提交 477f949e 编写于 作者: R Ralf Baechle

[MIPS] Sibyte: CONFIG_SIBYTE_SB1250_DUART -> CONFIG_SERIAL_SB1250_DUART

This is needed since the Sibyte serial driver was exchanged.

Issue report by Imre Kaloz <kaloz@openwrt.org>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
上级 7acae224
......@@ -663,8 +663,8 @@ CONFIG_MOXA_SMARTIO_NEW=m
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
CONFIG_SIBYTE_SB1250_DUART=y
CONFIG_SIBYTE_SB1250_DUART_CONSOLE=y
CONFIG_SERIAL_SB1250_DUART=y
CONFIG_SERIAL_SB1250_DUART_CONSOLE=y
#
# Serial drivers
......
......@@ -655,8 +655,8 @@ CONFIG_MOXA_SMARTIO_NEW=m
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
CONFIG_SIBYTE_SB1250_DUART=y
CONFIG_SIBYTE_SB1250_DUART_CONSOLE=y
CONFIG_SERIAL_SB1250_DUART=y
CONFIG_SERIAL_SB1250_DUART_CONSOLE=y
#
# Serial drivers
......
......@@ -76,7 +76,7 @@ __setup("nokgdb", nokgdb);
/* Default to UART1 */
int kgdb_port = 1;
#ifdef CONFIG_SIBYTE_SB1250_DUART
#ifdef CONFIG_SERIAL_SB1250_DUART
extern char sb1250_duart_present[];
#endif
#endif
......@@ -404,7 +404,7 @@ void __init arch_init_irq(void)
if (kgdb_flag) {
kgdb_irq = K_BCM1480_INT_UART_0 + kgdb_port;
#ifdef CONFIG_SIBYTE_SB1250_DUART
#ifdef CONFIG_SERIAL_SB1250_DUART
sb1250_duart_present[kgdb_port] = 0;
#endif
/* Setup uart 1 settings, mapper */
......
......@@ -46,7 +46,7 @@ static int cfe_console_setup(struct console *cons, char *str)
/* XXXKW think about interaction with 'console=' cmdline arg */
/* If none of the console options are configured, the build will break. */
if (cfe_getenv("BOOT_CONSOLE", consdev, 32) >= 0) {
#ifdef CONFIG_SIBYTE_SB1250_DUART
#ifdef CONFIG_SERIAL_SB1250_DUART
if (!strcmp(consdev, "uart0")) {
setleds("u0cn");
} else if (!strcmp(consdev, "uart1")) {
......
......@@ -61,7 +61,7 @@ static int kgdb_irq;
/* Default to UART1 */
int kgdb_port = 1;
#ifdef CONFIG_SIBYTE_SB1250_DUART
#ifdef CONFIG_SERIAL_SB1250_DUART
extern char sb1250_duart_present[];
#endif
#endif
......@@ -359,7 +359,7 @@ void __init arch_init_irq(void)
if (kgdb_flag) {
kgdb_irq = K_INT_UART_0 + kgdb_port;
#ifdef CONFIG_SIBYTE_SB1250_DUART
#ifdef CONFIG_SERIAL_SB1250_DUART
sb1250_duart_present[kgdb_port] = 0;
#endif
/* Setup uart 1 settings, mapper */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册