提交 1f3c8804 编写于 作者: A Andy Gospodarek 提交者: David S. Miller

bonding: allow arp_ip_targets on separate vlans to use arp validation

This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation.  A configuration like this, now works:

BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever

Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1

Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30

Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 3a999e6e
......@@ -2615,6 +2615,17 @@ static int bond_arp_rcv(struct sk_buff *skb, struct net_device *dev, struct pack
unsigned char *arp_ptr;
__be32 sip, tip;
if (dev->priv_flags & IFF_802_1Q_VLAN) {
/*
* When using VLANS and bonding, dev and oriv_dev may be
* incorrect if the physical interface supports VLAN
* acceleration. With this change ARP validation now
* works for hosts only reachable on the VLAN interface.
*/
dev = vlan_dev_real_dev(dev);
orig_dev = dev_get_by_index_rcu(dev_net(skb->dev),skb->skb_iif);
}
if (!(dev->priv_flags & IFF_BONDING) || !(dev->flags & IFF_MASTER))
goto out;
......
......@@ -14,6 +14,7 @@ int __vlan_hwaccel_rx(struct sk_buff *skb, struct vlan_group *grp,
if (skb_bond_should_drop(skb))
goto drop;
skb->skb_iif = skb->dev->ifindex;
__vlan_hwaccel_put_tag(skb, vlan_tci);
skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK);
......@@ -85,6 +86,7 @@ vlan_gro_common(struct napi_struct *napi, struct vlan_group *grp,
if (skb_bond_should_drop(skb))
goto drop;
skb->skb_iif = skb->dev->ifindex;
__vlan_hwaccel_put_tag(skb, vlan_tci);
skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK);
......
......@@ -2495,12 +2495,26 @@ int netif_receive_skb(struct sk_buff *skb)
if (!skb)
goto out;
/*
* Make sure frames received on VLAN interfaces stacked on
* bonding interfaces still make their way to any base bonding
* device that may have registered for a specific ptype. The
* handler may have to adjust skb->dev and orig_dev.
*
* null_or_orig can be overloaded since it will not be set when
* using VLANs on top of bonding. Putting it here prevents
* disturbing the ptype_all handlers above.
*/
if ((skb->dev->priv_flags & IFF_802_1Q_VLAN) &&
(vlan_dev_real_dev(skb->dev)->priv_flags & IFF_BONDING)) {
null_or_orig = vlan_dev_real_dev(skb->dev);
}
type = skb->protocol;
list_for_each_entry_rcu(ptype,
&ptype_base[ntohs(type) & PTYPE_HASH_MASK], list) {
if (ptype->type == type &&
(ptype->dev == null_or_orig || ptype->dev == skb->dev ||
ptype->dev == orig_dev)) {
if (ptype->type == type && (ptype->dev == null_or_orig ||
ptype->dev == skb->dev || ptype->dev == orig_dev)) {
if (pt_prev)
ret = deliver_skb(skb, pt_prev, orig_dev);
pt_prev = ptype;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册