提交 2661081f 编写于 作者: P Pierre Ossman

mmc_test: highmem tests

Add a couple of tests to make sure the host driver handles highmem
memory pages properly. Unfortunately there is no way to guarantee an
allocation below 4 GB in i386, so it might give you addresses that
are out of reach for the hardware (OTOH, so will any other highmem
allocation in the kernel).
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
上级 907b2cd6
......@@ -21,13 +21,17 @@
#define RESULT_UNSUP_HOST 2
#define RESULT_UNSUP_CARD 3
#define BUFFER_SIZE (PAGE_SIZE * 4)
#define BUFFER_ORDER 2
#define BUFFER_SIZE (PAGE_SIZE << BUFFER_ORDER)
struct mmc_test_card {
struct mmc_card *card;
u8 scratch[BUFFER_SIZE];
u8 *buffer;
#ifdef CONFIG_HIGHMEM
struct page *highmem;
#endif
};
/*******************************************************************/
......@@ -799,6 +803,94 @@ static int mmc_test_multi_xfersize_read(struct mmc_test_card *test)
return 0;
}
#ifdef CONFIG_HIGHMEM
static int mmc_test_write_high(struct mmc_test_card *test)
{
int ret;
struct scatterlist sg;
sg_init_table(&sg, 1);
sg_set_page(&sg, test->highmem, 512, 0);
ret = mmc_test_transfer(test, &sg, 1, 0, 1, 512, 1);
if (ret)
return ret;
return 0;
}
static int mmc_test_read_high(struct mmc_test_card *test)
{
int ret;
struct scatterlist sg;
sg_init_table(&sg, 1);
sg_set_page(&sg, test->highmem, 512, 0);
ret = mmc_test_transfer(test, &sg, 1, 0, 1, 512, 0);
if (ret)
return ret;
return 0;
}
static int mmc_test_multi_write_high(struct mmc_test_card *test)
{
int ret;
unsigned int size;
struct scatterlist sg;
if (test->card->host->max_blk_count == 1)
return RESULT_UNSUP_HOST;
size = PAGE_SIZE * 2;
size = min(size, test->card->host->max_req_size);
size = min(size, test->card->host->max_seg_size);
size = min(size, test->card->host->max_blk_count * 512);
if (size < 1024)
return RESULT_UNSUP_HOST;
sg_init_table(&sg, 1);
sg_set_page(&sg, test->highmem, size, 0);
ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 1);
if (ret)
return ret;
return 0;
}
static int mmc_test_multi_read_high(struct mmc_test_card *test)
{
int ret;
unsigned int size;
struct scatterlist sg;
if (test->card->host->max_blk_count == 1)
return RESULT_UNSUP_HOST;
size = PAGE_SIZE * 2;
size = min(size, test->card->host->max_req_size);
size = min(size, test->card->host->max_seg_size);
size = min(size, test->card->host->max_blk_count * 512);
if (size < 1024)
return RESULT_UNSUP_HOST;
sg_init_table(&sg, 1);
sg_set_page(&sg, test->highmem, size, 0);
ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 0);
if (ret)
return ret;
return 0;
}
#endif /* CONFIG_HIGHMEM */
static const struct mmc_test_case mmc_test_cases[] = {
{
.name = "Basic write (no data verification)",
......@@ -913,6 +1005,39 @@ static const struct mmc_test_case mmc_test_cases[] = {
.name = "Correct xfer_size at read (midway failure)",
.run = mmc_test_multi_xfersize_read,
},
#ifdef CONFIG_HIGHMEM
{
.name = "Highmem write",
.prepare = mmc_test_prepare_write,
.run = mmc_test_write_high,
.cleanup = mmc_test_cleanup,
},
{
.name = "Highmem read",
.prepare = mmc_test_prepare_read,
.run = mmc_test_read_high,
.cleanup = mmc_test_cleanup,
},
{
.name = "Multi-block highmem write",
.prepare = mmc_test_prepare_write,
.run = mmc_test_multi_write_high,
.cleanup = mmc_test_cleanup,
},
{
.name = "Multi-block highmem read",
.prepare = mmc_test_prepare_read,
.run = mmc_test_multi_read_high,
.cleanup = mmc_test_cleanup,
},
#endif /* CONFIG_HIGHMEM */
};
static struct mutex mmc_test_lock;
......@@ -1014,12 +1139,23 @@ static ssize_t mmc_test_store(struct device *dev,
test->card = card;
test->buffer = kzalloc(BUFFER_SIZE, GFP_KERNEL);
#ifdef CONFIG_HIGHMEM
test->highmem = alloc_pages(GFP_KERNEL | __GFP_HIGHMEM, BUFFER_ORDER);
#endif
#ifdef CONFIG_HIGHMEM
if (test->buffer && test->highmem) {
#else
if (test->buffer) {
#endif
mutex_lock(&mmc_test_lock);
mmc_test_run(test, testcase);
mutex_unlock(&mmc_test_lock);
}
#ifdef CONFIG_HIGHMEM
__free_pages(test->highmem, BUFFER_ORDER);
#endif
kfree(test->buffer);
kfree(test);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册