fsl/usb: Add controller version based ULPI and UTMI phy support

Add support for ULPI and UTMI PHYs based on usb controller
version info read from device-tree

Example of USB Controller versioning info:
Version 1.2 and below : MPC8536, MPC8315, etc
Version 1.6 : P1020, P1010, P2020, P5020, etc
Version 2.2 : PSC9131, PSC9132, P3060, etc

No changes for non-DT users
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/gadget/fsl_udc_core.c

 /*
- * Copyright (C) 2004-2007,2011 Freescale Semiconductor, Inc.
+ * Copyright (C) 2004-2007,2011-2012 Freescale Semiconductor, Inc.
  * All rights reserved.
  *
  * Author: Li Yang <leoli@freescale.com>
@@ -58,9 +58,8 @@ static const char driver_name[] = "fsl-usb2-udc";
 static const char driver_desc[] = DRIVER_DESC;
 
 static struct usb_dr_device *dr_regs;
-#ifndef CONFIG_ARCH_MXC
+
 static struct usb_sys_interface *usb_sys_regs;
-#endif
 
 /* it is initialized in probe()  */
 static struct fsl_udc *udc_controller = NULL;
@@ -244,10 +243,9 @@ static int dr_controller_setup(struct fsl_udc *udc)
 {
 	unsigned int tmp, portctrl, ep_num;
 	unsigned int max_no_of_ep;
-#ifndef CONFIG_ARCH_MXC
 	unsigned int ctrl;
-#endif
 	unsigned long timeout;
+
 #define FSL_UDC_RESET_TIMEOUT 1000
 
 	/* Config PHY interface */
@@ -255,12 +253,32 @@ static int dr_controller_setup(struct fsl_udc *udc)
 	portctrl &= ~(PORTSCX_PHY_TYPE_SEL | PORTSCX_PORT_WIDTH);
 	switch (udc->phy_mode) {
 	case FSL_USB2_PHY_ULPI:
+		if (udc->pdata->have_sysif_regs) {
+			if (udc->pdata->controller_ver) {
+				/* controller version 1.6 or above */
+				ctrl = __raw_readl(&usb_sys_regs->control);
+				ctrl &= ~USB_CTRL_UTMI_PHY_EN;
+				ctrl |= USB_CTRL_USB_EN;
+				__raw_writel(ctrl, &usb_sys_regs->control);
+			}
+		}
 		portctrl |= PORTSCX_PTS_ULPI;
 		break;
 	case FSL_USB2_PHY_UTMI_WIDE:
 		portctrl |= PORTSCX_PTW_16BIT;
 		/* fall through */
 	case FSL_USB2_PHY_UTMI:
+		if (udc->pdata->have_sysif_regs) {
+			if (udc->pdata->controller_ver) {
+				/* controller version 1.6 or above */
+				ctrl = __raw_readl(&usb_sys_regs->control);
+				ctrl |= (USB_CTRL_UTMI_PHY_EN |
+					USB_CTRL_USB_EN);
+				__raw_writel(ctrl, &usb_sys_regs->control);
+				mdelay(FSL_UTMI_PHY_DLY); /* Delay for UTMI
+					PHY CLK to become stable - 10ms*/
+			}
+		}
 		portctrl |= PORTSCX_PTS_UTMI;
 		break;
 	case FSL_USB2_PHY_SERIAL:

drivers/usb/gadget/fsl_usb2_udc.h

 /*
+ * Copyright (C) 2004,2012 Freescale Semiconductor, Inc
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
  * Freescale USB device/endpoint management registers
  */
 #ifndef __FSL_USB2_UDC_H
@@ -348,6 +356,9 @@ struct usb_sys_interface {
 /* control Register Bit Masks */
 #define  USB_CTRL_IOENB                       0x00000004
 #define  USB_CTRL_ULPI_INT0EN                 0x00000001
+#define USB_CTRL_UTMI_PHY_EN		      0x00000200
+#define USB_CTRL_USB_EN			      0x00000004
+#define USB_CTRL_ULPI_PHY_CLK_SEL	      0x00000400
 
 /* Endpoint Queue Head data struct
  * Rem: all the variables of qh are LittleEndian Mode

drivers/usb/host/ehci-fsl.c

 /*
  * Copyright 2005-2009 MontaVista Software, Inc.
- * Copyright 2008      Freescale Semiconductor, Inc.
+ * Copyright 2008,2012      Freescale Semiconductor, Inc.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
@@ -211,19 +211,32 @@ static void usb_hcd_fsl_remove(struct usb_hcd *hcd,
 	usb_put_hcd(hcd);
 }
 
-static void ehci_fsl_setup_phy(struct ehci_hcd *ehci,
+static void ehci_fsl_setup_phy(struct usb_hcd *hcd,
 			       enum fsl_usb2_phy_modes phy_mode,
 			       unsigned int port_offset)
 {
-	u32 portsc;
-	struct usb_hcd *hcd = ehci_to_hcd(ehci);
+	u32 portsc, temp;
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
 	void __iomem *non_ehci = hcd->regs;
+	struct device *dev = hcd->self.controller;
+	struct fsl_usb2_platform_data *pdata = dev->platform_data;
+
+	if (pdata->controller_ver < 0) {
+		dev_warn(hcd->self.controller, "Could not get controller version\n");
+		return;
+	}
 
 	portsc = ehci_readl(ehci, &ehci->regs->port_status[port_offset]);
 	portsc &= ~(PORT_PTS_MSK | PORT_PTS_PTW);
 
 	switch (phy_mode) {
 	case FSL_USB2_PHY_ULPI:
+		if (pdata->controller_ver) {
+			/* controller version 1.6 or above */
+			temp = in_be32(non_ehci + FSL_SOC_USB_CTRL);
+			out_be32(non_ehci + FSL_SOC_USB_CTRL, temp |
+				USB_CTRL_USB_EN | ULPI_PHY_CLK_SEL);
+		}
 		portsc |= PORT_PTS_ULPI;
 		break;
 	case FSL_USB2_PHY_SERIAL:
@@ -233,6 +246,14 @@ static void ehci_fsl_setup_phy(struct ehci_hcd *ehci,
 		portsc |= PORT_PTS_PTW;
 		/* fall through */
 	case FSL_USB2_PHY_UTMI:
+		if (pdata->controller_ver) {
+			/* controller version 1.6 or above */
+			temp = in_be32(non_ehci + FSL_SOC_USB_CTRL);
+			out_be32(non_ehci + FSL_SOC_USB_CTRL, temp |
+				UTMI_PHY_EN | USB_CTRL_USB_EN);
+			mdelay(FSL_UTMI_PHY_DLY);  /* Delay for UTMI PHY CLK to
+						become stable - 10ms*/
+		}
 		/* enable UTMI PHY */
 		setbits32(non_ehci + FSL_SOC_USB_CTRL, CTRL_UTMI_PHY_EN);
 		portsc |= PORT_PTS_UTMI;
@@ -271,7 +292,7 @@ static void ehci_fsl_usb_setup(struct ehci_hcd *ehci)
 
 	if ((pdata->operating_mode == FSL_USB2_DR_HOST) ||
 			(pdata->operating_mode == FSL_USB2_DR_OTG))
-		ehci_fsl_setup_phy(ehci, pdata->phy_mode, 0);
+		ehci_fsl_setup_phy(hcd, pdata->phy_mode, 0);
 
 	if (pdata->operating_mode == FSL_USB2_MPH_HOST) {
 		unsigned int chip, rev, svr;
@@ -285,9 +306,9 @@ static void ehci_fsl_usb_setup(struct ehci_hcd *ehci)
 			ehci->has_fsl_port_bug = 1;
 
 		if (pdata->port_enables & FSL_USB2_PORT0_ENABLED)
-			ehci_fsl_setup_phy(ehci, pdata->phy_mode, 0);
+			ehci_fsl_setup_phy(hcd, pdata->phy_mode, 0);
 		if (pdata->port_enables & FSL_USB2_PORT1_ENABLED)
-			ehci_fsl_setup_phy(ehci, pdata->phy_mode, 1);
+			ehci_fsl_setup_phy(hcd, pdata->phy_mode, 1);
 	}
 
 	if (pdata->have_sysif_regs) {

drivers/usb/host/ehci-fsl.h

-/* Copyright (C) 2005-2010 Freescale Semiconductor, Inc.
+/* Copyright (C) 2005-2010,2012 Freescale Semiconductor, Inc.
  * Copyright (c) 2005 MontaVista Software
  *
  * This program is free software; you can redistribute  it and/or modify it
@@ -50,4 +50,15 @@
 #define CTRL_UTMI_PHY_EN	(1<<9)
 #define CTRL_PHY_CLK_VALID	(1 << 17)
 #define SNOOP_SIZE_2GB		0x1e
+
+/* control Register Bit Masks */
+#define ULPI_INT_EN             (1<<0)
+#define WU_INT_EN               (1<<1)
+#define USB_CTRL_USB_EN         (1<<2)
+#define LINE_STATE_FILTER__EN   (1<<3)
+#define KEEP_OTG_ON             (1<<4)
+#define OTG_PORT                (1<<5)
+#define PLL_RESET               (1<<8)
+#define UTMI_PHY_EN             (1<<9)
+#define ULPI_PHY_CLK_SEL        (1<<10)
 #endif				/* _EHCI_FSL_H */

drivers/usb/host/fsl-mph-dr-of.c

@@ -119,6 +119,39 @@ struct platform_device * __devinit fsl_usb2_device_register(
 
 static const struct of_device_id fsl_usb2_mph_dr_of_match[];
 
+static int usb_get_ver_info(struct device_node *np)
+{
+	int ver = -1;
+
+	/*
+	 * returns 1 for usb controller version 1.6
+	 * returns 2 for usb controller version 2.2
+	 * returns 0 otherwise
+	 */
+	if (of_device_is_compatible(np, "fsl-usb2-dr")) {
+		if (of_device_is_compatible(np, "fsl-usb2-dr-v1.6"))
+			ver = FSL_USB_VER_1_6;
+		else if (of_device_is_compatible(np, "fsl-usb2-dr-v2.2"))
+			ver = FSL_USB_VER_2_2;
+		else /* for previous controller versions */
+			ver = FSL_USB_VER_OLD;
+
+		if (ver > -1)
+			return ver;
+	}
+
+	if (of_device_is_compatible(np, "fsl-usb2-mph")) {
+		if (of_device_is_compatible(np, "fsl-usb2-mph-v1.6"))
+			ver = FSL_USB_VER_1_6;
+		else if (of_device_is_compatible(np, "fsl-usb2-mph-v2.2"))
+			ver = FSL_USB_VER_2_2;
+		else /* for previous controller versions */
+			ver = FSL_USB_VER_OLD;
+	}
+
+	return ver;
+}
+
 static int __devinit fsl_usb2_mph_dr_of_probe(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
@@ -166,6 +199,14 @@ static int __devinit fsl_usb2_mph_dr_of_probe(struct platform_device *ofdev)
 
 	prop = of_get_property(np, "phy_type", NULL);
 	pdata->phy_mode = determine_usb_phy(prop);
+	pdata->controller_ver = usb_get_ver_info(np);
+
+	if (pdata->have_sysif_regs) {
+		if (pdata->controller_ver < 0) {
+			dev_warn(&ofdev->dev, "Could not get controller version\n");
+			return -ENODEV;
+		}
+	}
 
 	for (i = 0; i < ARRAY_SIZE(dev_data->drivers); i++) {
 		if (!dev_data->drivers[i])

include/linux/fsl_devices.h

@@ -6,7 +6,7 @@
  *
  * Maintainer: Kumar Gala <galak@kernel.crashing.org>
  *
- * Copyright 2004 Freescale Semiconductor, Inc
+ * Copyright 2004,2012 Freescale Semiconductor, Inc
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
@@ -17,6 +17,12 @@
 #ifndef _FSL_DEVICE_H_
 #define _FSL_DEVICE_H_
 
+#define FSL_UTMI_PHY_DLY	10	/*As per P1010RM, delay for UTMI
+				PHY CLK to become stable - 10ms*/
+#define FSL_USB_VER_OLD		0
+#define FSL_USB_VER_1_6		1
+#define FSL_USB_VER_2_2		2
+
 #include <linux/types.h>
 
 /*
@@ -63,6 +69,7 @@ struct platform_device;
 
 struct fsl_usb2_platform_data {
 	/* board specific information */
+	int				controller_ver;
 	enum fsl_usb2_operating_modes	operating_mode;
 	enum fsl_usb2_phy_modes		phy_mode;
 	unsigned int			port_enables;