提交 1132d5e7 编写于 作者: L Linus Torvalds

Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Stream of fixes has slowed down, only a few this week:

   - Some DT fixes for Allwinner platforms, and addition of a clock to
     the R_CCU clock controller that had been missed.

   - A couple of small DT fixes for am335x-sl50"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: allwinner: a64: Add PLL_PERIPH0 clock to the R_CCU
  ARM: sunxi: h3-h5: Add PLL_PERIPH0 clock to the R_CCU
  ARM: dts: am335x-sl50: Fix cannot claim requested pins for spi0
  ARM: dts: am335x-sl50: Fix card detect pin for mmc1
  arm64: allwinner: h5: Remove syslink to shared DTSI
  ARM: sunxi: h3/h5: fix the compatible of R_CCU
...@@ -220,7 +220,7 @@ ...@@ -220,7 +220,7 @@
mmc1_pins: pinmux_mmc1_pins { mmc1_pins: pinmux_mmc1_pins {
pinctrl-single,pins = < pinctrl-single,pins = <
AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ AM33XX_IOPAD(0x96c, PIN_INPUT | MUX_MODE7) /* uart0_rtsn.gpio1_9 */
>; >;
}; };
...@@ -280,10 +280,6 @@ ...@@ -280,10 +280,6 @@
AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE7) /* nKbdReset - gpmc_ad13.gpio1_13 */ AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE7) /* nKbdReset - gpmc_ad13.gpio1_13 */
AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE7) /* nDispReset - gpmc_ad14.gpio1_14 */ AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE7) /* nDispReset - gpmc_ad14.gpio1_14 */
AM33XX_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7) /* USB1_enPower - gpmc_a1.gpio1_17 */ AM33XX_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7) /* USB1_enPower - gpmc_a1.gpio1_17 */
/* AVR Programming - SPI Bus (bit bang) - Screen and Keyboard */
AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE7) /* Kbd/Disp/BattMOSI spi0_d0.gpio0_3 */
AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE7) /* Kbd/Disp/BattMISO spi0_d1.gpio0_4 */
AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE7) /* Kbd/Disp/BattSCLK spi0_clk.gpio0_2 */
/* PDI Bus - Battery system */ /* PDI Bus - Battery system */
AM33XX_IOPAD(0x840, PIN_INPUT_PULLUP | MUX_MODE7) /* nBattReset gpmc_a0.gpio1_16 */ AM33XX_IOPAD(0x840, PIN_INPUT_PULLUP | MUX_MODE7) /* nBattReset gpmc_a0.gpio1_16 */
AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE7) /* BattPDIData gpmc_ad15.gpio1_15 */ AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE7) /* BattPDIData gpmc_ad15.gpio1_15 */
...@@ -384,7 +380,7 @@ ...@@ -384,7 +380,7 @@
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>; pinctrl-0 = <&mmc1_pins>;
bus-width = <4>; bus-width = <4>;
cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; cd-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vmmcsd_fixed>; vmmc-supply = <&vmmcsd_fixed>;
}; };
......
...@@ -558,10 +558,11 @@ ...@@ -558,10 +558,11 @@
}; };
r_ccu: clock@1f01400 { r_ccu: clock@1f01400 {
compatible = "allwinner,sun50i-a64-r-ccu"; compatible = "allwinner,sun8i-h3-r-ccu";
reg = <0x01f01400 0x100>; reg = <0x01f01400 0x100>;
clocks = <&osc24M>, <&osc32k>, <&iosc>; clocks = <&osc24M>, <&osc32k>, <&iosc>,
clock-names = "hosc", "losc", "iosc"; <&ccu 9>;
clock-names = "hosc", "losc", "iosc", "pll-periph";
#clock-cells = <1>; #clock-cells = <1>;
#reset-cells = <1>; #reset-cells = <1>;
}; };
......
...@@ -406,8 +406,9 @@ ...@@ -406,8 +406,9 @@
r_ccu: clock@1f01400 { r_ccu: clock@1f01400 {
compatible = "allwinner,sun50i-a64-r-ccu"; compatible = "allwinner,sun50i-a64-r-ccu";
reg = <0x01f01400 0x100>; reg = <0x01f01400 0x100>;
clocks = <&osc24M>, <&osc32k>, <&iosc>; clocks = <&osc24M>, <&osc32k>, <&iosc>,
clock-names = "hosc", "losc", "iosc"; <&ccu 11>;
clock-names = "hosc", "losc", "iosc", "pll-periph";
#clock-cells = <1>; #clock-cells = <1>;
#reset-cells = <1>; #reset-cells = <1>;
}; };
......
...@@ -40,7 +40,7 @@ ...@@ -40,7 +40,7 @@
* OTHER DEALINGS IN THE SOFTWARE. * OTHER DEALINGS IN THE SOFTWARE.
*/ */
#include "sunxi-h3-h5.dtsi" #include <arm/sunxi-h3-h5.dtsi>
/ { / {
cpus { cpus {
......
../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册