提交 257ddbda 编写于 作者: A Alexey Dobriyan 提交者: David S. Miller

netdev: remove HAVE_ leftovers

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 b50c2ea7
......@@ -7668,7 +7668,7 @@ bnx2_change_mtu(struct net_device *dev, int new_mtu)
return (bnx2_change_ring_size(bp, bp->rx_ring_size, bp->tx_ring_size));
}
#if defined(HAVE_POLL_CONTROLLER) || defined(CONFIG_NET_POLL_CONTROLLER)
#ifdef CONFIG_NET_POLL_CONTROLLER
static void
poll_bnx2(struct net_device *dev)
{
......@@ -8280,7 +8280,7 @@ static const struct net_device_ops bnx2_netdev_ops = {
#ifdef BCM_VLAN
.ndo_vlan_rx_register = bnx2_vlan_rx_register,
#endif
#if defined(HAVE_POLL_CONTROLLER) || defined(CONFIG_NET_POLL_CONTROLLER)
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = poll_bnx2,
#endif
};
......
......@@ -11731,7 +11731,7 @@ static void bnx2x_vlan_rx_register(struct net_device *dev,
#endif
#if defined(HAVE_POLL_CONTROLLER) || defined(CONFIG_NET_POLL_CONTROLLER)
#ifdef CONFIG_NET_POLL_CONTROLLER
static void poll_bnx2x(struct net_device *dev)
{
struct bnx2x *bp = netdev_priv(dev);
......@@ -11755,7 +11755,7 @@ static const struct net_device_ops bnx2x_netdev_ops = {
#ifdef BCM_VLAN
.ndo_vlan_rx_register = bnx2x_vlan_rx_register,
#endif
#if defined(HAVE_POLL_CONTROLLER) || defined(CONFIG_NET_POLL_CONTROLLER)
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = poll_bnx2x,
#endif
};
......
......@@ -106,7 +106,7 @@
#define cas_page_unmap(x) kunmap_atomic((x), KM_SKB_DATA_SOFTIRQ)
#define CAS_NCPUS num_online_cpus()
#if defined(CONFIG_CASSINI_NAPI) && defined(HAVE_NETDEV_POLL)
#ifdef CONFIG_CASSINI_NAPI
#define USE_NAPI
#define cas_skb_release(x) netif_receive_skb(x)
#else
......
......@@ -3262,7 +3262,6 @@ static void ixgbevf_shutdown(struct pci_dev *pdev)
pci_disable_device(pdev);
}
#ifdef HAVE_NET_DEVICE_OPS
static const struct net_device_ops ixgbe_netdev_ops = {
.ndo_open = &ixgbevf_open,
.ndo_stop = &ixgbevf_close,
......@@ -3278,29 +3277,12 @@ static const struct net_device_ops ixgbe_netdev_ops = {
.ndo_vlan_rx_add_vid = &ixgbevf_vlan_rx_add_vid,
.ndo_vlan_rx_kill_vid = &ixgbevf_vlan_rx_kill_vid,
};
#endif /* HAVE_NET_DEVICE_OPS */
static void ixgbevf_assign_netdev_ops(struct net_device *dev)
{
struct ixgbevf_adapter *adapter;
adapter = netdev_priv(dev);
#ifdef HAVE_NET_DEVICE_OPS
dev->netdev_ops = &ixgbe_netdev_ops;
#else /* HAVE_NET_DEVICE_OPS */
dev->open = &ixgbevf_open;
dev->stop = &ixgbevf_close;
dev->hard_start_xmit = &ixgbevf_xmit_frame;
dev->get_stats = &ixgbevf_get_stats;
dev->set_multicast_list = &ixgbevf_set_rx_mode;
dev->set_mac_address = &ixgbevf_set_mac;
dev->change_mtu = &ixgbevf_change_mtu;
dev->tx_timeout = &ixgbevf_tx_timeout;
dev->vlan_rx_register = &ixgbevf_vlan_rx_register;
dev->vlan_rx_add_vid = &ixgbevf_vlan_rx_add_vid;
dev->vlan_rx_kill_vid = &ixgbevf_vlan_rx_kill_vid;
#endif /* HAVE_NET_DEVICE_OPS */
ixgbevf_set_ethtool_ops(dev);
dev->watchdog_timeo = 5 * HZ;
}
......
......@@ -51,14 +51,11 @@
static const char *meth_str="SGI O2 Fast Ethernet";
#define HAVE_TX_TIMEOUT
/* The maximum time waited (in jiffies) before assuming a Tx failed. (400ms) */
#define TX_TIMEOUT (400*HZ/1000)
#ifdef HAVE_TX_TIMEOUT
static int timeout = TX_TIMEOUT;
module_param(timeout, int, 0);
#endif
/*
* This structure is private to each device. It is used to pass
......
......@@ -1194,9 +1194,7 @@ static const struct net_device_ops wl_netdev_ops =
.ndo_stop = &wl_adapter_close,
.ndo_do_ioctl = &wl_ioctl,
#ifdef HAVE_TX_TIMEOUT
.ndo_tx_timeout = &wl_tx_timeout,
#endif
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = wl_poll,
......@@ -1270,9 +1268,7 @@ struct net_device * wl_device_alloc( void )
dev->stop = &wl_adapter_close;
dev->do_ioctl = &wl_ioctl;
#ifdef HAVE_TX_TIMEOUT
dev->tx_timeout = &wl_tx_timeout;
#endif
#ifdef CONFIG_NET_POLL_CONTROLLER
dev->poll_controller = wl_poll;
......@@ -1280,9 +1276,7 @@ struct net_device * wl_device_alloc( void )
#endif // (LINUX_VERSION_CODE > KERNEL_VERSION(2,6,30))
#ifdef HAVE_TX_TIMEOUT
dev->watchdog_timeo = TX_TIMEOUT;
#endif
dev->ethtool_ops = &wl_ethtool_ops;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册