提交 3508ea33 编写于 作者: D Denis Kirjanov 提交者: David S. Miller

sis900: Fix the tx queue timeout issue

[  198.720048] ------------[ cut here ]------------
[  198.720108] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:255 dev_watchdog+0x229/0x240()
[  198.720118] NETDEV WATCHDOG: eth0 (sis900): transmit queue 0 timed out
[  198.720125] Modules linked in: bridge stp llc dmfe sundance 3c59x sis900 mii
[  198.720159] CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc3+ #12
[  198.720167] Hardware name: System Manufacturer System Name/TUSI-M, BIOS ASUS TUSI-M ACPI BIOS
Revision 1013 Beta 001 12/14/2001
[  198.720175]  000000ff c13fa6b9 c169ddcc c12208d6 c169ddf8 c1031e4d c1664a84 c169de24
[  198.720197]  00000000 c165f5ea 000000ff c13fa6b9 00000001 000000ff c1664a84 c169de10
[  198.720217]  c1031f13 00000009 c169de08 c1664a84 c169de24 c169de50 c13fa6b9 c165f5ea
[  198.720240] Call Trace:
[  198.720257]  [<c13fa6b9>] ? dev_watchdog+0x229/0x240
[  198.720274]  [<c12208d6>] dump_stack+0x16/0x20
[  198.720306]  [<c1031e4d>] warn_slowpath_common+0x7d/0xa0
[  198.720318]  [<c13fa6b9>] ? dev_watchdog+0x229/0x240
[  198.720330]  [<c1031f13>] warn_slowpath_fmt+0x33/0x40
[  198.720342]  [<c13fa6b9>] dev_watchdog+0x229/0x240
[  198.720357]  [<c103f158>] call_timer_fn+0x78/0x150
[  198.720369]  [<c103f0e0>] ? internal_add_timer+0x40/0x40
[  198.720381]  [<c13fa490>] ? dev_init_scheduler+0xa0/0xa0
[  198.720392]  [<c103f33f>] run_timer_softirq+0x10f/0x200
[  198.720412]  [<c103954f>] ? __do_softirq+0x6f/0x210
[  198.720424]  [<c13fa490>] ? dev_init_scheduler+0xa0/0xa0
[  198.720435]  [<c1039598>] __do_softirq+0xb8/0x210
[  198.720467]  [<c14b54d2>] ? _raw_spin_unlock+0x22/0x30
[  198.720484]  [<c1003245>] ? handle_irq+0x25/0xd0
[  198.720496]  [<c1039c0c>] irq_exit+0x9c/0xb0
[  198.720508]  [<c14bc9d7>] do_IRQ+0x47/0x94
[  198.720534]  [<c1056078>] ? hrtimer_start+0x28/0x30
[  198.720564]  [<c14bc8b1>] common_interrupt+0x31/0x38
[  198.720589]  [<c1008692>] ? default_idle+0x22/0xa0
[  198.720600]  [<c10083c7>] arch_cpu_idle+0x17/0x30
[  198.720631]  [<c106d23d>] cpu_startup_entry+0xcd/0x180
[  198.720643]  [<c14ae30a>] rest_init+0xaa/0xb0
[  198.720654]  [<c14ae260>] ? reciprocal_value+0x50/0x50
[  198.720668]  [<c17044e0>] ? repair_env_string+0x60/0x60
[  198.720679]  [<c1704bda>] start_kernel+0x29a/0x350
[  198.720690]  [<c17044e0>] ? repair_env_string+0x60/0x60
[  198.720721]  [<c1704269>] i386_start_kernel+0x39/0xa0
[  198.720729] ---[ end trace 81e0a6266f5c73a8 ]---
[  198.720740] eth0: Transmit timeout, status 00000204 00000000

timer routine checks the link status and if it's up calls
netif_carrier_on() allowing upper layer to start the tx queue
even if the auto-negotiation process is not finished.

Also remove ugly auto-negotiation check from the sis900_start_xmit()

CC: Duan Fugang <B38611@freescale.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 446266b0
......@@ -1318,7 +1318,7 @@ static void sis900_timer(unsigned long data)
if (duplex){
sis900_set_mode(sis_priv, speed, duplex);
sis630_set_eq(net_dev, sis_priv->chipset_rev);
netif_start_queue(net_dev);
netif_carrier_on(net_dev);
}
sis_priv->timer.expires = jiffies + HZ;
......@@ -1336,10 +1336,8 @@ static void sis900_timer(unsigned long data)
status = sis900_default_phy(net_dev);
mii_phy = sis_priv->mii;
if (status & MII_STAT_LINK){
if (status & MII_STAT_LINK)
sis900_check_mode(net_dev, mii_phy);
netif_carrier_on(net_dev);
}
} else {
/* Link ON -> OFF */
if (!(status & MII_STAT_LINK)){
......@@ -1612,12 +1610,6 @@ sis900_start_xmit(struct sk_buff *skb, struct net_device *net_dev)
unsigned int index_cur_tx, index_dirty_tx;
unsigned int count_dirty_tx;
/* Don't transmit data before the complete of auto-negotiation */
if(!sis_priv->autong_complete){
netif_stop_queue(net_dev);
return NETDEV_TX_BUSY;
}
spin_lock_irqsave(&sis_priv->lock, flags);
/* Calculate the next Tx descriptor entry. */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册