提交 571e7b85 编写于 作者: D David S. Miller

Merge branch 'sh_eth-R8A77980-GEther-support'

Sergei Shtylyov says:

====================
Add Renesas R8A77980 GEther support

Here's a set of 3 patches against DaveM's 'net-next.git' repo. They (gradually)
add R8A77980 GEther support to the 'sh_eth' driver, starting with couple new
register bits/values introduced with this chip, and ending with adding a new
'struct sh_eth_cpu_data' instance connected to the new DT "compatible" prop
value...
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
......@@ -14,6 +14,7 @@ Required properties:
"renesas,ether-r8a7791" if the device is a part of R8A7791 SoC.
"renesas,ether-r8a7793" if the device is a part of R8A7793 SoC.
"renesas,ether-r8a7794" if the device is a part of R8A7794 SoC.
"renesas,gether-r8a77980" if the device is a part of R8A77980 SoC.
"renesas,ether-r7s72100" if the device is a part of R7S72100 SoC.
"renesas,rcar-gen1-ether" for a generic R-Car Gen1 device.
"renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1
......
......@@ -466,6 +466,9 @@ static void sh_eth_select_mii(struct net_device *ndev)
u32 value;
switch (mdp->phy_interface) {
case PHY_INTERFACE_MODE_RGMII ... PHY_INTERFACE_MODE_RGMII_TXID:
value = 0x3;
break;
case PHY_INTERFACE_MODE_GMII:
value = 0x2;
break;
......@@ -750,6 +753,49 @@ static struct sh_eth_cpu_data rcar_gen2_data = {
.rmiimode = 1,
.magic = 1,
};
/* R8A77980 */
static struct sh_eth_cpu_data r8a77980_data = {
.soft_reset = sh_eth_soft_reset_gether,
.set_duplex = sh_eth_set_duplex,
.set_rate = sh_eth_set_rate_gether,
.register_type = SH_ETH_REG_GIGABIT,
.edtrr_trns = EDTRR_TRNS_GETHER,
.ecsr_value = ECSR_PSRTO | ECSR_LCHNG | ECSR_ICD | ECSR_MPD,
.ecsipr_value = ECSIPR_PSRTOIP | ECSIPR_LCHNGIP | ECSIPR_ICDIP |
ECSIPR_MPDIP,
.eesipr_value = EESIPR_RFCOFIP | EESIPR_ECIIP |
EESIPR_FTCIP | EESIPR_TDEIP | EESIPR_TFUFIP |
EESIPR_FRIP | EESIPR_RDEIP | EESIPR_RFOFIP |
EESIPR_RMAFIP | EESIPR_RRFIP |
EESIPR_RTLFIP | EESIPR_RTSFIP |
EESIPR_PREIP | EESIPR_CERFIP,
.tx_check = EESR_FTC | EESR_CD | EESR_RTO,
.eesr_err_check = EESR_TWB1 | EESR_TWB | EESR_TABT | EESR_RABT |
EESR_RFE | EESR_RDE | EESR_RFRMER |
EESR_TFE | EESR_TDE | EESR_ECI,
.fdr_value = 0x0000070f,
.apr = 1,
.mpr = 1,
.tpauser = 1,
.bculr = 1,
.hw_swap = 1,
.nbst = 1,
.rpadir = 1,
.rpadir_value = 2 << 16,
.no_trimd = 1,
.no_ade = 1,
.xdfar_rw = 1,
.hw_checksum = 1,
.select_mii = 1,
.magic = 1,
.cexcr = 1,
};
#endif /* CONFIG_OF */
static void sh_eth_set_rate_sh7724(struct net_device *ndev)
......@@ -1431,6 +1477,10 @@ static int sh_eth_dev_init(struct net_device *ndev)
sh_eth_write(ndev, mdp->cd->trscer_err_mask, TRSCER);
/* DMA transfer burst mode */
if (mdp->cd->nbst)
sh_eth_modify(ndev, EDMR, EDMR_NBST, EDMR_NBST);
if (mdp->cd->bculr)
sh_eth_write(ndev, 0x800, BCULR); /* Burst sycle set */
......@@ -3127,6 +3177,7 @@ static const struct of_device_id sh_eth_match_table[] = {
{ .compatible = "renesas,ether-r8a7791", .data = &rcar_gen2_data },
{ .compatible = "renesas,ether-r8a7793", .data = &rcar_gen2_data },
{ .compatible = "renesas,ether-r8a7794", .data = &rcar_gen2_data },
{ .compatible = "renesas,gether-r8a77980", .data = &r8a77980_data },
{ .compatible = "renesas,ether-r7s72100", .data = &r7s72100_data },
{ .compatible = "renesas,rcar-gen1-ether", .data = &rcar_gen1_data },
{ .compatible = "renesas,rcar-gen2-ether", .data = &rcar_gen2_data },
......
......@@ -184,6 +184,7 @@ enum GECMR_BIT {
/* EDMR */
enum DMAC_M_BIT {
EDMR_NBST = 0x80,
EDMR_EL = 0x40, /* Litte endian */
EDMR_DL1 = 0x20, EDMR_DL0 = 0x10,
EDMR_SRST_GETHER = 0x03,
......@@ -505,6 +506,7 @@ struct sh_eth_cpu_data {
unsigned bculr:1; /* EtherC have BCULR */
unsigned tsu:1; /* EtherC have TSU */
unsigned hw_swap:1; /* E-DMAC have DE bit in EDMR */
unsigned nbst:1; /* E-DMAC has NBST bit in EDMR */
unsigned rpadir:1; /* E-DMAC have RPADIR */
unsigned no_trimd:1; /* E-DMAC DO NOT have TRIMD */
unsigned no_ade:1; /* E-DMAC DO NOT have ADE bit in EESR */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册