提交 330b6369 编写于 作者: F Frank Pavlic 提交者: Jeff Garzik

[PATCH] s390: qeth driver fixes [1/6]

[PATCH 4/9] s390: qeth driver fixes [1/6]

From: Frank Pavlic <fpavlic@de.ibm.com>
	- Drop incoming packets with vlan_tag set
          if card->vlangrp is not set.
        - use always vlan_hwaccel_rx to pass
	  vlan frames to the stack.
        - fix recovery problem. Device was recovered
	  properly but still not working.
	  netif_carrier_on call right before
          recovery start fixes it.
Signed-off-by: NFrank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
上级 f449c565
......@@ -1708,6 +1708,7 @@ qeth_check_ipa_data(struct qeth_card *card, struct qeth_cmd_buffer *iob)
"IP address reset.\n",
QETH_CARD_IFNAME(card),
card->info.chpid);
netif_carrier_on(card->dev);
qeth_schedule_recovery(card);
return NULL;
case IPA_CMD_MODCCID:
......@@ -2464,24 +2465,6 @@ qeth_rebuild_skb_fake_ll(struct qeth_card *card, struct sk_buff *skb,
qeth_rebuild_skb_fake_ll_eth(card, skb, hdr);
}
static inline void
qeth_rebuild_skb_vlan(struct qeth_card *card, struct sk_buff *skb,
struct qeth_hdr *hdr)
{
#ifdef CONFIG_QETH_VLAN
u16 *vlan_tag;
if (hdr->hdr.l3.ext_flags &
(QETH_HDR_EXT_VLAN_FRAME | QETH_HDR_EXT_INCLUDE_VLAN_TAG)) {
vlan_tag = (u16 *) skb_push(skb, VLAN_HLEN);
*vlan_tag = (hdr->hdr.l3.ext_flags & QETH_HDR_EXT_VLAN_FRAME)?
hdr->hdr.l3.vlan_id : *((u16 *)&hdr->hdr.l3.dest_addr[12]);
*(vlan_tag + 1) = skb->protocol;
skb->protocol = __constant_htons(ETH_P_8021Q);
}
#endif /* CONFIG_QETH_VLAN */
}
static inline __u16
qeth_layer2_rebuild_skb(struct qeth_card *card, struct sk_buff *skb,
struct qeth_hdr *hdr)
......@@ -2510,15 +2493,16 @@ qeth_layer2_rebuild_skb(struct qeth_card *card, struct sk_buff *skb,
return vlan_id;
}
static inline void
static inline __u16
qeth_rebuild_skb(struct qeth_card *card, struct sk_buff *skb,
struct qeth_hdr *hdr)
{
unsigned short vlan_id = 0;
#ifdef CONFIG_QETH_IPV6
if (hdr->hdr.l3.flags & QETH_HDR_PASSTHRU) {
skb->pkt_type = PACKET_HOST;
skb->protocol = qeth_type_trans(skb, card->dev);
return;
return 0;
}
#endif /* CONFIG_QETH_IPV6 */
skb->protocol = htons((hdr->hdr.l3.flags & QETH_HDR_IPV6)? ETH_P_IPV6 :
......@@ -2540,7 +2524,13 @@ qeth_rebuild_skb(struct qeth_card *card, struct sk_buff *skb,
default:
skb->pkt_type = PACKET_HOST;
}
qeth_rebuild_skb_vlan(card, skb, hdr);
if (hdr->hdr.l3.ext_flags &
(QETH_HDR_EXT_VLAN_FRAME | QETH_HDR_EXT_INCLUDE_VLAN_TAG)) {
vlan_id = (hdr->hdr.l3.ext_flags & QETH_HDR_EXT_VLAN_FRAME)?
hdr->hdr.l3.vlan_id : *((u16 *)&hdr->hdr.l3.dest_addr[12]);
}
if (card->options.fake_ll)
qeth_rebuild_skb_fake_ll(card, skb, hdr);
else
......@@ -2556,6 +2546,7 @@ qeth_rebuild_skb(struct qeth_card *card, struct sk_buff *skb,
else
skb->ip_summed = SW_CHECKSUMMING;
}
return vlan_id;
}
static inline void
......@@ -2568,6 +2559,7 @@ qeth_process_inbound_buffer(struct qeth_card *card,
int offset;
int rxrc;
__u16 vlan_tag = 0;
__u16 *vlan_addr;
/* get first element of current buffer */
element = (struct qdio_buffer_element *)&buf->buffer->element[0];
......@@ -2581,7 +2573,7 @@ qeth_process_inbound_buffer(struct qeth_card *card,
if (hdr->hdr.l2.id == QETH_HEADER_TYPE_LAYER2)
vlan_tag = qeth_layer2_rebuild_skb(card, skb, hdr);
else if (hdr->hdr.l3.id == QETH_HEADER_TYPE_LAYER3)
qeth_rebuild_skb(card, skb, hdr);
vlan_tag = qeth_rebuild_skb(card, skb, hdr);
else { /*in case of OSN*/
skb_push(skb, sizeof(struct qeth_hdr));
memcpy(skb->data, hdr, sizeof(struct qeth_hdr));
......@@ -2591,14 +2583,19 @@ qeth_process_inbound_buffer(struct qeth_card *card,
dev_kfree_skb_any(skb);
continue;
}
if (card->info.type == QETH_CARD_TYPE_OSN)
rxrc = card->osn_info.data_cb(skb);
else
#ifdef CONFIG_QETH_VLAN
if (vlan_tag)
vlan_hwaccel_rx(skb, card->vlangrp, vlan_tag);
if (card->vlangrp)
vlan_hwaccel_rx(skb, card->vlangrp, vlan_tag);
else {
dev_kfree_skb_any(skb);
continue;
}
else
#endif
if (card->info.type == QETH_CARD_TYPE_OSN)
rxrc = card->osn_info.data_cb(skb);
else
rxrc = netif_rx(skb);
card->dev->last_rx = jiffies;
card->stats.rx_packets++;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册