提交 4d3d769c 编写于 作者: L Linus Torvalds

Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ahci: redo stopping DMA engines on empty ports
  sata_sil24: fix kernel panic on ARM caused by unaligned access in sata_sil24
  ahci: add pci quirk for JMB362
  sata_via: explain the magic fix
......@@ -541,29 +541,11 @@ static int ahci_scr_write(struct ata_link *link, unsigned int sc_reg, u32 val)
return -EINVAL;
}
static int ahci_is_device_present(void __iomem *port_mmio)
{
u8 status = readl(port_mmio + PORT_TFDATA) & 0xff;
/* Make sure PxTFD.STS.BSY and PxTFD.STS.DRQ are 0 */
if (status & (ATA_BUSY | ATA_DRQ))
return 0;
/* Make sure PxSSTS.DET is 3h */
status = readl(port_mmio + PORT_SCR_STAT) & 0xf;
if (status != 3)
return 0;
return 1;
}
void ahci_start_engine(struct ata_port *ap)
{
void __iomem *port_mmio = ahci_port_base(ap);
u32 tmp;
if (!ahci_is_device_present(port_mmio))
return;
/* start DMA */
tmp = readl(port_mmio + PORT_CMD);
tmp |= PORT_CMD_START;
......@@ -1892,6 +1874,9 @@ static void ahci_error_handler(struct ata_port *ap)
}
sata_pmp_error_handler(ap);
if (!ata_dev_enabled(ap->link.device))
ahci_stop_engine(ap);
}
static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
......
......@@ -539,12 +539,12 @@ static void sil24_config_port(struct ata_port *ap)
writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR);
/* zero error counters. */
writel(0x8000, port + PORT_DECODE_ERR_THRESH);
writel(0x8000, port + PORT_CRC_ERR_THRESH);
writel(0x8000, port + PORT_HSHK_ERR_THRESH);
writel(0x0000, port + PORT_DECODE_ERR_CNT);
writel(0x0000, port + PORT_CRC_ERR_CNT);
writel(0x0000, port + PORT_HSHK_ERR_CNT);
writew(0x8000, port + PORT_DECODE_ERR_THRESH);
writew(0x8000, port + PORT_CRC_ERR_THRESH);
writew(0x8000, port + PORT_HSHK_ERR_THRESH);
writew(0x0000, port + PORT_DECODE_ERR_CNT);
writew(0x0000, port + PORT_CRC_ERR_CNT);
writew(0x0000, port + PORT_HSHK_ERR_CNT);
/* always use 64bit activation */
writel(PORT_CS_32BIT_ACTV, port + PORT_CTRL_CLR);
......
......@@ -578,10 +578,24 @@ static void svia_configure(struct pci_dev *pdev)
/*
* vt6421 has problems talking to some drives. The following
* is the magic fix from Joseph Chan <JosephChan@via.com.tw>.
* Please add proper documentation if possible.
* is the fix from Joseph Chan <JosephChan@via.com.tw>.
*
* When host issues HOLD, device may send up to 20DW of data
* before acknowledging it with HOLDA and the host should be
* able to buffer them in FIFO. Unfortunately, some WD drives
* send upto 40DW before acknowledging HOLD and, in the
* default configuration, this ends up overflowing vt6421's
* FIFO, making the controller abort the transaction with
* R_ERR.
*
* Rx52[2] is the internal 128DW FIFO Flow control watermark
* adjusting mechanism enable bit and the default value 0
* means host will issue HOLD to device when the left FIFO
* size goes below 32DW. Setting it to 1 makes the watermark
* 64DW.
*
* https://bugzilla.kernel.org/show_bug.cgi?id=15173
* http://article.gmane.org/gmane.linux.ide/46352
*/
if (pdev->device == 0x3249) {
pci_read_config_byte(pdev, 0x52, &tmp8);
......
......@@ -1457,7 +1457,8 @@ static void quirk_jmicron_ata(struct pci_dev *pdev)
conf5 &= ~(1 << 24); /* Clear bit 24 */
switch (pdev->device) {
case PCI_DEVICE_ID_JMICRON_JMB360:
case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */
case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */
/* The controller should be in single function ahci mode */
conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */
break;
......@@ -1493,12 +1494,14 @@ static void quirk_jmicron_ata(struct pci_dev *pdev)
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
......
......@@ -2321,6 +2321,7 @@
#define PCI_VENDOR_ID_JMICRON 0x197B
#define PCI_DEVICE_ID_JMICRON_JMB360 0x2360
#define PCI_DEVICE_ID_JMICRON_JMB361 0x2361
#define PCI_DEVICE_ID_JMICRON_JMB362 0x2362
#define PCI_DEVICE_ID_JMICRON_JMB363 0x2363
#define PCI_DEVICE_ID_JMICRON_JMB365 0x2365
#define PCI_DEVICE_ID_JMICRON_JMB366 0x2366
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册