media: replace bellow -> below

Bellow is yelling. Ok, sometimes the code is yells a lot, but
but this is not the case there ;)
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

drivers/media/common/siano/smsir.c

@@ -78,7 +78,7 @@ int sms_ir_init(struct smscore_device_t *coredev)
 	dev->dev.parent = coredev->device;
 
 #if 0
-	/* TODO: properly initialize the parameters bellow */
+	/* TODO: properly initialize the parameters below */
 	dev->input_id.bustype = BUS_USB;
 	dev->input_id.version = 1;
 	dev->input_id.vendor = le16_to_cpu(dev->udev->descriptor.idVendor);

drivers/media/dvb-frontends/drx39xyj/drxj.c

@@ -9541,7 +9541,7 @@ ctrl_get_qam_sig_quality(struct drx_demod_instance *demod)
 	/* ----------------------------------------- */
 	/* Pre Viterbi Symbol Error Rate Calculation */
 	/* ----------------------------------------- */
-	/* pre viterbi SER is good if it is bellow 0.025 */
+	/* pre viterbi SER is good if it is below 0.025 */
 
 	/* get the register value */
 	/*   no of quadrature symbol errors */

drivers/media/dvb-frontends/drxk_hard.c

@@ -544,7 +544,7 @@ static int power_up_device(struct drxk_state *state)
 static int init_state(struct drxk_state *state)
 {
 	/*
-	 * FIXME: most (all?) of the values bellow should be moved into
+	 * FIXME: most (all?) of the values below should be moved into
 	 * struct drxk_config, as they are probably board-specific
 	 */
 	u32 ul_vsb_if_agc_mode = DRXK_AGC_CTRL_AUTO;

drivers/media/dvb-frontends/tda10021.c

@@ -258,7 +258,7 @@ static int tda10021_set_parameters(struct dvb_frontend *fe)
 	}
 
 	/*
-	 * gcc optimizes the code bellow the same way as it would code:
+	 * gcc optimizes the code below the same way as it would code:
 	 *           "if (qam > 5) return -EINVAL;"
 	 * Yet, the code is clearer, as it shows what QAM standards are
 	 * supported by the driver, and avoids the usage of magic numbers on

drivers/media/dvb-frontends/tda10023.c

@@ -331,7 +331,7 @@ static int tda10023_set_parameters(struct dvb_frontend *fe)
 	}
 
 	/*
-	 * gcc optimizes the code bellow the same way as it would code:
+	 * gcc optimizes the code below the same way as it would code:
 	 *		 "if (qam > 5) return -EINVAL;"
 	 * Yet, the code is clearer, as it shows what QAM standards are
 	 * supported by the driver, and avoids the usage of magic numbers on

drivers/media/i2c/tvaudio.c

@@ -272,7 +272,7 @@ static int chip_cmd(struct CHIPSTATE *chip, char *name, audiocmd *cmd)
 		return -EINVAL;
 	}
 
-	/* FIXME: it seems that the shadow bytes are wrong bellow !*/
+	/* FIXME: it seems that the shadow bytes are wrong below !*/
 
 	/* update our shadow register set; print bytes if (debug > 0) */
 	v4l2_dbg(1, debug, sd, "chip_cmd(%s): reg=%d, data:",

drivers/media/tuners/tuner-xc2028.c

@@ -1094,7 +1094,7 @@ static int generic_set_freq(struct dvb_frontend *fe, u32 freq /* in HZ */,
 		 * Still need tests for XC3028L (firmware 3.2 or upper)
 		 * So, for now, let's just comment the per-firmware
 		 * version of this change. Reports with xc3028l working
-		 * with and without the lines bellow are welcome
+		 * with and without the lines below are welcome
 		 */
 
 		if (priv->firm_version < 0x0302) {