提交 554f4ffd 编写于 作者: J Jeff Kirsher

hamachi/yellowfin: Move the packet engine drivers

Move the packet engine drivers to drivers/net/ethernet/packetengines/
and the necessary Kconfig and Makefile changes.

CC: Donald Becker <becker@scyld.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
上级 b544dbac
......@@ -541,32 +541,6 @@ config IP1000
To compile this driver as a module, choose M here: the module
will be called ipg. This is recommended.
config HAMACHI
tristate "Packet Engines Hamachi GNIC-II support"
depends on PCI
select MII
help
If you have a Gigabit Ethernet card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module will be
called hamachi.
config YELLOWFIN
tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
depends on PCI && EXPERIMENTAL
select CRC32
---help---
Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
used by the Beowulf Linux cluster project. See
<http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
information about this driver in particular and Beowulf in general.
To compile this driver as a module, choose M here: the module
will be called yellowfin. This is recommended.
config XILINX_LL_TEMAC
tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
depends on PPC || MICROBLAZE
......
......@@ -19,7 +19,6 @@ obj-$(CONFIG_PLIP) += plip.o
obj-$(CONFIG_ROADRUNNER) += rrunner.o
obj-$(CONFIG_R6040) += r6040.o
obj-$(CONFIG_YELLOWFIN) += yellowfin.o
obj-$(CONFIG_FEALNX) += fealnx.o
obj-$(CONFIG_SKFP) += skfp/
obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
......@@ -30,7 +29,6 @@ obj-$(CONFIG_SH_ETH) += sh_eth.o
# end link order section
#
obj-$(CONFIG_HAMACHI) += hamachi.o
obj-$(CONFIG_NET) += Space.o loopback.o
obj-$(CONFIG_NET_SB1000) += sb1000.o
obj-$(CONFIG_HP100) += hp100.o
......
......@@ -39,6 +39,7 @@ source "drivers/net/ethernet/natsemi/Kconfig"
source "drivers/net/ethernet/8390/Kconfig"
source "drivers/net/ethernet/nuvoton/Kconfig"
source "drivers/net/ethernet/oki-semi/Kconfig"
source "drivers/net/ethernet/packetengines/Kconfig"
source "drivers/net/ethernet/pasemi/Kconfig"
source "drivers/net/ethernet/qlogic/Kconfig"
source "drivers/net/ethernet/racal/Kconfig"
......
......@@ -30,6 +30,7 @@ obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
obj-$(CONFIG_NET_VENDOR_NATSEMI) += natsemi/
obj-$(CONFIG_NET_VENDOR_NUVOTON) += nuvoton/
obj-$(CONFIG_NET_VENDOR_OKI) += oki-semi/
obj-$(CONFIG_NET_PACKET_ENGINE) += packetengines/
obj-$(CONFIG_NET_VENDOR_PASEMI) += pasemi/
obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
......
#
# Packet engine device configuration
#
config NET_PACKET_ENGINE
bool "Packet Engine devices"
depends on PCI
---help---
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about packet engine devices. If you say Y, you will
be asked for your specific card in the following questions.
if NET_PACKET_ENGINE
config HAMACHI
tristate "Packet Engines Hamachi GNIC-II support"
depends on PCI
select MII
---help---
If you have a Gigabit Ethernet card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module will be
called hamachi.
config YELLOWFIN
tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
depends on PCI && EXPERIMENTAL
select CRC32
---help---
Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
used by the Beowulf Linux cluster project. See
<http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
information about this driver in particular and Beowulf in general.
To compile this driver as a module, choose M here: the module
will be called yellowfin. This is recommended.
endif # NET_PACKET_ENGINE
#
# Makefile for the Packet Engine network device drivers.
#
obj-$(CONFIG_HAMACHI) += hamachi.o
obj-$(CONFIG_YELLOWFIN) += yellowfin.o
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册