powerpc/8xx: Fixup DAR from buggy dcbX instructions.

This is an assembler version to fixup DAR not being set
by dcbX, icbi instructions. There are two versions, one
uses selfmodifing code, the other uses a
jump table but is much bigger(default).
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

arch/powerpc/kernel/head_8xx.S

@@ -494,11 +494,16 @@ DataTLBError:
 
 	mfspr	r10, SPRN_DAR
 	cmpwi	cr0, r10, 0x00f0
-	beq-	2f	/* must be a buggy dcbX, icbi insn. */
-
+	beq-	FixupDAR	/* must be a buggy dcbX, icbi insn. */
+DARFixed:/* Return from dcbx instruction bug workaround, r10 holds value of DAR */
 	mfspr	r11, SPRN_DSISR
-	andis.	r11, r11, 0x4800	/* !translation or protection */
-	bne	2f	/* branch if either is set */
+	/* As the DAR fixup may clear store we may have all 3 states zero.
+	 * Make sure only 0x0200(store) falls down into DIRTY handling
+	 */
+	andis.	r11, r11, 0x4a00	/* !translation, protection or store */
+	srwi	r11, r11, 16
+	cmpwi	cr0, r11, 0x0200	/* just store ? */
+	bne	2f
 	/* Only Change bit left now, do it here as it is faster
 	 * than trapping to the C fault handler.
 	*/
@@ -604,6 +609,140 @@ DataTLBError:
 
 	. = 0x2000
 
+/* This is the procedure to calculate the data EA for buggy dcbx,dcbi instructions
+ * by decoding the registers used by the dcbx instruction and adding them.
+ * DAR is set to the calculated address and r10 also holds the EA on exit.
+ */
+ /* define if you don't want to use self modifying code */
+#define NO_SELF_MODIFYING_CODE
+FixupDAR:/* Entry point for dcbx workaround. */
+	/* fetch instruction from memory. */
+	mfspr	r10, SPRN_SRR0
+	DO_8xx_CPU6(0x3780, r3)
+	mtspr	SPRN_MD_EPN, r10
+	mfspr	r11, SPRN_M_TWB	/* Get level 1 table entry address */
+	cmplwi	cr0, r11, 0x0800
+	blt-	3f		/* Branch if user space */
+	lis	r11, (swapper_pg_dir-PAGE_OFFSET)@h
+	ori	r11, r11, (swapper_pg_dir-PAGE_OFFSET)@l
+	rlwimi	r11, r10, 32-20, 0xffc /* r11 = r11&~0xffc|(r10>>20)&0xffc */
+3:	lwz	r11, 0(r11)	/* Get the level 1 entry */
+	DO_8xx_CPU6(0x3b80, r3)
+	mtspr	SPRN_MD_TWC, r11	/* Load pte table base address */
+	mfspr	r11, SPRN_MD_TWC	/* ....and get the pte address */
+	lwz	r11, 0(r11)	/* Get the pte */
+	/* concat physical page address(r11) and page offset(r10) */
+	rlwimi	r11, r10, 0, 20, 31
+	lwz	r11,0(r11)
+/* Check if it really is a dcbx instruction. */
+/* dcbt and dcbtst does not generate DTLB Misses/Errors,
+ * no need to include them here */
+	srwi	r10, r11, 26	/* check if major OP code is 31 */
+	cmpwi	cr0, r10, 31
+	bne-	141f
+	rlwinm	r10, r11, 0, 21, 30
+	cmpwi	cr0, r10, 2028	/* Is dcbz? */
+	beq+	142f
+	cmpwi	cr0, r10, 940	/* Is dcbi? */
+	beq+	142f
+	cmpwi	cr0, r10, 108	/* Is dcbst? */
+	beq+	144f		/* Fix up store bit! */
+	cmpwi	cr0, r10, 172	/* Is dcbf? */
+	beq+	142f
+	cmpwi	cr0, r10, 1964	/* Is icbi? */
+	beq+	142f
+141:	mfspr	r10, SPRN_DAR	/* r10 must hold DAR at exit */
+	b	DARFixed	/* Nope, go back to normal TLB processing */
+
+144:	mfspr	r10, SPRN_DSISR
+	rlwinm	r10, r10,0,7,5	/* Clear store bit for buggy dcbst insn */
+	mtspr	SPRN_DSISR, r10
+142:	/* continue, it was a dcbx, dcbi instruction. */
+#ifdef CONFIG_8xx_CPU6
+	lwz	r3, 8(r0)	/* restore r3 from memory */
+#endif
+#ifndef NO_SELF_MODIFYING_CODE
+	andis.	r10,r11,0x1f	/* test if reg RA is r0 */
+	li	r10,modified_instr@l
+	dcbtst	r0,r10		/* touch for store */
+	rlwinm	r11,r11,0,0,20	/* Zero lower 10 bits */
+	oris	r11,r11,640	/* Transform instr. to a "add r10,RA,RB" */
+	ori	r11,r11,532
+	stw	r11,0(r10)	/* store add/and instruction */
+	dcbf	0,r10		/* flush new instr. to memory. */
+	icbi	0,r10		/* invalidate instr. cache line */
+	lwz	r11, 4(r0)	/* restore r11 from memory */
+	mfspr	r10, SPRN_M_TW	/* restore r10 from M_TW */
+	isync			/* Wait until new instr is loaded from memory */
+modified_instr:
+	.space	4		/* this is where the add instr. is stored */
+	bne+	143f
+	subf	r10,r0,r10	/* r10=r10-r0, only if reg RA is r0 */
+143:	mtdar	r10		/* store faulting EA in DAR */
+	b	DARFixed	/* Go back to normal TLB handling */
+#else
+	mfctr	r10
+	mtdar	r10			/* save ctr reg in DAR */
+	rlwinm	r10, r11, 24, 24, 28	/* offset into jump table for reg RB */
+	addi	r10, r10, 150f@l	/* add start of table */
+	mtctr	r10			/* load ctr with jump address */
+	xor	r10, r10, r10		/* sum starts at zero */
+	bctr				/* jump into table */
+150:
+	add	r10, r10, r0	;b	151f
+	add	r10, r10, r1	;b	151f
+	add	r10, r10, r2	;b	151f
+	add	r10, r10, r3	;b	151f
+	add	r10, r10, r4	;b	151f
+	add	r10, r10, r5	;b	151f
+	add	r10, r10, r6	;b	151f
+	add	r10, r10, r7	;b	151f
+	add	r10, r10, r8	;b	151f
+	add	r10, r10, r9	;b	151f
+	mtctr	r11	;b	154f	/* r10 needs special handling */
+	mtctr	r11	;b	153f	/* r11 needs special handling */
+	add	r10, r10, r12	;b	151f
+	add	r10, r10, r13	;b	151f
+	add	r10, r10, r14	;b	151f
+	add	r10, r10, r15	;b	151f
+	add	r10, r10, r16	;b	151f
+	add	r10, r10, r17	;b	151f
+	add	r10, r10, r18	;b	151f
+	add	r10, r10, r19	;b	151f
+	add	r10, r10, r20	;b	151f
+	add	r10, r10, r21	;b	151f
+	add	r10, r10, r22	;b	151f
+	add	r10, r10, r23	;b	151f
+	add	r10, r10, r24	;b	151f
+	add	r10, r10, r25	;b	151f
+	add	r10, r10, r26	;b	151f
+	add	r10, r10, r27	;b	151f
+	add	r10, r10, r28	;b	151f
+	add	r10, r10, r29	;b	151f
+	add	r10, r10, r30	;b	151f
+	add	r10, r10, r31
+151:
+	rlwinm. r11,r11,19,24,28	/* offset into jump table for reg RA */
+	beq	152f			/* if reg RA is zero, don't add it */
+	addi	r11, r11, 150b@l	/* add start of table */
+	mtctr	r11			/* load ctr with jump address */
+	rlwinm	r11,r11,0,16,10		/* make sure we don't execute this more than once */
+	bctr				/* jump into table */
+152:
+	mfdar	r11
+	mtctr	r11			/* restore ctr reg from DAR */
+	mtdar	r10			/* save fault EA to DAR */
+	b	DARFixed		/* Go back to normal TLB handling */
+
+	/* special handling for r10,r11 since these are modified already */
+153:	lwz	r11, 4(r0)	/* load r11 from memory */
+	b	155f
+154:	mfspr	r11, SPRN_M_TW	/* load r10 from M_TW */
+155:	add	r10, r10, r11	/* add it */
+	mfctr	r11		/* restore r11 */
+	b	151b
+#endif
+
 	.globl	giveup_fpu
 giveup_fpu:
 	blr