    U8                      Reserved3;              /* 05h */
+    U16                     EnclosureHandle;        /* 06h */
+    U64                     SASAddress;             /* 08h */
+    U32                     DiscoveryStatus;        /* 10h */
+    U16                     DevHandle;              /* 14h */
+    U16                     ParentDevHandle;        /* 16h */
+    U16                     ExpanderChangeCount;    /* 18h */
+    U16                     ExpanderRouteIndexes;   /* 1Ah */
+    U8                      NumPhys;                /* 1Ch */
+    U8                      SASLevel;               /* 1Dh */
+    U8                      Flags;                  /* 1Eh */
+    U8                      Reserved4;              /* 1Fh */
+} EVENT_DATA_SAS_EXPANDER_STATUS_CHANGE,
+  MPI_POINTER PTR_EVENT_DATA_SAS_EXPANDER_STATUS_CHANGE,
+  MpiEventDataSasExpanderStatusChange_t,
+  MPI_POINTER pMpiEventDataSasExpanderStatusChange_t;
+
+/* values for ReasonCode field of SAS Expander Status Change Event data */
+#define MPI_EVENT_SAS_EXP_RC_ADDED                      (0x00)
+#define MPI_EVENT_SAS_EXP_RC_NOT_RESPONDING             (0x01)
+
+/* values for DiscoveryStatus field of SAS Expander Status Change Event data */
+#define MPI_EVENT_SAS_EXP_DS_LOOP_DETECTED              (0x00000001)
+#define MPI_EVENT_SAS_EXP_DS_UNADDRESSABLE_DEVICE       (0x00000002)
+#define MPI_EVENT_SAS_EXP_DS_MULTIPLE_PORTS             (0x00000004)
+#define MPI_EVENT_SAS_EXP_DS_EXPANDER_ERR               (0x00000008)
+#define MPI_EVENT_SAS_EXP_DS_SMP_TIMEOUT                (0x00000010)
+#define MPI_EVENT_SAS_EXP_DS_OUT_ROUTE_ENTRIES          (0x00000020)
+#define MPI_EVENT_SAS_EXP_DS_INDEX_NOT_EXIST            (0x00000040)
+#define MPI_EVENT_SAS_EXP_DS_SMP_FUNCTION_FAILED        (0x00000080)
+#define MPI_EVENT_SAS_EXP_DS_SMP_CRC_ERROR              (0x00000100)
+#define MPI_EVENT_SAS_EXP_DS_SUBTRACTIVE_LINK           (0x00000200)
+#define MPI_EVENT_SAS_EXP_DS_TABLE_LINK                 (0x00000400)
+#define MPI_EVENT_SAS_EXP_DS_UNSUPPORTED_DEVICE         (0x00000800)
+
+/* values for Flags field of SAS Expander Status Change Event data */
+#define MPI_EVENT_SAS_EXP_FLAGS_ROUTE_TABLE_CONFIG      (0x02)
+#define MPI_EVENT_SAS_EXP_FLAGS_CONFIG_IN_PROGRESS      (0x01)
+
+

 /*****************************************************************************
 *
@@ -926,6 +986,10 @@ typedef struct _MSG_FW_DOWNLOAD
 #define MPI_FW_DOWNLOAD_ITYPE_BIOS              (0x02)
 #define MPI_FW_DOWNLOAD_ITYPE_NVDATA            (0x03)
 #define MPI_FW_DOWNLOAD_ITYPE_BOOTLOADER        (0x04)
+#define MPI_FW_DOWNLOAD_ITYPE_MANUFACTURING     (0x06)
+#define MPI_FW_DOWNLOAD_ITYPE_CONFIG_1          (0x07)
+#define MPI_FW_DOWNLOAD_ITYPE_CONFIG_2          (0x08)
+#define MPI_FW_DOWNLOAD_ITYPE_MEGARAID          (0x09)


 typedef struct _FWDownloadTCSGE
@@ -980,6 +1044,11 @@ typedef struct _MSG_FW_UPLOAD
 #define MPI_FW_UPLOAD_ITYPE_NVDATA          (0x03)
 #define MPI_FW_UPLOAD_ITYPE_BOOTLOADER      (0x04)
 #define MPI_FW_UPLOAD_ITYPE_FW_BACKUP       (0x05)
+#define MPI_FW_UPLOAD_ITYPE_MANUFACTURING   (0x06)
+#define MPI_FW_UPLOAD_ITYPE_CONFIG_1        (0x07)
+#define MPI_FW_UPLOAD_ITYPE_CONFIG_2        (0x08)
+#define MPI_FW_UPLOAD_ITYPE_MEGARAID        (0x09)
+#define MPI_FW_UPLOAD_ITYPE_COMPLETE        (0x0A)

 typedef struct _FWUploadTCSGE
 {

--- a/drivers/message/fusion/lsi/mpi_log_sas.h
+++ b/drivers/message/fusion/lsi/mpi_log_sas.h
--- a/drivers/message/fusion/lsi/mpi_sas.h
+++ b/drivers/message/fusion/lsi/mpi_sas.h
 /*
- *  Copyright (c) 2004 LSI Logic Corporation.
+ *  Copyright (c) 2004-2006 LSI Logic Corporation.
 *
 *
 *           Name:  mpi_sas.h
 *          Title:  MPI Serial Attached SCSI structures and definitions
 *  Creation Date:  August 19, 2004
 *
- *    mpi_sas.h Version:  01.05.03
+ *    mpi_sas.h Version:  01.05.04
 *
 *  Version History
 *  ---------------
@@ -21,6 +21,8 @@
 *                      and Remove Device operations to SAS IO Unit Control.
 *                      Added DevHandle field to SAS IO Unit Control request and
 *                      reply.
+ *  10-11-06  01.05.04  Fixed the name of a define for Operation field of SAS IO
+ *                      Unit Control request.
 *  --------------------------------------------------------------------------
 */

@@ -237,7 +239,8 @@ typedef struct _MSG_SAS_IOUNIT_CONTROL_REQUEST
 #define MPI_SAS_OP_SEND_PRIMITIVE               (0x0A)
 #define MPI_SAS_OP_FORCE_FULL_DISCOVERY         (0x0B)
 #define MPI_SAS_OP_TRANSMIT_PORT_SELECT_SIGNAL  (0x0C)
-#define MPI_SAS_OP_TRANSMIT_REMOVE_DEVICE       (0x0D)
+#define MPI_SAS_OP_TRANSMIT_REMOVE_DEVICE       (0x0D)  /* obsolete name */
+#define MPI_SAS_OP_REMOVE_DEVICE                (0x0D)

 /* values for the PrimFlags field */
 #define MPI_SAS_PRIMFLAGS_SINGLE                (0x08)

--- a/drivers/message/fusion/mptbase.c
+++ b/drivers/message/fusion/mptbase.c
--- a/drivers/message/fusion/mptbase.h
+++ b/drivers/message/fusion/mptbase.h
@@ -6,7 +6,7 @@
 *      running LSI Logic Fusion MPT (Message Passing Technology) firmware.
 *
 *  Copyright (c) 1999-2007 LSI Logic Corporation
- *  (mailto:mpt_linux_developer@lsil.com)
+ *  (mailto:mpt_linux_developer@lsi.com)
 *
 */
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
@@ -75,8 +75,8 @@
 #define COPYRIGHT	"Copyright (c) 1999-2007 " MODULEAUTHOR
 #endif

-#define MPT_LINUX_VERSION_COMMON	"3.04.03"
-#define MPT_LINUX_PACKAGE_NAME		"@(#)mptlinux-3.04.03"
+#define MPT_LINUX_VERSION_COMMON	"3.04.04"
+#define MPT_LINUX_PACKAGE_NAME		"@(#)mptlinux-3.04.04"
 #define WHAT_MAGIC_STRING		"@" "(" "#" ")"

 #define show_mptmod_ver(s,ver)  \
@@ -172,6 +172,9 @@
 #define MPT_SCSI_SG_DEPTH	40
 #endif

+/* debug print string length used for events and iocstatus */
+# define EVENT_DESCR_STR_SZ             100
+
 #ifdef __KERNEL__	/* { */
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/

@@ -334,8 +337,8 @@ typedef struct _VirtTarget {
 	struct scsi_target	*starget;
 	u8			 tflags;
 	u8			 ioc_id;
-	u8			 target_id;
-	u8			 bus_id;
+	u8			 id;
+	u8			 channel;
 	u8			 minSyncFactor;	/* 0xFF is async */
 	u8			 maxOffset;	/* 0 if async */
 	u8			 maxWidth;	/* 0 if narrow, 1 if wide */
@@ -344,13 +347,12 @@ typedef struct _VirtTarget {
 	u8			 type;		/* byte 0 of Inquiry data */
 	u8			 deleted;	/* target in process of being removed */
 	u32			 num_luns;
-	u32			 luns[8];		/* Max LUNs is 256 */
 } VirtTarget;

 typedef struct _VirtDevice {
 	VirtTarget		*vtarget;
 	u8			 configured_lun;
-	u32			 lun;
+	int			 lun;
 } VirtDevice;

 /*
@@ -412,7 +414,7 @@ typedef struct _MPT_IOCTL {
 	u8			 rsvd;
 	u8			 status;	/* current command status */
 	u8			 reset;		/* 1 if bus reset allowed */
-	u8			 target;	/* target for reset */
+	u8			 id;		/* target for reset */
 	struct mutex		 ioctl_mutex;
 } MPT_IOCTL;

@@ -483,10 +485,24 @@ typedef	struct _SasCfgData {
 						 */
 }SasCfgData;

+/*
+ * Inactive volume link list of raid component data
+ * @inactive_list
+ */
+struct inactive_raid_component_info {
+	struct 	 list_head list;
+	u8		 volumeID;		/* volume target id */
+	u8		 volumeBus;		/* volume channel */
+	IOC_3_PHYS_DISK	 d;			/* phys disk info */
+};
+
 typedef	struct _RaidCfgData {
 	IOCPage2_t	*pIocPg2;		/* table of Raid Volumes */
 	IOCPage3_t	*pIocPg3;		/* table of physical disks */
-	int		 isRaid;		/* bit field, 1 if RAID */
+	struct semaphore	inactive_list_mutex;
+	struct list_head	inactive_list; /* link list for physical
+						disk that belong in
+						inactive volumes */
 }RaidCfgData;

 typedef struct _FcCfgData {
@@ -528,6 +544,8 @@ typedef struct _MPT_ADAPTER
 	u32			 mem_phys;	/* == f4020000 (mmap) */
 	u32			 pio_mem_phys;	/* Programmed IO (downloadboot) */
 	int			 mem_size;	/* mmap memory size */
+	int			 number_of_buses;
+	int			 devices_per_bus;
 	int			 alloc_total;
 	u32			 last_state;
 	int			 active;
@@ -607,6 +625,8 @@ typedef struct _MPT_ADAPTER
 	u8			 persist_reply_frame[MPT_DEFAULT_FRAME_SIZE]; /* persist reply */
 	LANPage0_t		 lan_cnfg_page0;
 	LANPage1_t		 lan_cnfg_page1;
+
+	u8			 ir_firmware; /* =1 if IR firmware detected */
 	/*
 	 * Description: errata_flag_1064
 	 * If a PCIX read occurs within 1 or 2 cycles after the chip receives
@@ -790,12 +810,6 @@ typedef struct _mpt_sge {
 #define ddvprintk(x)
 #endif

-#ifdef MPT_DEBUG_NEGO
-#define dnegoprintk(x)  printk x
-#else
-#define dnegoprintk(x)
-#endif
-
 #if defined(MPT_DEBUG_DV) || defined(MPT_DEBUG_DV_TINY)
 #define ddvtprintk(x)  printk x
 #else
@@ -957,7 +971,6 @@ typedef struct _MPT_SCSI_HOST {
 	int			  port;
 	u32			  pad0;
 	struct scsi_cmnd	**ScsiLookup;
-	VirtTarget		**Targets;
 	MPT_LOCAL_REPLY		 *pLocal;		/* used for internal commands */
 	struct timer_list	  timer;
 		/* Pool of memory for holding SCpnts before doing
@@ -981,6 +994,7 @@ typedef struct _MPT_SCSI_HOST {
 	int			  scandv_wait_done;
 	long			  last_queue_full;
 	u16			  tm_iocstatus;
+	struct list_head	  target_reset_list;
 } MPT_SCSI_HOST;

 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
@@ -1046,6 +1060,7 @@ extern void	 mpt_alloc_fw_memory(MPT_ADAPTER *ioc, int size);
 extern void	 mpt_free_fw_memory(MPT_ADAPTER *ioc);
 extern int	 mpt_findImVolumes(MPT_ADAPTER *ioc);
 extern int	 mptbase_sas_persist_operation(MPT_ADAPTER *ioc, u8 persist_opcode);
+extern int	 mpt_raid_phys_disk_pg0(MPT_ADAPTER *ioc, u8 phys_disk_num, pRaidPhysDiskPage0_t phys_disk);

 /*
 *  Public data decl's...

--- a/drivers/message/fusion/mptctl.c
+++ b/drivers/message/fusion/mptctl.c
@@ -5,7 +5,7 @@
 *      running LSI Logic Fusion MPT (Message Passing Technology) firmware.
 *
 *  Copyright (c) 1999-2007 LSI Logic Corporation
- *  (mailto:mpt_linux_developer@lsil.com)
+ *  (mailto:mpt_linux_developer@lsi.com)
 *
 */
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
@@ -313,7 +313,7 @@ static void mptctl_timeout_expired (MPT_IOCTL *ioctl)
 		 */
 		dctlprintk((MYIOC_s_INFO_FMT "Calling HardReset! \n",
 			 ioctl->ioc->name));
-		mpt_HardResetHandler(ioctl->ioc, NO_SLEEP);
+		mpt_HardResetHandler(ioctl->ioc, CAN_SLEEP);
 	}
 	return;

@@ -361,7 +361,7 @@ static int mptctl_bus_reset(MPT_IOCTL *ioctl)
 			ioctl->ioc->name, mf));

 	pScsiTm = (SCSITaskMgmt_t *) mf;
-	pScsiTm->TargetID = ioctl->target;
+	pScsiTm->TargetID = ioctl->id;
 	pScsiTm->Bus = hd->port;	/* 0 */
 	pScsiTm->ChainOffset = 0;
 	pScsiTm->Function = MPI_FUNCTION_SCSI_TASK_MGMT;
@@ -1159,15 +1159,12 @@ mptctl_getiocinfo (unsigned long arg, unsigned int data_size)
 	struct mpt_ioctl_iocinfo *karg;
 	MPT_ADAPTER		*ioc;
 	struct pci_dev		*pdev;
-	struct Scsi_Host	*sh;
-	MPT_SCSI_HOST		*hd;
 	int			iocnum;
-	int			numDevices = 0;
-	unsigned int		max_id;
-	int			ii;
 	unsigned int		port;
 	int			cim_rev;
 	u8			revision;
+	struct scsi_device 	*sdev;
+	VirtDevice		*vdev;

 	dctlprintk((": mptctl_getiocinfo called.\n"));
 	/* Add of PCI INFO results in unaligned access for
@@ -1257,23 +1254,16 @@ mptctl_getiocinfo (unsigned long arg, unsigned int data_size)

 	/* Get number of devices
         */
-	if ((sh = ioc->sh) != NULL) {
-		 /* sh->max_id = maximum target ID + 1
-		 */
-		max_id = sh->max_id - 1;
-		hd = (MPT_SCSI_HOST *) sh->hostdata;
-
-		/* Check all of the target structures and
-		 * keep a counter.
-		 */
-		if (hd && hd->Targets) {
-			for (ii = 0; ii <= max_id; ii++) {
-				if (hd->Targets[ii])
-					numDevices++;
-			}
+	karg->numDevices = 0;
+	if (ioc->sh) {
+		shost_for_each_device(sdev, ioc->sh) {
+			vdev = sdev->hostdata;
+			if (vdev->vtarget->tflags &
+			    MPT_TARGET_FLAGS_RAID_COMPONENT)
+				continue;
+			karg->numDevices++;
 		}
 	}
-	karg->numDevices = numDevices;

 	/* Set the BIOS and FW Version
 	 */
@@ -1319,21 +1309,16 @@ mptctl_gettargetinfo (unsigned long arg)
 	struct mpt_ioctl_targetinfo __user *uarg = (void __user *) arg;
 	struct mpt_ioctl_targetinfo karg;
 	MPT_ADAPTER		*ioc;
-	struct Scsi_Host	*sh;
-	MPT_SCSI_HOST		*hd;
-	VirtTarget		*vdev;
+	VirtDevice		*vdev;
 	char			*pmem;
 	int			*pdata;
-	IOCPage2_t		*pIoc2;
-	IOCPage3_t		*pIoc3;
 	int			iocnum;
 	int			numDevices = 0;
-	unsigned int		max_id;
-	int			id, jj, indexed_lun, lun_index;
-	u32			lun;
+	int			lun;
 	int			maxWordsLeft;
 	int			numBytes;
-	u8			port, devType, bus_id;
+	u8			port;
+	struct scsi_device 	*sdev;

 	dctlprintk(("mptctl_gettargetinfo called.\n"));
 	if (copy_from_user(&karg, uarg, sizeof(struct mpt_ioctl_targetinfo))) {
@@ -1389,74 +1374,22 @@ mptctl_gettargetinfo (unsigned long arg)

 	/* Get number of devices
         */
-	if ((sh = ioc->sh) != NULL) {
-
-		max_id = sh->max_id - 1;
-		hd = (MPT_SCSI_HOST *) sh->hostdata;
-
-		/* Check all of the target structures.
-		 * Save the Id and increment the counter,
-		 * if ptr non-null.
-		 * sh->max_id = maximum target ID + 1
-		 */
-		if (hd && hd->Targets) {
-			mpt_findImVolumes(ioc);
-			pIoc2 = ioc->raid_data.pIocPg2;
-			for ( id = 0; id <= max_id; ) {
-				if ( pIoc2 && pIoc2->NumActiveVolumes ) {
-					if ( id == pIoc2->RaidVolume[0].VolumeID ) {
-						if (maxWordsLeft <= 0) {
-							printk(KERN_ERR "mptctl_gettargetinfo - "
-			"buffer is full but volume is available on ioc %d\n, numDevices=%d", iocnum, numDevices);
-							goto data_space_full;
-						}
-						if ( ( pIoc2->RaidVolume[0].Flags & MPI_IOCPAGE2_FLAG_VOLUME_INACTIVE ) == 0 )
-                        				devType = 0x80;
-                    				else
-                        				devType = 0xC0;
-						bus_id = pIoc2->RaidVolume[0].VolumeBus;
-	            				numDevices++;
-                    				*pdata = ( (devType << 24) | (bus_id << 8) | id );
-						dctlprintk((KERN_ERR "mptctl_gettargetinfo - "
-		"volume ioc=%d target=%x numDevices=%d pdata=%p\n", iocnum, *pdata, numDevices, pdata));
-                    				pdata++;
-						--maxWordsLeft;
-						goto next_id;
-					} else {
-						pIoc3 = ioc->raid_data.pIocPg3;
-            					for ( jj = 0; jj < pIoc3->NumPhysDisks; jj++ ) {
-                    					if ( pIoc3->PhysDisk[jj].PhysDiskID == id )
-								goto next_id;
-						}
-					}
-				}
-				if ( (vdev = hd->Targets[id]) ) {
-					for (jj = 0; jj <= MPT_LAST_LUN; jj++) {
-						lun_index = (jj >> 5);
-						indexed_lun = (jj % 32);
-						lun = (1 << indexed_lun);
-						if (vdev->luns[lun_index] & lun) {
-							if (maxWordsLeft <= 0) {
-								printk(KERN_ERR "mptctl_gettargetinfo - "
-			"buffer is full but more targets are available on ioc %d numDevices=%d\n", iocnum, numDevices);
-								goto data_space_full;
-							}
-							bus_id = vdev->bus_id;
-							numDevices++;
-                            				*pdata = ( (jj << 16) | (bus_id << 8) | id );
-							dctlprintk((KERN_ERR "mptctl_gettargetinfo - "
-		"target ioc=%d target=%x numDevices=%d pdata=%p\n", iocnum, *pdata, numDevices, pdata));
-							pdata++;
-							--maxWordsLeft;
-						}
-					}
-				}
-next_id:
-				id++;
-			}
+	if (ioc->sh){
+		shost_for_each_device(sdev, ioc->sh) {
+			if (!maxWordsLeft)
+				continue;
+			vdev = sdev->hostdata;
+			if (vdev->vtarget->tflags &
+			    MPT_TARGET_FLAGS_RAID_COMPONENT)
+				continue;
+			lun = (vdev->vtarget->raidVolume) ? 0x80 : vdev->lun;
+			*pdata = (((u8)lun << 16) + (vdev->vtarget->channel << 8) +
+			    (vdev->vtarget->id ));
+			pdata++;
+			numDevices++;
+			--maxWordsLeft;
 		}
 	}
-data_space_full:
 	karg.numDevices = numDevices;

 	/* Copy part of the data from kernel memory to user memory
@@ -1821,6 +1754,7 @@ mptctl_do_mpt_command (struct mpt_ioctl_command karg, void __user *mfPtr)
 	int		msgContext;
 	u16		req_idx;
 	ulong 		timeout;
+	struct scsi_device *sdev;

 	dctlprintk(("mptctl_do_mpt_command called.\n"));
 	bufIn.kptr = bufOut.kptr = NULL;
@@ -1902,14 +1836,13 @@ mptctl_do_mpt_command (struct mpt_ioctl_command karg, void __user *mfPtr)
 	case MPI_FUNCTION_SCSI_IO_REQUEST:
 		if (ioc->sh) {
 			SCSIIORequest_t *pScsiReq = (SCSIIORequest_t *) mf;
-			VirtTarget	*pTarget = NULL;
-			MPT_SCSI_HOST	*hd = NULL;
 			int qtag = MPI_SCSIIO_CONTROL_UNTAGGED;
 			int scsidir = 0;
-			int target = (int) pScsiReq->TargetID;
 			int dataSize;
+			u32 id;

-			if ((target < 0) || (target >= ioc->sh->max_id)) {
+			id = (ioc->devices_per_bus == 0) ? 256 : ioc->devices_per_bus;
+			if (pScsiReq->TargetID > id) {
 				printk(KERN_ERR "%s@%d::mptctl_do_mpt_command - "
 					"Target ID out of bounds. \n",
 					__FILE__, __LINE__);
@@ -1917,6 +1850,14 @@ mptctl_do_mpt_command (struct mpt_ioctl_command karg, void __user *mfPtr)
 				goto done_free_mem;
 			}

+			if (pScsiReq->Bus >= ioc->number_of_buses) {
+				printk(KERN_ERR "%s@%d::mptctl_do_mpt_command - "
+					"Target Bus out of bounds. \n",
+					__FILE__, __LINE__);
+				rc = -ENODEV;
+				goto done_free_mem;
+			}
+
 			pScsiReq->MsgFlags &= ~MPI_SCSIIO_MSGFLGS_SENSE_WIDTH;
 			pScsiReq->MsgFlags |= mpt_msg_flags();

@@ -1936,13 +1877,15 @@ mptctl_do_mpt_command (struct mpt_ioctl_command karg, void __user *mfPtr)
 				cpu_to_le32(ioc->sense_buf_low_dma
 				   + (req_idx * MPT_SENSE_BUFFER_ALLOC));

-			if ((hd = (MPT_SCSI_HOST *) ioc->sh->hostdata)) {
-				if (hd->Targets)
-					pTarget = hd->Targets[target];
-			}
+			shost_for_each_device(sdev, ioc->sh) {
+				struct scsi_target *starget = scsi_target(sdev);
+				VirtTarget *vtarget = starget->hostdata;

-			if (pTarget &&(pTarget->tflags & MPT_TARGET_FLAGS_Q_YES))
-				qtag = MPI_SCSIIO_CONTROL_SIMPLEQ;
+				if ((pScsiReq->TargetID == vtarget->id) &&
+				    (pScsiReq->Bus == vtarget->channel) &&
+				    (vtarget->tflags & MPT_TARGET_FLAGS_Q_YES))
+					qtag = MPI_SCSIIO_CONTROL_SIMPLEQ;
+			}

 			/* Have the IOCTL driver set the direction based
 			 * on the dataOutSize (ordering issue with Sparc).
@@ -1959,7 +1902,7 @@ mptctl_do_mpt_command (struct mpt_ioctl_command karg, void __user *mfPtr)
 			pScsiReq->DataLength = cpu_to_le32(dataSize);

 			ioc->ioctl->reset = MPTCTL_RESET_OK;
-			ioc->ioctl->target = target;
+			ioc->ioctl->id = pScsiReq->TargetID;

 		} else {
 			printk(KERN_ERR "%s@%d::mptctl_do_mpt_command - "
@@ -2038,7 +1981,7 @@ mptctl_do_mpt_command (struct mpt_ioctl_command karg, void __user *mfPtr)
 			pScsiReq->DataLength = cpu_to_le32(dataSize);

 			ioc->ioctl->reset = MPTCTL_RESET_OK;
-			ioc->ioctl->target = pScsiReq->TargetID;
+			ioc->ioctl->id = pScsiReq->TargetID;
 		} else {
 			printk(KERN_ERR "%s@%d::mptctl_do_mpt_command - "
 				"SCSI driver is not loaded. \n",

--- a/drivers/message/fusion/mptctl.h
+++ b/drivers/message/fusion/mptctl.h
@@ -6,7 +6,7 @@
 *      running LSI Logic Fusion MPT (Message Passing Technology) firmware.
 *
 *  Copyright (c) 1999-2007 LSI Logic Corporation
- *  (mailto:mpt_linux_developer@lsil.com)
+ *  (mailto:mpt_linux_developer@lsi.com)
 *
 */
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/

--- a/drivers/message/fusion/mptfc.c
+++ b/drivers/message/fusion/mptfc.c
@@ -4,7 +4,7 @@
 *      running LSI Logic Fusion MPT (Message Passing Technology) firmware.
 *
 *  Copyright (c) 1999-2007 LSI Logic Corporation
- *  (mailto:mpt_linux_developer@lsil.com)
+ *  (mailto:mpt_linux_developer@lsi.com)
 *
 */
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
@@ -86,6 +86,12 @@ MODULE_PARM_DESC(mptfc_dev_loss_tmo, " Initial time the driver programs the "
 				     " return following a device loss event."
 				     "  Default=60.");

+/* scsi-mid layer global parmeter is max_report_luns, which is 511 */
+#define MPTFC_MAX_LUN (16895)
+static int max_lun = MPTFC_MAX_LUN;
+module_param(max_lun, int, 0);
+MODULE_PARM_DESC(max_lun, " max lun, default=16895 ");
+
 static int	mptfcDoneCtx = -1;
 static int	mptfcTaskCtx = -1;
 static int	mptfcInternalCtx = -1; /* Used only for internal commands */
@@ -292,10 +298,9 @@ mptfc_GetFcDevPage0(MPT_ADAPTER *ioc, int ioc_port,
 	U32			 port_id = 0xffffff;
 	int			 num_targ = 0;
 	int			 max_bus = ioc->facts.MaxBuses;
-	int			 max_targ = ioc->facts.MaxDevices;
+	int			 max_targ;

-	if (max_bus == 0 || max_targ == 0)
-		goto out;
+	max_targ = (ioc->facts.MaxDevices == 0) ? 256 : ioc->facts.MaxDevices;

 	data_sz = sizeof(FCDevicePage0_t) * max_bus * max_targ;
 	p_p0 = p0_array =  kzalloc(data_sz, GFP_KERNEL);
@@ -467,8 +472,8 @@ mptfc_register_dev(MPT_ADAPTER *ioc, int channel, FCDevicePage0_t *pg0)
 			if (ri->starget) {
 				vtarget = ri->starget->hostdata;
 				if (vtarget) {
-					vtarget->target_id = pg0->CurrentTargetID;
-					vtarget->bus_id = pg0->CurrentBus;
+					vtarget->id = pg0->CurrentTargetID;
+					vtarget->channel = pg0->CurrentBus;
 				}
 			}
 			*((struct mptfc_rport_info **)rport->dd_data) = ri;
@@ -540,8 +545,8 @@ mptfc_target_alloc(struct scsi_target *starget)
 	if (rport) {
 		ri = *((struct mptfc_rport_info **)rport->dd_data);
 		if (ri) {	/* better be! */
-			vtarget->target_id = ri->pg0.CurrentTargetID;
-			vtarget->bus_id = ri->pg0.CurrentBus;
+			vtarget->id = ri->pg0.CurrentTargetID;
+			vtarget->channel = ri->pg0.CurrentBus;
 			ri->starget = starget;
 			rc = 0;
 		}
@@ -592,7 +597,6 @@ mptfc_slave_alloc(struct scsi_device *sdev)
 	if (vtarget->num_luns == 0) {
 		vtarget->ioc_id = hd->ioc->id;
 		vtarget->tflags = MPT_TARGET_FLAGS_Q_YES;
-		hd->Targets[sdev->id] = vtarget;
 	}

 	vdev->vtarget = vtarget;
@@ -630,16 +634,17 @@ mptfc_qcmd(struct scsi_cmnd *SCpnt, void (*done)(struct scsi_cmnd *))
 	struct mptfc_rport_info	*ri;
 	struct fc_rport	*rport = starget_to_rport(scsi_target(SCpnt->device));
 	int		err;
+	VirtDevice	*vdev = SCpnt->device->hostdata;

-	err = fc_remote_port_chkready(rport);
-	if (unlikely(err)) {
-		SCpnt->result = err;
+	if (!vdev || !vdev->vtarget) {
+		SCpnt->result = DID_NO_CONNECT << 16;
 		done(SCpnt);
 		return 0;
 	}

-	if (!SCpnt->device->hostdata) {	/* vdev */
-		SCpnt->result = DID_NO_CONNECT << 16;
+	err = fc_remote_port_chkready(rport);
+	if (unlikely(err)) {
+		SCpnt->result = err;
 		done(SCpnt);
 		return 0;
 	}
@@ -1143,7 +1148,7 @@ mptfc_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		printk(MYIOC_s_WARN_FMT
 			"Skipping ioc=%p because SCSI Initiator mode is NOT enabled!\n",
 			ioc->name, ioc);
-		return -ENODEV;
+		return 0;
 	}

 	sh = scsi_host_alloc(&mptfc_driver_template, sizeof(MPT_SCSI_HOST));
@@ -1173,10 +1178,9 @@ mptfc_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	/* set 16 byte cdb's */
 	sh->max_cmd_len = 16;

-	sh->max_id = MPT_MAX_FC_DEVICES<256 ? MPT_MAX_FC_DEVICES : 255;
+	sh->max_id = ioc->pfacts->MaxDevices;
+	sh->max_lun = max_lun;

-	sh->max_lun = MPT_LAST_LUN + 1;
-	sh->max_channel = 0;
 	sh->this_id = ioc->pfacts[0].PortSCSIID;

 	/* Required entry.
@@ -1230,19 +1234,6 @@ mptfc_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	dprintk((MYIOC_s_INFO_FMT "ScsiLookup @ %p\n",
 		 ioc->name, hd->ScsiLookup));

-	/* Allocate memory for the device structures.
-	 * A non-Null pointer at an offset
-	 * indicates a device exists.
-	 * max_id = 1 + maximum id (hosts.h)
-	 */
-	hd->Targets = kcalloc(sh->max_id, sizeof(void *), GFP_ATOMIC);
-	if (!hd->Targets) {
-		error = -ENOMEM;
-		goto out_mptfc_probe;
-	}
-
-	dprintk((KERN_INFO "  vdev @ %p\n", hd->Targets));
-
 	/* Clear the TM flags
 	 */
 	hd->tmPending = 0;

--- a/drivers/message/fusion/mptlan.c
+++ b/drivers/message/fusion/mptlan.c
@@ -5,6 +5,7 @@
 *      running LSI Logic Fusion MPT (Message Passing Technology) firmware.
 *
 *  Copyright (c) 2000-2007 LSI Logic Corporation
+ *  (mailto:mpt_linux_developer@lsi.com)
 *
 */
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/

--- a/drivers/message/fusion/mptlan.h
+++ b/drivers/message/fusion/mptlan.h
@@ -5,6 +5,7 @@
 *      running LSI Logic Fusion MPT (Message Passing Technology) firmware.
 *
 *  Copyright (c) 2000-2007 LSI Logic Corporation
+ *  (mailto:mpt_linux_developer@lsi.com)
 *
 */
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/

--- a/drivers/message/fusion/mptsas.c
+++ b/drivers/message/fusion/mptsas.c
--- a/drivers/message/fusion/mptscsih.c
+++ b/drivers/message/fusion/mptscsih.c
--- a/drivers/message/fusion/mptscsih.h
+++ b/drivers/message/fusion/mptscsih.h
@@ -6,7 +6,7 @@
 *      running LSI Logic Fusion MPT (Message Passing Technology) firmware.
 *
 *  Copyright (c) 1999-2007 LSI Logic Corporation
- *  (mailto:mpt_linux_developer@lsil.com)
+ *  (mailto:mpt_linux_developer@lsi.com)
 *
 */
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
@@ -53,6 +53,24 @@
 *	SCSI Public stuff...
 */

+#define MPT_SCANDV_GOOD			(0x00000000) /* must be 0 */
+#define MPT_SCANDV_DID_RESET		(0x00000001)
+#define MPT_SCANDV_SENSE		(0x00000002)
+#define MPT_SCANDV_SOME_ERROR		(0x00000004)
+#define MPT_SCANDV_SELECTION_TIMEOUT	(0x00000008)
+#define MPT_SCANDV_ISSUE_SENSE		(0x00000010)
+#define MPT_SCANDV_FALLBACK		(0x00000020)
+
+#define MPT_SCANDV_MAX_RETRIES		(10)
+
+#define MPT_ICFLAG_BUF_CAP	0x01	/* ReadBuffer Read Capacity format */
+#define MPT_ICFLAG_ECHO		0x02	/* ReadBuffer Echo buffer format */
+#define MPT_ICFLAG_EBOS		0x04	/* ReadBuffer Echo buffer has EBOS */
+#define MPT_ICFLAG_PHYS_DISK	0x08	/* Any SCSI IO but do Phys Disk Format */
+#define MPT_ICFLAG_TAGGED_CMD	0x10	/* Do tagged IO */
+#define MPT_ICFLAG_DID_RESET	0x20	/* Bus Reset occurred with this command */
+#define MPT_ICFLAG_RESERVED	0x40	/* Reserved has been issued */
+
 #define MPT_SCSI_CMD_PER_DEV_HIGH	64
 #define MPT_SCSI_CMD_PER_DEV_LOW	32

@@ -69,9 +87,22 @@
 #define MPTSCSIH_SAF_TE                 0
 #define MPTSCSIH_PT_CLEAR               0

-
 #endif

+typedef struct _internal_cmd {
+	char		*data;		/* data pointer */
+	dma_addr_t	data_dma;	/* data dma address */
+	int		size;		/* transfer size */
+	u8		cmd;		/* SCSI Op Code */
+	u8		channel;	/* bus number */
+	u8		id;		/* SCSI ID (virtual) */
+	int		lun;
+	u8		flags;		/* Bit Field - See above */
+	u8		physDiskNum;	/* Phys disk number, -1 else */
+	u8		rsvd2;
+	u8		rsvd;
+} INTERNAL_CMD;
+
 extern void mptscsih_remove(struct pci_dev *);
 extern void mptscsih_shutdown(struct pci_dev *);
 #ifdef CONFIG_PM
@@ -81,9 +112,6 @@ extern int mptscsih_resume(struct pci_dev *pdev);
 extern int mptscsih_proc_info(struct Scsi_Host *host, char *buffer, char **start, off_t offset, int length, int func);
 extern const char * mptscsih_info(struct Scsi_Host *SChost);
 extern int mptscsih_qcmd(struct scsi_cmnd *SCpnt, void (*done)(struct scsi_cmnd *));
-extern int mptscsih_target_alloc(struct scsi_target *starget);
-extern int mptscsih_slave_alloc(struct scsi_device *device);
-extern void mptscsih_target_destroy(struct scsi_target *starget);
 extern void mptscsih_slave_destroy(struct scsi_device *device);
 extern int mptscsih_slave_configure(struct scsi_device *device);
 extern int mptscsih_abort(struct scsi_cmnd * SCpnt);
@@ -98,6 +126,6 @@ extern int mptscsih_event_process(MPT_ADAPTER *ioc, EventNotificationReply_t *pE
 extern int mptscsih_ioc_reset(MPT_ADAPTER *ioc, int post_reset);
 extern int mptscsih_change_queue_depth(struct scsi_device *sdev, int qdepth);
 extern void mptscsih_timer_expired(unsigned long data);
-extern int mptscsih_TMHandler(MPT_SCSI_HOST *hd, u8 type, u8 channel, u8 target, u8 lun, int ctx2abort, ulong timeout);
-extern int mptscsih_raid_id_to_num(MPT_SCSI_HOST *hd, uint physdiskid);
-extern int mptscsih_is_phys_disk(MPT_ADAPTER *ioc, int id);
+extern int mptscsih_TMHandler(MPT_SCSI_HOST *hd, u8 type, u8 channel, u8 id, int lun, int ctx2abort, ulong timeout);
+extern u8 mptscsih_raid_id_to_num(MPT_ADAPTER *ioc, u8 channel, u8 id);
+extern int mptscsih_is_phys_disk(MPT_ADAPTER *ioc, u8 channel, u8 id);
--- a/drivers/message/fusion/mptspi.c
+++ b/drivers/message/fusion/mptspi.c
--- a/drivers/s390/scsi/zfcp_erp.c
+++ b/drivers/s390/scsi/zfcp_erp.c
@@ -838,32 +838,28 @@ zfcp_erp_action_exists(struct zfcp_erp_action *erp_action)
 *		and does appropriate preparations (dismiss fsf request, ...)
 *
 * locks:	called under erp_lock (disabled interrupts)
- *
- * returns:	0
 */
-static int
+static void
 zfcp_erp_strategy_check_fsfreq(struct zfcp_erp_action *erp_action)
 {
-	int retval = 0;
-	struct zfcp_fsf_req *fsf_req = NULL;
 	struct zfcp_adapter *adapter = erp_action->adapter;

 	if (erp_action->fsf_req) {
 		/* take lock to ensure that request is not deleted meanwhile */
 		spin_lock(&adapter->req_list_lock);
-		if ((!zfcp_reqlist_ismember(adapter,
-					    erp_action->fsf_req->req_id)) &&
-		    (fsf_req->erp_action == erp_action)) {
+		if (zfcp_reqlist_ismember(adapter,
+					    erp_action->fsf_req->req_id)) {
 			/* fsf_req still exists */
 			debug_text_event(adapter->erp_dbf, 3, "a_ca_req");
-			debug_event(adapter->erp_dbf, 3, &fsf_req,
+			debug_event(adapter->erp_dbf, 3, &erp_action->fsf_req,
 				    sizeof (unsigned long));
 			/* dismiss fsf_req of timed out/dismissed erp_action */
 			if (erp_action->status & (ZFCP_STATUS_ERP_DISMISSED |
 						  ZFCP_STATUS_ERP_TIMEDOUT)) {
 				debug_text_event(adapter->erp_dbf, 3,
 						 "a_ca_disreq");
-				fsf_req->status |= ZFCP_STATUS_FSFREQ_DISMISSED;
+				erp_action->fsf_req->status |=
+					ZFCP_STATUS_FSFREQ_DISMISSED;
 			}
 			if (erp_action->status & ZFCP_STATUS_ERP_TIMEDOUT) {
 				ZFCP_LOG_NORMAL("error: erp step timed out "
@@ -876,11 +872,11 @@ zfcp_erp_strategy_check_fsfreq(struct zfcp_erp_action *erp_action)
 			 * then keep it running asynchronously and don't mess
 			 * with the association of erp_action and fsf_req.
 			 */
-			if (fsf_req->status & (ZFCP_STATUS_FSFREQ_COMPLETED |
+			if (erp_action->fsf_req->status &
+					(ZFCP_STATUS_FSFREQ_COMPLETED |
 					       ZFCP_STATUS_FSFREQ_DISMISSED)) {
 				/* forget about association between fsf_req
 				   and erp_action */
-				fsf_req->erp_action = NULL;
 				erp_action->fsf_req = NULL;
 			}
 		} else {
@@ -894,8 +890,6 @@ zfcp_erp_strategy_check_fsfreq(struct zfcp_erp_action *erp_action)
 		spin_unlock(&adapter->req_list_lock);
 	} else
 		debug_text_event(adapter->erp_dbf, 3, "a_ca_noreq");
-
-	return retval;
 }

 /**

--- a/drivers/s390/scsi/zfcp_ext.h
+++ b/drivers/s390/scsi/zfcp_ext.h
@@ -89,7 +89,7 @@ extern int  zfcp_fsf_control_file(struct zfcp_adapter *, struct zfcp_fsf_req **,
 				  u32, u32, struct zfcp_sg_list *);
 extern void zfcp_fsf_start_timer(struct zfcp_fsf_req *, unsigned long);
 extern void zfcp_erp_start_timer(struct zfcp_fsf_req *);
-extern int  zfcp_fsf_req_dismiss_all(struct zfcp_adapter *);
+extern void zfcp_fsf_req_dismiss_all(struct zfcp_adapter *);
 extern int  zfcp_fsf_status_read(struct zfcp_adapter *, int);
 extern int zfcp_fsf_req_create(struct zfcp_adapter *, u32, int, mempool_t *,
 			       unsigned long *, struct zfcp_fsf_req **);

--- a/drivers/s390/scsi/zfcp_fsf.c
+++ b/drivers/s390/scsi/zfcp_fsf.c
@@ -176,28 +176,25 @@ static void zfcp_fsf_req_dismiss(struct zfcp_adapter *adapter,
 /**
 * zfcp_fsf_req_dismiss_all - dismiss all remaining fsf requests
 */
-int zfcp_fsf_req_dismiss_all(struct zfcp_adapter *adapter)
+void zfcp_fsf_req_dismiss_all(struct zfcp_adapter *adapter)
 {
 	struct zfcp_fsf_req *request, *tmp;
 	unsigned long flags;
+	LIST_HEAD(remove_queue);
 	unsigned int i, counter;

 	spin_lock_irqsave(&adapter->req_list_lock, flags);
 	atomic_set(&adapter->reqs_active, 0);
-	for (i=0; i<REQUEST_LIST_SIZE; i++) {
-		if (list_empty(&adapter->req_list[i]))
-			continue;
-
-		counter = 0;
-		list_for_each_entry_safe(request, tmp,
-					 &adapter->req_list[i], list) {
-			zfcp_fsf_req_dismiss(adapter, request, counter);
-			counter++;
-		}
-	}
+	for (i=0; i<REQUEST_LIST_SIZE; i++)
+		list_splice_init(&adapter->req_list[i], &remove_queue);
+
 	spin_unlock_irqrestore(&adapter->req_list_lock, flags);

-	return 0;
+	counter = 0;
+	list_for_each_entry_safe(request, tmp, &remove_queue, list) {
+		zfcp_fsf_req_dismiss(adapter, request, counter);
+		counter++;
+	}
 }

 /*

--- a/drivers/scsi/53c700.c
+++ b/drivers/scsi/53c700.c
@@ -667,12 +667,30 @@ NCR_700_chip_setup(struct Scsi_Host *host)
 	__u8 min_xferp = (hostdata->chip710 ? NCR_710_MIN_XFERP : NCR_700_MIN_XFERP);

 	if(hostdata->chip710) {
-		__u8 burst_disable = hostdata->burst_disable
-			? BURST_DISABLE : 0;
+		__u8 burst_disable = 0;
+		__u8 burst_length = 0;
+
+		switch (hostdata->burst_length) {
+			case 1:
+			        burst_length = BURST_LENGTH_1;
+			        break;
+			case 2:
+			        burst_length = BURST_LENGTH_2;
+			        break;
+			case 4:
+			        burst_length = BURST_LENGTH_4;
+			        break;
+			case 8:
+			        burst_length = BURST_LENGTH_8;
+			        break;
+			default:
+			        burst_disable = BURST_DISABLE;
+			        break;
+		}
 		dcntl_extra = COMPAT_700_MODE;

 		NCR_700_writeb(dcntl_extra, host, DCNTL_REG);
-		NCR_700_writeb(BURST_LENGTH_8  | hostdata->dmode_extra,
+		NCR_700_writeb(burst_length | hostdata->dmode_extra,
 			       host, DMODE_710_REG);
 		NCR_700_writeb(burst_disable | (hostdata->differential ? 
 						DIFF : 0), host, CTEST7_REG);

--- a/drivers/scsi/53c700.h
+++ b/drivers/scsi/53c700.h
@@ -203,7 +203,7 @@ struct NCR_700_Host_Parameters {
 	__u32	force_le_on_be:1;
 #endif
 	__u32	chip710:1;	/* set if really a 710 not 700 */
-	__u32	burst_disable:1;	/* set to 1 to disable 710 bursting */
+	__u32	burst_length:4;	/* set to 0 to disable 710 bursting */

 	/* NOTHING BELOW HERE NEEDS ALTERING */
 	__u32	fast:1;		/* if we can alter the SCSI bus clock

--- a/drivers/scsi/53c7xx.c
+++ b/drivers/scsi/53c7xx.c
@@ -4399,7 +4399,7 @@ abort_connected (struct Scsi_Host *host) {
 * account the current synchronous offset) 
 */

-    sstat = (NCR53c8x0_read8 (SSTAT2_REG);
+    sstat = NCR53c8x0_read8 (SSTAT2_REG);
    offset = OFFSET (sstat & SSTAT2_FF_MASK) >> SSTAT2_FF_SHIFT;
    phase = sstat & SSTAT2_PHASE_MASK;

@@ -5422,7 +5422,7 @@ insn_to_offset (Scsi_Cmnd *cmd, u32 *insn) {
    	    	     --buffers, offset += segment->length, ++segment)
 #if 0
 		    printk("scsi%d: comparing 0x%p to 0x%p\n", 
-			cmd->device->host->host_no, saved, page_address(segment->page+segment->offset);
+			cmd->device->host->host_no, saved, page_address(segment->page+segment->offset));
 #else
 		    ;
 #endif

--- a/drivers/scsi/BusLogic.c
+++ b/drivers/scsi/BusLogic.c
@@ -192,7 +192,7 @@ static void BusLogic_InitializeCCBs(struct BusLogic_HostAdapter *HostAdapter, vo
  BusLogic_CreateInitialCCBs allocates the initial CCBs for Host Adapter.
 */

-static boolean __init BusLogic_CreateInitialCCBs(struct BusLogic_HostAdapter *HostAdapter)
+static bool __init BusLogic_CreateInitialCCBs(struct BusLogic_HostAdapter *HostAdapter)
 {
 	int BlockSize = BusLogic_CCB_AllocationGroupSize * sizeof(struct BusLogic_CCB);
 	void *BlockPointer;
@@ -238,7 +238,7 @@ static void BusLogic_DestroyCCBs(struct BusLogic_HostAdapter *HostAdapter)
  multiple host adapters share the same IRQ Channel.
 */

-static void BusLogic_CreateAdditionalCCBs(struct BusLogic_HostAdapter *HostAdapter, int AdditionalCCBs, boolean SuccessMessageP)
+static void BusLogic_CreateAdditionalCCBs(struct BusLogic_HostAdapter *HostAdapter, int AdditionalCCBs, bool SuccessMessageP)
 {
 	int BlockSize = BusLogic_CCB_AllocationGroupSize * sizeof(struct BusLogic_CCB);
 	int PreviouslyAllocated = HostAdapter->AllocatedCCBs;
@@ -362,10 +362,8 @@ static int BusLogic_Command(struct BusLogic_HostAdapter *HostAdapter, enum BusLo
 	   interrupt could occur if the IRQ Channel was previously enabled by another
 	   BusLogic Host Adapter or another driver sharing the same IRQ Channel.
 	 */
-	if (!HostAdapter->IRQ_ChannelAcquired) {
+	if (!HostAdapter->IRQ_ChannelAcquired)
 		local_irq_save(ProcessorFlags);
-		local_irq_disable();
-	}
 	/*
 	   Wait for the Host Adapter Ready bit to be set and the Command/Parameter
 	   Register Busy bit to be reset in the Status Register.
@@ -639,9 +637,9 @@ static int __init BusLogic_InitializeMultiMasterProbeInfo(struct BusLogic_HostAd
 	struct BusLogic_ProbeInfo *PrimaryProbeInfo = &BusLogic_ProbeInfoList[BusLogic_ProbeInfoCount];
 	int NonPrimaryPCIMultiMasterIndex = BusLogic_ProbeInfoCount + 1;
 	int NonPrimaryPCIMultiMasterCount = 0, PCIMultiMasterCount = 0;
-	boolean ForceBusDeviceScanningOrder = false;
-	boolean ForceBusDeviceScanningOrderChecked = false;
-	boolean StandardAddressSeen[6];
+	bool ForceBusDeviceScanningOrder = false;
+	bool ForceBusDeviceScanningOrderChecked = false;
+	bool StandardAddressSeen[6];
 	struct pci_dev *PCI_Device = NULL;
 	int i;
 	if (BusLogic_ProbeInfoCount >= BusLogic_MaxHostAdapters)
@@ -1011,7 +1009,7 @@ static void __init BusLogic_InitializeProbeInfoList(struct BusLogic_HostAdapter
  BusLogic_Failure prints a standardized error message, and then returns false.
 */

-static boolean BusLogic_Failure(struct BusLogic_HostAdapter *HostAdapter, char *ErrorMessage)
+static bool BusLogic_Failure(struct BusLogic_HostAdapter *HostAdapter, char *ErrorMessage)
 {
 	BusLogic_AnnounceDriver(HostAdapter);
 	if (HostAdapter->HostAdapterBusType == BusLogic_PCI_Bus) {
@@ -1030,7 +1028,7 @@ static boolean BusLogic_Failure(struct BusLogic_HostAdapter *HostAdapter, char *
  BusLogic_ProbeHostAdapter probes for a BusLogic Host Adapter.
 */

-static boolean __init BusLogic_ProbeHostAdapter(struct BusLogic_HostAdapter *HostAdapter)
+static bool __init BusLogic_ProbeHostAdapter(struct BusLogic_HostAdapter *HostAdapter)
 {
 	union BusLogic_StatusRegister StatusRegister;
 	union BusLogic_InterruptRegister InterruptRegister;
@@ -1101,8 +1099,8 @@ static boolean __init BusLogic_ProbeHostAdapter(struct BusLogic_HostAdapter *Hos
  SCSI Bus Reset.
 */

-static boolean BusLogic_HardwareResetHostAdapter(struct BusLogic_HostAdapter
-						 *HostAdapter, boolean HardReset)
+static bool BusLogic_HardwareResetHostAdapter(struct BusLogic_HostAdapter
+						 *HostAdapter, bool HardReset)
 {
 	union BusLogic_StatusRegister StatusRegister;
 	int TimeoutCounter;
@@ -1205,11 +1203,11 @@ static boolean BusLogic_HardwareResetHostAdapter(struct BusLogic_HostAdapter
  Host Adapter.
 */

-static boolean __init BusLogic_CheckHostAdapter(struct BusLogic_HostAdapter *HostAdapter)
+static bool __init BusLogic_CheckHostAdapter(struct BusLogic_HostAdapter *HostAdapter)
 {
 	struct BusLogic_ExtendedSetupInformation ExtendedSetupInformation;
 	unsigned char RequestedReplyLength;
-	boolean Result = true;
+	bool Result = true;
 	/*
 	   FlashPoint Host Adapters do not require this protection.
 	 */
@@ -1239,7 +1237,7 @@ static boolean __init BusLogic_CheckHostAdapter(struct BusLogic_HostAdapter *Hos
  from Host Adapter and initializes the Host Adapter structure.
 */

-static boolean __init BusLogic_ReadHostAdapterConfiguration(struct BusLogic_HostAdapter
+static bool __init BusLogic_ReadHostAdapterConfiguration(struct BusLogic_HostAdapter
 							    *HostAdapter)
 {
 	struct BusLogic_BoardID BoardID;
@@ -1686,14 +1684,14 @@ static boolean __init BusLogic_ReadHostAdapterConfiguration(struct BusLogic_Host
  Host Adapter.
 */

-static boolean __init BusLogic_ReportHostAdapterConfiguration(struct BusLogic_HostAdapter
+static bool __init BusLogic_ReportHostAdapterConfiguration(struct BusLogic_HostAdapter
 							      *HostAdapter)
 {
 	unsigned short AllTargetsMask = (1 << HostAdapter->MaxTargetDevices) - 1;
 	unsigned short SynchronousPermitted, FastPermitted;
 	unsigned short UltraPermitted, WidePermitted;
 	unsigned short DisconnectPermitted, TaggedQueuingPermitted;
-	boolean CommonSynchronousNegotiation, CommonTaggedQueueDepth;
+	bool CommonSynchronousNegotiation, CommonTaggedQueueDepth;
 	char SynchronousString[BusLogic_MaxTargetDevices + 1];
 	char WideString[BusLogic_MaxTargetDevices + 1];
 	char DisconnectString[BusLogic_MaxTargetDevices + 1];
@@ -1835,7 +1833,7 @@ static boolean __init BusLogic_ReportHostAdapterConfiguration(struct BusLogic_Ho
  Host Adapter.
 */

-static boolean __init BusLogic_AcquireResources(struct BusLogic_HostAdapter *HostAdapter)
+static bool __init BusLogic_AcquireResources(struct BusLogic_HostAdapter *HostAdapter)
 {
 	if (HostAdapter->IRQ_Channel == 0) {
 		BusLogic_Error("NO LEGAL INTERRUPT CHANNEL ASSIGNED - DETACHING\n", HostAdapter);
@@ -1903,7 +1901,7 @@ static void BusLogic_ReleaseResources(struct BusLogic_HostAdapter *HostAdapter)
  of the Host Adapter from its initial power on or hard reset state.
 */

-static boolean BusLogic_InitializeHostAdapter(struct BusLogic_HostAdapter
+static bool BusLogic_InitializeHostAdapter(struct BusLogic_HostAdapter
 					      *HostAdapter)
 {
 	struct BusLogic_ExtendedMailboxRequest ExtendedMailboxRequest;
@@ -2002,7 +2000,7 @@ static boolean BusLogic_InitializeHostAdapter(struct BusLogic_HostAdapter
  through Host Adapter.
 */

-static boolean __init BusLogic_TargetDeviceInquiry(struct BusLogic_HostAdapter
+static bool __init BusLogic_TargetDeviceInquiry(struct BusLogic_HostAdapter
 						   *HostAdapter)
 {
 	u16 InstalledDevices;
@@ -2739,7 +2737,7 @@ static irqreturn_t BusLogic_InterruptHandler(int IRQ_Channel, void *DeviceIdenti
  already have been acquired by the caller.
 */

-static boolean BusLogic_WriteOutgoingMailbox(struct BusLogic_HostAdapter
+static bool BusLogic_WriteOutgoingMailbox(struct BusLogic_HostAdapter
 					     *HostAdapter, enum BusLogic_ActionCode ActionCode, struct BusLogic_CCB *CCB)
 {
 	struct BusLogic_OutgoingMailbox *NextOutgoingMailbox;
@@ -3058,7 +3056,7 @@ static int BusLogic_AbortCommand(struct scsi_cmnd *Command)
  currently executing SCSI Commands as having been Reset.
 */

-static int BusLogic_ResetHostAdapter(struct BusLogic_HostAdapter *HostAdapter, boolean HardReset)
+static int BusLogic_ResetHostAdapter(struct BusLogic_HostAdapter *HostAdapter, bool HardReset)
 {
 	struct BusLogic_CCB *CCB;
 	int TargetID;
@@ -3309,7 +3307,7 @@ Target	Requested Completed  Requested Completed  Requested Completed\n\
 static void BusLogic_Message(enum BusLogic_MessageLevel MessageLevel, char *Format, struct BusLogic_HostAdapter *HostAdapter, ...)
 {
 	static char Buffer[BusLogic_LineBufferSize];
-	static boolean BeginningOfLine = true;
+	static bool BeginningOfLine = true;
 	va_list Arguments;
 	int Length = 0;
 	va_start(Arguments, HostAdapter);
@@ -3347,7 +3345,7 @@ static void BusLogic_Message(enum BusLogic_MessageLevel MessageLevel, char *Form
  and updates the pointer if the keyword is recognized and false otherwise.
 */

-static boolean __init BusLogic_ParseKeyword(char **StringPointer, char *Keyword)
+static bool __init BusLogic_ParseKeyword(char **StringPointer, char *Keyword)
 {
 	char *Pointer = *StringPointer;
 	while (*Keyword != '\0') {

--- a/drivers/scsi/BusLogic.h
+++ b/drivers/scsi/BusLogic.h
--- a/drivers/scsi/FlashPoint.c
+++ b/drivers/scsi/FlashPoint.c
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -124,6 +124,7 @@ obj-$(CONFIG_JAZZ_ESP)		+= NCR53C9x.o	jazz_esp.o
 obj-$(CONFIG_SUN3X_ESP)		+= NCR53C9x.o	sun3x_esp.o
 obj-$(CONFIG_SCSI_FCAL)		+= fcal.o
 obj-$(CONFIG_SCSI_LASI700)	+= 53c700.o lasi700.o
+obj-$(CONFIG_SCSI_SNI_53C710)	+= 53c700.o sni_53c710.o
 obj-$(CONFIG_SCSI_NSP32)	+= nsp32.o
 obj-$(CONFIG_SCSI_IPR)		+= ipr.o
 obj-$(CONFIG_SCSI_SRP)		+= libsrp.o

--- a/drivers/scsi/NCR_D700.c
+++ b/drivers/scsi/NCR_D700.c
@@ -200,6 +200,7 @@ NCR_D700_probe_one(struct NCR_D700_private *p, int siop, int irq,
 	hostdata->base = ioport_map(region, 64);
 	hostdata->differential = (((1<<siop) & differential) != 0);
 	hostdata->clock = NCR_D700_CLOCK_MHZ;
+	hostdata->burst_length = 8;

 	/* and register the siop */
 	host = NCR_700_detect(&NCR_D700_driver_template, hostdata, p->dev);

--- a/drivers/scsi/aacraid/Makefile
+++ b/drivers/scsi/aacraid/Makefile
--- a/drivers/scsi/aacraid/aachba.c
+++ b/drivers/scsi/aacraid/aachba.c
--- a/drivers/scsi/aacraid/aacraid.h
+++ b/drivers/scsi/aacraid/aacraid.h
--- a/drivers/scsi/aacraid/comminit.c
+++ b/drivers/scsi/aacraid/comminit.c
--- a/drivers/scsi/aacraid/commsup.c
+++ b/drivers/scsi/aacraid/commsup.c
--- a/drivers/scsi/aacraid/linit.c
+++ b/drivers/scsi/aacraid/linit.c
--- a/drivers/scsi/aacraid/nark.c
+++ b/drivers/scsi/aacraid/nark.c
--- a/drivers/scsi/aacraid/rkt.c
+++ b/drivers/scsi/aacraid/rkt.c
--- a/drivers/scsi/aacraid/rx.c
+++ b/drivers/scsi/aacraid/rx.c
--- a/drivers/scsi/aacraid/sa.c
+++ b/drivers/scsi/aacraid/sa.c
--- a/drivers/scsi/advansys.c
+++ b/drivers/scsi/advansys.c
--- a/drivers/scsi/aic7xxx/aic79xx.h
+++ b/drivers/scsi/aic7xxx/aic79xx.h
--- a/drivers/scsi/aic7xxx/aic79xx_core.c
+++ b/drivers/scsi/aic7xxx/aic79xx_core.c
--- a/drivers/scsi/aic7xxx/aic79xx_osm.c
+++ b/drivers/scsi/aic7xxx/aic79xx_osm.c
--- a/drivers/scsi/aic7xxx/aic79xx_osm.h
+++ b/drivers/scsi/aic7xxx/aic79xx_osm.h
--- a/drivers/scsi/aic7xxx/aic79xx_osm_pci.c
+++ b/drivers/scsi/aic7xxx/aic79xx_osm_pci.c
--- a/drivers/scsi/aic7xxx/aic79xx_pci.c
+++ b/drivers/scsi/aic7xxx/aic79xx_pci.c
--- a/drivers/scsi/aic94xx/aic94xx_dev.c
+++ b/drivers/scsi/aic94xx/aic94xx_dev.c
--- a/drivers/scsi/aic94xx/aic94xx_dump.c
+++ b/drivers/scsi/aic94xx/aic94xx_dump.c
--- a/drivers/scsi/aic94xx/aic94xx_init.c
+++ b/drivers/scsi/aic94xx/aic94xx_init.c
--- a/drivers/scsi/aic94xx/aic94xx_reg_def.h
+++ b/drivers/scsi/aic94xx/aic94xx_reg_def.h
--- a/drivers/scsi/aic94xx/aic94xx_sas.h
+++ b/drivers/scsi/aic94xx/aic94xx_sas.h
--- a/drivers/scsi/aic94xx/aic94xx_scb.c
+++ b/drivers/scsi/aic94xx/aic94xx_scb.c
--- a/drivers/scsi/aic94xx/aic94xx_sds.c
+++ b/drivers/scsi/aic94xx/aic94xx_sds.c
--- a/drivers/scsi/aic94xx/aic94xx_seq.c
+++ b/drivers/scsi/aic94xx/aic94xx_seq.c
--- a/drivers/scsi/aic94xx/aic94xx_seq.h
+++ b/drivers/scsi/aic94xx/aic94xx_seq.h
--- a/drivers/scsi/aic94xx/aic94xx_task.c
+++ b/drivers/scsi/aic94xx/aic94xx_task.c
--- a/drivers/scsi/aic94xx/aic94xx_tmf.c
+++ b/drivers/scsi/aic94xx/aic94xx_tmf.c
--- a/drivers/scsi/ipr.c
+++ b/drivers/scsi/ipr.c
--- a/drivers/scsi/ipr.h
+++ b/drivers/scsi/ipr.h
--- a/drivers/scsi/lasi700.c
+++ b/drivers/scsi/lasi700.c
--- a/drivers/scsi/libsas/sas_discover.c
+++ b/drivers/scsi/libsas/sas_discover.c
--- a/drivers/scsi/libsas/sas_event.c
+++ b/drivers/scsi/libsas/sas_event.c
--- a/drivers/scsi/libsas/sas_expander.c
+++ b/drivers/scsi/libsas/sas_expander.c
--- a/drivers/scsi/libsas/sas_init.c
+++ b/drivers/scsi/libsas/sas_init.c
--- a/drivers/scsi/libsas/sas_internal.h
+++ b/drivers/scsi/libsas/sas_internal.h
--- a/drivers/scsi/libsas/sas_port.c
+++ b/drivers/scsi/libsas/sas_port.c
--- a/drivers/scsi/libsas/sas_scsi_host.c
+++ b/drivers/scsi/libsas/sas_scsi_host.c
--- a/drivers/scsi/megaraid/mbox_defs.h
+++ b/drivers/scsi/megaraid/mbox_defs.h
--- a/drivers/scsi/megaraid/mega_common.h
+++ b/drivers/scsi/megaraid/mega_common.h
--- a/drivers/scsi/megaraid/megaraid_ioctl.h
+++ b/drivers/scsi/megaraid/megaraid_ioctl.h
--- a/drivers/scsi/megaraid/megaraid_mbox.c
+++ b/drivers/scsi/megaraid/megaraid_mbox.c
--- a/drivers/scsi/megaraid/megaraid_mbox.h
+++ b/drivers/scsi/megaraid/megaraid_mbox.h
--- a/drivers/scsi/megaraid/megaraid_mm.c
+++ b/drivers/scsi/megaraid/megaraid_mm.c
--- a/drivers/scsi/megaraid/megaraid_sas.h
+++ b/drivers/scsi/megaraid/megaraid_sas.h
--- a/drivers/scsi/pcmcia/nsp_cs.h
+++ b/drivers/scsi/pcmcia/nsp_cs.h
--- a/drivers/scsi/qla2xxx/qla_attr.c
+++ b/drivers/scsi/qla2xxx/qla_attr.c
--- a/drivers/scsi/qla2xxx/qla_def.h
+++ b/drivers/scsi/qla2xxx/qla_def.h
--- a/drivers/scsi/qla2xxx/qla_gbl.h
+++ b/drivers/scsi/qla2xxx/qla_gbl.h
--- a/drivers/scsi/qla2xxx/qla_init.c
+++ b/drivers/scsi/qla2xxx/qla_init.c
--- a/drivers/scsi/qla2xxx/qla_isr.c
+++ b/drivers/scsi/qla2xxx/qla_isr.c
--- a/drivers/scsi/qla2xxx/qla_mbx.c
+++ b/drivers/scsi/qla2xxx/qla_mbx.c
--- a/drivers/scsi/qla2xxx/qla_os.c
+++ b/drivers/scsi/qla2xxx/qla_os.c
--- a/drivers/scsi/qla2xxx/qla_sup.c
+++ b/drivers/scsi/qla2xxx/qla_sup.c
--- a/drivers/scsi/qla2xxx/qla_version.h
+++ b/drivers/scsi/qla2xxx/qla_version.h
--- a/drivers/scsi/scsi.c
+++ b/drivers/scsi/scsi.c
--- a/drivers/scsi/scsi_debug.c
+++ b/drivers/scsi/scsi_debug.c
--- a/drivers/scsi/scsi_error.c
+++ b/drivers/scsi/scsi_error.c
--- a/drivers/scsi/scsi_lib.c
+++ b/drivers/scsi/scsi_lib.c
--- a/drivers/scsi/scsi_priv.h
+++ b/drivers/scsi/scsi_priv.h
--- a/drivers/scsi/scsi_scan.c
+++ b/drivers/scsi/scsi_scan.c
--- a/drivers/scsi/scsi_transport_sas.c
+++ b/drivers/scsi/scsi_transport_sas.c
--- a/drivers/scsi/scsi_transport_spi.c
+++ b/drivers/scsi/scsi_transport_spi.c
--- a/drivers/scsi/sim710.c
+++ b/drivers/scsi/sim710.c
--- a/drivers/scsi/sni_53c710.c
+++ b/drivers/scsi/sni_53c710.c
--- a/drivers/scsi/st.c
+++ b/drivers/scsi/st.c
--- a/drivers/scsi/st.h
+++ b/drivers/scsi/st.h
--- a/include/scsi/libsas.h
+++ b/include/scsi/libsas.h
--- a/include/scsi/scsi_transport_sas.h
+++ b/include/scsi/scsi_transport_sas.h
--- a/include/scsi/scsi_transport_spi.h
+++ b/include/scsi/scsi_transport_spi.h