提交 56a5cbaf 编写于 作者: B Ben Dooks

ARM: s3c6400_defconfig: Add SPI driver

The SPI driver was added last kernel round, so enable
the core SPI and add the 64XX and bitbang driver as
modules.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
上级 e56210ca
......@@ -481,6 +481,9 @@ CONFIG_MTD_CFI_I2=y
#
# Self-contained MTD device drivers
#
# CONFIG_MTD_DATAFLASH is not set
# CONFIG_MTD_M25P80 is not set
# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
......@@ -540,12 +543,14 @@ CONFIG_MISC_DEVICES=y
# CONFIG_ISL29003 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_DS1682 is not set
# CONFIG_TI_DAC7512 is not set
# CONFIG_C2PORT is not set
#
# EEPROM support
#
CONFIG_EEPROM_AT24=y
# CONFIG_EEPROM_AT25 is not set
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
......@@ -660,6 +665,7 @@ CONFIG_SERIAL_SAMSUNG_UARTS=4
# CONFIG_SERIAL_SAMSUNG_DEBUG is not set
CONFIG_SERIAL_SAMSUNG_CONSOLE=y
CONFIG_SERIAL_S3C6400=y
# CONFIG_SERIAL_MAX3100 is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_TIMBERDALE is not set
......@@ -709,7 +715,24 @@ CONFIG_I2C_S3C2410=y
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_SPI is not set
CONFIG_SPI=y
# CONFIG_SPI_DEBUG is not set
CONFIG_SPI_MASTER=y
#
# SPI Master Controller Drivers
#
CONFIG_SPI_BITBANG=m
CONFIG_SPI_GPIO=m
CONFIG_SPI_S3C64XX=m
# CONFIG_SPI_XILINX is not set
# CONFIG_SPI_DESIGNWARE is not set
#
# SPI Protocol Masters
#
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
#
# PPS support
......@@ -741,6 +764,9 @@ CONFIG_GPIOLIB=y
#
# SPI GPIO expanders:
#
# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
# CONFIG_GPIO_MC33880 is not set
#
# AC97 GPIO expanders:
......@@ -756,6 +782,7 @@ CONFIG_HWMON=y
#
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADCXX is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
......@@ -777,6 +804,7 @@ CONFIG_HWMON=y
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM70 is not set
# CONFIG_SENSORS_LM73 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
......@@ -791,6 +819,7 @@ CONFIG_HWMON=y
# CONFIG_SENSORS_LTC4215 is not set
# CONFIG_SENSORS_LTC4245 is not set
# CONFIG_SENSORS_LM95241 is not set
# CONFIG_SENSORS_MAX1111 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
......@@ -802,6 +831,7 @@ CONFIG_HWMON=y
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_ADS7871 is not set
# CONFIG_SENSORS_AMC6821 is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_TMP401 is not set
......@@ -815,6 +845,7 @@ CONFIG_HWMON=y
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_LIS3_SPI is not set
# CONFIG_SENSORS_LIS3_I2C is not set
# CONFIG_THERMAL is not set
# CONFIG_WATCHDOG is not set
......@@ -851,7 +882,10 @@ CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_WM8994 is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_MFD_MC13783 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_EZX_PCAP is not set
# CONFIG_AB4500_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
......@@ -901,6 +935,7 @@ CONFIG_SND_DRIVERS=y
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
CONFIG_SND_ARM=y
CONFIG_SND_SPI=y
CONFIG_SND_SOC=m
CONFIG_SND_SOC_AC97_BUS=y
CONFIG_SND_S3C24XX_SOC=m
......@@ -957,6 +992,7 @@ CONFIG_MMC_SDHCI=y
# CONFIG_MMC_SDHCI_PLTFM is not set
CONFIG_MMC_SDHCI_S3C=y
# CONFIG_MMC_SDHCI_S3C_DMA is not set
# CONFIG_MMC_SPI is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册