drivers/net: delete old DEC depca ISA drivers support.

These are old ISA 10Mbit cards from the 1st 1/2 of the 1990s and
required manual jumper settings in order to configure them.  Here
we remove them on the premise that they are no longer used in any
modern 3.9+ kernels.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Documentation/networking/00-INDEX

@@ -52,8 +52,6 @@ de4x5.txt
 	- the Digital EtherWORKS DE4?? and DE5?? PCI Ethernet driver
 decnet.txt
 	- info on using the DECnet networking layer in Linux.
-depca.txt
-	- the Digital DEPCA/EtherWORKS DE1?? and DE2?? LANCE Ethernet driver
 dl2k.txt
 	- README for D-Link DL2000-based Gigabit Ethernet Adapters (dl2k.ko).
 dm9000.txt

Documentation/networking/depca.txt

-
-DE10x
-=====
-
-Memory Addresses:
-
-	SW1	SW2	SW3	SW4
-64K	on	on	on	on	d0000	dbfff
-	off	on	on	on	c0000	cbfff
-	off	off	on	on	e0000	ebfff
-
-32K	on	on	off	on	d8000	dbfff
-	off	on	off	on	c8000	cbfff
-	off	off	off	on	e8000	ebfff
-
-DBR ROM	on	on			dc000	dffff
-	off	on			cc000	cffff
-	off	off			ec000	effff
-
-Note  that the 2K  mode   is set  by   SW3/SW4  on/off or  off/off.  Address
-assignment is through the RBSA register.
-
-I/O Address:
-	SW5
-0x300	on
-0x200	off
-
-Remote Boot:
-	SW6
-Disable	on
-Enable	off
-
-Remote Boot Timeout:
-	SW7
-2.5min	on
-30s	off
-
-IRQ:
-	SW8	SW9	SW10	SW11	SW12
-2	on	off	off	off	off
-3	off	on	off	off	off
-4	off	off	on	off	off
-5	off	off	off	on	off
-7	off	off	off	off	on
-
-DE20x
-=====
-
-Memory Size:
-
-	SW3	SW4
-64K	on	on
-32K	off	on
-2K	on 	off
-2K	off	off
-
-Start Addresses:
-
-	SW1	SW2	SW3	SW4
-64K	on	on	on	on	c0000	cffff
-	on	off	on	on	d0000	dffff
-	off	on	on	on	e0000	effff
-
-32K	on	on	off	off	c8000	cffff
-	on	off	off	off	d8000	dffff
-	off	on	off	off	e8000	effff
-
-Illegal	off	off	 -	 -	  -	  -
-
-I/O Address:
-	SW5
-0x300	on
-0x200	off
-
-Remote Boot:
-	SW6
-Disable	on
-Enable	off
-
-Remote Boot Timeout:
-	SW7
-2.5min	on
-30s	off
-
-IRQ:
-	SW8	SW9	SW10	SW11	SW12
-5	on	off	off	off	off
-9	off	on	off	off	off
-10	off	off	on	off	off
-11	off	off	off	on	off
-15	off	off	off	off	on
-

drivers/net/ethernet/amd/Kconfig

@@ -105,19 +105,6 @@ config DECLANCE
 	  DEC (now Compaq) based on the AMD LANCE chipset, including the
 	  DEPCA series.  (This chipset is better known via the NE2100 cards.)
 
-config DEPCA
-	tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
-	depends on (ISA || EISA)
-	select CRC32
-	---help---
-	  If you have a network (Ethernet) card of this type, say Y and read
-	  the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto> as well as
-	  <file:drivers/net/ethernet/amd/depca.c>.
-
-	  To compile this driver as a module, choose M here. The module
-	  will be called depca.
-
 config HPLANCE
 	bool "HP on-board LANCE support"
 	depends on DIO

drivers/net/ethernet/amd/Makefile

@@ -8,7 +8,6 @@ obj-$(CONFIG_ARM_AM79C961A) += am79c961a.o
 obj-$(CONFIG_ARIADNE) += ariadne.o
 obj-$(CONFIG_ATARILANCE) += atarilance.o
 obj-$(CONFIG_DECLANCE) += declance.o
-obj-$(CONFIG_DEPCA) += depca.o
 obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
 obj-$(CONFIG_LANCE) += lance.o
 obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o

drivers/net/ethernet/amd/depca.h

-/*
-    Written 1994 by David C. Davies.
-
-    Copyright 1994 David C. Davies. This software may be used and distributed
-    according to the terms of the GNU General Public License, incorporated herein by
-    reference.
-*/
-
-/*
-** I/O addresses. Note that the 2k buffer option is not supported in
-** this driver.
-*/
-#define DEPCA_NICSR ioaddr+0x00   /* Network interface CSR */
-#define DEPCA_RBI   ioaddr+0x02   /* RAM buffer index (2k buffer mode) */
-#define DEPCA_DATA  ioaddr+0x04   /* LANCE registers' data port */
-#define DEPCA_ADDR  ioaddr+0x06   /* LANCE registers' address port */
-#define DEPCA_HBASE ioaddr+0x08   /* EISA high memory base address reg. */
-#define DEPCA_PROM  ioaddr+0x0c   /* Ethernet address ROM data port */
-#define DEPCA_CNFG  ioaddr+0x0c   /* EISA Configuration port */
-#define DEPCA_RBSA  ioaddr+0x0e   /* RAM buffer starting address (2k buff.) */
-
-/*
-** These are LANCE registers addressable through DEPCA_ADDR
-*/
-#define CSR0       0
-#define CSR1       1
-#define CSR2       2
-#define CSR3       3
-
-/*
-** NETWORK INTERFACE CSR (NI_CSR) bit definitions
-*/
-
-#define TO       	0x0100	/* Time Out for remote boot */
-#define SHE      	0x0080  /* SHadow memory Enable */
-#define BS       	0x0040  /* Bank Select */
-#define BUF      	0x0020	/* BUFfer size (1->32k, 0->64k) */
-#define RBE      	0x0010	/* Remote Boot Enable (1->net boot) */
-#define AAC      	0x0008  /* Address ROM Address Counter (1->enable) */
-#define _128KB      	0x0008  /* 128kB Network RAM (1->enable) */
-#define IM       	0x0004	/* Interrupt Mask (1->mask) */
-#define IEN      	0x0002	/* Interrupt tristate ENable (1->enable) */
-#define LED      	0x0001	/* LED control */
-
-/*
-** Control and Status Register 0 (CSR0) bit definitions
-*/
-
-#define ERR     	0x8000 	/* Error summary */
-#define BABL    	0x4000 	/* Babble transmitter timeout error  */
-#define CERR    	0x2000 	/* Collision Error */
-#define MISS    	0x1000 	/* Missed packet */
-#define MERR    	0x0800 	/* Memory Error */
-#define RINT    	0x0400 	/* Receiver Interrupt */
-#define TINT    	0x0200 	/* Transmit Interrupt */
-#define IDON    	0x0100 	/* Initialization Done */
-#define INTR    	0x0080 	/* Interrupt Flag */
-#define INEA    	0x0040 	/* Interrupt Enable */
-#define RXON    	0x0020 	/* Receiver on */
-#define TXON    	0x0010 	/* Transmitter on */
-#define TDMD    	0x0008 	/* Transmit Demand */
-#define STOP    	0x0004 	/* Stop */
-#define STRT    	0x0002 	/* Start */
-#define INIT    	0x0001 	/* Initialize */
-#define INTM            0xff00  /* Interrupt Mask */
-#define INTE            0xfff0  /* Interrupt Enable */
-
-/*
-** CONTROL AND STATUS REGISTER 3 (CSR3)
-*/
-
-#define BSWP    	0x0004	/* Byte SWaP */
-#define ACON    	0x0002	/* ALE control */
-#define BCON    	0x0001	/* Byte CONtrol */
-
-/*
-** Initialization Block Mode Register
-*/
-
-#define PROM       	0x8000 	/* Promiscuous Mode */
-#define EMBA       	0x0080	/* Enable Modified Back-off Algorithm */
-#define INTL       	0x0040 	/* Internal Loopback */
-#define DRTY       	0x0020 	/* Disable Retry */
-#define COLL       	0x0010 	/* Force Collision */
-#define DTCR       	0x0008 	/* Disable Transmit CRC */
-#define LOOP       	0x0004 	/* Loopback */
-#define DTX        	0x0002 	/* Disable the Transmitter */
-#define DRX        	0x0001 	/* Disable the Receiver */
-
-/*
-** Receive Message Descriptor 1 (RMD1) bit definitions.
-*/
-
-#define R_OWN       0x80000000 	/* Owner bit 0 = host, 1 = lance */
-#define R_ERR     	0x4000 	/* Error Summary */
-#define R_FRAM    	0x2000 	/* Framing Error */
-#define R_OFLO    	0x1000 	/* Overflow Error */
-#define R_CRC     	0x0800 	/* CRC Error */
-#define R_BUFF    	0x0400 	/* Buffer Error */
-#define R_STP     	0x0200 	/* Start of Packet */
-#define R_ENP     	0x0100 	/* End of Packet */
-
-/*
-** Transmit Message Descriptor 1 (TMD1) bit definitions.
-*/
-
-#define T_OWN       0x80000000 	/* Owner bit 0 = host, 1 = lance */
-#define T_ERR     	0x4000 	/* Error Summary */
-#define T_ADD_FCS 	0x2000 	/* More the 1 retry needed to Xmit */
-#define T_MORE    	0x1000	/* >1 retry to transmit packet */
-#define T_ONE     	0x0800 	/* 1 try needed to transmit the packet */
-#define T_DEF     	0x0400 	/* Deferred */
-#define T_STP       0x02000000 	/* Start of Packet */
-#define T_ENP       0x01000000	/* End of Packet */
-#define T_FLAGS     0xff000000  /* TX Flags Field */
-
-/*
-** Transmit Message Descriptor 3 (TMD3) bit definitions.
-*/
-
-#define TMD3_BUFF    0x8000	/* BUFFer error */
-#define TMD3_UFLO    0x4000	/* UnderFLOw error */
-#define TMD3_RES     0x2000	/* REServed */
-#define TMD3_LCOL    0x1000	/* Late COLlision */
-#define TMD3_LCAR    0x0800	/* Loss of CARrier */
-#define TMD3_RTRY    0x0400	/* ReTRY error */
-
-/*
-** EISA configuration Register (CNFG) bit definitions
-*/
-
-#define TIMEOUT       	0x0100	/* 0:2.5 mins, 1: 30 secs */
-#define REMOTE      	0x0080  /* Remote Boot Enable -> 1 */
-#define IRQ11       	0x0040  /* Enable -> 1 */
-#define IRQ10    	0x0020	/* Enable -> 1 */
-#define IRQ9    	0x0010	/* Enable -> 1 */
-#define IRQ5      	0x0008  /* Enable -> 1 */
-#define BUFF     	0x0004	/* 0: 64kB or 128kB, 1: 32kB */
-#define PADR16   	0x0002	/* RAM on 64kB boundary */
-#define PADR17    	0x0001	/* RAM on 128kB boundary */
-
-/*
-** Miscellaneous
-*/
-#define HASH_TABLE_LEN   64           /* Bits */
-#define HASH_BITS        0x003f       /* 6 LS bits */
-
-#define MASK_INTERRUPTS   1
-#define UNMASK_INTERRUPTS 0
-
-#define EISA_EN         0x0001        /* Enable EISA bus buffers */
-#define EISA_ID         iobase+0x0080 /* ID long word for EISA card */
-#define EISA_CTRL       iobase+0x0084 /* Control word for EISA card */
-
-/*
-** Include the IOCTL stuff
-*/
-#include <linux/sockios.h>
-
-struct depca_ioctl {
-	unsigned short cmd;                /* Command to run */
-	unsigned short len;                /* Length of the data buffer */
-	unsigned char  __user *data;       /* Pointer to the data buffer */
-};
-
-/*
-** Recognised commands for the driver
-*/
-#define DEPCA_GET_HWADDR	0x01 /* Get the hardware address */
-#define DEPCA_SET_HWADDR	0x02 /* Get the hardware address */
-#define DEPCA_SET_PROM  	0x03 /* Set Promiscuous Mode */
-#define DEPCA_CLR_PROM  	0x04 /* Clear Promiscuous Mode */
-#define DEPCA_SAY_BOO	        0x05 /* Say "Boo!" to the kernel log file */
-#define DEPCA_GET_MCA   	0x06 /* Get a multicast address */
-#define DEPCA_SET_MCA   	0x07 /* Set a multicast address */
-#define DEPCA_CLR_MCA    	0x08 /* Clear a multicast address */
-#define DEPCA_MCA_EN    	0x09 /* Enable a multicast address group */
-#define DEPCA_GET_STATS  	0x0a /* Get the driver statistics */
-#define DEPCA_CLR_STATS 	0x0b /* Zero out the driver statistics */
-#define DEPCA_GET_REG   	0x0c /* Get the Register contents */
-#define DEPCA_SET_REG   	0x0d /* Set the Register contents */
-#define DEPCA_DUMP              0x0f /* Dump the DEPCA Status */
-