blackfin.c 10.0 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
/*
 * MUSB OTG controller driver for Blackfin Processors
 *
 * Copyright 2006-2008 Analog Devices Inc.
 *
 * Enter bugs at http://blackfin.uclinux.org/
 *
 * Licensed under the GPL-2 or later.
 */

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/init.h>
#include <linux/list.h>
#include <linux/gpio.h>
#include <linux/io.h>

#include <asm/cacheflush.h>

#include "musb_core.h"
#include "blackfin.h"

/*
 * Load an endpoint's FIFO
 */
void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src)
{
	void __iomem *fifo = hw_ep->fifo;
	void __iomem *epio = hw_ep->regs;
31
	u8 epnum = hw_ep->epnum;
32 33 34 35 36 37 38 39 40 41

	prefetch((u8 *)src);

	musb_writew(epio, MUSB_TXCOUNT, len);

	DBG(4, "TX ep%d fifo %p count %d buf %p, epio %p\n",
			hw_ep->epnum, fifo, len, src, epio);

	dump_fifo_data(src, len);

42
	if (!ANOMALY_05000380 && epnum != 0) {
43 44 45 46
		u16 dma_reg;

		flush_dcache_range((unsigned long)src,
			(unsigned long)(src + len));
47 48

		/* Setup DMA address register */
49
		dma_reg = (u32)src;
50 51 52
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
		SSYNC();

53
		dma_reg = (u32)src >> 16;
54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
		SSYNC();

		/* Setup DMA count register */
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_LOW), len);
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_HIGH), 0);
		SSYNC();

		/* Enable the DMA */
		dma_reg = (epnum << 4) | DMA_ENA | INT_ENA | DIRECTION;
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), dma_reg);
		SSYNC();

		/* Wait for compelete */
		while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << epnum)))
			cpu_relax();

		/* acknowledge dma interrupt */
		bfin_write_USB_DMA_INTERRUPT(1 << epnum);
		SSYNC();

		/* Reset DMA */
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), 0);
		SSYNC();
	} else {
		SSYNC();

		if (unlikely((unsigned long)src & 0x01))
82
			outsw_8((unsigned long)fifo, src, (len + 1) >> 1);
83
		else
84
			outsw((unsigned long)fifo, src, (len + 1) >> 1);
85
	}
86 87 88 89 90 91 92 93 94
}
/*
 * Unload an endpoint's FIFO
 */
void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
{
	void __iomem *fifo = hw_ep->fifo;
	u8 epnum = hw_ep->epnum;

95
	if (ANOMALY_05000467 && epnum != 0) {
96
		u16 dma_reg;
97

98 99
		invalidate_dcache_range((unsigned long)dst,
			(unsigned long)(dst + len));
100 101

		/* Setup DMA address register */
102
		dma_reg = (u32)dst;
103 104 105
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
		SSYNC();

106
		dma_reg = (u32)dst >> 16;
107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
		SSYNC();

		/* Setup DMA count register */
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_LOW), len);
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_HIGH), 0);
		SSYNC();

		/* Enable the DMA */
		dma_reg = (epnum << 4) | DMA_ENA | INT_ENA;
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), dma_reg);
		SSYNC();

		/* Wait for compelete */
		while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << epnum)))
			cpu_relax();

		/* acknowledge dma interrupt */
		bfin_write_USB_DMA_INTERRUPT(1 << epnum);
		SSYNC();

		/* Reset DMA */
		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), 0);
		SSYNC();
	} else {
		SSYNC();
		/* Read the last byte of packet with odd size from address fifo + 4
		 * to trigger 1 byte access to EP0 FIFO.
		 */
		if (len == 1)
			*dst = (u8)inw((unsigned long)fifo + 4);
		else {
			if (unlikely((unsigned long)dst & 0x01))
				insw_8((unsigned long)fifo, dst, len >> 1);
			else
				insw((unsigned long)fifo, dst, len >> 1);

			if (len & 0x01)
				*(dst + len - 1) = (u8)inw((unsigned long)fifo + 4);
		}
	}
148 149 150
	DBG(4, "%cX ep%d fifo %p count %d buf %p\n",
			'R', hw_ep->epnum, fifo, len, dst);

151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172
	dump_fifo_data(dst, len);
}

static irqreturn_t blackfin_interrupt(int irq, void *__hci)
{
	unsigned long	flags;
	irqreturn_t	retval = IRQ_NONE;
	struct musb	*musb = __hci;

	spin_lock_irqsave(&musb->lock, flags);

	musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
	musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
	musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);

	if (musb->int_usb || musb->int_tx || musb->int_rx) {
		musb_writeb(musb->mregs, MUSB_INTRUSB, musb->int_usb);
		musb_writew(musb->mregs, MUSB_INTRTX, musb->int_tx);
		musb_writew(musb->mregs, MUSB_INTRRX, musb->int_rx);
		retval = musb_interrupt(musb);
	}

173 174 175 176 177 178 179
	/* Start sampling ID pin, when plug is removed from MUSB */
	if (is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
		|| musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) {
		mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
		musb->a_wait_bcon = TIMER_DELAY;
	}

180 181
	spin_unlock_irqrestore(&musb->lock, flags);

182
	return retval;
183 184 185 186 187 188 189
}

static void musb_conn_timer_handler(unsigned long _musb)
{
	struct musb *musb = (void *)_musb;
	unsigned long flags;
	u16 val;
190
	static u8 toggle;
191 192

	spin_lock_irqsave(&musb->lock, flags);
193
	switch (musb->xceiv->state) {
194 195 196 197
	case OTG_STATE_A_IDLE:
	case OTG_STATE_A_WAIT_BCON:
		/* Start a new session */
		val = musb_readw(musb->mregs, MUSB_DEVCTL);
198 199
		val &= ~MUSB_DEVCTL_SESSION;
		musb_writew(musb->mregs, MUSB_DEVCTL, val);
200 201
		val |= MUSB_DEVCTL_SESSION;
		musb_writew(musb->mregs, MUSB_DEVCTL, val);
202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224
		/* Check if musb is host or peripheral. */
		val = musb_readw(musb->mregs, MUSB_DEVCTL);

		if (!(val & MUSB_DEVCTL_BDEVICE)) {
			gpio_set_value(musb->config->gpio_vrsel, 1);
			musb->xceiv->state = OTG_STATE_A_WAIT_BCON;
		} else {
			gpio_set_value(musb->config->gpio_vrsel, 0);
			/* Ignore VBUSERROR and SUSPEND IRQ */
			val = musb_readb(musb->mregs, MUSB_INTRUSBE);
			val &= ~MUSB_INTR_VBUSERROR;
			musb_writeb(musb->mregs, MUSB_INTRUSBE, val);

			val = MUSB_INTR_SUSPEND | MUSB_INTR_VBUSERROR;
			musb_writeb(musb->mregs, MUSB_INTRUSB, val);
			if (is_otg_enabled(musb))
				musb->xceiv->state = OTG_STATE_B_IDLE;
			else
				musb_writeb(musb->mregs, MUSB_POWER, MUSB_POWER_HSENAB);
		}
		mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
		break;
	case OTG_STATE_B_IDLE:
225

226 227 228 229 230 231 232 233
		if (!is_peripheral_enabled(musb))
			break;
		/* Start a new session.  It seems that MUSB needs taking
		 * some time to recognize the type of the plug inserted?
		 */
		val = musb_readw(musb->mregs, MUSB_DEVCTL);
		val |= MUSB_DEVCTL_SESSION;
		musb_writew(musb->mregs, MUSB_DEVCTL, val);
234
		val = musb_readw(musb->mregs, MUSB_DEVCTL);
235

236 237
		if (!(val & MUSB_DEVCTL_BDEVICE)) {
			gpio_set_value(musb->config->gpio_vrsel, 1);
238
			musb->xceiv->state = OTG_STATE_A_WAIT_BCON;
239 240 241 242 243 244 245 246 247 248 249
		} else {
			gpio_set_value(musb->config->gpio_vrsel, 0);

			/* Ignore VBUSERROR and SUSPEND IRQ */
			val = musb_readb(musb->mregs, MUSB_INTRUSBE);
			val &= ~MUSB_INTR_VBUSERROR;
			musb_writeb(musb->mregs, MUSB_INTRUSBE, val);

			val = MUSB_INTR_SUSPEND | MUSB_INTR_VBUSERROR;
			musb_writeb(musb->mregs, MUSB_INTRUSB, val);

250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268
			/* Toggle the Soft Conn bit, so that we can response to
			 * the inserting of either A-plug or B-plug.
			 */
			if (toggle) {
				val = musb_readb(musb->mregs, MUSB_POWER);
				val &= ~MUSB_POWER_SOFTCONN;
				musb_writeb(musb->mregs, MUSB_POWER, val);
				toggle = 0;
			} else {
				val = musb_readb(musb->mregs, MUSB_POWER);
				val |= MUSB_POWER_SOFTCONN;
				musb_writeb(musb->mregs, MUSB_POWER, val);
				toggle = 1;
			}
			/* The delay time is set to 1/4 second by default,
			 * shortening it, if accelerating A-plug detection
			 * is needed in OTG mode.
			 */
			mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY / 4);
269 270 271 272 273 274 275 276 277 278 279 280 281
		}
		break;
	default:
		DBG(1, "%s state not handled\n", otg_state_string(musb));
		break;
	}
	spin_unlock_irqrestore(&musb->lock, flags);

	DBG(4, "state is %s\n", otg_state_string(musb));
}

void musb_platform_enable(struct musb *musb)
{
282
	if (!is_otg_enabled(musb) && is_host_enabled(musb)) {
283 284 285 286 287 288 289 290 291 292 293
		mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
		musb->a_wait_bcon = TIMER_DELAY;
	}
}

void musb_platform_disable(struct musb *musb)
{
}

static void bfin_set_vbus(struct musb *musb, int is_on)
{
294 295 296 297
	int value = musb->config->gpio_vrsel_active;
	if (!is_on)
		value = !value;
	gpio_set_value(musb->config->gpio_vrsel, value);
298 299 300 301 302 303 304 305 306 307 308 309 310 311

	DBG(1, "VBUS %s, devctl %02x "
		/* otg %3x conf %08x prcm %08x */ "\n",
		otg_state_string(musb),
		musb_readb(musb->mregs, MUSB_DEVCTL));
}

static int bfin_set_power(struct otg_transceiver *x, unsigned mA)
{
	return 0;
}

void musb_platform_try_idle(struct musb *musb, unsigned long timeout)
{
312
	if (!is_otg_enabled(musb) && is_host_enabled(musb))
313 314 315 316 317 318 319 320
		mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
}

int musb_platform_get_vbus_status(struct musb *musb)
{
	return 0;
}

321
int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
322
{
323
	return -EIO;
324 325
}

326
int __init musb_platform_init(struct musb *musb, void *board_data)
327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342
{

	/*
	 * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
	 * and OTG HOST modes, while rev 1.1 and greater require PE7 to
	 * be low for DEVICE mode and high for HOST mode. We set it high
	 * here because we are in host mode
	 */

	if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
		printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d \n",
			musb->config->gpio_vrsel);
		return -ENODEV;
	}
	gpio_direction_output(musb->config->gpio_vrsel, 0);

343 344 345 346 347
	usb_nop_xceiv_register();
	musb->xceiv = otg_get_transceiver();
	if (!musb->xceiv)
		return -ENODEV;

348 349 350 351
	if (ANOMALY_05000346) {
		bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
		SSYNC();
	}
352

353 354 355 356
	if (ANOMALY_05000347) {
		bfin_write_USB_APHY_CNTRL(0x0);
		SSYNC();
	}
357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387

	/* Configure PLL oscillator register */
	bfin_write_USB_PLLOSC_CTRL(0x30a8);
	SSYNC();

	bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1);
	SSYNC();

	bfin_write_USB_EP_NI0_RXMAXP(64);
	SSYNC();

	bfin_write_USB_EP_NI0_TXMAXP(64);
	SSYNC();

	/* Route INTRUSB/INTR_RX/INTR_TX to USB_INT0*/
	bfin_write_USB_GLOBINTR(0x7);
	SSYNC();

	bfin_write_USB_GLOBAL_CTL(GLOBAL_ENA | EP1_TX_ENA | EP2_TX_ENA |
				EP3_TX_ENA | EP4_TX_ENA | EP5_TX_ENA |
				EP6_TX_ENA | EP7_TX_ENA | EP1_RX_ENA |
				EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
				EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
	SSYNC();

	if (is_host_enabled(musb)) {
		musb->board_set_vbus = bfin_set_vbus;
		setup_timer(&musb_conn_timer,
			musb_conn_timer_handler, (unsigned long) musb);
	}
	if (is_peripheral_enabled(musb))
388
		musb->xceiv->set_power = bfin_set_power;
389 390 391 392 393 394 395 396 397 398 399 400 401

	musb->isr = blackfin_interrupt;

	return 0;
}

int musb_platform_exit(struct musb *musb)
{

	gpio_free(musb->config->gpio_vrsel);

	return 0;
}