Sliceup Kconfig; it's grown too large.

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

arch/mips/ddb5xxx/Kconfig

+config DDB5477_BUS_FREQUENCY
+	int "bus frequency (in kHZ, 0 for auto-detect)"
+	depends on DDB5477
+	default 0

arch/mips/gt64120/ev64120/Kconfig

+config EVB_PCI1
+	bool "Enable Second PCI (PCI1)"
+	depends on MIPS_EV64120

arch/mips/ite-boards/Kconfig

+config IT8172_REVC
+	bool "Support for older IT8172 (Rev C)"
+	depends on MIPS_ITE8172
+	help
+	  Say Y here to support the older, Revision C version of the Integrated
+	  Technology Express, Inc. ITE8172 SBC.  Vendor page at
+	  <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
+	  board at <http://www.mvista.com/partners/semiconductor/ite.html>.

arch/mips/jazz/Kconfig

+config ACER_PICA_61
+	bool "Support for Acer PICA 1 chipset (EXPERIMENTAL)"
+	depends on MACH_JAZZ && EXPERIMENTAL
+	select DMA_NONCOHERENT
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	help
+	  This is a machine with a R4400 133/150 MHz CPU. To compile a Linux
+	  kernel that runs on these, say Y here. For details about Linux on
+	  the MIPS architecture, check out the Linux/MIPS FAQ on the WWW at
+	  <http://www.linux-mips.org/>.
+
+config MIPS_MAGNUM_4000
+	bool "Support for MIPS Magnum 4000"
+	depends on MACH_JAZZ
+	select DMA_NONCOHERENT
+	select SYS_SUPPORTS_BIG_ENDIAN if EXPERIMENTAL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	help
+	  This is a machine with a R4000 100 MHz CPU. To compile a Linux
+	  kernel that runs on these, say Y here. For details about Linux on
+	  the MIPS architecture, check out the Linux/MIPS FAQ on the WWW at
+	  <http://www.linux-mips.org/>.
+
+config OLIVETTI_M700
+	bool "Support for Olivetti M700-10"
+	depends on MACH_JAZZ
+	select DMA_NONCOHERENT
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	help
+	  This is a machine with a R4000 100 MHz CPU. To compile a Linux
+	  kernel that runs on these, say Y here. For details about Linux on
+	  the MIPS architecture, check out the Linux/MIPS FAQ on the WWW at
+	  <http://www.linux-mips.org/>.

arch/mips/lasat/Kconfig

+config PICVUE
+	tristate "PICVUE LCD display driver"
+	depends on LASAT
+
+config PICVUE_PROC
+	tristate "PICVUE LCD display driver /proc interface"
+	depends on PICVUE
+
+config DS1603
+	bool "DS1603 RTC driver"
+	depends on LASAT
+
+config LASAT_SYSCTL
+	bool "LASAT sysctl interface"
+	depends on LASAT

arch/mips/momentum/Kconfig

+config JAGUAR_DMALOW
+	bool "Low DMA Mode"
+	depends on MOMENCO_JAGUAR_ATX
+	help
+	  Select to Y if jump JP5 is set on your board, N otherwise.  Normally
+	  the jumper is set, so if you feel unsafe, just say Y.

arch/mips/pmc-sierra/Kconfig

+config HYPERTRANSPORT
+	bool "Hypertransport Support for PMC-Sierra Yosemite"
+	depends on PMC_YOSEMITE

arch/mips/tx4927/Kconfig

+config TOSHIBA_FPCIB0
+	bool "FPCIB0 Backplane Support"
+	depends on TOSHIBA_RBTX4927

arch/mips/vr41xx/Kconfig

+config CASIO_E55
+	bool "Support for CASIO CASSIOPEIA E-10/15/55/65"
+	depends on MACH_VR41XX
+	select DMA_NONCOHERENT
+	select IRQ_CPU
+	select ISA
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
+config IBM_WORKPAD
+	bool "Support for IBM WorkPad z50"
+	depends on MACH_VR41XX
+	select DMA_NONCOHERENT
+	select IRQ_CPU
+	select ISA
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
+config NEC_CMBVR4133
+	bool "Support for NEC CMB-VR4133"
+	depends on MACH_VR41XX
+	select CPU_VR41XX
+	select DMA_NONCOHERENT
+	select IRQ_CPU
+	select HW_HAS_PCI
+
+config ROCKHOPPER
+	bool "Support for Rockhopper baseboard"
+	depends on NEC_CMBVR4133
+	select I8259
+	select HAVE_STD_PC_SERIAL_PORT
+
+config TANBAC_TB022X
+	bool "Support for TANBAC VR4131 multichip module and TANBAC VR4131DIMM"
+	depends on MACH_VR41XX
+	select DMA_NONCOHERENT
+	select HW_HAS_PCI
+	select IRQ_CPU
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	help
+	  The TANBAC VR4131 multichip module(TB0225) and
+	  the TANBAC VR4131DIMM(TB0229) are MIPS-based platforms
+	  manufactured by TANBAC.
+	  Please refer to <http://www.tanbac.co.jp/>
+	  about VR4131 multichip module and VR4131DIMM.
+
+config TANBAC_TB0226
+	bool "Support for TANBAC Mbase(TB0226)"
+	depends on TANBAC_TB022X
+	select GPIO_VR41XX
+	help
+	  The TANBAC Mbase(TB0226) is a MIPS-based platform
+	  manufactured by TANBAC.
+	  Please refer to <http://www.tanbac.co.jp/> about Mbase.
+
+config TANBAC_TB0287
+	bool "Support for TANBAC Mini-ITX DIMM base(TB0287)"
+	depends on TANBAC_TB022X
+	help
+	  The TANBAC Mini-ITX DIMM base(TB0287) is a MIPS-based platform
+	  manufactured by TANBAC.
+	  Please refer to <http://www.tanbac.co.jp/> about Mini-ITX DIMM base.
+
+config VICTOR_MPC30X
+	bool "Support for Victor MP-C303/304"
+	depends on MACH_VR41XX
+	select DMA_NONCOHERENT
+	select HW_HAS_PCI
+	select IRQ_CPU
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
+config ZAO_CAPCELLA
+	bool "Support for ZAO Networks Capcella"
+	depends on MACH_VR41XX
+	select DMA_NONCOHERENT
+	select HW_HAS_PCI
+	select IRQ_CPU
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
+config PCI_VR41XX
+	bool "Add PCI control unit support of NEC VR4100 series"
+	depends on MACH_VR41XX && HW_HAS_PCI
+	default y
+	select PCI
+
+config VRC4173
+	tristate "Add NEC VRC4173 companion chip support"
+	depends on MACH_VR41XX && PCI_VR41XX
+	help
+	  The NEC VRC4173 is a companion chip for NEC VR4122/VR4131.