be2net: Add error recovery during load for Lancer

Add error recovery during load for Lancer
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSubramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/benet/be_hw.h

@@ -44,6 +44,18 @@
 #define POST_STAGE_BE_RESET		0x3 /* Host wants to reset chip */
 #define POST_STAGE_ARMFW_RDY		0xc000	/* FW is done with POST */
 
+
+/* Lancer SLIPORT_CONTROL SLIPORT_STATUS registers */
+#define SLIPORT_STATUS_OFFSET		0x404
+#define SLIPORT_CONTROL_OFFSET		0x408
+
+#define SLIPORT_STATUS_ERR_MASK		0x80000000
+#define SLIPORT_STATUS_RN_MASK		0x01000000
+#define SLIPORT_STATUS_RDY_MASK		0x00800000
+
+
+#define SLI_PORT_CONTROL_IP_MASK	0x08000000
+
 /********* Memory BAR register ************/
 #define PCICFG_MEMBAR_CTRL_INT_CTRL_OFFSET 	0xfc
 /* Host Interrupt Enable, if set interrupts are enabled although "PCI Interrupt

drivers/net/benet/be_main.c

@@ -2901,6 +2901,54 @@ static int be_dev_family_check(struct be_adapter *adapter)
 	return 0;
 }
 
+static int lancer_wait_ready(struct be_adapter *adapter)
+{
+#define SLIPORT_READY_TIMEOUT 500
+	u32 sliport_status;
+	int status = 0, i;
+
+	for (i = 0; i < SLIPORT_READY_TIMEOUT; i++) {
+		sliport_status = ioread32(adapter->db + SLIPORT_STATUS_OFFSET);
+		if (sliport_status & SLIPORT_STATUS_RDY_MASK)
+			break;
+
+		msleep(20);
+	}
+
+	if (i == SLIPORT_READY_TIMEOUT)
+		status = -1;
+
+	return status;
+}
+
+static int lancer_test_and_set_rdy_state(struct be_adapter *adapter)
+{
+	int status;
+	u32 sliport_status, err, reset_needed;
+	status = lancer_wait_ready(adapter);
+	if (!status) {
+		sliport_status = ioread32(adapter->db + SLIPORT_STATUS_OFFSET);
+		err = sliport_status & SLIPORT_STATUS_ERR_MASK;
+		reset_needed = sliport_status & SLIPORT_STATUS_RN_MASK;
+		if (err && reset_needed) {
+			iowrite32(SLI_PORT_CONTROL_IP_MASK,
+					adapter->db + SLIPORT_CONTROL_OFFSET);
+
+			/* check adapter has corrected the error */
+			status = lancer_wait_ready(adapter);
+			sliport_status = ioread32(adapter->db +
+							SLIPORT_STATUS_OFFSET);
+			sliport_status &= (SLIPORT_STATUS_ERR_MASK |
+						SLIPORT_STATUS_RN_MASK);
+			if (status || sliport_status)
+				status = -1;
+		} else if (err || reset_needed) {
+			status = -1;
+		}
+	}
+	return status;
+}
+
 static int __devinit be_probe(struct pci_dev *pdev,
 			const struct pci_device_id *pdev_id)
 {
@@ -2950,6 +2998,14 @@ static int __devinit be_probe(struct pci_dev *pdev,
 	if (status)
 		goto free_netdev;
 
+	if (lancer_chip(adapter)) {
+		status = lancer_test_and_set_rdy_state(adapter);
+		if (status) {
+			dev_err(&pdev->dev, "Adapter in non recoverable error\n");
+			goto free_netdev;
+		}
+	}
+
 	/* sync up with fw's ready state */
 	if (be_physfn(adapter)) {
 		status = be_cmd_POST(adapter);