提交 24e6458d 编写于 作者: S Sergei Shtylyov 提交者: Bartlomiej Zolnierkiewicz

slc90e66: carry over fixes from piix driver

Synchronize with version 0.46 of the Intel PIIX/ICH driver:

- carry over Alan's and my own fixes in the tuneproc() method and my cleanups
  both there and in the ratemask() method;

- SLC90E66 only supports MW DMA modes 1/2 and SW DMA mode 2 (just like Intel
  chips), so don't claim support for other MW/SW DMA modes;

- don't check dor non-NULL drive->id in the ide_dma_check() method -- this is
  assumed to be true in all other drivers;

- do some coding/formatting cleanups while at it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
上级 30dfd12f
/*
* linux/drivers/ide/pci/slc90e66.c Version 0.12 May 12, 2006
* linux/drivers/ide/pci/slc90e66.c Version 0.13 December 30, 2006
*
* Copyright (C) 2000-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2006 MontaVista Software, Inc. <source@mvista.com>
......@@ -26,7 +26,7 @@ static u8 slc90e66_ratemask (ide_drive_t *drive)
u8 mode = 2;
if (!eighty_ninty_three(drive))
mode = min(mode, (u8)1);
mode = min_t(u8, mode, 1);
return mode;
}
......@@ -65,36 +65,47 @@ static void slc90e66_tune_drive (ide_drive_t *drive, u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
int is_slave = (&hwif->drives[1] == drive);
int is_slave = drive->dn & 1;
int master_port = hwif->channel ? 0x42 : 0x40;
int slave_port = 0x44;
unsigned long flags;
u16 master_data;
u8 slave_data;
/* ISP RTC */
int control = 0;
/* ISP RTC */
static const u8 timings[][2]= {
{ 0, 0 },
{ 0, 0 },
{ 1, 0 },
{ 2, 1 },
{ 2, 3 }, };
{ 0, 0 },
{ 0, 0 },
{ 1, 0 },
{ 2, 1 },
{ 2, 3 }, };
pio = ide_get_best_pio_mode(drive, pio, 5, NULL);
pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
spin_lock_irqsave(&ide_lock, flags);
pci_read_config_word(dev, master_port, &master_data);
if (pio > 1)
control |= 1; /* Programmable timing on */
if (drive->media == ide_disk)
control |= 4; /* Prefetch, post write */
if (pio > 2)
control |= 2; /* IORDY */
if (is_slave) {
master_data = master_data | 0x4000;
if (pio > 1)
master_data |= 0x4000;
master_data &= ~0x0070;
if (pio > 1) {
/* enable PPE, IE and TIME */
master_data = master_data | 0x0070;
master_data = master_data | (control << 4);
}
pci_read_config_byte(dev, slave_port, &slave_data);
slave_data = slave_data & (hwif->channel ? 0x0f : 0xf0);
slave_data = slave_data | (((timings[pio][0] << 2) | timings[pio][1]) << (hwif->channel ? 4 : 0));
} else {
master_data = master_data & 0xccf8;
if (pio > 1)
master_data &= ~0x3307;
if (pio > 1) {
/* enable PPE, IE and TIME */
master_data = master_data | 0x0007;
master_data = master_data | control;
}
master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8);
}
pci_write_config_word(dev, master_port, master_data);
......@@ -173,7 +184,7 @@ static int slc90e66_config_drive_xfer_rate (ide_drive_t *drive)
drive->init_speed = 0;
if (id && (id->capability & 1) && drive->autodma) {
if ((id->capability & 1) && drive->autodma) {
if (ide_use_dma(drive) && slc90e66_config_drive_for_dma(drive))
return hwif->ide_dma_on(drive);
......@@ -201,7 +212,7 @@ static void __devinit init_hwif_slc90e66 (ide_hwif_t *hwif)
hwif->irq = hwif->channel ? 15 : 14;
hwif->speedproc = &slc90e66_tune_chipset;
hwif->tuneproc = &slc90e66_tune_drive;
hwif->tuneproc = &slc90e66_tune_drive;
pci_read_config_byte(hwif->pci_dev, 0x47, &reg47);
......@@ -213,14 +224,16 @@ static void __devinit init_hwif_slc90e66 (ide_hwif_t *hwif)
hwif->atapi_dma = 1;
hwif->ultra_mask = 0x1f;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
hwif->mwdma_mask = 0x06;
hwif->swdma_mask = 0x04;
if (!(hwif->udma_four))
if (!hwif->udma_four) {
/* bit[0(1)]: 0:80, 1:40 */
hwif->udma_four = (reg47 & mask) ? 0 : 1;
}
hwif->ide_dma_check = &slc90e66_config_drive_xfer_rate;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册