提交 32bf87e3 编写于 作者: A Andres Salomon 提交者: Linus Torvalds

x86: geode: MSR cleanup

This cleans up a few MSR-using drivers in the following manner:
  - Ensures MSRs are all defined in asm/geode.h, rather than in misc
    places
  - Makes the naming consistent; cs553[56] ones begin with MSR_,
    GX-specific ones start with MSR_GX_, and LX-specific ones start
    with MSR_LX_.  Also, make the names match the data sheet.
  - Use MSR names rather than numbers in source code
  - Document the fact that the LX's MSR_PADSEL has the wrong value
    in the data sheet.  That's, uh, good to note.
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Acked-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
上级 22af89aa
......@@ -63,7 +63,7 @@ static int __init mfgpt_fix(char *s)
/* The following udocumented bit resets the MFGPT timers */
val = 0xFF; dummy = 0;
wrmsr(0x5140002B, val, dummy);
wrmsr(MSR_MFGPT_SETUP, val, dummy);
return 1;
}
__setup("mfgptfix", mfgpt_fix);
......@@ -127,17 +127,17 @@ int geode_mfgpt_toggle_event(int timer, int cmp, int event, int enable)
* 6; that is, resets for 7 and 8 will be ignored. Is this
* a problem? -dilinger
*/
msr = MFGPT_NR_MSR;
msr = MSR_MFGPT_NR;
mask = 1 << (timer + 24);
break;
case MFGPT_EVENT_NMI:
msr = MFGPT_NR_MSR;
msr = MSR_MFGPT_NR;
mask = 1 << (timer + shift);
break;
case MFGPT_EVENT_IRQ:
msr = MFGPT_IRQ_MSR;
msr = MSR_MFGPT_IRQ;
mask = 1 << (timer + shift);
break;
......
......@@ -17,7 +17,6 @@ int gx_line_delta(int xres, int bpp);
extern struct geode_dc_ops gx_dc_ops;
/* MSR that tells us if a TFT or CRT is attached */
#define GLD_MSR_CONFIG 0xC0002001
#define GLD_MSR_CONFIG_DM_FP 0x40
/* Display controller registers */
......
......@@ -30,6 +30,7 @@
#include <linux/fb.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <asm/geode.h>
#include "geodefb.h"
#include "display_gx.h"
......@@ -326,7 +327,7 @@ static int __init gxfb_probe(struct pci_dev *pdev, const struct pci_device_id *i
/* Figure out if this is a TFT or CRT part */
rdmsrl(GLD_MSR_CONFIG, val);
rdmsrl(MSR_GX_GLD_MSR_CONFIG, val);
if ((val & GLD_MSR_CONFIG_DM_FP) == GLD_MSR_CONFIG_DM_FP)
par->enable_crt = 0;
......
......@@ -31,14 +31,6 @@ void lx_set_palette_reg(struct fb_info *, unsigned int, unsigned int,
/* MSRS */
#define MSR_LX_GLD_CONFIG 0x48002001
#define MSR_LX_GLCP_DOTPLL 0x4c000015
#define MSR_LX_DF_PADSEL 0x48002011
#define MSR_LX_DC_SPARE 0x80000011
#define MSR_LX_DF_GLCONFIG 0x48002001
#define MSR_LX_GLIU0_P2D_RO0 0x10000029
#define GLCP_DOTPLL_RESET (1 << 0)
#define GLCP_DOTPLL_BYPASS (1 << 15)
#define GLCP_DOTPLL_HALFPIX (1 << 24)
......
......@@ -13,6 +13,7 @@
#include <linux/fb.h>
#include <linux/uaccess.h>
#include <linux/delay.h>
#include <asm/geode.h>
#include "lxfb.h"
......@@ -101,7 +102,7 @@ static void lx_set_dotpll(u32 pllval)
u32 dotpll_lo, dotpll_hi;
int i;
rdmsr(MSR_LX_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
rdmsr(MSR_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
if ((dotpll_lo & GLCP_DOTPLL_LOCK) && (dotpll_hi == pllval))
return;
......@@ -110,7 +111,7 @@ static void lx_set_dotpll(u32 pllval)
dotpll_lo &= ~(GLCP_DOTPLL_BYPASS | GLCP_DOTPLL_HALFPIX);
dotpll_lo |= GLCP_DOTPLL_RESET;
wrmsr(MSR_LX_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
wrmsr(MSR_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
/* Wait 100us for the PLL to lock */
......@@ -119,7 +120,7 @@ static void lx_set_dotpll(u32 pllval)
/* Now, loop for the lock bit */
for (i = 0; i < 1000; i++) {
rdmsr(MSR_LX_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
rdmsr(MSR_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
if (dotpll_lo & GLCP_DOTPLL_LOCK)
break;
}
......@@ -127,7 +128,7 @@ static void lx_set_dotpll(u32 pllval)
/* Clear the reset bit */
dotpll_lo &= ~GLCP_DOTPLL_RESET;
wrmsr(MSR_LX_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
wrmsr(MSR_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
}
/* Set the clock based on the frequency specified by the current mode */
......@@ -255,7 +256,7 @@ static void lx_graphics_enable(struct fb_info *info)
msrlo = DF_DEFAULT_TFT_PAD_SEL_LOW;
msrhi = DF_DEFAULT_TFT_PAD_SEL_HIGH;
wrmsr(MSR_LX_DF_PADSEL, msrlo, msrhi);
wrmsr(MSR_LX_MSR_PADSEL, msrlo, msrhi);
}
if (par->output & OUTPUT_CRT) {
......@@ -321,7 +322,7 @@ void lx_set_mode(struct fb_info *info)
/* Set output mode */
rdmsrl(MSR_LX_DF_GLCONFIG, msrval);
rdmsrl(MSR_LX_GLD_MSR_CONFIG, msrval);
msrval &= ~DF_CONFIG_OUTPUT_MASK;
if (par->output & OUTPUT_PANEL) {
......@@ -335,7 +336,7 @@ void lx_set_mode(struct fb_info *info)
msrval |= DF_OUTPUT_CRT;
}
wrmsrl(MSR_LX_DF_GLCONFIG, msrval);
wrmsrl(MSR_LX_GLD_MSR_CONFIG, msrval);
/* Clear the various buffers */
/* FIXME: Adjust for panning here */
......@@ -383,13 +384,13 @@ void lx_set_mode(struct fb_info *info)
/* Set default watermark values */
rdmsrl(MSR_LX_DC_SPARE, msrval);
rdmsrl(MSR_LX_SPARE_MSR, msrval);
msrval &= ~(DC_SPARE_DISABLE_CFIFO_HGO | DC_SPARE_VFIFO_ARB_SELECT |
DC_SPARE_LOAD_WM_LPEN_MASK | DC_SPARE_WM_LPEN_OVRD |
DC_SPARE_DISABLE_INIT_VID_PRI | DC_SPARE_DISABLE_VFIFO_WM);
msrval |= DC_SPARE_DISABLE_VFIFO_WM | DC_SPARE_DISABLE_INIT_VID_PRI;
wrmsrl(MSR_LX_DC_SPARE, msrval);
wrmsrl(MSR_LX_SPARE_MSR, msrval);
gcfg = DC_GCFG_DFLE; /* Display fifo enable */
gcfg |= 0xB600; /* Set default priority */
......
......@@ -16,6 +16,7 @@
#include <asm/io.h>
#include <asm/delay.h>
#include <asm/msr.h>
#include <asm/geode.h>
#include "geodefb.h"
#include "video_gx.h"
......@@ -184,10 +185,10 @@ gx_configure_tft(struct fb_info *info)
/* Set up the DF pad select MSR */
rdmsrl(GX_VP_MSR_PAD_SELECT, val);
rdmsrl(MSR_GX_MSR_PADSEL, val);
val &= ~GX_VP_PAD_SELECT_MASK;
val |= GX_VP_PAD_SELECT_TFT;
wrmsrl(GX_VP_MSR_PAD_SELECT, val);
wrmsrl(MSR_GX_MSR_PADSEL, val);
/* Turn off the panel */
......
......@@ -14,7 +14,6 @@
extern struct geode_vid_ops gx_vid_ops;
/* GX Flatpanel control MSR */
#define GX_VP_MSR_PAD_SELECT 0xC0002011
#define GX_VP_PAD_SELECT_MASK 0x3FFFFFFF
#define GX_VP_PAD_SELECT_TFT 0x1FFFFFFF
......@@ -59,12 +58,10 @@ extern struct geode_vid_ops gx_vid_ops;
/* Geode GX clock control MSRs */
#define MSR_GLCP_SYS_RSTPLL 0x4c000014
# define MSR_GLCP_SYS_RSTPLL_DOTPREDIV2 (0x0000000000000002ull)
# define MSR_GLCP_SYS_RSTPLL_DOTPREMULT2 (0x0000000000000004ull)
# define MSR_GLCP_SYS_RSTPLL_DOTPOSTDIV3 (0x0000000000000008ull)
#define MSR_GLCP_DOTPLL 0x4c000015
# define MSR_GLCP_DOTPLL_DOTRESET (0x0000000000000001ull)
# define MSR_GLCP_DOTPLL_BYPASS (0x0000000000008000ull)
# define MSR_GLCP_DOTPLL_LOCK (0x0000000002000000ull)
......
......@@ -30,7 +30,11 @@ extern int geode_get_dev_base(unsigned int dev);
/* MSRS */
#define GX_GLCP_SYS_RSTPLL 0x4C000014
#define MSR_LX_GLD_MSR_CONFIG 0x48002001
#define MSR_LX_MSR_PADSEL 0x48002011 /* NOT 0x48000011; the data
* sheet has the wrong value */
#define MSR_GLCP_SYS_RSTPLL 0x4C000014
#define MSR_GLCP_DOTPLL 0x4C000015
#define MSR_LBAR_SMB 0x5140000B
#define MSR_LBAR_GPIO 0x5140000C
......@@ -45,8 +49,14 @@ extern int geode_get_dev_base(unsigned int dev);
#define MSR_PIC_ZSEL_LOW 0x51400022
#define MSR_PIC_ZSEL_HIGH 0x51400023
#define MFGPT_IRQ_MSR 0x51400028
#define MFGPT_NR_MSR 0x51400029
#define MSR_MFGPT_IRQ 0x51400028
#define MSR_MFGPT_NR 0x51400029
#define MSR_MFGPT_SETUP 0x5140002B
#define MSR_LX_SPARE_MSR 0x80000011 /* DC-specific */
#define MSR_GX_GLD_MSR_CONFIG 0xC0002001
#define MSR_GX_MSR_PADSEL 0xC0002011
/* Resource Sizes */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册