xhci: USB 3.1 add default Speed Attributes to SuperSpeedPlus device capability

If a xhci controller does not provide a protocol speed ID (PSI) table, a
default one should be used instead. Add the default values to the
SuperSpeedPlus device capability. Overwrite the default ones if a PSI table
exists. See xHCI 1.1 sectio 7.2.2.1.1 for more info
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/host/xhci-hub.c

@@ -50,14 +50,18 @@ static u8 usb_bos_descriptor [] = {
 	0x00,				/* bU1DevExitLat, set later. */
 	0x00, 0x00,			/* __le16 bU2DevExitLat, set later. */
 	/* Second device capability, SuperSpeedPlus */
-	0x0c,				/* bLength 12, will be adjusted later */
+	0x1c,				/* bLength 28, will be adjusted later */
 	USB_DT_DEVICE_CAPABILITY,	/* Device Capability */
 	USB_SSP_CAP_TYPE,		/* bDevCapabilityType SUPERSPEED_PLUS */
 	0x00,				/* bReserved 0 */
-	0x00, 0x00, 0x00, 0x00,		/* bmAttributes, get from xhci psic */
-	0x00, 0x00,			/* wFunctionalitySupport */
+	0x23, 0x00, 0x00, 0x00,		/* bmAttributes, SSAC=3 SSIC=1 */
+	0x01, 0x00,			/* wFunctionalitySupport */
 	0x00, 0x00,			/* wReserved 0 */
-	/* Sublink Speed Attributes are added in xhci_create_usb3_bos_desc() */
+	/* Default Sublink Speed Attributes, overwrite if custom PSI exists */
+	0x34, 0x00, 0x05, 0x00,		/* 5Gbps, symmetric, rx, ID = 4 */
+	0xb4, 0x00, 0x05, 0x00,		/* 5Gbps, symmetric, tx, ID = 4 */
+	0x35, 0x40, 0x0a, 0x00,		/* 10Gbps, SSP, symmetric, rx, ID = 5 */
+	0xb5, 0x40, 0x0a, 0x00,		/* 10Gbps, SSP, symmetric, tx, ID = 5 */
 };
 
 static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
@@ -72,10 +76,14 @@ static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
 	ssp_cap_size = sizeof(usb_bos_descriptor) - desc_size;
 
 	/* does xhci support USB 3.1 Enhanced SuperSpeed */
-	if (xhci->usb3_rhub.min_rev >= 0x01 && xhci->usb3_rhub.psi_uid_count) {
-		/* two SSA entries for each unique PSI ID, one RX and one TX */
-		ssa_count = xhci->usb3_rhub.psi_uid_count * 2;
-		ssa_size = ssa_count * sizeof(u32);
+	if (xhci->usb3_rhub.min_rev >= 0x01) {
+		/* does xhci provide a PSI table for SSA speed attributes? */
+		if (xhci->usb3_rhub.psi_count) {
+			/* two SSA entries for each unique PSI ID, RX and TX */
+			ssa_count = xhci->usb3_rhub.psi_uid_count * 2;
+			ssa_size = ssa_count * sizeof(u32);
+			ssp_cap_size -= 16; /* skip copying the default SSA */
+		}
 		desc_size += ssp_cap_size;
 		usb3_1 = true;
 	}
@@ -102,7 +110,8 @@ static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
 		put_unaligned_le16(HCS_U2_LATENCY(temp), &buf[13]);
 	}
 
-	if (usb3_1) {
+	/* If PSI table exists, add the custom speed attributes from it */
+	if (usb3_1 && xhci->usb3_rhub.psi_count) {
 		u32 ssp_cap_base, bm_attrib, psi;
 		int offset;