microblaze: Remove the buggy ALLOW_EDIT_AUTO config option

This was intended to allow manual override of CPU settings copied automatically
to Kconfig.auto, however it's problematic for several reasons, but mostly:

  * If the defconfig doesn't have ALLOW_EDIT_AUTO=y, then it's impossible for
    that defconfig to iverride the values in the kernel source tree.  This leads
    to very strange errors where the kernel is compiled with the wrong CPUFLAGS.

Next patch in the series will back out the default in Kconfig.auto to baseline
settings, so a kernel built with no default values will at least boot on any
hardware, just not make use of additional CPU features.
Signed-off-by: NJohn Williams <john.williams@petalogix.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

arch/microblaze/platform/Kconfig.platform

@@ -59,25 +59,6 @@ config OPT_LIB_ASM
 	  Allows turn on optimalized library function (memcpy and memmove).
 	  Function are written in asm code.
 
-# This is still a bit broken - disabling for now JW 20070504
-config ALLOW_EDIT_AUTO
-	bool "Permit Display/edit of Kconfig.auto platform settings"
-	default n
-	help
-	  Allows the editing of auto-generated platform settings from
-	  the Kconfig.auto file. Obviously this does not change the
-	  underlying hardware, so be very careful if you go editing
-	  these settings.
-
-	  Also, if you enable this, and edit various Kconfig.auto
-	  settings, YOUR CHANGES WILL BE LOST if you then disable it
-	  again. You have been warned!
-
-	  If unsure, say no.
-
-comment "Automatic platform settings from Kconfig.auto"
-	depends on ALLOW_EDIT_AUTO
-
 if PLATFORM_GENERIC=y
 	source "arch/microblaze/platform/generic/Kconfig.auto"
 endif

arch/microblaze/platform/generic/Kconfig.auto

@@ -21,7 +21,6 @@
 
 # Definitions for MICROBLAZE0
 comment "Definitions for MICROBLAZE0"
-	depends on ALLOW_EDIT_AUTO
 
 config KERNEL_BASE_ADDR
 	hex "Physical address where Linux Kernel is"
@@ -30,33 +29,33 @@ config KERNEL_BASE_ADDR
 	  BASE Address for kernel
 
 config XILINX_MICROBLAZE0_FAMILY
-	string "Targetted FPGA family" if ALLOW_EDIT_AUTO
+	string "Targetted FPGA family"
 	default "virtex5"
 
 config XILINX_MICROBLAZE0_USE_MSR_INSTR
-	int "USE_MSR_INSTR range (0:1)" if ALLOW_EDIT_AUTO
+	int "USE_MSR_INSTR range (0:1)"
 	default 1
 
 config XILINX_MICROBLAZE0_USE_PCMP_INSTR
-	int "USE_PCMP_INSTR range (0:1)" if ALLOW_EDIT_AUTO
+	int "USE_PCMP_INSTR range (0:1)"
 	default 1
 
 config XILINX_MICROBLAZE0_USE_BARREL
-	int "USE_BARREL range (0:1)" if ALLOW_EDIT_AUTO
+	int "USE_BARREL range (0:1)"
 	default 1
 
 config XILINX_MICROBLAZE0_USE_DIV
-	int "USE_DIV range (0:1)" if ALLOW_EDIT_AUTO
+	int "USE_DIV range (0:1)"
 	default 1
 
 config XILINX_MICROBLAZE0_USE_HW_MUL
-	int "USE_HW_MUL values (0=NONE, 1=MUL32, 2=MUL64)" if ALLOW_EDIT_AUTO
+	int "USE_HW_MUL values (0=NONE, 1=MUL32, 2=MUL64)"
 	default 2
 
 config XILINX_MICROBLAZE0_USE_FPU
-	int "USE_FPU values (0=NONE, 1=BASIC, 2=EXTENDED)" if ALLOW_EDIT_AUTO
+	int "USE_FPU values (0=NONE, 1=BASIC, 2=EXTENDED)"
 	default 2
 
 config XILINX_MICROBLAZE0_HW_VER
-	string "Core version number" if ALLOW_EDIT_AUTO
+	string "Core version number"
 	default 7.10.d