ARM: 5630/1: Add support for Eukrea's CPUAT91

CPUAT91 is based on Atmel's AT91RM9200 with up to 16MB Strataflash,
up to 128MB SDRAM and an ethernet PHY in RMII mode.
Signed-off-by: NEric Benard <ebenard@eukrea.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-at91/Kconfig

@@ -156,6 +156,13 @@ config MACH_YL9200
 	help
 	  Select this if you are using the ucDragon YL-9200 board.
 
+config MACH_CPUAT91
+	bool "Eukrea CPUAT91"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using the Eukrea Electromatique's
+	  CPUAT91 board <http://www.eukrea.com/>.
+
 endif
 
 # ----------------------------------------------------------

arch/arm/mach-at91/Makefile

@@ -34,6 +34,7 @@ obj-$(CONFIG_MACH_KAFA)		+= board-kafa.o
 obj-$(CONFIG_MACH_PICOTUX2XX)	+= board-picotux200.o
 obj-$(CONFIG_MACH_ECBAT91)	+= board-ecbat91.o
 obj-$(CONFIG_MACH_YL9200)	+= board-yl-9200.o
+obj-$(CONFIG_MACH_CPUAT91)	+= board-cpuat91.o
 
 # AT91SAM9260 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o

arch/arm/mach-at91/board-cpuat91.c

+/*
+ * linux/arch/arm/mach-at91/board-cpuat91.c
+ *
+ *  Copyright (C) 2009 Eric Benard - eric@eukrea.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mtd/plat-ram.h>
+
+#include <mach/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
+
+#include "generic.h"
+
+static struct gpio_led cpuat91_leds[] = {
+	{
+		.name			= "led1",
+		.default_trigger	= "heartbeat",
+		.active_low		= 1,
+		.gpio			= AT91_PIN_PC0,
+	},
+};
+
+static void __init cpuat91_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
+
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
+		ATMEL_UART_RTS);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
+		ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
+		ATMEL_UART_DCD | ATMEL_UART_RI);
+
+	/* USART2 on ttyS3 (Rx, Tx) */
+	at91_register_uart(AT91RM9200_ID_US2, 3, 0);
+
+	/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
+		ATMEL_UART_RTS);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+static void __init cpuat91_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata cpuat91_eth_data = {
+	.is_rmii	= 1,
+};
+
+static struct at91_usbh_data __initdata cpuat91_usbh_data = {
+	.ports		= 1,
+};
+
+static struct at91_udc_data __initdata cpuat91_udc_data = {
+	.vbus_pin	= AT91_PIN_PC15,
+	.pullup_pin	= AT91_PIN_PC14,
+};
+
+static struct at91_mmc_data __initdata cpuat91_mmc_data = {
+	.det_pin	= AT91_PIN_PC2,
+	.wire4		= 1,
+};
+
+static struct physmap_flash_data cpuat91_flash_data = {
+	.width		= 2,
+};
+
+static struct resource cpuat91_flash_resource = {
+	.start		= AT91_CHIPSELECT_0,
+	.end		= AT91_CHIPSELECT_0 + SZ_16M - 1,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device cpuat91_norflash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev	= {
+		.platform_data	= &cpuat91_flash_data,
+	},
+	.resource	= &cpuat91_flash_resource,
+	.num_resources	= 1,
+};
+
+#ifdef CONFIG_MTD_PLATRAM
+struct platdata_mtd_ram at91_sram_pdata = {
+	.mapname	= "SRAM",
+	.bankwidth	= 2,
+};
+
+static struct resource at91_sram_resource[] = {
+	[0] = {
+		.start = AT91RM9200_SRAM_BASE,
+		.end   = AT91RM9200_SRAM_BASE + AT91RM9200_SRAM_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device at91_sram = {
+	.name		= "mtd-ram",
+	.id		= 0,
+	.resource	= at91_sram_resource,
+	.num_resources	= ARRAY_SIZE(at91_sram_resource),
+	.dev	= {
+		.platform_data = &at91_sram_pdata,
+	},
+};
+#endif /* MTD_PLATRAM */
+
+static struct platform_device *platform_devices[] __initdata = {
+	&cpuat91_norflash,
+#ifdef CONFIG_MTD_PLATRAM
+	&at91_sram,
+#endif /* CONFIG_MTD_PLATRAM */
+};
+
+static void __init cpuat91_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* LEDs. */
+	at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds));
+	/* Ethernet */
+	at91_add_device_eth(&cpuat91_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&cpuat91_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&cpuat91_udc_data);
+	/* MMC */
+	at91_add_device_mmc(0, &cpuat91_mmc_data);
+	/* I2C */
+	at91_add_device_i2c(NULL, 0);
+	/* Platform devices */
+	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+}
+
+MACHINE_START(CPUAT91, "Eukrea")
+	/* Maintainer: Eric Benard - EUKREA Electromatique */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= cpuat91_map_io,
+	.init_irq	= cpuat91_init_irq,
+	.init_machine	= cpuat91_board_init,
+MACHINE_END