brcmsmac: remove si_pmu_init() and si_pmu_res_init()

This is already done by bcma_pmu_init() and bcma_pmu_resources_init() in bcma.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/brcm80211/brcmsmac/aiutils.c

@@ -503,9 +503,7 @@ static struct si_info *ai_doattach(struct si_info *sii,
 
 	/* PMU specific initializations */
 	if (ai_get_cccaps(sih) & CC_CAP_PMU) {
-		si_pmu_init(sih);
 		(void)si_pmu_measure_alpclk(sih);
-		si_pmu_res_init(sih);
 	}
 
 	/* setup the GPIO based LED powersave register */

drivers/net/wireless/brcm80211/brcmsmac/pmu.c

@@ -108,37 +108,6 @@
 #define	RES4313_HT_AVAIL_RSRC		14
 #define	RES4313_MACPHY_CLK_AVAIL_RSRC	15
 
-/* Determine min/max rsrc masks. Value 0 leaves hardware at default. */
-static void si_pmu_res_masks(struct si_pub *sih, u32 * pmin, u32 * pmax)
-{
-	u32 min_mask = 0, max_mask = 0;
-	uint rsrcs;
-
-	/* # resources */
-	rsrcs = (ai_get_pmucaps(sih) & PCAP_RC_MASK) >> PCAP_RC_SHIFT;
-
-	/* determine min/max rsrc masks */
-	switch (ai_get_chip_id(sih)) {
-	case BCM43224_CHIP_ID:
-	case BCM43225_CHIP_ID:
-		/* ??? */
-		break;
-
-	case BCM4313_CHIP_ID:
-		min_mask = PMURES_BIT(RES4313_BB_PU_RSRC) |
-		    PMURES_BIT(RES4313_XTAL_PU_RSRC) |
-		    PMURES_BIT(RES4313_ALP_AVAIL_RSRC) |
-		    PMURES_BIT(RES4313_BB_PLL_PWRSW_RSRC);
-		max_mask = 0xffff;
-		break;
-	default:
-		break;
-	}
-
-	*pmin = min_mask;
-	*pmax = max_mask;
-}
-
 void si_pmu_spuravoid_pllupdate(struct si_pub *sih, u8 spuravoid)
 {
 	u32 tmp = 0;
@@ -284,51 +253,6 @@ u32 si_pmu_alp_clock(struct si_pub *sih)
 	return clock;
 }
 
-/* initialize PMU */
-void si_pmu_init(struct si_pub *sih)
-{
-	struct si_info *sii = container_of(sih, struct si_info, pub);
-	struct bcma_device *core;
-
-	/* select chipc */
-	core = sii->icbus->drv_cc.core;
-
-	if (ai_get_pmurev(sih) == 1)
-		bcma_mask32(core, CHIPCREGOFFS(pmucontrol),
-			    ~PCTL_NOILP_ON_WAIT);
-	else if (ai_get_pmurev(sih) >= 2)
-		bcma_set32(core, CHIPCREGOFFS(pmucontrol), PCTL_NOILP_ON_WAIT);
-}
-
-/* initialize PMU resources */
-void si_pmu_res_init(struct si_pub *sih)
-{
-	struct si_info *sii = container_of(sih, struct si_info, pub);
-	struct bcma_device *core;
-	u32 min_mask = 0, max_mask = 0;
-
-	/* select to chipc */
-	core = sii->icbus->drv_cc.core;
-
-	/* Determine min/max rsrc masks */
-	si_pmu_res_masks(sih, &min_mask, &max_mask);
-
-	/* It is required to program max_mask first and then min_mask */
-
-	/* Program max resource mask */
-
-	if (max_mask)
-		bcma_write32(core, CHIPCREGOFFS(max_res_mask), max_mask);
-
-	/* Program min resource mask */
-
-	if (min_mask)
-		bcma_write32(core, CHIPCREGOFFS(min_res_mask), min_mask);
-
-	/* Add some delay; allow resources to come up and settle. */
-	mdelay(2);
-}
-
 u32 si_pmu_measure_alpclk(struct si_pub *sih)
 {
 	struct si_info *sii = container_of(sih, struct si_info, pub);

drivers/net/wireless/brcm80211/brcmsmac/pmu.h

@@ -28,8 +28,6 @@ extern u32 si_pmu_alp_clock(struct si_pub *sih);
 extern void si_pmu_pllupd(struct si_pub *sih);
 extern void si_pmu_spuravoid_pllupdate(struct si_pub *sih, u8 spuravoid);
 extern u32 si_pmu_pllcontrol(struct si_pub *sih, uint reg, u32 mask, u32 val);
-extern void si_pmu_init(struct si_pub *sih);
-extern void si_pmu_res_init(struct si_pub *sih);
 extern u32 si_pmu_measure_alpclk(struct si_pub *sih);
 
 #endif /* _BRCM_PMU_H_ */