提交 44cc7c9c 编写于 作者: B Ben Dooks 提交者: Russell King

[ARM] 3641/1: S3C2412: Fixup gpio register naming

Patch from Ben Dooks

The current S3C2412 has used to moving S3C24XX_
for the generic form of an register has been
moved from the S3C2410.

Fixup S3C2410_EXTINTx and S3C2410_EINFLTx to
S3C24XX_EXTINTx and S3C24XX_EXTINTx

Depends on Patch #3635/1, Patch #3640/1
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
上级 46491c94
......@@ -275,28 +275,28 @@ s3c_irqext_type(unsigned int irq, unsigned int type)
if ((irq >= IRQ_EINT0) && (irq <= IRQ_EINT3))
{
gpcon_reg = S3C2410_GPFCON;
extint_reg = S3C2410_EXTINT0;
extint_reg = S3C24XX_EXTINT0;
gpcon_offset = (irq - IRQ_EINT0) * 2;
extint_offset = (irq - IRQ_EINT0) * 4;
}
else if ((irq >= IRQ_EINT4) && (irq <= IRQ_EINT7))
{
gpcon_reg = S3C2410_GPFCON;
extint_reg = S3C2410_EXTINT0;
extint_reg = S3C24XX_EXTINT0;
gpcon_offset = (irq - (EXTINT_OFF)) * 2;
extint_offset = (irq - (EXTINT_OFF)) * 4;
}
else if ((irq >= IRQ_EINT8) && (irq <= IRQ_EINT15))
{
gpcon_reg = S3C2410_GPGCON;
extint_reg = S3C2410_EXTINT1;
extint_reg = S3C24XX_EXTINT1;
gpcon_offset = (irq - IRQ_EINT8) * 2;
extint_offset = (irq - IRQ_EINT8) * 4;
}
else if ((irq >= IRQ_EINT16) && (irq <= IRQ_EINT23))
{
gpcon_reg = S3C2410_GPGCON;
extint_reg = S3C2410_EXTINT2;
extint_reg = S3C24XX_EXTINT2;
gpcon_offset = (irq - IRQ_EINT8) * 2;
extint_offset = (irq - IRQ_EINT16) * 4;
} else
......
......@@ -35,7 +35,7 @@
int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
unsigned int config)
{
void __iomem *reg = S3C2410_EINFLT0;
void __iomem *reg = S3C24XX_EINFLT0;
unsigned long flags;
unsigned long val;
......@@ -58,10 +58,10 @@ int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
/* update filter enable */
val = __raw_readl(S3C2410_EXTINT2);
val = __raw_readl(S3C24XX_EXTINT2);
val &= ~(1 << ((pin * 4) + 3));
val |= on << ((pin * 4) + 3);
__raw_writel(val, S3C2410_EXTINT2);
__raw_writel(val, S3C24XX_EXTINT2);
local_irq_restore(flags);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册