Merge branch 'for-4.7/phy' into for-4.7/xusb

Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt

+Device tree binding for NVIDIA Tegra XUSB pad controller
+========================================================
+
+The Tegra XUSB pad controller manages a set of I/O lanes (with differential
+signals) which connect directly to pins/pads on the SoC package. Each lane
+is controlled by a HW block referred to as a "pad" in the Tegra hardware
+documentation. Each such "pad" may control either one or multiple lanes,
+and thus contains any logic common to all its lanes. Each lane can be
+separately configured and powered up.
+
+Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or
+super-speed USB. Other lanes are for various types of low-speed, full-speed
+or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller
+contains a software-configurable mux that sits between the I/O controller
+ports (e.g. PCIe) and the lanes.
+
+In addition to per-lane configuration, USB 3.0 ports may require additional
+settings on a per-board basis.
+
+Pads will be represented as children of the top-level XUSB pad controller
+device tree node. Each lane exposed by the pad will be represented by its
+own subnode and can be referenced by users of the lane using the standard
+PHY bindings, as described by the phy-bindings.txt file in this directory.
+
+The Tegra hardware documentation refers to the connection between the XUSB
+pad controller and the XUSB controller as "ports". This is confusing since
+"port" is typically used to denote the physical USB receptacle. The device
+tree binding in this document uses the term "port" to refer to the logical
+abstraction of the signals that are routed to a USB receptacle (i.e. a PHY
+for the USB signal, the VBUS power supply, the USB 2.0 companion port for
+USB 3.0 receptacles, ...).
+
+Required properties:
+--------------------
+- compatible: Must be:
+  - Tegra124: "nvidia,tegra124-xusb-padctl"
+  - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
+  - Tegra210: "nvidia,tegra210-xusb-padctl"
+- reg: Physical base address and length of the controller's registers.
+- resets: Must contain an entry for each entry in reset-names.
+- reset-names: Must include the following entries:
+  - "padctl"
+
+
+Pad nodes:
+==========
+
+A required child node named "pads" contains a list of subnodes, one for each
+of the pads exposed by the XUSB pad controller. Each pad may need additional
+resources that can be referenced in its pad node.
+
+The "status" property is used to enable or disable the use of a pad. If set
+to "disabled", the pad will not be used on the given board. In order to use
+the pad and any of its lanes, this property must be set to "okay".
+
+For Tegra124 and Tegra132, the following pads exist: usb2, ulpi, hsic, pcie
+and sata. No extra resources are required for operation of these pads.
+
+For Tegra210, the following pads exist: usb2, hsic, pcie and sata. Below is
+a description of the properties of each pad.
+
+UTMI pad:
+---------
+
+Required properties:
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Must contain the following entries:
+  - "trk": phandle and specifier referring to the USB2 tracking clock
+
+HSIC pad:
+---------
+
+Required properties:
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Must contain the following entries:
+  - "trk": phandle and specifier referring to the HSIC tracking clock
+
+PCIe pad:
+---------
+
+Required properties:
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Must contain the following entries:
+  - "pll": phandle and specifier referring to the PLLE
+- resets: Must contain an entry for each entry in reset-names.
+- reset-names: Must contain the following entries:
+  - "phy": reset for the PCIe UPHY block
+
+SATA pad:
+---------
+
+Required properties:
+- resets: Must contain an entry for each entry in reset-names.
+- reset-names: Must contain the following entries:
+  - "phy": reset for the SATA UPHY block
+
+
+PHY nodes:
+==========
+
+Each pad node has a child named "lanes" that contains one or more children of
+its own, each representing one of the lanes controlled by the pad.
+
+Required properties:
+--------------------
+- status: Defines the operation status of the PHY. Valid values are:
+  - "disabled": the PHY is disabled
+  - "okay": the PHY is enabled
+- #phy-cells: Should be 0. Since each lane represents a single PHY, there is
+  no need for an additional specifier.
+- nvidia,function: The output function of the PHY. See below for a list of
+  valid functions per SoC generation.
+
+For Tegra124 and Tegra132, the list of valid PHY nodes is given below:
+- usb2: usb2-0, usb2-1, usb2-2
+  - functions: "snps", "xusb", "uart"
+- ulpi: ulpi-0
+  - functions: "snps", "xusb"
+- hsic: hsic-0, hsic-1
+  - functions: "snps", "xusb"
+- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4
+  - functions: "pcie", "usb3-ss"
+- sata: sata-0
+  - functions: "usb3-ss", "sata"
+
+For Tegra210, the list of valid PHY nodes is given below:
+- utmi: utmi-0, utmi-1, utmi-2, utmi-3
+  - functions: "snps", "xusb", "uart"
+- hsic: hsic-0, hsic-1
+  - functions: "snps", "xusb"
+- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, pcie-5, pcie-6
+  - functions: "pcie-x1", "usb3-ss", "pcie-x4"
+- sata: sata-0
+  - functions: "usb3-ss", "sata"
+
+
+Port nodes:
+===========
+
+A required child node named "ports" contains a list of all the ports exposed
+by the XUSB pad controller. Per-port configuration is only required for USB.
+
+USB2 ports:
+-----------
+
+Required properties:
+- status: Defines the operation status of the port. Valid values are:
+  - "disabled": the port is disabled
+  - "okay": the port is enabled
+- mode: A string that determines the mode in which to run the port. Valid
+  values are:
+  - "host": for USB host mode
+  - "device": for USB device mode
+  - "otg": for USB OTG mode
+
+Optional properties:
+- nvidia,internal: A boolean property whose presence determines that a port
+  is internal. In the absence of this property the port is considered to be
+  external.
+- vbus-supply: phandle to a regulator supplying the VBUS voltage.
+
+ULPI ports:
+-----------
+
+Optional properties:
+- status: Defines the operation status of the port. Valid values are:
+  - "disabled": the port is disabled
+  - "okay": the port is enabled
+- nvidia,internal: A boolean property whose presence determines that a port
+  is internal. In the absence of this property the port is considered to be
+  external.
+- vbus-supply: phandle to a regulator supplying the VBUS voltage.
+
+HSIC ports:
+-----------
+
+Required properties:
+- status: Defines the operation status of the port. Valid values are:
+  - "disabled": the port is disabled
+  - "okay": the port is enabled
+
+Optional properties:
+- vbus-supply: phandle to a regulator supplying the VBUS voltage.
+
+Super-speed USB ports:
+----------------------
+
+Required properties:
+- status: Defines the operation status of the port. Valid values are:
+  - "disabled": the port is disabled
+  - "okay": the port is enabled
+- nvidia,usb2-companion: A single cell that specifies the physical port number
+  to map this super-speed USB port to. The range of valid port numbers varies
+  with the SoC generation:
+  - 0-2: for Tegra124 and Tegra132
+  - 0-3: for Tegra210
+
+Optional properties:
+- nvidia,internal: A boolean property whose presence determines that a port
+  is internal. In the absence of this property the port is considered to be
+  external.
+
+For Tegra124 and Tegra132, the XUSB pad controller exposes the following
+ports:
+- 3x USB2: usb2-0, usb2-1, usb2-2
+- 1x ULPI: ulpi-0
+- 2x HSIC: hsic-0, hsic-1
+- 2x super-speed USB: usb3-0, usb3-1
+
+For Tegra210, the XUSB pad controller exposes the following ports:
+- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
+- 2x HSIC: hsic-0, hsic-1
+- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3
+
+
+Examples:
+=========
+
+Tegra124 and Tegra132:
+----------------------
+
+SoC include:
+
+	padctl@7009f000 {
+		/* for Tegra124 */
+		compatible = "nvidia,tegra124-xusb-padctl";
+		/* for Tegra132 */
+		compatible = "nvidia,tegra132-xusb-padctl",
+			     "nvidia,tegra124-xusb-padctl";
+		reg = <0x0 0x7009f000 0x0 0x1000>;
+		resets = <&tegra_car 142>;
+		reset-names = "padctl";
+
+		pads {
+			usb2 {
+				status = "disabled";
+
+				lanes {
+					usb2-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					usb2-1 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					usb2-2 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+
+			ulpi {
+				status = "disabled";
+
+				lanes {
+					ulpi-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+
+			hsic {
+				status = "disabled";
+
+				lanes {
+					hsic-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					hsic-1 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+
+			pcie {
+				status = "disabled";
+
+				lanes {
+					pcie-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-1 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-2 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-3 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-4 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+
+			sata {
+				status = "disabled";
+
+				lanes {
+					sata-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+		};
+
+		ports {
+			usb2-0 {
+				status = "disabled";
+			};
+
+			usb2-1 {
+				status = "disabled";
+			};
+
+			usb2-2 {
+				status = "disabled";
+			};
+
+			ulpi-0 {
+				status = "disabled";
+			};
+
+			hsic-0 {
+				status = "disabled";
+			};
+
+			hsic-1 {
+				status = "disabled";
+			};
+
+			usb3-0 {
+				status = "disabled";
+			};
+
+			usb3-1 {
+				status = "disabled";
+			};
+		};
+	};
+
+Board file:
+
+	padctl@7009f000 {
+		status = "okay";
+
+		pads {
+			usb2 {
+				status = "okay";
+
+				lanes {
+					usb2-0 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+
+					usb2-1 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+
+					usb2-2 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+				};
+			};
+
+			pcie {
+				status = "okay";
+
+				lanes {
+					pcie-0 {
+						nvidia,function = "usb3-ss";
+						status = "okay";
+					};
+
+					pcie-2 {
+						nvidia,function = "pcie";
+						status = "okay";
+					};
+
+					pcie-4 {
+						nvidia,function = "pcie";
+						status = "okay";
+					};
+				};
+			};
+
+			sata {
+				status = "okay";
+
+				lanes {
+					sata-0 {
+						nvidia,function = "sata";
+						status = "okay";
+					};
+				};
+			};
+		};
+
+		ports {
+			/* Micro A/B */
+			usb2-0 {
+				status = "okay";
+				mode = "otg";
+			};
+
+			/* Mini PCIe */
+			usb2-1 {
+				status = "okay";
+				mode = "host";
+			};
+
+			/* USB3 */
+			usb2-2 {
+				status = "okay";
+				mode = "host";
+
+				vbus-supply = <&vdd_usb3_vbus>;
+			};
+
+			usb3-0 {
+				nvidia,port = <2>;
+				status = "okay";
+			};
+		};
+	};
+
+Tegra210:
+---------
+
+SoC include:
+
+	padctl@7009f000 {
+		compatible = "nvidia,tegra210-xusb-padctl";
+		reg = <0x0 0x7009f000 0x0 0x1000>;
+		resets = <&tegra_car 142>;
+		reset-names = "padctl";
+
+		status = "disabled";
+
+		pads {
+			usb2 {
+				clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>;
+				clock-names = "trk";
+				status = "disabled";
+
+				lanes {
+					usb2-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					usb2-1 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					usb2-2 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					usb2-3 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+
+			hsic {
+				clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>;
+				clock-names = "trk";
+				status = "disabled";
+
+				lanes {
+					hsic-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					hsic-1 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+
+			pcie {
+				clocks = <&tegra_car TEGRA210_CLK_PLL_E>;
+				clock-names = "pll";
+				resets = <&tegra_car 205>;
+				reset-names = "phy";
+				status = "disabled";
+
+				lanes {
+					pcie-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-1 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-2 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-3 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-4 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-5 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					pcie-6 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+
+			sata {
+				clocks = <&tegra_car TEGRA210_CLK_PLL_E>;
+				clock-names = "pll";
+				resets = <&tegra_car 204>;
+				reset-names = "phy";
+				status = "disabled";
+
+				lanes {
+					sata-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+		};
+
+		ports {
+			usb2-0 {
+				status = "disabled";
+			};
+
+			usb2-1 {
+				status = "disabled";
+			};
+
+			usb2-2 {
+				status = "disabled";
+			};
+
+			usb2-3 {
+				status = "disabled";
+			};
+
+			hsic-0 {
+				status = "disabled";
+			};
+
+			hsic-1 {
+				status = "disabled";
+			};
+
+			usb3-0 {
+				status = "disabled";
+			};
+
+			usb3-1 {
+				status = "disabled";
+			};
+
+			usb3-2 {
+				status = "disabled";
+			};
+
+			usb3-3 {
+				status = "disabled";
+			};
+		};
+	};
+
+Board file:
+
+	padctl@7009f000 {
+		status = "okay";
+
+		pads {
+			usb2 {
+				status = "okay";
+
+				lanes {
+					usb2-0 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+
+					usb2-1 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+
+					usb2-2 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+
+					usb2-3 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+				};
+			};
+
+			pcie {
+				status = "okay";
+
+				lanes {
+					pcie-0 {
+						nvidia,function = "pcie-x1";
+						status = "okay";
+					};
+
+					pcie-1 {
+						nvidia,function = "pcie-x4";
+						status = "okay";
+					};
+
+					pcie-2 {
+						nvidia,function = "pcie-x4";
+						status = "okay";
+					};
+
+					pcie-3 {
+						nvidia,function = "pcie-x4";
+						status = "okay";
+					};
+
+					pcie-4 {
+						nvidia,function = "pcie-x4";
+						status = "okay";
+					};
+
+					pcie-5 {
+						nvidia,function = "usb3-ss";
+						status = "okay";
+					};
+
+					pcie-6 {
+						nvidia,function = "usb3-ss";
+						status = "okay";
+					};
+				};
+			};
+
+			sata {
+				status = "okay";
+
+				lanes {
+					sata-0 {
+						nvidia,function = "sata";
+						status = "okay";
+					};
+				};
+			};
+		};
+
+		ports {
+			usb2-0 {
+				status = "okay";
+				mode = "otg";
+			};
+
+			usb2-1 {
+				status = "okay";
+				vbus-supply = <&vdd_5v0_rtl>;
+				mode = "host";
+			};
+
+			usb2-2 {
+				status = "okay";
+				vbus-supply = <&vdd_usb_vbus>;
+				mode = "host";
+			};
+
+			usb2-3 {
+				status = "okay";
+				mode = "host";
+			};
+
+			usb3-0 {
+				status = "okay";
+				nvidia,lanes = "pcie-6";
+				nvidia,port = <1>;
+			};
+
+			usb3-1 {
+				status = "okay";
+				nvidia,lanes = "pcie-5";
+				nvidia,port = <2>;
+			};
+		};
+	};

Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt

 Device tree binding for NVIDIA Tegra XUSB pad controller
 ========================================================
 
+NOTE: It turns out that this binding isn't an accurate description of the XUSB
+pad controller. While the description is good enough for the functional subset
+required for PCIe and SATA, it lacks the flexibility to represent the features
+needed for USB. For the new binding, see ../phy/nvidia,tegra-xusb-padctl.txt.
+The binding described in this file is deprecated and should not be used.
+
 The Tegra XUSB pad controller manages a set of lanes, each of which can be
 assigned to one out of a set of different pads. Some of these pads have an
 associated PHY that must be powered up before the pad can be used.

Documentation/phy.txt

@@ -31,16 +31,28 @@ should provide its own implementation of of_xlate. of_xlate is used only for
 dt boot case.
 
 #define of_phy_provider_register(dev, xlate)    \
-        __of_phy_provider_register((dev), THIS_MODULE, (xlate))
+        __of_phy_provider_register((dev), NULL, THIS_MODULE, (xlate))
 
 #define devm_of_phy_provider_register(dev, xlate)       \
-        __devm_of_phy_provider_register((dev), THIS_MODULE, (xlate))
+        __devm_of_phy_provider_register((dev), NULL, THIS_MODULE, (xlate))
 
 of_phy_provider_register and devm_of_phy_provider_register macros can be used to
 register the phy_provider and it takes device and of_xlate as
 arguments. For the dt boot case, all PHY providers should use one of the above
 2 macros to register the PHY provider.
 
+Often the device tree nodes associated with a PHY provider will contain a set
+of children that each represent a single PHY. Some bindings may nest the child
+nodes within extra levels for context and extensibility, in which case the low
+level of_phy_provider_register_full() and devm_of_phy_provider_register_full()
+macros can be used to override the node containing the children.
+
+#define of_phy_provider_register_full(dev, children, xlate) \
+	__of_phy_provider_register(dev, children, THIS_MODULE, xlate)
+
+#define devm_of_phy_provider_register_full(dev, children, xlate) \
+	__devm_of_phy_provider_register_full(dev, children, THIS_MODULE, xlate)
+
 void devm_of_phy_provider_unregister(struct device *dev,
 	struct phy_provider *phy_provider);
 void of_phy_provider_unregister(struct phy_provider *phy_provider);

drivers/clk/tegra/clk-tegra210.c

@@ -175,6 +175,19 @@
 #define UTMIP_PLL_CFG1_FORCE_PLL_ENABLE_POWERDOWN BIT(14)
 #define UTMIP_PLL_CFG1_FORCE_PLL_ACTIVE_POWERDOWN BIT(12)
 
+#define SATA_PLL_CFG0				0x490
+#define SATA_PLL_CFG0_PADPLL_RESET_SWCTL	BIT(0)
+#define SATA_PLL_CFG0_PADPLL_USE_LOCKDET	BIT(2)
+#define SATA_PLL_CFG0_PADPLL_SLEEP_IDDQ		BIT(13)
+#define SATA_PLL_CFG0_SEQ_ENABLE		BIT(24)
+
+#define XUSBIO_PLL_CFG0				0x51c
+#define XUSBIO_PLL_CFG0_PADPLL_RESET_SWCTL	BIT(0)
+#define XUSBIO_PLL_CFG0_CLK_ENABLE_SWCTL	BIT(2)
+#define XUSBIO_PLL_CFG0_PADPLL_USE_LOCKDET	BIT(6)
+#define XUSBIO_PLL_CFG0_PADPLL_SLEEP_IDDQ	BIT(13)
+#define XUSBIO_PLL_CFG0_SEQ_ENABLE		BIT(24)
+
 #define UTMIPLL_HW_PWRDN_CFG0			0x52c
 #define UTMIPLL_HW_PWRDN_CFG0_UTMIPLL_LOCK	BIT(31)
 #define UTMIPLL_HW_PWRDN_CFG0_SEQ_START_STATE	BIT(25)
@@ -416,6 +429,51 @@ static const char *mux_pllmcp_clkm[] = {
 #define PLLU_MISC0_WRITE_MASK		0xbfffffff
 #define PLLU_MISC1_WRITE_MASK		0x00000007
 
+void tegra210_xusb_pll_hw_control_enable(void)
+{
+	u32 val;
+
+	val = readl_relaxed(clk_base + XUSBIO_PLL_CFG0);
+	val &= ~(XUSBIO_PLL_CFG0_CLK_ENABLE_SWCTL |
+		 XUSBIO_PLL_CFG0_PADPLL_RESET_SWCTL);
+	val |= XUSBIO_PLL_CFG0_PADPLL_USE_LOCKDET |
+	       XUSBIO_PLL_CFG0_PADPLL_SLEEP_IDDQ;
+	writel_relaxed(val, clk_base + XUSBIO_PLL_CFG0);
+}
+EXPORT_SYMBOL_GPL(tegra210_xusb_pll_hw_control_enable);
+
+void tegra210_xusb_pll_hw_sequence_start(void)
+{
+	u32 val;
+
+	val = readl_relaxed(clk_base + XUSBIO_PLL_CFG0);
+	val |= XUSBIO_PLL_CFG0_SEQ_ENABLE;
+	writel_relaxed(val, clk_base + XUSBIO_PLL_CFG0);
+}
+EXPORT_SYMBOL_GPL(tegra210_xusb_pll_hw_sequence_start);
+
+void tegra210_sata_pll_hw_control_enable(void)
+{
+	u32 val;
+
+	val = readl_relaxed(clk_base + SATA_PLL_CFG0);
+	val &= ~SATA_PLL_CFG0_PADPLL_RESET_SWCTL;
+	val |= SATA_PLL_CFG0_PADPLL_USE_LOCKDET |
+	       SATA_PLL_CFG0_PADPLL_SLEEP_IDDQ;
+	writel_relaxed(val, clk_base + SATA_PLL_CFG0);
+}
+EXPORT_SYMBOL_GPL(tegra210_sata_pll_hw_control_enable);
+
+void tegra210_sata_pll_hw_sequence_start(void)
+{
+	u32 val;
+
+	val = readl_relaxed(clk_base + SATA_PLL_CFG0);
+	val |= SATA_PLL_CFG0_SEQ_ENABLE;
+	writel_relaxed(val, clk_base + SATA_PLL_CFG0);
+}
+EXPORT_SYMBOL_GPL(tegra210_sata_pll_hw_sequence_start);
+
 static inline void _pll_misc_chk_default(void __iomem *base,
 					struct tegra_clk_pll_params *params,
 					u8 misc_num, u32 default_val, u32 mask)

drivers/phy/Kconfig

@@ -421,4 +421,6 @@ config PHY_CYGNUS_PCIE
 	  Enable this to support the Broadcom Cygnus PCIe PHY.
 	  If unsure, say N.
 
+source "drivers/phy/tegra/Kconfig"
+
 endmenu

drivers/phy/Makefile

@@ -52,3 +52,5 @@ obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
 obj-$(CONFIG_PHY_BRCMSTB_SATA)		+= phy-brcmstb-sata.o
 obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
 obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
+
+obj-$(CONFIG_ARCH_TEGRA) += tegra/

drivers/phy/phy-core.c

@@ -141,7 +141,7 @@ static struct phy_provider *of_phy_provider_lookup(struct device_node *node)
 		if (phy_provider->dev->of_node == node)
 			return phy_provider;
 
-		for_each_child_of_node(phy_provider->dev->of_node, child)
+		for_each_child_of_node(phy_provider->children, child)
 			if (child == node)
 				return phy_provider;
 	}
@@ -811,24 +811,59 @@ EXPORT_SYMBOL_GPL(devm_phy_destroy);
 /**
  * __of_phy_provider_register() - create/register phy provider with the framework
  * @dev: struct device of the phy provider
+ * @children: device node containing children (if different from dev->of_node)
  * @owner: the module owner containing of_xlate
  * @of_xlate: function pointer to obtain phy instance from phy provider
  *
  * Creates struct phy_provider from dev and of_xlate function pointer.
  * This is used in the case of dt boot for finding the phy instance from
  * phy provider.
+ *
+ * If the PHY provider doesn't nest children directly but uses a separate
+ * child node to contain the individual children, the @children parameter
+ * can be used to override the default. If NULL, the default (dev->of_node)
+ * will be used. If non-NULL, the device node must be a child (or further
+ * descendant) of dev->of_node. Otherwise an ERR_PTR()-encoded -EINVAL
+ * error code is returned.
  */
 struct phy_provider *__of_phy_provider_register(struct device *dev,
-	struct module *owner, struct phy * (*of_xlate)(struct device *dev,
-	struct of_phandle_args *args))
+	struct device_node *children, struct module *owner,
+	struct phy * (*of_xlate)(struct device *dev,
+				 struct of_phandle_args *args))
 {
 	struct phy_provider *phy_provider;
 
+	/*
+	 * If specified, the device node containing the children must itself
+	 * be the provider's device node or a child (or further descendant)
+	 * thereof.
+	 */
+	if (children) {
+		struct device_node *parent = of_node_get(children), *next;
+
+		while (parent) {
+			if (parent == dev->of_node)
+				break;
+
+			next = of_get_parent(parent);
+			of_node_put(parent);
+			parent = next;
+		}
+
+		if (!parent)
+			return ERR_PTR(-EINVAL);
+
+		of_node_put(parent);
+	} else {
+		children = dev->of_node;
+	}
+
 	phy_provider = kzalloc(sizeof(*phy_provider), GFP_KERNEL);
 	if (!phy_provider)
 		return ERR_PTR(-ENOMEM);
 
 	phy_provider->dev = dev;
+	phy_provider->children = of_node_get(children);
 	phy_provider->owner = owner;
 	phy_provider->of_xlate = of_xlate;
 
@@ -854,8 +889,9 @@ EXPORT_SYMBOL_GPL(__of_phy_provider_register);
  * on the devres data, then, devres data is freed.
  */
 struct phy_provider *__devm_of_phy_provider_register(struct device *dev,
-	struct module *owner, struct phy * (*of_xlate)(struct device *dev,
-	struct of_phandle_args *args))
+	struct device_node *children, struct module *owner,
+	struct phy * (*of_xlate)(struct device *dev,
+				 struct of_phandle_args *args))
 {
 	struct phy_provider **ptr, *phy_provider;
 
@@ -863,7 +899,8 @@ struct phy_provider *__devm_of_phy_provider_register(struct device *dev,
 	if (!ptr)
 		return ERR_PTR(-ENOMEM);
 
-	phy_provider = __of_phy_provider_register(dev, owner, of_xlate);
+	phy_provider = __of_phy_provider_register(dev, children, owner,
+						  of_xlate);
 	if (!IS_ERR(phy_provider)) {
 		*ptr = phy_provider;
 		devres_add(dev, ptr);
@@ -888,6 +925,7 @@ void of_phy_provider_unregister(struct phy_provider *phy_provider)
 
 	mutex_lock(&phy_provider_mutex);
 	list_del(&phy_provider->list);
+	of_node_put(phy_provider->children);
 	kfree(phy_provider);
 	mutex_unlock(&phy_provider_mutex);
 }

drivers/phy/tegra/Kconfig

+config PHY_TEGRA_XUSB
+	tristate "NVIDIA Tegra XUSB pad controller driver"
+	depends on ARCH_TEGRA
+	help
+	  Choose this option if you have an NVIDIA Tegra SoC.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called phy-tegra-xusb.

drivers/phy/tegra/Makefile

+obj-$(CONFIG_PHY_TEGRA_XUSB) += phy-tegra-xusb.o
+
+phy-tegra-xusb-y += xusb.o
+phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_124_SOC) += xusb-tegra124.o
+phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_132_SOC) += xusb-tegra124.o
+phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_210_SOC) += xusb-tegra210.o

drivers/pinctrl/tegra/pinctrl-tegra-xusb.c

@@ -873,7 +873,7 @@ static const struct of_device_id tegra_xusb_padctl_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, tegra_xusb_padctl_of_match);
 
-static int tegra_xusb_padctl_probe(struct platform_device *pdev)
+int tegra_xusb_padctl_legacy_probe(struct platform_device *pdev)
 {
 	struct tegra_xusb_padctl *padctl;
 	const struct of_device_id *match;
@@ -955,8 +955,9 @@ static int tegra_xusb_padctl_probe(struct platform_device *pdev)
 	reset_control_assert(padctl->rst);
 	return err;
 }
+EXPORT_SYMBOL_GPL(tegra_xusb_padctl_legacy_probe);
 
-static int tegra_xusb_padctl_remove(struct platform_device *pdev)
+int tegra_xusb_padctl_legacy_remove(struct platform_device *pdev)
 {
 	struct tegra_xusb_padctl *padctl = platform_get_drvdata(pdev);
 	int err;
@@ -969,17 +970,4 @@ static int tegra_xusb_padctl_remove(struct platform_device *pdev)
 
 	return err;
 }
-
-static struct platform_driver tegra_xusb_padctl_driver = {
-	.driver = {
-		.name = "tegra-xusb-padctl",
-		.of_match_table = tegra_xusb_padctl_of_match,
-	},
-	.probe = tegra_xusb_padctl_probe,
-	.remove = tegra_xusb_padctl_remove,
-};
-module_platform_driver(tegra_xusb_padctl_driver);
-
-MODULE_AUTHOR("Thierry Reding <treding@nvidia.com>");
-MODULE_DESCRIPTION("Tegra 124 XUSB Pad Control driver");
-MODULE_LICENSE("GPL v2");
+EXPORT_SYMBOL_GPL(tegra_xusb_padctl_legacy_remove);

include/linux/clk/tegra.h

@@ -121,4 +121,9 @@ static inline void tegra_cpu_clock_resume(void)
 }
 #endif
 
+extern void tegra210_xusb_pll_hw_control_enable(void);
+extern void tegra210_xusb_pll_hw_sequence_start(void);
+extern void tegra210_sata_pll_hw_control_enable(void);
+extern void tegra210_sata_pll_hw_sequence_start(void);
+
 #endif /* __LINUX_CLK_TEGRA_H_ */

include/linux/phy/phy.h

@@ -77,6 +77,7 @@ struct phy {
  */
 struct phy_provider {
 	struct device		*dev;
+	struct device_node	*children;
 	struct module		*owner;
 	struct list_head	list;
 	struct phy * (*of_xlate)(struct device *dev,
@@ -93,10 +94,16 @@ struct phy_lookup {
 #define	to_phy(a)	(container_of((a), struct phy, dev))
 
 #define	of_phy_provider_register(dev, xlate)	\
-	__of_phy_provider_register((dev), THIS_MODULE, (xlate))
+	__of_phy_provider_register((dev), NULL, THIS_MODULE, (xlate))
 
 #define	devm_of_phy_provider_register(dev, xlate)	\
-	__devm_of_phy_provider_register((dev), THIS_MODULE, (xlate))
+	__devm_of_phy_provider_register((dev), NULL, THIS_MODULE, (xlate))
+
+#define of_phy_provider_register_full(dev, children, xlate) \
+	__of_phy_provider_register(dev, children, THIS_MODULE, xlate)
+
+#define devm_of_phy_provider_register_full(dev, children, xlate) \
+	__devm_of_phy_provider_register(dev, children, THIS_MODULE, xlate)
 
 static inline void phy_set_drvdata(struct phy *phy, void *data)
 {
@@ -147,11 +154,13 @@ struct phy *devm_phy_create(struct device *dev, struct device_node *node,
 void phy_destroy(struct phy *phy);
 void devm_phy_destroy(struct device *dev, struct phy *phy);
 struct phy_provider *__of_phy_provider_register(struct device *dev,
-	struct module *owner, struct phy * (*of_xlate)(struct device *dev,
-	struct of_phandle_args *args));
+	struct device_node *children, struct module *owner,
+	struct phy * (*of_xlate)(struct device *dev,
+				 struct of_phandle_args *args));
 struct phy_provider *__devm_of_phy_provider_register(struct device *dev,
-	struct module *owner, struct phy * (*of_xlate)(struct device *dev,
-	struct of_phandle_args *args));
+	struct device_node *children, struct module *owner,
+	struct phy * (*of_xlate)(struct device *dev,
+				 struct of_phandle_args *args));
 void of_phy_provider_unregister(struct phy_provider *phy_provider);
 void devm_of_phy_provider_unregister(struct device *dev,
 	struct phy_provider *phy_provider);
@@ -312,15 +321,17 @@ static inline void devm_phy_destroy(struct device *dev, struct phy *phy)
 }
 
 static inline struct phy_provider *__of_phy_provider_register(
-	struct device *dev, struct module *owner, struct phy * (*of_xlate)(
-	struct device *dev, struct of_phandle_args *args))
+	struct device *dev, struct device_node *children, struct module *owner,
+	struct phy * (*of_xlate)(struct device *dev,
+				 struct of_phandle_args *args))
 {
 	return ERR_PTR(-ENOSYS);
 }
 
 static inline struct phy_provider *__devm_of_phy_provider_register(struct device
-	*dev, struct module *owner, struct phy * (*of_xlate)(struct device *dev,
-	struct of_phandle_args *args))
+	*dev, struct device_node *children, struct module *owner,
+	struct phy * (*of_xlate)(struct device *dev,
+				 struct of_phandle_args *args))
 {
 	return ERR_PTR(-ENOSYS);
 }

include/linux/phy/tegra/xusb.h

+/*
+ * Copyright (c) 2016, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ */
+
+#ifndef PHY_TEGRA_XUSB_H
+#define PHY_TEGRA_XUSB_H
+
+struct tegra_xusb_padctl;
+struct device;
+
+struct tegra_xusb_padctl *tegra_xusb_padctl_get(struct device *dev);
+void tegra_xusb_padctl_put(struct tegra_xusb_padctl *padctl);
+
+int tegra_xusb_padctl_usb3_save_context(struct tegra_xusb_padctl *padctl,
+					unsigned int port);
+int tegra_xusb_padctl_hsic_set_idle(struct tegra_xusb_padctl *padctl,
+				    unsigned int port, bool idle);
+int tegra_xusb_padctl_usb3_set_lfps_detect(struct tegra_xusb_padctl *padctl,
+					   unsigned int port, bool enable);
+
+#endif /* PHY_TEGRA_XUSB_H */

include/soc/tegra/fuse.h

@@ -26,6 +26,7 @@
 
 #define TEGRA_FUSE_SKU_CALIB_0	0xf0
 #define TEGRA30_FUSE_SATA_CALIB	0x124
+#define TEGRA_FUSE_USB_CALIB_EXT_0 0x250
 
 #ifndef __ASSEMBLY__