ktest: Add POST/PRE_BUILD options

There are some cases that a patch may be needed to apply to the kernel
in patchcheck or bisect tests. Adding a PRE_BUILD option to apply the
patch and POST_BUILD to remove it, allows for this to be done easily.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

tools/testing/ktest/ktest.pl

@@ -63,6 +63,10 @@ my $output_config;
 my $test_type;
 my $build_type;
 my $build_options;
+my $pre_build;
+my $post_build;
+my $pre_build_die;
+my $post_build_die;
 my $reboot_type;
 my $reboot_script;
 my $power_cycle;
@@ -1189,6 +1193,14 @@ sub build {
 
     unlink $buildlog;
 
+    if (defined($pre_build)) {
+	my $ret = run_command $pre_build;
+	if (!$ret && defined($pre_build_die) &&
+	    $pre_build_die) {
+	    dodie "failed to pre_build\n";
+	}
+    }
+
     if ($type =~ /^useconfig:(.*)/) {
 	run_command "cp $1 $output_config" or
 	    dodie "could not copy $1 to .config";
@@ -1236,13 +1248,22 @@ sub build {
     make_oldconfig;
 
     $redirect = "$buildlog";
-    if (!run_command "$make $build_options") {
-	undef $redirect;
+    my $build_ret = run_command "$make $build_options";
+    undef $redirect;
+
+    if (defined($post_build)) {
+	my $ret = run_command $post_build;
+	if (!$ret && defined($post_build_die) &&
+	    $post_build_die) {
+	    dodie "failed to post_build\n";
+	}
+    }
+
+    if (!$build_ret) {
 	# bisect may need this to pass
 	return 0 if ($in_bisect);
 	fail "failed build" and return 0;
     }
-    undef $redirect;
 
     return 1;
 }
@@ -2244,6 +2265,10 @@ for (my $i = 1; $i <= $opt{"NUM_TESTS"}; $i++) {
     $test_type = set_test_option("TEST_TYPE", $i);
     $build_type = set_test_option("BUILD_TYPE", $i);
     $build_options = set_test_option("BUILD_OPTIONS", $i);
+    $pre_build = set_test_option("PRE_BUILD", $i);
+    $post_build = set_test_option("POST_BUILD", $i);
+    $pre_build_die = set_test_option("PRE_BUILD_DIE", $i);
+    $post_build_die = set_test_option("POST_BUILD_DIE", $i);
     $power_cycle = set_test_option("POWER_CYCLE", $i);
     $reboot = set_test_option("REBOOT", $i);
     $noclean = set_test_option("BUILD_NOCLEAN", $i);

tools/testing/ktest/sample.conf

@@ -293,6 +293,38 @@
 # or on some systems:
 #POST_INSTALL = ssh user@target /sbin/dracut -f /boot/initramfs-test.img $KERNEL_VERSION
 
+# If there is a script that you require to run before the build is done
+# you can specify it with PRE_BUILD.
+#
+# One example may be if you must add a temporary patch to the build to
+# fix a unrelated bug to perform a patchcheck test. This will apply the
+# patch before each build that is made. Use the POST_BUILD to do a git reset --hard
+# to remove the patch.
+#
+# (default undef)
+#PRE_BUILD = cd ${BUILD_DIR} && patch -p1 < /tmp/temp.patch
+
+# To specify if the test should fail if the PRE_BUILD fails,
+# PRE_BUILD_DIE needs to be set to 1. Otherwise the PRE_BUILD
+# result is ignored.
+# (default 0)
+# PRE_BUILD_DIE = 1
+
+# If there is a script that should run after the build is done
+# you can specify it with POST_BUILD.
+#
+# As the example in PRE_BUILD, POST_BUILD can be used to reset modifications
+# made by the PRE_BUILD.
+#
+# (default undef)
+#POST_BUILD = cd ${BUILD_DIR} && git reset --hard
+
+# To specify if the test should fail if the POST_BUILD fails,
+# POST_BUILD_DIE needs to be set to 1. Otherwise the POST_BUILD
+# result is ignored.
+# (default 0)
+#POST_BUILD_DIE = 1
+
 # Way to reboot the box to the test kernel.
 # Only valid options so far are "grub" and "script"
 # (default grub)