提交 5ca6f7c8 编写于 作者: D David S. Miller
......@@ -48,6 +48,7 @@
#include <linux/netdevice.h>
#include <linux/cache.h>
#include <linux/pci.h>
#include <linux/pci-aspm.h>
#include <linux/ethtool.h>
#include <linux/uaccess.h>
#include <linux/slab.h>
......@@ -476,6 +477,26 @@ ath5k_pci_probe(struct pci_dev *pdev,
int ret;
u8 csz;
/*
* L0s needs to be disabled on all ath5k cards.
*
* For distributions shipping with CONFIG_PCIEASPM (this will be enabled
* by default in the future in 2.6.36) this will also mean both L1 and
* L0s will be disabled when a pre 1.1 PCIe device is detected. We do
* know L1 works correctly even for all ath5k pre 1.1 PCIe devices
* though but cannot currently undue the effect of a blacklist, for
* details you can read pcie_aspm_sanity_check() and see how it adjusts
* the device link capability.
*
* It may be possible in the future to implement some PCI API to allow
* drivers to override blacklists for pre 1.1 PCIe but for now it is
* best to accept that both L0s and L1 will be disabled completely for
* distributions shipping with CONFIG_PCIEASPM rather than having this
* issue present. Motivation for adding this new API will be to help
* with power consumption for some of these devices.
*/
pci_disable_link_state(pdev, PCIE_LINK_STATE_L0S);
ret = pci_enable_device(pdev);
if (ret) {
dev_err(&pdev->dev, "can't enable device\n");
......
......@@ -191,6 +191,7 @@
#define AR9287_EEP_NO_BACK_VER AR9287_EEP_MINOR_VER_1
#define AR9287_EEP_START_LOC 128
#define AR9287_HTC_EEP_START_LOC 256
#define AR9287_NUM_2G_CAL_PIERS 3
#define AR9287_NUM_2G_CCK_TARGET_POWERS 3
#define AR9287_NUM_2G_20_TARGET_POWERS 3
......
......@@ -34,9 +34,14 @@ static bool ath9k_hw_ar9287_fill_eeprom(struct ath_hw *ah)
struct ar9287_eeprom *eep = &ah->eeprom.map9287;
struct ath_common *common = ath9k_hw_common(ah);
u16 *eep_data;
int addr, eep_start_loc = AR9287_EEP_START_LOC;
int addr, eep_start_loc;
eep_data = (u16 *)eep;
if (ah->hw_version.devid == 0x7015)
eep_start_loc = AR9287_HTC_EEP_START_LOC;
else
eep_start_loc = AR9287_EEP_START_LOC;
if (!ath9k_hw_use_flash(ah)) {
ath_print(common, ATH_DBG_EEPROM,
"Reading from EEPROM, not flash\n");
......
......@@ -799,7 +799,7 @@ static int ath9k_hif_usb_download_fw(struct hif_device_usb *hif_dev)
}
kfree(buf);
if (hif_dev->device_id == 0x7010)
if ((hif_dev->device_id == 0x7010) || (hif_dev->device_id == 0x7015))
firm_offset = AR7010_FIRMWARE_TEXT;
else
firm_offset = AR9271_FIRMWARE_TEXT;
......@@ -901,6 +901,7 @@ static int ath9k_hif_usb_probe(struct usb_interface *interface,
switch(hif_dev->device_id) {
case 0x7010:
case 0x7015:
case 0x9018:
if (le16_to_cpu(udev->descriptor.bcdDevice) == 0x0202)
hif_dev->fw_name = FIRMWARE_AR7010_1_1;
......@@ -912,11 +913,6 @@ static int ath9k_hif_usb_probe(struct usb_interface *interface,
break;
}
if (!hif_dev->fw_name) {
dev_err(&udev->dev, "Can't determine firmware !\n");
goto err_htc_hw_alloc;
}
ret = ath9k_hif_usb_dev_init(hif_dev);
if (ret) {
ret = -EINVAL;
......
......@@ -245,6 +245,7 @@ static int ath9k_init_htc_services(struct ath9k_htc_priv *priv, u16 devid)
switch(devid) {
case 0x7010:
case 0x7015:
case 0x9018:
priv->htc->credits = 45;
break;
......
......@@ -366,7 +366,8 @@ static void ath9k_htc_setup_rate(struct ath9k_htc_priv *priv,
caps = WLAN_RC_HT_FLAG;
if (sta->ht_cap.mcs.rx_mask[1])
caps |= WLAN_RC_DS_FLAG;
if (sta->ht_cap.cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40)
if ((sta->ht_cap.cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40) &&
(conf_is_ht40(&priv->hw->conf)))
caps |= WLAN_RC_40_FLAG;
if (conf_is_ht40(&priv->hw->conf) &&
(sta->ht_cap.cap & IEEE80211_HT_CAP_SGI_40))
......
......@@ -78,18 +78,23 @@ int ath9k_htc_tx_start(struct ath9k_htc_priv *priv, struct sk_buff *skb)
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
struct ieee80211_sta *sta = tx_info->control.sta;
struct ath9k_htc_sta *ista;
struct ath9k_htc_vif *avp;
struct ath9k_htc_tx_ctl tx_ctl;
enum htc_endpoint_id epid;
u16 qnum;
__le16 fc;
u8 *tx_fhdr;
u8 sta_idx;
u8 sta_idx, vif_idx;
hdr = (struct ieee80211_hdr *) skb->data;
fc = hdr->frame_control;
avp = (struct ath9k_htc_vif *) tx_info->control.vif->drv_priv;
if (tx_info->control.vif &&
(struct ath9k_htc_vif *) tx_info->control.vif->drv_priv)
vif_idx = ((struct ath9k_htc_vif *)
tx_info->control.vif->drv_priv)->index;
else
vif_idx = priv->nvifs;
if (sta) {
ista = (struct ath9k_htc_sta *) sta->drv_priv;
sta_idx = ista->index;
......@@ -106,7 +111,7 @@ int ath9k_htc_tx_start(struct ath9k_htc_priv *priv, struct sk_buff *skb)
memset(&tx_hdr, 0, sizeof(struct tx_frame_hdr));
tx_hdr.node_idx = sta_idx;
tx_hdr.vif_idx = avp->index;
tx_hdr.vif_idx = vif_idx;
if (tx_info->flags & IEEE80211_TX_CTL_AMPDU) {
tx_ctl.type = ATH9K_HTC_AMPDU;
......@@ -169,7 +174,7 @@ int ath9k_htc_tx_start(struct ath9k_htc_priv *priv, struct sk_buff *skb)
tx_ctl.type = ATH9K_HTC_NORMAL;
mgmt_hdr.node_idx = sta_idx;
mgmt_hdr.vif_idx = avp->index;
mgmt_hdr.vif_idx = vif_idx;
mgmt_hdr.tidno = 0;
mgmt_hdr.flags = 0;
......
......@@ -899,6 +899,7 @@
#define AR_DEVID_7010(_ah) \
(((_ah)->hw_version.devid == 0x7010) || \
((_ah)->hw_version.devid == 0x7015) || \
((_ah)->hw_version.devid == 0x9018))
#define AR_RADIO_SREV_MAJOR 0xf0
......
......@@ -6665,12 +6665,13 @@ static int __init ipw2100_init(void)
printk(KERN_INFO DRV_NAME ": %s, %s\n", DRV_DESCRIPTION, DRV_VERSION);
printk(KERN_INFO DRV_NAME ": %s\n", DRV_COPYRIGHT);
pm_qos_add_request(&ipw2100_pm_qos_req, PM_QOS_CPU_DMA_LATENCY,
PM_QOS_DEFAULT_VALUE);
ret = pci_register_driver(&ipw2100_pci_driver);
if (ret)
goto out;
pm_qos_add_request(&ipw2100_pm_qos_req, PM_QOS_CPU_DMA_LATENCY,
PM_QOS_DEFAULT_VALUE);
#ifdef CONFIG_IPW2100_DEBUG
ipw2100_debug_level = debug;
ret = driver_create_file(&ipw2100_pci_driver.driver,
......
......@@ -484,7 +484,7 @@ int wl1251_cmd_trigger_scan_to(struct wl1251 *wl, u32 timeout)
cmd->timeout = timeout;
ret = wl1251_cmd_send(wl, CMD_SCAN, cmd, sizeof(*cmd));
ret = wl1251_cmd_send(wl, CMD_TRIGGER_SCAN_TO, cmd, sizeof(*cmd));
if (ret < 0) {
wl1251_error("cmd trigger scan to failed: %d", ret);
goto out;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册