提交 52c4d6c4 编写于 作者: Y Yaniv Rosner 提交者: David S. Miller

bnx2x: Change BCM54616S to BCM54618SE

Change 1G copper PHY BCM54616S to BCM54618SE since we only have HW with latter one of the two.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 b8d6d082
......@@ -696,7 +696,7 @@ struct port_hw_cfg { /* port 0: 0x12c port 1: 0x2bc */
#define PORT_HW_CFG_XGXS_EXT_PHY2_TYPE_BCM84823 0x00000b00
#define PORT_HW_CFG_XGXS_EXT_PHY2_TYPE_BCM54640 0x00000c00
#define PORT_HW_CFG_XGXS_EXT_PHY2_TYPE_BCM84833 0x00000d00
#define PORT_HW_CFG_XGXS_EXT_PHY2_TYPE_BCM54616 0x00000e00
#define PORT_HW_CFG_XGXS_EXT_PHY2_TYPE_BCM54618SE 0x00000e00
#define PORT_HW_CFG_XGXS_EXT_PHY2_TYPE_BCM8722 0x00000f00
#define PORT_HW_CFG_XGXS_EXT_PHY2_TYPE_FAILURE 0x0000fd00
#define PORT_HW_CFG_XGXS_EXT_PHY2_TYPE_NOT_CONN 0x0000ff00
......@@ -751,7 +751,7 @@ struct port_hw_cfg { /* port 0: 0x12c port 1: 0x2bc */
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823 0x00000b00
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54640 0x00000c00
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833 0x00000d00
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54616 0x00000e00
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE 0x00000e00
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722 0x00000f00
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT_WC 0x0000fc00
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE 0x0000fd00
......
......@@ -3530,7 +3530,7 @@ static u8 bnx2x_ext_phy_resolve_fc(struct bnx2x_phy *phy,
vars->flow_ctrl = params->req_fc_auto_adv;
else if (vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) {
ret = 1;
if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54616) {
if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE) {
bnx2x_cl22_read(bp, phy,
0x4, &ld_pause);
bnx2x_cl22_read(bp, phy,
......@@ -5549,7 +5549,7 @@ static u16 bnx2x_wait_reset_complete(struct bnx2x *bp,
u16 cnt, ctrl;
/* Wait for soft reset to get cleared up to 1 sec */
for (cnt = 0; cnt < 1000; cnt++) {
if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54616)
if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE)
bnx2x_cl22_read(bp, phy,
MDIO_PMA_REG_CTRL, &ctrl);
else
......@@ -9800,9 +9800,9 @@ static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy,
}
/******************************************************************/
/* 54616S PHY SECTION */
/* 54618SE PHY SECTION */
/******************************************************************/
static int bnx2x_54616s_config_init(struct bnx2x_phy *phy,
static int bnx2x_54618se_config_init(struct bnx2x_phy *phy,
struct link_params *params,
struct link_vars *vars)
{
......@@ -9811,7 +9811,7 @@ static int bnx2x_54616s_config_init(struct bnx2x_phy *phy,
u16 autoneg_val, an_1000_val, an_10_100_val, fc_val, temp;
u32 cfg_pin;
DP(NETIF_MSG_LINK, "54616S cfg init\n");
DP(NETIF_MSG_LINK, "54618SE cfg init\n");
usleep_range(1000, 1000);
/* This works with E3 only, no need to check the chip
......@@ -9973,11 +9973,11 @@ static int bnx2x_54616s_config_init(struct bnx2x_phy *phy,
return 0;
}
static void bnx2x_54616s_set_link_led(struct bnx2x_phy *phy,
struct link_params *params, u8 mode)
static void bnx2x_54618se_set_link_led(struct bnx2x_phy *phy,
struct link_params *params, u8 mode)
{
struct bnx2x *bp = params->bp;
DP(NETIF_MSG_LINK, "54616S set link led (mode=%x)\n", mode);
DP(NETIF_MSG_LINK, "54618SE set link led (mode=%x)\n", mode);
switch (mode) {
case LED_MODE_FRONT_PANEL_OFF:
case LED_MODE_OFF:
......@@ -9989,8 +9989,8 @@ static void bnx2x_54616s_set_link_led(struct bnx2x_phy *phy,
return;
}
static void bnx2x_54616s_link_reset(struct bnx2x_phy *phy,
struct link_params *params)
static void bnx2x_54618se_link_reset(struct bnx2x_phy *phy,
struct link_params *params)
{
struct bnx2x *bp = params->bp;
u32 cfg_pin;
......@@ -10009,9 +10009,9 @@ static void bnx2x_54616s_link_reset(struct bnx2x_phy *phy,
bnx2x_set_cfg_pin(bp, cfg_pin, 0);
}
static u8 bnx2x_54616s_read_status(struct bnx2x_phy *phy,
struct link_params *params,
struct link_vars *vars)
static u8 bnx2x_54618se_read_status(struct bnx2x_phy *phy,
struct link_params *params,
struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u16 val;
......@@ -10022,7 +10022,7 @@ static u8 bnx2x_54616s_read_status(struct bnx2x_phy *phy,
bnx2x_cl22_read(bp, phy,
0x19,
&legacy_status);
DP(NETIF_MSG_LINK, "54616S read_status: 0x%x\n", legacy_status);
DP(NETIF_MSG_LINK, "54618SE read_status: 0x%x\n", legacy_status);
/* Read status to clear the PHY interrupt. */
bnx2x_cl22_read(bp, phy,
......@@ -10074,21 +10074,45 @@ static u8 bnx2x_54616s_read_status(struct bnx2x_phy *phy,
vars->link_status |=
LINK_STATUS_PARALLEL_DETECTION_USED;
DP(NETIF_MSG_LINK, "BCM54616S: link speed is %d\n",
DP(NETIF_MSG_LINK, "BCM54618SE: link speed is %d\n",
vars->line_speed);
/* Report whether EEE is resolved. */
bnx2x_cl22_read(bp, phy, MDIO_REG_GPHY_PHYID_LSB, &val);
if (val == MDIO_REG_GPHY_ID_54618SE) {
if (vars->link_status &
LINK_STATUS_AUTO_NEGOTIATE_COMPLETE)
val = 0;
else {
bnx2x_cl22_write(bp, phy,
MDIO_REG_GPHY_CL45_ADDR_REG,
MDIO_AN_DEVAD);
bnx2x_cl22_write(bp, phy,
MDIO_REG_GPHY_CL45_DATA_REG,
MDIO_REG_GPHY_EEE_RESOLVED);
bnx2x_cl22_write(bp, phy,
MDIO_REG_GPHY_CL45_ADDR_REG,
(0x1 << 14) | MDIO_AN_DEVAD);
bnx2x_cl22_read(bp, phy,
MDIO_REG_GPHY_CL45_DATA_REG,
&val);
}
DP(NETIF_MSG_LINK, "EEE resolution: 0x%x\n", val);
}
bnx2x_ext_phy_resolve_fc(phy, params, vars);
}
return link_up;
}
static void bnx2x_54616s_config_loopback(struct bnx2x_phy *phy,
struct link_params *params)
static void bnx2x_54618se_config_loopback(struct bnx2x_phy *phy,
struct link_params *params)
{
struct bnx2x *bp = params->bp;
u16 val;
u32 umac_base = params->port ? GRCBASE_UMAC1 : GRCBASE_UMAC0;
DP(NETIF_MSG_LINK, "2PMA/PMD ext_phy_loopback: 54616s\n");
DP(NETIF_MSG_LINK, "2PMA/PMD ext_phy_loopback: 54618se\n");
/* Enable master/slave manual mmode and set to master */
/* mii write 9 [bits set 11 12] */
......@@ -10705,8 +10729,8 @@ static struct bnx2x_phy phy_84833 = {
.phy_specific_func = (phy_specific_func_t)NULL
};
static struct bnx2x_phy phy_54616s = {
.type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54616,
static struct bnx2x_phy phy_54618se = {
.type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE,
.addr = 0xff,
.def_md_devad = 0,
.flags = FLAGS_INIT_XGXS_FIRST,
......@@ -10729,13 +10753,13 @@ static struct bnx2x_phy phy_54616s = {
.speed_cap_mask = 0,
/* req_duplex = */0,
/* rsrv = */0,
.config_init = (config_init_t)bnx2x_54616s_config_init,
.read_status = (read_status_t)bnx2x_54616s_read_status,
.link_reset = (link_reset_t)bnx2x_54616s_link_reset,
.config_loopback = (config_loopback_t)bnx2x_54616s_config_loopback,
.config_init = (config_init_t)bnx2x_54618se_config_init,
.read_status = (read_status_t)bnx2x_54618se_read_status,
.link_reset = (link_reset_t)bnx2x_54618se_link_reset,
.config_loopback = (config_loopback_t)bnx2x_54618se_config_loopback,
.format_fw_ver = (format_fw_ver_t)NULL,
.hw_reset = (hw_reset_t)NULL,
.set_link_led = (set_link_led_t)bnx2x_54616s_set_link_led,
.set_link_led = (set_link_led_t)bnx2x_54618se_set_link_led,
.phy_specific_func = (phy_specific_func_t)NULL
};
/*****************************************************************/
......@@ -10978,8 +11002,8 @@ static int bnx2x_populate_ext_phy(struct bnx2x *bp,
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833:
*phy = phy_84833;
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54616:
*phy = phy_54616s;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE:
*phy = phy_54618se;
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
*phy = phy_7101;
......
......@@ -6919,7 +6919,15 @@ Theotherbitsarereservedandshouldbezero*/
#define DIGITAL5_ACTUAL_SPEED_TX_MASK 0x003f
/* 54616s */
/* 54618se */
#define MDIO_REG_GPHY_PHYID_LSB 0x3
#define MDIO_REG_GPHY_ID_54618SE 0x5cd5
#define MDIO_REG_GPHY_CL45_ADDR_REG 0xd
#define MDIO_REG_GPHY_CL45_DATA_REG 0xe
#define MDIO_REG_GPHY_EEE_ADV 0x3c
#define MDIO_REG_GPHY_EEE_1G (0x1 << 2)
#define MDIO_REG_GPHY_EEE_100 (0x1 << 1)
#define MDIO_REG_GPHY_EEE_RESOLVED 0x803e
#define MDIO_REG_INTR_STATUS 0x1a
#define MDIO_REG_INTR_MASK 0x1b
#define MDIO_REG_INTR_MASK_LINK_STATUS (0x1 << 1)
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册