提交 28ae79f5 编写于 作者: O Olof Johansson 提交者: David S. Miller

pasemi_mac: Software-based LRO support

pasemi_mac: Software-based LRO support

Implement LRO for pasemi_mac. Pretty straightforward.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
上级 906674ab
......@@ -2572,6 +2572,7 @@ config PASEMI_MAC
tristate "PA Semi 1/10Gbit MAC"
depends on PPC64 && PCI
select PHYLIB
select INET_LRO
help
This driver supports the on-chip 1/10Gbit Ethernet controller on
PA Semi's PWRficient line of chips.
......
......@@ -32,6 +32,7 @@
#include <linux/ip.h>
#include <linux/tcp.h>
#include <net/checksum.h>
#include <linux/inet_lro.h>
#include <asm/irq.h>
#include <asm/firmware.h>
......@@ -56,9 +57,11 @@
/* Must be a power of two */
#define RX_RING_SIZE 1024
#define RX_RING_SIZE 2048
#define TX_RING_SIZE 4096
#define LRO_MAX_AGGR 64
#define DEFAULT_MSG_ENABLE \
(NETIF_MSG_DRV | \
NETIF_MSG_PROBE | \
......@@ -206,7 +209,6 @@ static int pasemi_get_mac_addr(struct pasemi_mac *mac)
return -ENOENT;
}
if (sscanf(maddr, "%hhx:%hhx:%hhx:%hhx:%hhx:%hhx", &addr[0],
&addr[1], &addr[2], &addr[3], &addr[4], &addr[5]) != 6) {
dev_warn(&pdev->dev,
......@@ -219,6 +221,37 @@ static int pasemi_get_mac_addr(struct pasemi_mac *mac)
return 0;
}
static int get_skb_hdr(struct sk_buff *skb, void **iphdr,
void **tcph, u64 *hdr_flags, void *data)
{
u64 macrx = (u64) data;
unsigned int ip_len;
struct iphdr *iph;
/* IPv4 header checksum failed */
if ((macrx & XCT_MACRX_HTY_M) != XCT_MACRX_HTY_IPV4_OK)
return -1;
/* non tcp packet */
skb_reset_network_header(skb);
iph = ip_hdr(skb);
if (iph->protocol != IPPROTO_TCP)
return -1;
ip_len = ip_hdrlen(skb);
skb_set_transport_header(skb, ip_len);
*tcph = tcp_hdr(skb);
/* check if ip header and tcp header are complete */
if (iph->tot_len < ip_len + tcp_hdrlen(skb))
return -1;
*hdr_flags = LRO_IPV4 | LRO_TCP;
*iphdr = iph;
return 0;
}
static int pasemi_mac_unmap_tx_skb(struct pasemi_mac *mac,
struct sk_buff *skb,
const dma_addr_t *dmas)
......@@ -662,7 +695,7 @@ static int pasemi_mac_clean_rx(struct pasemi_mac_rxring *rx,
skb_put(skb, len-4);
skb->protocol = eth_type_trans(skb, mac->netdev);
netif_receive_skb(skb);
lro_receive_skb(&mac->lro_mgr, skb, (void *)macrx);
next:
RX_DESC(rx, n) = 0;
......@@ -684,6 +717,8 @@ static int pasemi_mac_clean_rx(struct pasemi_mac_rxring *rx,
rx_ring(mac)->next_to_clean = n;
lro_flush_all(&mac->lro_mgr);
/* Increase is in number of 16-byte entries, and since each descriptor
* with an 8BRES takes up 3x8 bytes (padded to 4x8), increase with
* count*2.
......@@ -988,7 +1023,7 @@ static int pasemi_mac_open(struct net_device *dev)
PAS_IOB_DMA_COM_TIMEOUTCFG_TCNT(0x3ff));
write_iob_reg(PAS_IOB_DMA_RXCH_CFG(mac->rx->chan.chno),
PAS_IOB_DMA_RXCH_CFG_CNTTH(128));
PAS_IOB_DMA_RXCH_CFG_CNTTH(256));
write_iob_reg(PAS_IOB_DMA_TXCH_CFG(mac->tx->chan.chno),
PAS_IOB_DMA_TXCH_CFG_CNTTH(32));
......@@ -1368,6 +1403,16 @@ pasemi_mac_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
dev->features = NETIF_F_IP_CSUM | NETIF_F_LLTX | NETIF_F_SG |
NETIF_F_HIGHDMA;
mac->lro_mgr.max_aggr = LRO_MAX_AGGR;
mac->lro_mgr.max_desc = MAX_LRO_DESCRIPTORS;
mac->lro_mgr.lro_arr = mac->lro_desc;
mac->lro_mgr.get_skb_header = get_skb_hdr;
mac->lro_mgr.features = LRO_F_NAPI | LRO_F_EXTRACT_VLAN_ID;
mac->lro_mgr.dev = mac->netdev;
mac->lro_mgr.ip_summed = CHECKSUM_UNNECESSARY;
mac->lro_mgr.ip_summed_aggr = CHECKSUM_UNNECESSARY;
mac->dma_pdev = pci_get_device(PCI_VENDOR_ID_PASEMI, 0xa007, NULL);
if (!mac->dma_pdev) {
dev_err(&mac->pdev->dev, "Can't find DMA Controller\n");
......
......@@ -26,6 +26,8 @@
#include <linux/spinlock.h>
#include <linux/phy.h>
#define MAX_LRO_DESCRIPTORS 8
struct pasemi_mac_txring {
struct pasemi_dmachan chan; /* Must be first */
spinlock_t lock;
......@@ -64,7 +66,10 @@ struct pasemi_mac {
u8 mac_addr[6];
struct net_lro_mgr lro_mgr;
struct net_lro_desc lro_desc[MAX_LRO_DESCRIPTORS];
struct timer_list rxtimer;
unsigned int lro_max_aggr;
struct pasemi_mac_txring *tx;
struct pasemi_mac_rxring *rx;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册