Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (w83627ehf) Add support for the W83627UHG
  hwmon: (w83627ehf) Clean up probe function
  hwmon: (w83627ehf) Properly report PECI and AMD-SI sensor types
  hwmon: Use i2c_smbus_{read,write}_word_swapped
  hwmon: (smsc47b397) Fix checkpatch errors
  hwmon: (lm90) Make code more readable
  hwmon: (lm90) Fix warnings
  hwmon: (ibmaem) Avoid repeated memory allocations
  hwmon: (ibmaem) Make instance initializations independent
  hwmon: (ibmaem) Fix error paths
  hwmon: (lm73) Make detection less problematic
  hwmon: Avoid building drivers for powerpc that read/write ISA addresses

Documentation/hwmon/w83627ehf

@@ -14,6 +14,10 @@ Supported chips:
     Prefix: 'w83627dhg'
     Addresses scanned: ISA address retrieved from Super I/O registers
     Datasheet: not available
+  * Winbond W83627UHG
+    Prefix: 'w83627uhg'
+    Addresses scanned: ISA address retrieved from Super I/O registers
+    Datasheet: available from www.nuvoton.com
   * Winbond W83667HG
     Prefix: 'w83667hg'
     Addresses scanned: ISA address retrieved from Super I/O registers
@@ -42,14 +46,13 @@ Description
 -----------
 
 This driver implements support for the Winbond W83627EHF, W83627EHG,
-W83627DHG, W83627DHG-P, W83667HG, W83667HG-B, W83667HG-I (NCT6775F),
-and NCT6776F super I/O chips. We will refer to them collectively as
-Winbond chips.
-
-The chips implement three temperature sensors (up to four for 667HG-B, and nine
-for NCT6775F and NCT6776F), five fan rotation speed sensors, ten analog voltage
-sensors (only nine for the 627DHG), one VID (6 pins for the 627EHF/EHG, 8 pins
-for the 627DHG and 667HG), alarms with beep warnings (control unimplemented),
+W83627DHG, W83627DHG-P, W83627UHG, W83667HG, W83667HG-B, W83667HG-I
+(NCT6775F), and NCT6776F super I/O chips. We will refer to them collectively
+as Winbond chips.
+
+The chips implement 2 to 4 temperature sensors (9 for NCT6775F and NCT6776F),
+2 to 5 fan rotation speed sensors, 8 to 10 analog voltage sensors, one VID
+(except for 627UHG), alarms with beep warnings (control unimplemented),
 and some automatic fan regulation strategies (plus manual fan control mode).
 
 The temperature sensor sources on W82677HG-B, NCT6775F, and NCT6776F are
@@ -86,17 +89,16 @@ follows:
 
 temp1 -> pwm1
 temp2 -> pwm2
-temp3 -> pwm3
+temp3 -> pwm3 (not on 627UHG)
 prog  -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not
 	       supported by the driver)
 
 /sys files
 ----------
 
-name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG,
-       it is set to "w83627ehf", for the W83627DHG it is set to "w83627dhg",
-       for the W83667HG and W83667HG-B it is set to "w83667hg", for NCT6775F it
-       is set to "nct6775", and for NCT6776F it is set to "nct6776".
+name - this is a standard hwmon device entry, it contains the name of
+       the device (see the prefix in the list of supported devices at
+       the top of this file)
 
 pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range:
 	   0 (stop) to 255 (full)

drivers/hwmon/Kconfig

@@ -335,6 +335,7 @@ config SENSORS_I5K_AMB
 
 config SENSORS_F71805F
 	tristate "Fintek F71805F/FG, F71806F/FG and F71872F/FG"
+	depends on !PPC
 	help
 	  If you say yes here you get support for hardware monitoring
 	  features of the Fintek F71805F/FG, F71806F/FG and F71872F/FG
@@ -345,6 +346,7 @@ config SENSORS_F71805F
 
 config SENSORS_F71882FG
 	tristate "Fintek F71882FG and compatibles"
+	depends on !PPC
 	help
 	  If you say yes here you get support for hardware monitoring
 	  features of many Fintek Super-I/O (LPC) chips. The currently
@@ -468,6 +470,7 @@ config SENSORS_IBMPEX
 
 config SENSORS_IT87
 	tristate "ITE IT87xx and compatibles"
+	depends on !PPC
 	select HWMON_VID
 	help
 	  If you say yes here you get support for ITE IT8705F, IT8712F,
@@ -824,6 +827,7 @@ config SENSORS_NTC_THERMISTOR
 
 config SENSORS_PC87360
 	tristate "National Semiconductor PC87360 family"
+	depends on !PPC
 	select HWMON_VID
 	help
 	  If you say yes here you get access to the hardware monitoring
@@ -837,6 +841,7 @@ config SENSORS_PC87360
 
 config SENSORS_PC87427
 	tristate "National Semiconductor PC87427"
+	depends on !PPC
 	help
 	  If you say yes here you get access to the hardware monitoring
 	  functions of the National Semiconductor PC87427 Super-I/O chip.
@@ -928,7 +933,7 @@ config SENSORS_SMM665
 
 config SENSORS_DME1737
 	tristate "SMSC DME1737, SCH311x and compatibles"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C && EXPERIMENTAL && !PPC
 	select HWMON_VID
 	help
 	  If you say yes here you get support for the hardware monitoring
@@ -970,6 +975,7 @@ config SENSORS_EMC6W201
 
 config SENSORS_SMSC47M1
 	tristate "SMSC LPC47M10x and compatibles"
+	depends on !PPC
 	help
 	  If you say yes here you get support for the integrated fan
 	  monitoring and control capabilities of the SMSC LPC47B27x,
@@ -1003,7 +1009,7 @@ config SENSORS_SMSC47M192
 
 config SENSORS_SMSC47B397
 	tristate "SMSC LPC47B397-NC"
-	depends on EXPERIMENTAL
+	depends on EXPERIMENTAL && !PPC
 	help
 	  If you say yes here you get support for the SMSC LPC47B397-NC
 	  sensor chip.
@@ -1017,6 +1023,7 @@ config SENSORS_SCH56XX_COMMON
 
 config SENSORS_SCH5627
 	tristate "SMSC SCH5627"
+	depends on !PPC
 	select SENSORS_SCH56XX_COMMON
 	help
 	  If you say yes here you get support for the hardware monitoring
@@ -1027,6 +1034,7 @@ config SENSORS_SCH5627
 
 config SENSORS_SCH5636
 	tristate "SMSC SCH5636"
+	depends on !PPC
 	select SENSORS_SCH56XX_COMMON
 	help
 	  SMSC SCH5636 Super I/O chips include an embedded microcontroller for
@@ -1150,6 +1158,7 @@ config SENSORS_VIA686A
 
 config SENSORS_VT1211
 	tristate "VIA VT1211"
+	depends on !PPC
 	select HWMON_VID
 	help
 	  If you say yes here then you get support for hardware monitoring
@@ -1262,6 +1271,7 @@ config SENSORS_W83L786NG
 
 config SENSORS_W83627HF
 	tristate "Winbond W83627HF, W83627THF, W83637HF, W83687THF, W83697HF"
+	depends on !PPC
 	select HWMON_VID
 	help
 	  If you say yes here you get support for the Winbond W836X7 series
@@ -1272,7 +1282,8 @@ config SENSORS_W83627HF
 	  will be called w83627hf.
 
 config SENSORS_W83627EHF
-	tristate "Winbond W83627EHF/EHG/DHG, W83667HG, NCT6775F, NCT6776F"
+	tristate "Winbond W83627EHF/EHG/DHG/UHG, W83667HG, NCT6775F, NCT6776F"
+	depends on !PPC
 	select HWMON_VID
 	help
 	  If you say yes here you get support for the hardware
@@ -1281,7 +1292,8 @@ config SENSORS_W83627EHF
 	  This driver also supports the W83627EHG, which is the lead-free
 	  version of the W83627EHF, and the W83627DHG, which is a similar
 	  chip suited for specific Intel processors that use PECI such as
-	  the Core 2 Duo.
+	  the Core 2 Duo. And also the W83627UHG, which is a stripped down
+	  version of the W83627DHG (as far as hardware monitoring goes.)
 
 	  This driver also supports Nuvoton W83667HG, W83667HG-B, NCT6775F
 	  (also known as W83667HG-I), and NCT6776F.

drivers/hwmon/ad7414.c

@@ -58,10 +58,9 @@ static inline int ad7414_temp_from_reg(s16 reg)
 
 static inline int ad7414_read(struct i2c_client *client, u8 reg)
 {
-	if (reg == AD7414_REG_TEMP) {
-		int value = i2c_smbus_read_word_data(client, reg);
-		return (value < 0) ? value : swab16(value);
-	} else
+	if (reg == AD7414_REG_TEMP)
+		return i2c_smbus_read_word_swapped(client, reg);
+	else
 		return i2c_smbus_read_byte_data(client, reg);
 }
 

drivers/hwmon/ad7418.c

@@ -76,20 +76,6 @@ static struct i2c_driver ad7418_driver = {
 	.id_table	= ad7418_id,
 };
 
-/* All registers are word-sized, except for the configuration registers.
- * AD7418 uses a high-byte first convention. Do NOT use those functions to
- * access the configuration registers CONF and CONF2, as they are byte-sized.
- */
-static inline int ad7418_read(struct i2c_client *client, u8 reg)
-{
-	return swab16(i2c_smbus_read_word_data(client, reg));
-}
-
-static inline int ad7418_write(struct i2c_client *client, u8 reg, u16 value)
-{
-	return i2c_smbus_write_word_data(client, reg, swab16(value));
-}
-
 static void ad7418_init_client(struct i2c_client *client)
 {
 	struct ad7418_data *data = i2c_get_clientdata(client);
@@ -128,7 +114,9 @@ static struct ad7418_data *ad7418_update_device(struct device *dev)
 		udelay(30);
 
 		for (i = 0; i < 3; i++) {
-			data->temp[i] = ad7418_read(client, AD7418_REG_TEMP[i]);
+			data->temp[i] =
+				i2c_smbus_read_word_swapped(client,
+						AD7418_REG_TEMP[i]);
 		}
 
 		for (i = 0, ch = 4; i < data->adc_max; i++, ch--) {
@@ -138,11 +126,12 @@ static struct ad7418_data *ad7418_update_device(struct device *dev)
 
 			udelay(15);
 			data->in[data->adc_max - 1 - i] =
-				ad7418_read(client, AD7418_REG_ADC);
+				i2c_smbus_read_word_swapped(client,
+						AD7418_REG_ADC);
 		}
 
 		/* restore old configuration value */
-		ad7418_write(client, AD7418_REG_CONF, cfg);
+		i2c_smbus_write_word_swapped(client, AD7418_REG_CONF, cfg);
 
 		data->last_updated = jiffies;
 		data->valid = 1;
@@ -182,7 +171,9 @@ static ssize_t set_temp(struct device *dev, struct device_attribute *devattr,
 
 	mutex_lock(&data->lock);
 	data->temp[attr->index] = LM75_TEMP_TO_REG(temp);
-	ad7418_write(client, AD7418_REG_TEMP[attr->index], data->temp[attr->index]);
+	i2c_smbus_write_word_swapped(client,
+				     AD7418_REG_TEMP[attr->index],
+				     data->temp[attr->index]);
 	mutex_unlock(&data->lock);
 	return count;
 }

drivers/hwmon/ads1015.c

@@ -59,19 +59,6 @@ struct ads1015_data {
 	struct ads1015_channel_data channel_data[ADS1015_CHANNELS];
 };
 
-static s32 ads1015_read_reg(struct i2c_client *client, unsigned int reg)
-{
-	s32 data = i2c_smbus_read_word_data(client, reg);
-
-	return (data < 0) ? data : swab16(data);
-}
-
-static s32 ads1015_write_reg(struct i2c_client *client, unsigned int reg,
-			     u16 val)
-{
-	return i2c_smbus_write_word_data(client, reg, swab16(val));
-}
-
 static int ads1015_read_value(struct i2c_client *client, unsigned int channel,
 			      int *value)
 {
@@ -87,7 +74,7 @@ static int ads1015_read_value(struct i2c_client *client, unsigned int channel,
 	mutex_lock(&data->update_lock);
 
 	/* get channel parameters */
-	res = ads1015_read_reg(client, ADS1015_CONFIG);
+	res = i2c_smbus_read_word_swapped(client, ADS1015_CONFIG);
 	if (res < 0)
 		goto err_unlock;
 	config = res;
@@ -101,13 +88,13 @@ static int ads1015_read_value(struct i2c_client *client, unsigned int channel,
 	config |= (pga & 0x0007) << 9;
 	config |= (data_rate & 0x0007) << 5;
 
-	res = ads1015_write_reg(client, ADS1015_CONFIG, config);
+	res = i2c_smbus_write_word_swapped(client, ADS1015_CONFIG, config);
 	if (res < 0)
 		goto err_unlock;
 
 	/* wait until conversion finished */
 	msleep(conversion_time_ms);
-	res = ads1015_read_reg(client, ADS1015_CONFIG);
+	res = i2c_smbus_read_word_swapped(client, ADS1015_CONFIG);
 	if (res < 0)
 		goto err_unlock;
 	config = res;
@@ -117,7 +104,7 @@ static int ads1015_read_value(struct i2c_client *client, unsigned int channel,
 		goto err_unlock;
 	}
 
-	res = ads1015_read_reg(client, ADS1015_CONVERSION);
+	res = i2c_smbus_read_word_swapped(client, ADS1015_CONVERSION);
 	if (res < 0)
 		goto err_unlock;
 	conversion = res;

drivers/hwmon/ads7828.c

@@ -74,13 +74,6 @@ static int ads7828_detect(struct i2c_client *client,
 static int ads7828_probe(struct i2c_client *client,
 			 const struct i2c_device_id *id);
 
-/* The ADS7828 returns the 12-bit sample in two bytes,
-	these are read as a word then byte-swapped */
-static u16 ads7828_read_value(struct i2c_client *client, u8 reg)
-{
-	return swab16(i2c_smbus_read_word_data(client, reg));
-}
-
 static inline u8 channel_cmd_byte(int ch)
 {
 	/* cmd byte C2,C1,C0 - see datasheet */
@@ -104,7 +97,8 @@ static struct ads7828_data *ads7828_update_device(struct device *dev)
 
 		for (ch = 0; ch < ADS7828_NCH; ch++) {
 			u8 cmd = channel_cmd_byte(ch);
-			data->adc_input[ch] = ads7828_read_value(client, cmd);
+			data->adc_input[ch] =
+				i2c_smbus_read_word_swapped(client, cmd);
 		}
 		data->last_updated = jiffies;
 		data->valid = 1;
@@ -203,7 +197,7 @@ static int ads7828_detect(struct i2c_client *client,
 	for (ch = 0; ch < ADS7828_NCH; ch++) {
 		u16 in_data;
 		u8 cmd = channel_cmd_byte(ch);
-		in_data = ads7828_read_value(client, cmd);
+		in_data = i2c_smbus_read_word_swapped(client, cmd);
 		if (in_data & 0xF000) {
 			pr_debug("%s : Doesn't look like an ads7828 device\n",
 				 __func__);

drivers/hwmon/asb100.c

@@ -829,17 +829,17 @@ static int asb100_read_value(struct i2c_client *client, u16 reg)
 		/* convert from ISA to LM75 I2C addresses */
 		switch (reg & 0xff) {
 		case 0x50: /* TEMP */
-			res = swab16(i2c_smbus_read_word_data(cl, 0));
+			res = i2c_smbus_read_word_swapped(cl, 0);
 			break;
 		case 0x52: /* CONFIG */
 			res = i2c_smbus_read_byte_data(cl, 1);
 			break;
 		case 0x53: /* HYST */
-			res = swab16(i2c_smbus_read_word_data(cl, 2));
+			res = i2c_smbus_read_word_swapped(cl, 2);
 			break;
 		case 0x55: /* MAX */
 		default:
-			res = swab16(i2c_smbus_read_word_data(cl, 3));
+			res = i2c_smbus_read_word_swapped(cl, 3);
 			break;
 		}
 	}
@@ -877,10 +877,10 @@ static void asb100_write_value(struct i2c_client *client, u16 reg, u16 value)
 			i2c_smbus_write_byte_data(cl, 1, value & 0xff);
 			break;
 		case 0x53: /* HYST */
-			i2c_smbus_write_word_data(cl, 2, swab16(value));
+			i2c_smbus_write_word_swapped(cl, 2, value);
 			break;
 		case 0x55: /* MAX */
-			i2c_smbus_write_word_data(cl, 3, swab16(value));
+			i2c_smbus_write_word_swapped(cl, 3, value);
 			break;
 		}
 	}

drivers/hwmon/ds1621.c

@@ -80,24 +80,6 @@ struct ds1621_data {
 	u8 conf;			/* Register encoding, combined */
 };
 
-/* Temperature registers are word-sized.
-   DS1621 uses a high-byte first convention, which is exactly opposite to
-   the SMBus standard. */
-static int ds1621_read_temp(struct i2c_client *client, u8 reg)
-{
-	int ret;
-
-	ret = i2c_smbus_read_word_data(client, reg);
-	if (ret < 0)
-		return ret;
-	return swab16(ret);
-}
-
-static int ds1621_write_temp(struct i2c_client *client, u8 reg, u16 value)
-{
-	return i2c_smbus_write_word_data(client, reg, swab16(value));
-}
-
 static void ds1621_init_client(struct i2c_client *client)
 {
 	u8 conf, new_conf;
@@ -136,7 +118,7 @@ static struct ds1621_data *ds1621_update_client(struct device *dev)
 		data->conf = i2c_smbus_read_byte_data(client, DS1621_REG_CONF);
 
 		for (i = 0; i < ARRAY_SIZE(data->temp); i++)
-			data->temp[i] = ds1621_read_temp(client,
+			data->temp[i] = i2c_smbus_read_word_swapped(client,
 							 DS1621_REG_TEMP[i]);
 
 		/* reset alarms if necessary */
@@ -177,8 +159,8 @@ static ssize_t set_temp(struct device *dev, struct device_attribute *da,
 
 	mutex_lock(&data->update_lock);
 	data->temp[attr->index] = val;
-	ds1621_write_temp(client, DS1621_REG_TEMP[attr->index],
-			  data->temp[attr->index]);
+	i2c_smbus_write_word_swapped(client, DS1621_REG_TEMP[attr->index],
+				     data->temp[attr->index]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }

drivers/hwmon/ds620.c

@@ -75,33 +75,13 @@ struct ds620_data {
 	s16 temp[3];		/* Register values, word */
 };
 
-/*
- *  Temperature registers are word-sized.
- *  DS620 uses a high-byte first convention, which is exactly opposite to
- *  the SMBus standard.
- */
-static int ds620_read_temp(struct i2c_client *client, u8 reg)
-{
-	int ret;
-
-	ret = i2c_smbus_read_word_data(client, reg);
-	if (ret < 0)
-		return ret;
-	return swab16(ret);
-}
-
-static int ds620_write_temp(struct i2c_client *client, u8 reg, u16 value)
-{
-	return i2c_smbus_write_word_data(client, reg, swab16(value));
-}
-
 static void ds620_init_client(struct i2c_client *client)
 {
 	struct ds620_platform_data *ds620_info = client->dev.platform_data;
 	u16 conf, new_conf;
 
 	new_conf = conf =
-	    swab16(i2c_smbus_read_word_data(client, DS620_REG_CONF));
+	    i2c_smbus_read_word_swapped(client, DS620_REG_CONF);
 
 	/* switch to continuous conversion mode */
 	new_conf &= ~DS620_REG_CONFIG_1SHOT;
@@ -118,8 +98,7 @@ static void ds620_init_client(struct i2c_client *client)
 	new_conf |= DS620_REG_CONFIG_R1 | DS620_REG_CONFIG_R0;
 
 	if (conf != new_conf)
-		i2c_smbus_write_word_data(client, DS620_REG_CONF,
-					  swab16(new_conf));
+		i2c_smbus_write_word_swapped(client, DS620_REG_CONF, new_conf);
 
 	/* start conversion */
 	i2c_smbus_write_byte(client, DS620_COM_START);
@@ -141,8 +120,8 @@ static struct ds620_data *ds620_update_client(struct device *dev)
 		dev_dbg(&client->dev, "Starting ds620 update\n");
 
 		for (i = 0; i < ARRAY_SIZE(data->temp); i++) {
-			res = ds620_read_temp(client,
-					      DS620_REG_TEMP[i]);
+			res = i2c_smbus_read_word_swapped(client,
+							  DS620_REG_TEMP[i]);
 			if (res < 0) {
 				ret = ERR_PTR(res);
 				goto abort;
@@ -191,8 +170,8 @@ static ssize_t set_temp(struct device *dev, struct device_attribute *da,
 
 	mutex_lock(&data->update_lock);
 	data->temp[attr->index] = val;
-	ds620_write_temp(client, DS620_REG_TEMP[attr->index],
-			 data->temp[attr->index]);
+	i2c_smbus_write_word_swapped(client, DS620_REG_TEMP[attr->index],
+				     data->temp[attr->index]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -210,16 +189,15 @@ static ssize_t show_alarm(struct device *dev, struct device_attribute *da,
 		return PTR_ERR(data);
 
 	/* reset alarms if necessary */
-	res = i2c_smbus_read_word_data(client, DS620_REG_CONF);
+	res = i2c_smbus_read_word_swapped(client, DS620_REG_CONF);
 	if (res < 0)
 		return res;
 
-	conf = swab16(res);
-	new_conf = conf;
+	new_conf = conf = res;
 	new_conf &= ~attr->index;
 	if (conf != new_conf) {
-		res = i2c_smbus_write_word_data(client, DS620_REG_CONF,
-						swab16(new_conf));
+		res = i2c_smbus_write_word_swapped(client, DS620_REG_CONF,
+						   new_conf);
 		if (res < 0)
 			return res;
 	}

drivers/hwmon/gl518sm.c

@@ -591,7 +591,7 @@ static int gl518_remove(struct i2c_client *client)
 static int gl518_read_value(struct i2c_client *client, u8 reg)
 {
 	if ((reg >= 0x07) && (reg <= 0x0c))
-		return swab16(i2c_smbus_read_word_data(client, reg));
+		return i2c_smbus_read_word_swapped(client, reg);
 	else
 		return i2c_smbus_read_byte_data(client, reg);
 }
@@ -599,7 +599,7 @@ static int gl518_read_value(struct i2c_client *client, u8 reg)
 static int gl518_write_value(struct i2c_client *client, u8 reg, u16 value)
 {
 	if ((reg >= 0x07) && (reg <= 0x0c))
-		return i2c_smbus_write_word_data(client, reg, swab16(value));
+		return i2c_smbus_write_word_swapped(client, reg, value);
 	else
 		return i2c_smbus_write_byte_data(client, reg, value);
 }

drivers/hwmon/gl520sm.c

@@ -821,7 +821,7 @@ static int gl520_remove(struct i2c_client *client)
 static int gl520_read_value(struct i2c_client *client, u8 reg)
 {
 	if ((reg >= 0x07) && (reg <= 0x0c))
-		return swab16(i2c_smbus_read_word_data(client, reg));
+		return i2c_smbus_read_word_swapped(client, reg);
 	else
 		return i2c_smbus_read_byte_data(client, reg);
 }
@@ -829,7 +829,7 @@ static int gl520_read_value(struct i2c_client *client, u8 reg)
 static int gl520_write_value(struct i2c_client *client, u8 reg, u16 value)
 {
 	if ((reg >= 0x07) && (reg <= 0x0c))
-		return i2c_smbus_write_word_data(client, reg, swab16(value));
+		return i2c_smbus_write_word_swapped(client, reg, value);
 	else
 		return i2c_smbus_write_byte_data(client, reg, value);
 }

drivers/hwmon/ibmaem.c

@@ -147,8 +147,9 @@ struct aem_data {
 	int			id;
 	struct aem_ipmi_data	ipmi;
 
-	/* Function to update sensors */
+	/* Function and buffer to update sensors */
 	void (*update)(struct aem_data *data);
+	struct aem_read_sensor_resp *rs_resp;
 
 	/*
 	 * AEM 1.x sensors:
@@ -245,8 +246,6 @@ static void aem_bmc_gone(int iface);
 static void aem_msg_handler(struct ipmi_recv_msg *msg, void *user_msg_data);
 
 static void aem_remove_sensors(struct aem_data *data);
-static int aem_init_aem1(struct aem_ipmi_data *probe);
-static int aem_init_aem2(struct aem_ipmi_data *probe);
 static int aem1_find_sensors(struct aem_data *data);
 static int aem2_find_sensors(struct aem_data *data);
 static void update_aem1_sensors(struct aem_data *data);
@@ -357,13 +356,14 @@ static void aem_msg_handler(struct ipmi_recv_msg *msg, void *user_msg_data)
 
 /* Sensor support functions */
 
-/* Read a sensor value */
+/* Read a sensor value; must be called with data->lock held */
 static int aem_read_sensor(struct aem_data *data, u8 elt, u8 reg,
 			   void *buf, size_t size)
 {
 	int rs_size, res;
 	struct aem_read_sensor_req rs_req;
-	struct aem_read_sensor_resp *rs_resp;
+	/* Use preallocated rx buffer */
+	struct aem_read_sensor_resp *rs_resp = data->rs_resp;
 	struct aem_ipmi_data *ipmi = &data->ipmi;
 
 	/* AEM registers are 1, 2, 4 or 8 bytes */
@@ -389,10 +389,6 @@ static int aem_read_sensor(struct aem_data *data, u8 elt, u8 reg,
 	ipmi->tx_message.data_len = sizeof(rs_req);
 
 	rs_size = sizeof(*rs_resp) + size;
-	rs_resp = kzalloc(rs_size, GFP_KERNEL);
-	if (!rs_resp)
-		return -ENOMEM;
-
 	ipmi->rx_msg_data = rs_resp;
 	ipmi->rx_msg_len = rs_size;
 
@@ -435,7 +431,6 @@ static int aem_read_sensor(struct aem_data *data, u8 elt, u8 reg,
 	res = 0;
 
 out:
-	kfree(rs_resp);
 	return res;
 }
 
@@ -493,6 +488,7 @@ static void aem_delete(struct aem_data *data)
 {
 	list_del(&data->list);
 	aem_remove_sensors(data);
+	kfree(data->rs_resp);
 	hwmon_device_unregister(data->hwmon_dev);
 	ipmi_destroy_user(data->ipmi.user);
 	platform_set_drvdata(data->pdev, NULL);
@@ -570,24 +566,31 @@ static int aem_init_aem1_inst(struct aem_ipmi_data *probe, u8 module_handle)
 	platform_set_drvdata(data->pdev, data);
 
 	/* Set up IPMI interface */
-	if (aem_init_ipmi_data(&data->ipmi, probe->interface,
-			       probe->bmc_device))
+	res = aem_init_ipmi_data(&data->ipmi, probe->interface,
+				 probe->bmc_device);
+	if (res)
 		goto ipmi_err;
 
 	/* Register with hwmon */
 	data->hwmon_dev = hwmon_device_register(&data->pdev->dev);
-
 	if (IS_ERR(data->hwmon_dev)) {
 		dev_err(&data->pdev->dev, "Unable to register hwmon "
 			"device for IPMI interface %d\n",
 			probe->interface);
+		res = PTR_ERR(data->hwmon_dev);
 		goto hwmon_reg_err;
 	}
 
 	data->update = update_aem1_sensors;
+	data->rs_resp = kzalloc(sizeof(*(data->rs_resp)) + 8, GFP_KERNEL);
+	if (!data->rs_resp) {
+		res = -ENOMEM;
+		goto alloc_resp_err;
+	}
 
 	/* Find sensors */
-	if (aem1_find_sensors(data))
+	res = aem1_find_sensors(data);
+	if (res)
 		goto sensor_err;
 
 	/* Add to our list of AEM devices */
@@ -599,6 +602,8 @@ static int aem_init_aem1_inst(struct aem_ipmi_data *probe, u8 module_handle)
 	return 0;
 
 sensor_err:
+	kfree(data->rs_resp);
+alloc_resp_err:
 	hwmon_device_unregister(data->hwmon_dev);
 hwmon_reg_err:
 	ipmi_destroy_user(data->ipmi.user);
@@ -614,7 +619,7 @@ static int aem_init_aem1_inst(struct aem_ipmi_data *probe, u8 module_handle)
 }
 
 /* Find and initialize all AEM1 instances */
-static int aem_init_aem1(struct aem_ipmi_data *probe)
+static void aem_init_aem1(struct aem_ipmi_data *probe)
 {
 	int num, i, err;
 
@@ -625,11 +630,8 @@ static int aem_init_aem1(struct aem_ipmi_data *probe)
 			dev_err(probe->bmc_device,
 				"Error %d initializing AEM1 0x%X\n",
 				err, i);
-			return err;
 		}
 	}
-
-	return 0;
 }
 
 /* Probe functions for AEM2 devices */
@@ -704,24 +706,31 @@ static int aem_init_aem2_inst(struct aem_ipmi_data *probe,
 	platform_set_drvdata(data->pdev, data);
 
 	/* Set up IPMI interface */
-	if (aem_init_ipmi_data(&data->ipmi, probe->interface,
-			       probe->bmc_device))
+	res = aem_init_ipmi_data(&data->ipmi, probe->interface,
+				 probe->bmc_device);
+	if (res)
 		goto ipmi_err;
 
 	/* Register with hwmon */
 	data->hwmon_dev = hwmon_device_register(&data->pdev->dev);
-
 	if (IS_ERR(data->hwmon_dev)) {
 		dev_err(&data->pdev->dev, "Unable to register hwmon "
 			"device for IPMI interface %d\n",
 			probe->interface);
+		res = PTR_ERR(data->hwmon_dev);
 		goto hwmon_reg_err;
 	}
 
 	data->update = update_aem2_sensors;
+	data->rs_resp = kzalloc(sizeof(*(data->rs_resp)) + 8, GFP_KERNEL);
+	if (!data->rs_resp) {
+		res = -ENOMEM;
+		goto alloc_resp_err;
+	}
 
 	/* Find sensors */
-	if (aem2_find_sensors(data))
+	res = aem2_find_sensors(data);
+	if (res)
 		goto sensor_err;
 
 	/* Add to our list of AEM devices */
@@ -733,6 +742,8 @@ static int aem_init_aem2_inst(struct aem_ipmi_data *probe,
 	return 0;
 
 sensor_err:
+	kfree(data->rs_resp);
+alloc_resp_err:
 	hwmon_device_unregister(data->hwmon_dev);
 hwmon_reg_err:
 	ipmi_destroy_user(data->ipmi.user);
@@ -748,7 +759,7 @@ static int aem_init_aem2_inst(struct aem_ipmi_data *probe,
 }
 
 /* Find and initialize all AEM2 instances */
-static int aem_init_aem2(struct aem_ipmi_data *probe)
+static void aem_init_aem2(struct aem_ipmi_data *probe)
 {
 	struct aem_find_instance_resp fi_resp;
 	int err;
@@ -767,12 +778,9 @@ static int aem_init_aem2(struct aem_ipmi_data *probe)
 			dev_err(probe->bmc_device,
 				"Error %d initializing AEM2 0x%X\n",
 				err, fi_resp.module_handle);
-			return err;
 		}
 		i++;
 	}
-
-	return 0;
 }
 
 /* Probe a BMC for AEM firmware instances */

drivers/hwmon/jc42.c

@@ -154,8 +154,6 @@ static int jc42_probe(struct i2c_client *client,
 		      const struct i2c_device_id *id);
 static int jc42_detect(struct i2c_client *client, struct i2c_board_info *info);
 static int jc42_remove(struct i2c_client *client);
-static int jc42_read_value(struct i2c_client *client, u8 reg);
-static int jc42_write_value(struct i2c_client *client, u8 reg, u16 value);
 
 static struct jc42_data *jc42_update_device(struct device *dev);
 
@@ -187,7 +185,7 @@ static int jc42_suspend(struct device *dev)
 	struct jc42_data *data = i2c_get_clientdata(client);
 
 	data->config |= JC42_CFG_SHUTDOWN;
-	jc42_write_value(client, JC42_REG_CONFIG, data->config);
+	i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG, data->config);
 	return 0;
 }
 
@@ -197,7 +195,7 @@ static int jc42_resume(struct device *dev)
 	struct jc42_data *data = i2c_get_clientdata(client);
 
 	data->config &= ~JC42_CFG_SHUTDOWN;
-	jc42_write_value(client, JC42_REG_CONFIG, data->config);
+	i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG, data->config);
 	return 0;
 }
 
@@ -315,7 +313,7 @@ static ssize_t set_##value(struct device *dev,				\
 		return -EINVAL;						\
 	mutex_lock(&data->update_lock);					\
 	data->value = jc42_temp_to_reg(val, data->extended);		\
-	err = jc42_write_value(client, reg, data->value);		\
+	err = i2c_smbus_write_word_swapped(client, reg, data->value);	\
 	if (err < 0)							\
 		ret = err;						\
 	mutex_unlock(&data->update_lock);				\
@@ -357,7 +355,8 @@ static ssize_t set_temp_crit_hyst(struct device *dev,
 	data->config = (data->config
 			& ~(JC42_CFG_HYST_MASK << JC42_CFG_HYST_SHIFT))
 	  | (hyst << JC42_CFG_HYST_SHIFT);
-	err = jc42_write_value(client, JC42_REG_CONFIG, data->config);
+	err = i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG,
+					   data->config);
 	if (err < 0)
 		ret = err;
 	mutex_unlock(&data->update_lock);
@@ -452,10 +451,10 @@ static int jc42_detect(struct i2c_client *new_client,
 				     I2C_FUNC_SMBUS_WORD_DATA))
 		return -ENODEV;
 
-	cap = jc42_read_value(new_client, JC42_REG_CAP);
-	config = jc42_read_value(new_client, JC42_REG_CONFIG);
-	manid = jc42_read_value(new_client, JC42_REG_MANID);
-	devid = jc42_read_value(new_client, JC42_REG_DEVICEID);
+	cap = i2c_smbus_read_word_swapped(new_client, JC42_REG_CAP);
+	config = i2c_smbus_read_word_swapped(new_client, JC42_REG_CONFIG);
+	manid = i2c_smbus_read_word_swapped(new_client, JC42_REG_MANID);
+	devid = i2c_smbus_read_word_swapped(new_client, JC42_REG_DEVICEID);
 
 	if (cap < 0 || config < 0 || manid < 0 || devid < 0)
 		return -ENODEV;
@@ -489,14 +488,14 @@ static int jc42_probe(struct i2c_client *new_client,
 	i2c_set_clientdata(new_client, data);
 	mutex_init(&data->update_lock);
 
-	cap = jc42_read_value(new_client, JC42_REG_CAP);
+	cap = i2c_smbus_read_word_swapped(new_client, JC42_REG_CAP);
 	if (cap < 0) {
 		err = -EINVAL;
 		goto exit_free;
 	}
 	data->extended = !!(cap & JC42_CAP_RANGE);
 
-	config = jc42_read_value(new_client, JC42_REG_CONFIG);
+	config = i2c_smbus_read_word_swapped(new_client, JC42_REG_CONFIG);
 	if (config < 0) {
 		err = -EINVAL;
 		goto exit_free;
@@ -504,7 +503,8 @@ static int jc42_probe(struct i2c_client *new_client,
 	data->orig_config = config;
 	if (config & JC42_CFG_SHUTDOWN) {
 		config &= ~JC42_CFG_SHUTDOWN;
-		jc42_write_value(new_client, JC42_REG_CONFIG, config);
+		i2c_smbus_write_word_swapped(new_client, JC42_REG_CONFIG,
+					     config);
 	}
 	data->config = config;
 
@@ -535,25 +535,12 @@ static int jc42_remove(struct i2c_client *client)
 	hwmon_device_unregister(data->hwmon_dev);
 	sysfs_remove_group(&client->dev.kobj, &jc42_group);
 	if (data->config != data->orig_config)
-		jc42_write_value(client, JC42_REG_CONFIG, data->orig_config);
+		i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG,
+					     data->orig_config);
 	kfree(data);
 	return 0;
 }
 
-/* All registers are word-sized. */
-static int jc42_read_value(struct i2c_client *client, u8 reg)
-{
-	int ret = i2c_smbus_read_word_data(client, reg);
-	if (ret < 0)
-		return ret;
-	return swab16(ret);
-}
-
-static int jc42_write_value(struct i2c_client *client, u8 reg, u16 value)
-{
-	return i2c_smbus_write_word_data(client, reg, swab16(value));
-}
-
 static struct jc42_data *jc42_update_device(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
@@ -564,28 +551,29 @@ static struct jc42_data *jc42_update_device(struct device *dev)
 	mutex_lock(&data->update_lock);
 
 	if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
-		val = jc42_read_value(client, JC42_REG_TEMP);
+		val = i2c_smbus_read_word_swapped(client, JC42_REG_TEMP);
 		if (val < 0) {
 			ret = ERR_PTR(val);
 			goto abort;
 		}
 		data->temp_input = val;
 
-		val = jc42_read_value(client, JC42_REG_TEMP_CRITICAL);
+		val = i2c_smbus_read_word_swapped(client,
+						  JC42_REG_TEMP_CRITICAL);
 		if (val < 0) {
 			ret = ERR_PTR(val);
 			goto abort;
 		}
 		data->temp_crit = val;
 
-		val = jc42_read_value(client, JC42_REG_TEMP_LOWER);
+		val = i2c_smbus_read_word_swapped(client, JC42_REG_TEMP_LOWER);
 		if (val < 0) {
 			ret = ERR_PTR(val);
 			goto abort;
 		}
 		data->temp_min = val;
 
-		val = jc42_read_value(client, JC42_REG_TEMP_UPPER);
+		val = i2c_smbus_read_word_swapped(client, JC42_REG_TEMP_UPPER);
 		if (val < 0) {
 			ret = ERR_PTR(val);
 			goto abort;

drivers/hwmon/lm73.c

@@ -34,7 +34,7 @@ static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4c,
 #define LM73_REG_CTRL		0x04
 #define LM73_REG_ID		0x07
 
-#define LM73_ID			0x9001 /* or 0x190 after a swab16() */
+#define LM73_ID			0x9001	/* 0x0190, byte-swapped */
 #define DRVNAME			"lm73"
 #define LM73_TEMP_MIN		(-40)
 #define LM73_TEMP_MAX		150
@@ -57,7 +57,7 @@ static ssize_t set_temp(struct device *dev, struct device_attribute *da,
 	/* Write value */
 	value = (short) SENSORS_LIMIT(temp/250, (LM73_TEMP_MIN*4),
 		(LM73_TEMP_MAX*4)) << 5;
-	i2c_smbus_write_word_data(client, attr->index, swab16(value));
+	i2c_smbus_write_word_swapped(client, attr->index, value);
 	return count;
 }
 
@@ -68,8 +68,8 @@ static ssize_t show_temp(struct device *dev, struct device_attribute *da,
 	struct i2c_client *client = to_i2c_client(dev);
 	/* use integer division instead of equivalent right shift to
 	   guarantee arithmetic shift and preserve the sign */
-	int temp = ((s16) (swab16(i2c_smbus_read_word_data(client,
-		attr->index)))*250) / 32;
+	int temp = ((s16) (i2c_smbus_read_word_swapped(client,
+		    attr->index))*250) / 32;
 	return sprintf(buf, "%d\n", temp);
 }
 
@@ -150,17 +150,31 @@ static int lm73_detect(struct i2c_client *new_client,
 			struct i2c_board_info *info)
 {
 	struct i2c_adapter *adapter = new_client->adapter;
-	u16 id;
-	u8 ctrl;
+	int id, ctrl, conf;
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
 					I2C_FUNC_SMBUS_WORD_DATA))
 		return -ENODEV;
 
+	/*
+	 * Do as much detection as possible with byte reads first, as word
+	 * reads can confuse other devices.
+	 */
+	ctrl = i2c_smbus_read_byte_data(new_client, LM73_REG_CTRL);
+	if (ctrl < 0 || (ctrl & 0x10))
+		return -ENODEV;
+
+	conf = i2c_smbus_read_byte_data(new_client, LM73_REG_CONF);
+	if (conf < 0 || (conf & 0x0c))
+		return -ENODEV;
+
+	id = i2c_smbus_read_byte_data(new_client, LM73_REG_ID);
+	if (id < 0 || id != (LM73_ID & 0xff))
+		return -ENODEV;
+
 	/* Check device ID */
 	id = i2c_smbus_read_word_data(new_client, LM73_REG_ID);
-	ctrl = i2c_smbus_read_byte_data(new_client, LM73_REG_CTRL);
-	if ((id != LM73_ID) || (ctrl & 0x10))
+	if (id < 0 || id != LM73_ID)
 		return -ENODEV;
 
 	strlcpy(info->type, "lm73", I2C_NAME_SIZE);

drivers/hwmon/lm75.c

@@ -384,13 +384,10 @@ static struct i2c_driver lm75_driver = {
  */
 static int lm75_read_value(struct i2c_client *client, u8 reg)
 {
-	int value;
-
 	if (reg == LM75_REG_CONF)
 		return i2c_smbus_read_byte_data(client, reg);
-
-	value = i2c_smbus_read_word_data(client, reg);
-	return (value < 0) ? value : swab16(value);
+	else
+		return i2c_smbus_read_word_swapped(client, reg);
 }
 
 static int lm75_write_value(struct i2c_client *client, u8 reg, u16 value)
@@ -398,7 +395,7 @@ static int lm75_write_value(struct i2c_client *client, u8 reg, u16 value)
 	if (reg == LM75_REG_CONF)
 		return i2c_smbus_write_byte_data(client, reg, value);
 	else
-		return i2c_smbus_write_word_data(client, reg, swab16(value));
+		return i2c_smbus_write_word_swapped(client, reg, value);
 }
 
 static struct lm75_data *lm75_update_device(struct device *dev)

drivers/hwmon/lm77.c

@@ -365,7 +365,7 @@ static u16 lm77_read_value(struct i2c_client *client, u8 reg)
 	if (reg == LM77_REG_CONF)
 		return i2c_smbus_read_byte_data(client, reg);
 	else
-		return swab16(i2c_smbus_read_word_data(client, reg));
+		return i2c_smbus_read_word_swapped(client, reg);
 }
 
 static int lm77_write_value(struct i2c_client *client, u8 reg, u16 value)
@@ -373,7 +373,7 @@ static int lm77_write_value(struct i2c_client *client, u8 reg, u16 value)
 	if (reg == LM77_REG_CONF)
 		return i2c_smbus_write_byte_data(client, reg, value);
 	else
-		return i2c_smbus_write_word_data(client, reg, swab16(value));
+		return i2c_smbus_write_word_swapped(client, reg, value);
 }
 
 static void lm77_init_client(struct i2c_client *client)

drivers/hwmon/lm90.c

@@ -1105,41 +1105,37 @@ static DEVICE_ATTR(pec, S_IWUSR | S_IRUGO, show_pec, set_pec);
  */
 
 /* Return 0 if detection is successful, -ENODEV otherwise */
-static int lm90_detect(struct i2c_client *new_client,
+static int lm90_detect(struct i2c_client *client,
 		       struct i2c_board_info *info)
 {
-	struct i2c_adapter *adapter = new_client->adapter;
-	int address = new_client->addr;
+	struct i2c_adapter *adapter = client->adapter;
+	int address = client->addr;
 	const char *name = NULL;
-	int man_id, chip_id, reg_config1, reg_config2, reg_convrate;
+	int man_id, chip_id, config1, config2, convrate;
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
 		return -ENODEV;
 
 	/* detection and identification */
-	if ((man_id = i2c_smbus_read_byte_data(new_client,
-						LM90_REG_R_MAN_ID)) < 0
-	 || (chip_id = i2c_smbus_read_byte_data(new_client,
-						LM90_REG_R_CHIP_ID)) < 0
-	 || (reg_config1 = i2c_smbus_read_byte_data(new_client,
-						LM90_REG_R_CONFIG1)) < 0
-	 || (reg_convrate = i2c_smbus_read_byte_data(new_client,
-						LM90_REG_R_CONVRATE)) < 0)
+	man_id = i2c_smbus_read_byte_data(client, LM90_REG_R_MAN_ID);
+	chip_id = i2c_smbus_read_byte_data(client, LM90_REG_R_CHIP_ID);
+	config1 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG1);
+	convrate = i2c_smbus_read_byte_data(client, LM90_REG_R_CONVRATE);
+	if (man_id < 0 || chip_id < 0 || config1 < 0 || convrate < 0)
 		return -ENODEV;
 
 	if (man_id == 0x01 || man_id == 0x5C || man_id == 0x41) {
-		reg_config2 = i2c_smbus_read_byte_data(new_client,
-						LM90_REG_R_CONFIG2);
-		if (reg_config2 < 0)
+		config2 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG2);
+		if (config2 < 0)
 			return -ENODEV;
 	} else
-		reg_config2 = 0;	/* Make compiler happy */
+		config2 = 0;		/* Make compiler happy */
 
 	if ((address == 0x4C || address == 0x4D)
 	 && man_id == 0x01) { /* National Semiconductor */
-		if ((reg_config1 & 0x2A) == 0x00
-		 && (reg_config2 & 0xF8) == 0x00
-		 && reg_convrate <= 0x09) {
+		if ((config1 & 0x2A) == 0x00
+		 && (config2 & 0xF8) == 0x00
+		 && convrate <= 0x09) {
 			if (address == 0x4C
 			 && (chip_id & 0xF0) == 0x20) { /* LM90 */
 				name = "lm90";
@@ -1163,8 +1159,8 @@ static int lm90_detect(struct i2c_client *new_client,
 	if ((address == 0x4C || address == 0x4D)
 	 && man_id == 0x41) { /* Analog Devices */
 		if ((chip_id & 0xF0) == 0x40 /* ADM1032 */
-		 && (reg_config1 & 0x3F) == 0x00
-		 && reg_convrate <= 0x0A) {
+		 && (config1 & 0x3F) == 0x00
+		 && convrate <= 0x0A) {
 			name = "adm1032";
 			/* The ADM1032 supports PEC, but only if combined
 			   transactions are not used. */
@@ -1173,18 +1169,18 @@ static int lm90_detect(struct i2c_client *new_client,
 				info->flags |= I2C_CLIENT_PEC;
 		} else
 		if (chip_id == 0x51 /* ADT7461 */
-		 && (reg_config1 & 0x1B) == 0x00
-		 && reg_convrate <= 0x0A) {
+		 && (config1 & 0x1B) == 0x00
+		 && convrate <= 0x0A) {
 			name = "adt7461";
 		} else
 		if (chip_id == 0x57 /* ADT7461A, NCT1008 */
-		 && (reg_config1 & 0x1B) == 0x00
-		 && reg_convrate <= 0x0A) {
+		 && (config1 & 0x1B) == 0x00
+		 && convrate <= 0x0A) {
 			name = "adt7461a";
 		}
 	} else
 	if (man_id == 0x4D) { /* Maxim */
-		int reg_emerg, reg_emerg2, reg_status2;
+		int emerg, emerg2, status2;
 
 		/*
 		 * We read MAX6659_REG_R_REMOTE_EMERG twice, and re-read
@@ -1192,13 +1188,15 @@ static int lm90_detect(struct i2c_client *new_client,
 		 * exists, both readings will reflect the same value. Otherwise,
 		 * the readings will be different.
 		 */
-		if ((reg_emerg = i2c_smbus_read_byte_data(new_client,
-						MAX6659_REG_R_REMOTE_EMERG)) < 0
-		 || i2c_smbus_read_byte_data(new_client, LM90_REG_R_MAN_ID) < 0
-		 || (reg_emerg2 = i2c_smbus_read_byte_data(new_client,
-						MAX6659_REG_R_REMOTE_EMERG)) < 0
-		 || (reg_status2 = i2c_smbus_read_byte_data(new_client,
-						MAX6696_REG_R_STATUS2)) < 0)
+		emerg = i2c_smbus_read_byte_data(client,
+						 MAX6659_REG_R_REMOTE_EMERG);
+		man_id = i2c_smbus_read_byte_data(client,
+						  LM90_REG_R_MAN_ID);
+		emerg2 = i2c_smbus_read_byte_data(client,
+						  MAX6659_REG_R_REMOTE_EMERG);
+		status2 = i2c_smbus_read_byte_data(client,
+						   MAX6696_REG_R_STATUS2);
+		if (emerg < 0 || man_id < 0 || emerg2 < 0 || status2 < 0)
 			return -ENODEV;
 
 		/*
@@ -1216,8 +1214,8 @@ static int lm90_detect(struct i2c_client *new_client,
 		 */
 		if (chip_id == man_id
 		 && (address == 0x4C || address == 0x4D || address == 0x4E)
-		 && (reg_config1 & 0x1F) == (man_id & 0x0F)
-		 && reg_convrate <= 0x09) {
+		 && (config1 & 0x1F) == (man_id & 0x0F)
+		 && convrate <= 0x09) {
 			if (address == 0x4C)
 				name = "max6657";
 			else
@@ -1235,10 +1233,10 @@ static int lm90_detect(struct i2c_client *new_client,
 		 * one of those registers exists.
 		 */
 		if (chip_id == 0x01
-		 && (reg_config1 & 0x10) == 0x00
-		 && (reg_status2 & 0x01) == 0x00
-		 && reg_emerg == reg_emerg2
-		 && reg_convrate <= 0x07) {
+		 && (config1 & 0x10) == 0x00
+		 && (status2 & 0x01) == 0x00
+		 && emerg == emerg2
+		 && convrate <= 0x07) {
 			name = "max6696";
 		} else
 		/*
@@ -1248,8 +1246,8 @@ static int lm90_detect(struct i2c_client *new_client,
 		 * second to last bit of config1 (software reset).
 		 */
 		if (chip_id == 0x01
-		 && (reg_config1 & 0x03) == 0x00
-		 && reg_convrate <= 0x07) {
+		 && (config1 & 0x03) == 0x00
+		 && convrate <= 0x07) {
 			name = "max6680";
 		} else
 		/*
@@ -1258,21 +1256,21 @@ static int lm90_detect(struct i2c_client *new_client,
 		 * register are unused and should return zero when read.
 		 */
 		if (chip_id == 0x59
-		 && (reg_config1 & 0x3f) == 0x00
-		 && reg_convrate <= 0x07) {
+		 && (config1 & 0x3f) == 0x00
+		 && convrate <= 0x07) {
 			name = "max6646";
 		}
 	} else
 	if (address == 0x4C
 	 && man_id == 0x5C) { /* Winbond/Nuvoton */
-		if ((reg_config1 & 0x2A) == 0x00
-		 && (reg_config2 & 0xF8) == 0x00) {
+		if ((config1 & 0x2A) == 0x00
+		 && (config2 & 0xF8) == 0x00) {
 			if (chip_id == 0x01 /* W83L771W/G */
-			 && reg_convrate <= 0x09) {
+			 && convrate <= 0x09) {
 				name = "w83l771";
 			} else
 			if ((chip_id & 0xFE) == 0x10 /* W83L771AWG/ASG */
-			 && reg_convrate <= 0x08) {
+			 && convrate <= 0x08) {
 				name = "w83l771";
 			}
 		}
@@ -1280,9 +1278,9 @@ static int lm90_detect(struct i2c_client *new_client,
 	if (address >= 0x48 && address <= 0x4F
 	 && man_id == 0xA1) { /*  NXP Semiconductor/Philips */
 		if (chip_id == 0x00
-		 && (reg_config1 & 0x2A) == 0x00
-		 && (reg_config2 & 0xFE) == 0x00
-		 && reg_convrate <= 0x09) {
+		 && (config1 & 0x2A) == 0x00
+		 && (config2 & 0xFE) == 0x00
+		 && convrate <= 0x09) {
 			name = "sa56004";
 		}
 	}
@@ -1301,19 +1299,18 @@ static int lm90_detect(struct i2c_client *new_client,
 
 static void lm90_remove_files(struct i2c_client *client, struct lm90_data *data)
 {
+	struct device *dev = &client->dev;
+
 	if (data->flags & LM90_HAVE_TEMP3)
-		sysfs_remove_group(&client->dev.kobj, &lm90_temp3_group);
+		sysfs_remove_group(&dev->kobj, &lm90_temp3_group);
 	if (data->flags & LM90_HAVE_EMERGENCY_ALARM)
-		sysfs_remove_group(&client->dev.kobj,
-				   &lm90_emergency_alarm_group);
+		sysfs_remove_group(&dev->kobj, &lm90_emergency_alarm_group);
 	if (data->flags & LM90_HAVE_EMERGENCY)
-		sysfs_remove_group(&client->dev.kobj,
-				   &lm90_emergency_group);
+		sysfs_remove_group(&dev->kobj, &lm90_emergency_group);
 	if (data->flags & LM90_HAVE_OFFSET)
-		device_remove_file(&client->dev,
-				   &sensor_dev_attr_temp2_offset.dev_attr);
-	device_remove_file(&client->dev, &dev_attr_pec);
-	sysfs_remove_group(&client->dev.kobj, &lm90_group);
+		device_remove_file(dev, &sensor_dev_attr_temp2_offset.dev_attr);
+	device_remove_file(dev, &dev_attr_pec);
+	sysfs_remove_group(&dev->kobj, &lm90_group);
 }
 
 static void lm90_init_client(struct i2c_client *client)
@@ -1362,10 +1359,11 @@ static void lm90_init_client(struct i2c_client *client)
 		i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, config);
 }
 
-static int lm90_probe(struct i2c_client *new_client,
+static int lm90_probe(struct i2c_client *client,
 		      const struct i2c_device_id *id)
 {
-	struct i2c_adapter *adapter = to_i2c_adapter(new_client->dev.parent);
+	struct device *dev = &client->dev;
+	struct i2c_adapter *adapter = to_i2c_adapter(dev->parent);
 	struct lm90_data *data;
 	int err;
 
@@ -1374,14 +1372,14 @@ static int lm90_probe(struct i2c_client *new_client,
 		err = -ENOMEM;
 		goto exit;
 	}
-	i2c_set_clientdata(new_client, data);
+	i2c_set_clientdata(client, data);
 	mutex_init(&data->update_lock);
 
 	/* Set the device type */
 	data->kind = id->driver_data;
 	if (data->kind == adm1032) {
 		if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
-			new_client->flags &= ~I2C_CLIENT_PEC;
+			client->flags &= ~I2C_CLIENT_PEC;
 	}
 
 	/* Different devices have different alarm bits triggering the
@@ -1396,43 +1394,41 @@ static int lm90_probe(struct i2c_client *new_client,
 	data->max_convrate = lm90_params[data->kind].max_convrate;
 
 	/* Initialize the LM90 chip */
-	lm90_init_client(new_client);
+	lm90_init_client(client);
 
 	/* Register sysfs hooks */
-	err = sysfs_create_group(&new_client->dev.kobj, &lm90_group);
+	err = sysfs_create_group(&dev->kobj, &lm90_group);
 	if (err)
 		goto exit_free;
-	if (new_client->flags & I2C_CLIENT_PEC) {
-		err = device_create_file(&new_client->dev, &dev_attr_pec);
+	if (client->flags & I2C_CLIENT_PEC) {
+		err = device_create_file(dev, &dev_attr_pec);
 		if (err)
 			goto exit_remove_files;
 	}
 	if (data->flags & LM90_HAVE_OFFSET) {
-		err = device_create_file(&new_client->dev,
+		err = device_create_file(dev,
 					&sensor_dev_attr_temp2_offset.dev_attr);
 		if (err)
 			goto exit_remove_files;
 	}
 	if (data->flags & LM90_HAVE_EMERGENCY) {
-		err = sysfs_create_group(&new_client->dev.kobj,
-					 &lm90_emergency_group);
+		err = sysfs_create_group(&dev->kobj, &lm90_emergency_group);
 		if (err)
 			goto exit_remove_files;
 	}
 	if (data->flags & LM90_HAVE_EMERGENCY_ALARM) {
-		err = sysfs_create_group(&new_client->dev.kobj,
+		err = sysfs_create_group(&dev->kobj,
 					 &lm90_emergency_alarm_group);
 		if (err)
 			goto exit_remove_files;
 	}
 	if (data->flags & LM90_HAVE_TEMP3) {
-		err = sysfs_create_group(&new_client->dev.kobj,
-					 &lm90_temp3_group);
+		err = sysfs_create_group(&dev->kobj, &lm90_temp3_group);
 		if (err)
 			goto exit_remove_files;
 	}
 
-	data->hwmon_dev = hwmon_device_register(&new_client->dev);
+	data->hwmon_dev = hwmon_device_register(dev);
 	if (IS_ERR(data->hwmon_dev)) {
 		err = PTR_ERR(data->hwmon_dev);
 		goto exit_remove_files;
@@ -1441,7 +1437,7 @@ static int lm90_probe(struct i2c_client *new_client,
 	return 0;
 
 exit_remove_files:
-	lm90_remove_files(new_client, data);
+	lm90_remove_files(client, data);
 exit_free:
 	kfree(data);
 exit:

drivers/hwmon/lm92.c

@@ -117,16 +117,16 @@ static struct lm92_data *lm92_update_device(struct device *dev)
 	if (time_after(jiffies, data->last_updated + HZ)
 	 || !data->valid) {
 		dev_dbg(&client->dev, "Updating lm92 data\n");
-		data->temp1_input = swab16(i2c_smbus_read_word_data(client,
-				    LM92_REG_TEMP));
-		data->temp1_hyst = swab16(i2c_smbus_read_word_data(client,
-				    LM92_REG_TEMP_HYST));
-		data->temp1_crit = swab16(i2c_smbus_read_word_data(client,
-				    LM92_REG_TEMP_CRIT));
-		data->temp1_min = swab16(i2c_smbus_read_word_data(client,
-				    LM92_REG_TEMP_LOW));
-		data->temp1_max = swab16(i2c_smbus_read_word_data(client,
-				    LM92_REG_TEMP_HIGH));
+		data->temp1_input = i2c_smbus_read_word_swapped(client,
+				    LM92_REG_TEMP);
+		data->temp1_hyst = i2c_smbus_read_word_swapped(client,
+				    LM92_REG_TEMP_HYST);
+		data->temp1_crit = i2c_smbus_read_word_swapped(client,
+				    LM92_REG_TEMP_CRIT);
+		data->temp1_min = i2c_smbus_read_word_swapped(client,
+				    LM92_REG_TEMP_LOW);
+		data->temp1_max = i2c_smbus_read_word_swapped(client,
+				    LM92_REG_TEMP_HIGH);
 
 		data->last_updated = jiffies;
 		data->valid = 1;
@@ -158,7 +158,7 @@ static ssize_t set_##value(struct device *dev, struct device_attribute *attr, co
  \
 	mutex_lock(&data->update_lock); \
 	data->value = TEMP_TO_REG(val); \
-	i2c_smbus_write_word_data(client, reg, swab16(data->value)); \
+	i2c_smbus_write_word_swapped(client, reg, data->value); \
 	mutex_unlock(&data->update_lock); \
 	return count; \
 }
@@ -194,8 +194,8 @@ static ssize_t set_temp1_crit_hyst(struct device *dev, struct device_attribute *
 
 	mutex_lock(&data->update_lock);
 	data->temp1_hyst = TEMP_FROM_REG(data->temp1_crit) - val;
-	i2c_smbus_write_word_data(client, LM92_REG_TEMP_HYST,
-				  swab16(TEMP_TO_REG(data->temp1_hyst)));
+	i2c_smbus_write_word_swapped(client, LM92_REG_TEMP_HYST,
+				     TEMP_TO_REG(data->temp1_hyst));
 	mutex_unlock(&data->update_lock);
 	return count;
 }

drivers/hwmon/max16065.c

@@ -137,10 +137,10 @@ static int max16065_read_adc(struct i2c_client *client, int reg)
 {
 	int rv;
 
-	rv = i2c_smbus_read_word_data(client, reg);
+	rv = i2c_smbus_read_word_swapped(client, reg);
 	if (unlikely(rv < 0))
 		return rv;
-	return ((rv & 0xff) << 2) | ((rv >> 14) & 0x03);
+	return rv >> 6;
 }
 
 static struct max16065_data *max16065_update_device(struct device *dev)

drivers/hwmon/sht21.c

@@ -82,25 +82,6 @@ static inline int sht21_rh_ticks_to_per_cent_mille(int ticks)
 	return ((15625 * ticks) >> 13) - 6000;
 }
 
-/**
- * sht21_read_word_data() - read word from register
- * @client: I2C client device
- * @reg: I2C command byte
- *
- * Returns value, negative errno on error.
- */
-static inline int sht21_read_word_data(struct i2c_client *client, u8 reg)
-{
-	int ret = i2c_smbus_read_word_data(client, reg);
-	if (ret < 0)
-		return ret;
-	/*
-	 * SMBus specifies low byte first, but the SHT21 returns MSB
-	 * first, so we have to swab16 the values
-	 */
-	return swab16(ret);
-}
-
 /**
  * sht21_update_measurements() - get updated measurements from device
  * @client: I2C client device
@@ -119,12 +100,13 @@ static int sht21_update_measurements(struct i2c_client *client)
 	 * maximum two measurements per second at 12bit accuracy shall be made.
 	 */
 	if (time_after(jiffies, sht21->last_update + HZ / 2) || !sht21->valid) {
-		ret = sht21_read_word_data(client, SHT21_TRIG_T_MEASUREMENT_HM);
+		ret = i2c_smbus_read_word_swapped(client,
+						  SHT21_TRIG_T_MEASUREMENT_HM);
 		if (ret < 0)
 			goto out;
 		sht21->temperature = sht21_temp_ticks_to_millicelsius(ret);
-		ret = sht21_read_word_data(client,
-					SHT21_TRIG_RH_MEASUREMENT_HM);
+		ret = i2c_smbus_read_word_swapped(client,
+						  SHT21_TRIG_RH_MEASUREMENT_HM);
 		if (ret < 0)
 			goto out;
 		sht21->humidity = sht21_rh_ticks_to_per_cent_mille(ret);

drivers/hwmon/smm665.c

@@ -214,33 +214,26 @@ static int smm665_read_adc(struct smm665_data *data, int adc)
 	 *
 	 * Neither i2c_smbus_read_byte() nor
 	 * i2c_smbus_read_block_data() worked here,
-	 * so use i2c_smbus_read_word_data() instead.
+	 * so use i2c_smbus_read_word_swapped() instead.
 	 * We could also try to use i2c_master_recv(),
 	 * but that is not always supported.
 	 */
-	rv = i2c_smbus_read_word_data(client, 0);
+	rv = i2c_smbus_read_word_swapped(client, 0);
 	if (rv < 0) {
 		dev_dbg(&client->dev, "Failed to read ADC value: error %d", rv);
 		return -1;
 	}
 	/*
 	 * Validate/verify readback adc channel (in bit 11..14).
-	 * High byte is in lower 8 bit of rv, so only shift by 3.
 	 */
-	radc = (rv >> 3) & 0x0f;
+	radc = (rv >> 11) & 0x0f;
 	if (radc != adc) {
 		dev_dbg(&client->dev, "Unexpected RADC: Expected %d got %d",
 			adc, radc);
 		return -EIO;
 	}
-	/*
-	 * Chip replies with H/L, while SMBus expects L/H.
-	 * Thus, byte order is reversed, and we have to swap
-	 * the result.
-	 */
-	rv = swab16(rv) & SMM665_ADC_MASK;
 
-	return rv;
+	return rv & SMM665_ADC_MASK;
 }
 
 static struct smm665_data *smm665_update_device(struct device *dev)

drivers/hwmon/smsc47b397.c

@@ -113,7 +113,7 @@ struct smsc47b397_data {
 	u8 temp[4];
 };
 
-static int smsc47b397_read_value(struct smsc47b397_data* data, u8 reg)
+static int smsc47b397_read_value(struct smsc47b397_data *data, u8 reg)
 {
 	int res;
 
@@ -265,7 +265,8 @@ static int __devinit smsc47b397_probe(struct platform_device *pdev)
 		return -EBUSY;
 	}
 
-	if (!(data = kzalloc(sizeof(struct smsc47b397_data), GFP_KERNEL))) {
+	data = kzalloc(sizeof(struct smsc47b397_data), GFP_KERNEL);
+	if (!data) {
 		err = -ENOMEM;
 		goto error_release;
 	}
@@ -276,7 +277,8 @@ static int __devinit smsc47b397_probe(struct platform_device *pdev)
 	mutex_init(&data->update_lock);
 	platform_set_drvdata(pdev, data);
 
-	if ((err = sysfs_create_group(&dev->kobj, &smsc47b397_group)))
+	err = sysfs_create_group(&dev->kobj, &smsc47b397_group);
+	if (err)
 		goto error_free;
 
 	data->hwmon_dev = hwmon_device_register(dev);
@@ -345,7 +347,7 @@ static int __init smsc47b397_find(unsigned short *addr)
 	superio_enter();
 	id = force_id ? force_id : superio_inb(SUPERIO_REG_DEVID);
 
-	switch(id) {
+	switch (id) {
 	case 0x81:
 		name = "SCH5307-NS";
 		break;
@@ -379,7 +381,8 @@ static int __init smsc47b397_init(void)
 	unsigned short address;
 	int ret;
 
-	if ((ret = smsc47b397_find(&address)))
+	ret = smsc47b397_find(&address);
+	if (ret)
 		return ret;
 
 	ret = platform_driver_register(&smsc47b397_driver);

drivers/hwmon/tmp102.c

@@ -55,19 +55,6 @@ struct tmp102 {
 	int temp[3];
 };
 
-/* SMBus specifies low byte first, but the TMP102 returns high byte first,
- * so we have to swab16 the values */
-static inline int tmp102_read_reg(struct i2c_client *client, u8 reg)
-{
-	int result = i2c_smbus_read_word_data(client, reg);
-	return result < 0 ? result : swab16(result);
-}
-
-static inline int tmp102_write_reg(struct i2c_client *client, u8 reg, u16 val)
-{
-	return i2c_smbus_write_word_data(client, reg, swab16(val));
-}
-
 /* convert left adjusted 13-bit TMP102 register value to milliCelsius */
 static inline int tmp102_reg_to_mC(s16 val)
 {
@@ -94,7 +81,8 @@ static struct tmp102 *tmp102_update_device(struct i2c_client *client)
 	if (time_after(jiffies, tmp102->last_update + HZ / 3)) {
 		int i;
 		for (i = 0; i < ARRAY_SIZE(tmp102->temp); ++i) {
-			int status = tmp102_read_reg(client, tmp102_reg[i]);
+			int status = i2c_smbus_read_word_swapped(client,
+								 tmp102_reg[i]);
 			if (status > -1)
 				tmp102->temp[i] = tmp102_reg_to_mC(status);
 		}
@@ -130,8 +118,8 @@ static ssize_t tmp102_set_temp(struct device *dev,
 
 	mutex_lock(&tmp102->lock);
 	tmp102->temp[sda->index] = val;
-	status = tmp102_write_reg(client, tmp102_reg[sda->index],
-				  tmp102_mC_to_reg(val));
+	status = i2c_smbus_write_word_swapped(client, tmp102_reg[sda->index],
+					      tmp102_mC_to_reg(val));
 	mutex_unlock(&tmp102->lock);
 	return status ? : count;
 }
@@ -178,18 +166,19 @@ static int __devinit tmp102_probe(struct i2c_client *client,
 	}
 	i2c_set_clientdata(client, tmp102);
 
-	status = tmp102_read_reg(client, TMP102_CONF_REG);
+	status = i2c_smbus_read_word_swapped(client, TMP102_CONF_REG);
 	if (status < 0) {
 		dev_err(&client->dev, "error reading config register\n");
 		goto fail_free;
 	}
 	tmp102->config_orig = status;
-	status = tmp102_write_reg(client, TMP102_CONF_REG, TMP102_CONFIG);
+	status = i2c_smbus_write_word_swapped(client, TMP102_CONF_REG,
+					      TMP102_CONFIG);
 	if (status < 0) {
 		dev_err(&client->dev, "error writing config register\n");
 		goto fail_restore_config;
 	}
-	status = tmp102_read_reg(client, TMP102_CONF_REG);
+	status = i2c_smbus_read_word_swapped(client, TMP102_CONF_REG);
 	if (status < 0) {
 		dev_err(&client->dev, "error reading config register\n");
 		goto fail_restore_config;
@@ -222,7 +211,8 @@ static int __devinit tmp102_probe(struct i2c_client *client,
 fail_remove_sysfs:
 	sysfs_remove_group(&client->dev.kobj, &tmp102_attr_group);
 fail_restore_config:
-	tmp102_write_reg(client, TMP102_CONF_REG, tmp102->config_orig);
+	i2c_smbus_write_word_swapped(client, TMP102_CONF_REG,
+				     tmp102->config_orig);
 fail_free:
 	kfree(tmp102);
 
@@ -240,10 +230,10 @@ static int __devexit tmp102_remove(struct i2c_client *client)
 	if (tmp102->config_orig & TMP102_CONF_SD) {
 		int config;
 
-		config = tmp102_read_reg(client, TMP102_CONF_REG);
+		config = i2c_smbus_read_word_swapped(client, TMP102_CONF_REG);
 		if (config >= 0)
-			tmp102_write_reg(client, TMP102_CONF_REG,
-					 config | TMP102_CONF_SD);
+			i2c_smbus_write_word_swapped(client, TMP102_CONF_REG,
+						     config | TMP102_CONF_SD);
 	}
 
 	kfree(tmp102);
@@ -257,12 +247,12 @@ static int tmp102_suspend(struct device *dev)
 	struct i2c_client *client = to_i2c_client(dev);
 	int config;
 
-	config = tmp102_read_reg(client, TMP102_CONF_REG);
+	config = i2c_smbus_read_word_swapped(client, TMP102_CONF_REG);
 	if (config < 0)
 		return config;
 
 	config |= TMP102_CONF_SD;
-	return tmp102_write_reg(client, TMP102_CONF_REG, config);
+	return i2c_smbus_write_word_swapped(client, TMP102_CONF_REG, config);
 }
 
 static int tmp102_resume(struct device *dev)
@@ -270,12 +260,12 @@ static int tmp102_resume(struct device *dev)
 	struct i2c_client *client = to_i2c_client(dev);
 	int config;
 
-	config = tmp102_read_reg(client, TMP102_CONF_REG);
+	config = i2c_smbus_read_word_swapped(client, TMP102_CONF_REG);
 	if (config < 0)
 		return config;
 
 	config &= ~TMP102_CONF_SD;
-	return tmp102_write_reg(client, TMP102_CONF_REG, config);
+	return i2c_smbus_write_word_swapped(client, TMP102_CONF_REG, config);
 }
 
 static const struct dev_pm_ops tmp102_dev_pm_ops = {

drivers/hwmon/w83627ehf.c

 /*
     w83627ehf - Driver for the hardware monitoring functionality of
 		the Winbond W83627EHF Super-I/O chip
-    Copyright (C) 2005  Jean Delvare <khali@linux-fr.org>
+    Copyright (C) 2005-2011  Jean Delvare <khali@linux-fr.org>
     Copyright (C) 2006  Yuan Mu (Winbond),
 			Rudolf Marek <r.marek@assembler.cz>
 			David Hubbard <david.c.hubbard@gmail.com>
@@ -39,6 +39,7 @@
 					       0x8860 0xa1
     w83627dhg    9      5       4       3      0xa020 0xc1    0x5ca3
     w83627dhg-p  9      5       4       3      0xb070 0xc1    0x5ca3
+    w83627uhg    8      2       2       2      0xa230 0xc1    0x5ca3
     w83667hg     9      5       3       3      0xa510 0xc1    0x5ca3
     w83667hg-b   9      5       3       4      0xb350 0xc1    0x5ca3
     nct6775f     9      4       3       9      0xb470 0xc1    0x5ca3
@@ -61,14 +62,17 @@
 #include <linux/io.h>
 #include "lm75.h"
 
-enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg, w83667hg_b, nct6775,
-	nct6776 };
+enum kinds {
+	w83627ehf, w83627dhg, w83627dhg_p, w83627uhg,
+	w83667hg, w83667hg_b, nct6775, nct6776,
+};
 
 /* used to set data->name = w83627ehf_device_names[data->sio_kind] */
 static const char * const w83627ehf_device_names[] = {
 	"w83627ehf",
 	"w83627dhg",
 	"w83627dhg",
+	"w83627uhg",
 	"w83667hg",
 	"w83667hg",
 	"nct6775",
@@ -104,6 +108,7 @@ MODULE_PARM_DESC(fan_debounce, "Enable debouncing for fan RPM signal");
 #define SIO_W83627EHG_ID	0x8860
 #define SIO_W83627DHG_ID	0xa020
 #define SIO_W83627DHG_P_ID	0xb070
+#define SIO_W83627UHG_ID	0xa230
 #define SIO_W83667HG_ID		0xa510
 #define SIO_W83667HG_B_ID	0xb350
 #define SIO_NCT6775_ID		0xb470
@@ -388,18 +393,23 @@ div_from_reg(u8 reg)
 	return 1 << reg;
 }
 
-/* Some of analog inputs have internal scaling (2x), 8mV is ADC LSB */
-
-static u8 scale_in[10] = { 8, 8, 16, 16, 8, 8, 8, 16, 16, 8 };
+/* Some of the voltage inputs have internal scaling, the tables below
+ * contain 8 (the ADC LSB in mV) * scaling factor * 100 */
+static const u16 scale_in_common[10] = {
+	800, 800, 1600, 1600, 800, 800, 800, 1600, 1600, 800
+};
+static const u16 scale_in_w83627uhg[9] = {
+	800, 800, 3328, 3424, 800, 800, 0, 3328, 3400
+};
 
-static inline long in_from_reg(u8 reg, u8 nr)
+static inline long in_from_reg(u8 reg, u8 nr, const u16 *scale_in)
 {
-	return reg * scale_in[nr];
+	return DIV_ROUND_CLOSEST(reg * scale_in[nr], 100);
 }
 
-static inline u8 in_to_reg(u32 val, u8 nr)
+static inline u8 in_to_reg(u32 val, u8 nr, const u16 *scale_in)
 {
-	return SENSORS_LIMIT(((val + (scale_in[nr] / 2)) / scale_in[nr]), 0,
+	return SENSORS_LIMIT(DIV_ROUND_CLOSEST(val * 100, scale_in[nr]), 0,
 			     255);
 }
 
@@ -430,6 +440,7 @@ struct w83627ehf_data {
 	const u16 *REG_FAN_STOP_TIME;
 	const u16 *REG_FAN_MAX_OUTPUT;
 	const u16 *REG_FAN_STEP_OUTPUT;
+	const u16 *scale_in;
 
 	unsigned int (*fan_from_reg)(u16 reg, unsigned int divreg);
 	unsigned int (*fan_from_reg_min)(u16 reg, unsigned int divreg);
@@ -481,7 +492,8 @@ struct w83627ehf_data {
 	u8 vrm;
 
 	u16 have_temp;
-	u8 in6_skip;
+	u8 in6_skip:1;
+	u8 temp3_val_only:1;
 };
 
 struct w83627ehf_sio_data {
@@ -907,7 +919,8 @@ show_##reg(struct device *dev, struct device_attribute *attr, \
 	struct sensor_device_attribute *sensor_attr = \
 		to_sensor_dev_attr(attr); \
 	int nr = sensor_attr->index; \
-	return sprintf(buf, "%ld\n", in_from_reg(data->reg[nr], nr)); \
+	return sprintf(buf, "%ld\n", in_from_reg(data->reg[nr], nr, \
+		       data->scale_in)); \
 }
 show_in_reg(in)
 show_in_reg(in_min)
@@ -928,7 +941,7 @@ store_in_##reg(struct device *dev, struct device_attribute *attr, \
 	if (err < 0) \
 		return err; \
 	mutex_lock(&data->update_lock); \
-	data->in_##reg[nr] = in_to_reg(val, nr); \
+	data->in_##reg[nr] = in_to_reg(val, nr, data->scale_in); \
 	w83627ehf_write_value(data, W83627EHF_REG_IN_##REG(nr), \
 			      data->in_##reg[nr]); \
 	mutex_unlock(&data->update_lock); \
@@ -1617,25 +1630,28 @@ static struct sensor_device_attribute sda_sf3_arrays_fan4[] = {
 		    store_fan_step_output, 3),
 };
 
+static struct sensor_device_attribute sda_sf3_arrays_fan3[] = {
+	SENSOR_ATTR(pwm3_stop_time, S_IWUSR | S_IRUGO, show_fan_stop_time,
+		    store_fan_stop_time, 2),
+	SENSOR_ATTR(pwm3_start_output, S_IWUSR | S_IRUGO, show_fan_start_output,
+		    store_fan_start_output, 2),
+	SENSOR_ATTR(pwm3_stop_output, S_IWUSR | S_IRUGO, show_fan_stop_output,
+		    store_fan_stop_output, 2),
+};
+
 static struct sensor_device_attribute sda_sf3_arrays[] = {
 	SENSOR_ATTR(pwm1_stop_time, S_IWUSR | S_IRUGO, show_fan_stop_time,
 		    store_fan_stop_time, 0),
 	SENSOR_ATTR(pwm2_stop_time, S_IWUSR | S_IRUGO, show_fan_stop_time,
 		    store_fan_stop_time, 1),
-	SENSOR_ATTR(pwm3_stop_time, S_IWUSR | S_IRUGO, show_fan_stop_time,
-		    store_fan_stop_time, 2),
 	SENSOR_ATTR(pwm1_start_output, S_IWUSR | S_IRUGO, show_fan_start_output,
 		    store_fan_start_output, 0),
 	SENSOR_ATTR(pwm2_start_output, S_IWUSR | S_IRUGO, show_fan_start_output,
 		    store_fan_start_output, 1),
-	SENSOR_ATTR(pwm3_start_output, S_IWUSR | S_IRUGO, show_fan_start_output,
-		    store_fan_start_output, 2),
 	SENSOR_ATTR(pwm1_stop_output, S_IWUSR | S_IRUGO, show_fan_stop_output,
 		    store_fan_stop_output, 0),
 	SENSOR_ATTR(pwm2_stop_output, S_IWUSR | S_IRUGO, show_fan_stop_output,
 		    store_fan_stop_output, 1),
-	SENSOR_ATTR(pwm3_stop_output, S_IWUSR | S_IRUGO, show_fan_stop_output,
-		    store_fan_stop_output, 2),
 };
 
 
@@ -1728,6 +1744,8 @@ static void w83627ehf_device_remove_files(struct device *dev)
 		    data->REG_FAN_STEP_OUTPUT[attr->index] != 0xff)
 			device_remove_file(dev, &attr->dev_attr);
 	}
+	for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan3); i++)
+		device_remove_file(dev, &sda_sf3_arrays_fan3[i].dev_attr);
 	for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan4); i++)
 		device_remove_file(dev, &sda_sf3_arrays_fan4[i].dev_attr);
 	for (i = 0; i < data->in_num; i++) {
@@ -1756,6 +1774,8 @@ static void w83627ehf_device_remove_files(struct device *dev)
 			continue;
 		device_remove_file(dev, &sda_temp_input[i].dev_attr);
 		device_remove_file(dev, &sda_temp_label[i].dev_attr);
+		if (i == 2 && data->temp3_val_only)
+			continue;
 		device_remove_file(dev, &sda_temp_max[i].dev_attr);
 		device_remove_file(dev, &sda_temp_max_hyst[i].dev_attr);
 		if (i > 2)
@@ -1808,11 +1828,21 @@ static inline void __devinit w83627ehf_init_device(struct w83627ehf_data *data,
 	case w83627ehf:
 		diode = w83627ehf_read_value(data, W83627EHF_REG_DIODE);
 		break;
+	case w83627uhg:
+		diode = 0x00;
+		break;
 	default:
 		diode = 0x70;
 	}
 	for (i = 0; i < 3; i++) {
-		if ((tmp & (0x02 << i)))
+		const char *label = data->temp_label[data->temp_src[i]];
+
+		/* Digital source overrides analog type */
+		if (strncmp(label, "PECI", 4) == 0)
+			data->temp_type[i] = 6;
+		else if (strncmp(label, "AMD", 3) == 0)
+			data->temp_type[i] = 5;
+		else if ((tmp & (0x02 << i)))
 			data->temp_type[i] = (diode & (0x10 << i)) ? 1 : 3;
 		else
 			data->temp_type[i] = 4; /* thermistor */
@@ -1845,12 +1875,32 @@ static void w82627ehf_swap_tempreg(struct w83627ehf_data *data,
 	data->reg_temp_config[r2] = tmp;
 }
 
+static void __devinit
+w83627ehf_set_temp_reg_ehf(struct w83627ehf_data *data, int n_temp)
+{
+	int i;
+
+	for (i = 0; i < n_temp; i++) {
+		data->reg_temp[i] = W83627EHF_REG_TEMP[i];
+		data->reg_temp_over[i] = W83627EHF_REG_TEMP_OVER[i];
+		data->reg_temp_hyst[i] = W83627EHF_REG_TEMP_HYST[i];
+		data->reg_temp_config[i] = W83627EHF_REG_TEMP_CONFIG[i];
+	}
+}
+
 static void __devinit
 w83627ehf_check_fan_inputs(const struct w83627ehf_sio_data *sio_data,
 			   struct w83627ehf_data *data)
 {
 	int fan3pin, fan4pin, fan4min, fan5pin, regval;
 
+	/* The W83627UHG is simple, only two fan inputs, no config */
+	if (sio_data->kind == w83627uhg) {
+		data->has_fan = 0x03; /* fan1 and fan2 */
+		data->has_fan_min = 0x03;
+		return;
+	}
+
 	superio_enter(sio_data->sioreg);
 
 	/* fan4 and fan5 share some pins with the GPIO and serial flash */
@@ -1942,23 +1992,24 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 
 	/* 627EHG and 627EHF have 10 voltage inputs; 627DHG and 667HG have 9 */
 	data->in_num = (sio_data->kind == w83627ehf) ? 10 : 9;
-	/* 667HG, NCT6775F, and NCT6776F have 3 pwms */
-	data->pwm_num = (sio_data->kind == w83667hg
-			 || sio_data->kind == w83667hg_b
-			 || sio_data->kind == nct6775
-			 || sio_data->kind == nct6776) ? 3 : 4;
+	/* 667HG, NCT6775F, and NCT6776F have 3 pwms, and 627UHG has only 2 */
+	switch (sio_data->kind) {
+	default:
+		data->pwm_num = 4;
+		break;
+	case w83667hg:
+	case w83667hg_b:
+	case nct6775:
+	case nct6776:
+		data->pwm_num = 3;
+		break;
+	case w83627uhg:
+		data->pwm_num = 2;
+		break;
+	}
 
+	/* Default to 3 temperature inputs, code below will adjust as needed */
 	data->have_temp = 0x07;
-	/* Check temp3 configuration bit for 667HG */
-	if (sio_data->kind == w83667hg) {
-		u8 reg;
-
-		reg = w83627ehf_read_value(data, W83627EHF_REG_TEMP_CONFIG[2]);
-		if (reg & 0x01)
-			data->have_temp &= ~(1 << 2);
-		else
-			data->in6_skip = 1;	/* either temp3 or in6 */
-	}
 
 	/* Deal with temperature register setup first. */
 	if (sio_data->kind == nct6775 || sio_data->kind == nct6776) {
@@ -2035,16 +2086,12 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 	} else if (sio_data->kind == w83667hg_b) {
 		u8 reg;
 
+		w83627ehf_set_temp_reg_ehf(data, 4);
+
 		/*
 		 * Temperature sources are selected with bank 0, registers 0x49
 		 * and 0x4a.
 		 */
-		for (i = 0; i < ARRAY_SIZE(W83627EHF_REG_TEMP); i++) {
-			data->reg_temp[i] = W83627EHF_REG_TEMP[i];
-			data->reg_temp_over[i] = W83627EHF_REG_TEMP_OVER[i];
-			data->reg_temp_hyst[i] = W83627EHF_REG_TEMP_HYST[i];
-			data->reg_temp_config[i] = W83627EHF_REG_TEMP_CONFIG[i];
-		}
 		reg = w83627ehf_read_value(data, 0x4a);
 		data->temp_src[0] = reg >> 5;
 		reg = w83627ehf_read_value(data, 0x49);
@@ -2077,14 +2124,61 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 		    || (data->temp_src[3] == 2 && (data->have_temp & (1 << 3))))
 			data->in6_skip = 1;
 
+		data->temp_label = w83667hg_b_temp_label;
+	} else if (sio_data->kind == w83627uhg) {
+		u8 reg;
+
+		w83627ehf_set_temp_reg_ehf(data, 3);
+
+		/*
+		 * Temperature sources for temp1 and temp2 are selected with
+		 * bank 0, registers 0x49 and 0x4a.
+		 */
+		data->temp_src[0] = 0;	/* SYSTIN */
+		reg = w83627ehf_read_value(data, 0x49) & 0x07;
+		/* Adjust to have the same mapping as other source registers */
+		if (reg == 0)
+			data->temp_src[1]++;
+		else if (reg >= 2 && reg <= 5)
+			data->temp_src[1] += 2;
+		else	/* should never happen */
+			data->have_temp &= ~(1 << 1);
+		reg = w83627ehf_read_value(data, 0x4a);
+		data->temp_src[2] = reg >> 5;
+
+		/*
+		 * Skip temp3 if source is invalid or the same as temp1
+		 * or temp2.
+		 */
+		if (data->temp_src[2] == 2 || data->temp_src[2] == 3 ||
+		    data->temp_src[2] == data->temp_src[0] ||
+		    ((data->have_temp & (1 << 1)) &&
+		     data->temp_src[2] == data->temp_src[1]))
+			data->have_temp &= ~(1 << 2);
+		else
+			data->temp3_val_only = 1;	/* No limit regs */
+
+		data->in6_skip = 1;			/* No VIN3 */
+
 		data->temp_label = w83667hg_b_temp_label;
 	} else {
+		w83627ehf_set_temp_reg_ehf(data, 3);
+
 		/* Temperature sources are fixed */
-		for (i = 0; i < 3; i++) {
-			data->reg_temp[i] = W83627EHF_REG_TEMP[i];
-			data->reg_temp_over[i] = W83627EHF_REG_TEMP_OVER[i];
-			data->reg_temp_hyst[i] = W83627EHF_REG_TEMP_HYST[i];
-			data->reg_temp_config[i] = W83627EHF_REG_TEMP_CONFIG[i];
+
+		if (sio_data->kind == w83667hg) {
+			u8 reg;
+
+			/*
+			 * Chip supports either AUXTIN or VIN3. Try to find
+			 * out which one.
+			 */
+			reg = w83627ehf_read_value(data,
+						W83627EHF_REG_TEMP_CONFIG[2]);
+			if (reg & 0x01)
+				data->have_temp &= ~(1 << 2);
+			else
+				data->in6_skip = 1;
 		}
 	}
 
@@ -2144,6 +2238,12 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 		  W83627EHF_REG_FAN_STEP_OUTPUT_COMMON;
 	}
 
+	/* Setup input voltage scaling factors */
+	if (sio_data->kind == w83627uhg)
+		data->scale_in = scale_in_w83627uhg;
+	else
+		data->scale_in = scale_in_common;
+
 	/* Initialize the chip */
 	w83627ehf_init_device(data, sio_data->kind);
 
@@ -2160,7 +2260,7 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 		err = device_create_file(dev, &dev_attr_cpu0_vid);
 		if (err)
 			goto exit_release;
-	} else {
+	} else if (sio_data->kind != w83627uhg) {
 		superio_select(sio_data->sioreg, W83627EHF_LD_HWM);
 		if (superio_inb(sio_data->sioreg, SIO_REG_VID_CTRL) & 0x80) {
 			/* Set VID input sensibility if needed. In theory the
@@ -2250,7 +2350,14 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 				goto exit_remove;
 		}
 	}
-	/* if fan4 is enabled create the sf3 files for it */
+	/* if fan3 and fan4 are enabled create the sf3 files for them */
+	if ((data->has_fan & (1 << 2)) && data->pwm_num >= 3)
+		for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan3); i++) {
+			err = device_create_file(dev,
+					&sda_sf3_arrays_fan3[i].dev_attr);
+			if (err)
+				goto exit_remove;
+		}
 	if ((data->has_fan & (1 << 3)) && data->pwm_num >= 4)
 		for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan4); i++) {
 			err = device_create_file(dev,
@@ -2318,6 +2425,8 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 			if (err)
 				goto exit_remove;
 		}
+		if (i == 2 && data->temp3_val_only)
+			continue;
 		if (data->reg_temp_over[i]) {
 			err = device_create_file(dev,
 				&sda_temp_max[i].dev_attr);
@@ -2401,6 +2510,7 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
 	static const char __initdata sio_name_W83627EHG[] = "W83627EHG";
 	static const char __initdata sio_name_W83627DHG[] = "W83627DHG";
 	static const char __initdata sio_name_W83627DHG_P[] = "W83627DHG-P";
+	static const char __initdata sio_name_W83627UHG[] = "W83627UHG";
 	static const char __initdata sio_name_W83667HG[] = "W83667HG";
 	static const char __initdata sio_name_W83667HG_B[] = "W83667HG-B";
 	static const char __initdata sio_name_NCT6775[] = "NCT6775F";
@@ -2433,6 +2543,10 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
 		sio_data->kind = w83627dhg_p;
 		sio_name = sio_name_W83627DHG_P;
 		break;
+	case SIO_W83627UHG_ID:
+		sio_data->kind = w83627uhg;
+		sio_name = sio_name_W83627UHG;
+		break;
 	case SIO_W83667HG_ID:
 		sio_data->kind = w83667hg;
 		sio_name = sio_name_W83667HG;

drivers/hwmon/w83781d.c

@@ -1245,17 +1245,17 @@ w83781d_read_value_i2c(struct w83781d_data *data, u16 reg)
 		/* convert from ISA to LM75 I2C addresses */
 		switch (reg & 0xff) {
 		case 0x50:	/* TEMP */
-			res = swab16(i2c_smbus_read_word_data(cl, 0));
+			res = i2c_smbus_read_word_swapped(cl, 0);
 			break;
 		case 0x52:	/* CONFIG */
 			res = i2c_smbus_read_byte_data(cl, 1);
 			break;
 		case 0x53:	/* HYST */
-			res = swab16(i2c_smbus_read_word_data(cl, 2));
+			res = i2c_smbus_read_word_swapped(cl, 2);
 			break;
 		case 0x55:	/* OVER */
 		default:
-			res = swab16(i2c_smbus_read_word_data(cl, 3));
+			res = i2c_smbus_read_word_swapped(cl, 3);
 			break;
 		}
 	}
@@ -1289,10 +1289,10 @@ w83781d_write_value_i2c(struct w83781d_data *data, u16 reg, u16 value)
 			i2c_smbus_write_byte_data(cl, 1, value & 0xff);
 			break;
 		case 0x53:	/* HYST */
-			i2c_smbus_write_word_data(cl, 2, swab16(value));
+			i2c_smbus_write_word_swapped(cl, 2, value);
 			break;
 		case 0x55:	/* OVER */
-			i2c_smbus_write_word_data(cl, 3, swab16(value));
+			i2c_smbus_write_word_swapped(cl, 3, value);
 			break;
 		}
 	}