Kconfig 16.1 KB
Newer Older
1 2 3 4 5 6 7
config LEDS_GPIO_REGISTER
	bool
	help
	  This option provides the function gpio_led_register_device.
	  As this function is used by arch code it must not be compiled as a
	  module.

8
menuconfig NEW_LEDS
R
Richard Purdie 已提交
9 10
	bool "LED Support"
	help
11 12 13 14 15
	  Say Y to enable Linux LED support.  This allows control of supported
	  LEDs from both userspace and optionally, by kernel events (triggers).

	  This is not related to standard keyboard LEDs which are controlled
	  via the input system.
R
Richard Purdie 已提交
16

17 18
if NEW_LEDS

R
Richard Purdie 已提交
19
config LEDS_CLASS
20
	tristate "LED Class Support"
R
Richard Purdie 已提交
21 22 23 24
	help
	  This option enables the led sysfs class in /sys/class/leds.  You'll
	  need this to do anything useful with LEDs.  If unsure, say N.

B
Ben Dooks 已提交
25
comment "LED drivers"
26

H
Haojian Zhuang 已提交
27 28
config LEDS_88PM860X
	tristate "LED Support for Marvell 88PM860x PMIC"
J
Johannes Berg 已提交
29
	depends on LEDS_CLASS
R
Richard Purdie 已提交
30
	depends on MFD_88PM860X
H
Haojian Zhuang 已提交
31 32 33 34
	help
	  This option enables support for on-chip LED drivers found on Marvell
	  Semiconductor 88PM8606 PMIC.

D
David Brownell 已提交
35 36
config LEDS_ATMEL_PWM
	tristate "LED Support using Atmel PWM outputs"
J
Johannes Berg 已提交
37
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
38
	depends on ATMEL_PWM
D
David Brownell 已提交
39 40 41 42
	help
	  This option enables support for LEDs driven using outputs
	  of the dedicated PWM controller found on newer Atmel SOCs.

43 44 45 46 47 48 49 50 51 52
config LEDS_LM3530
	tristate "LCD Backlight driver for LM3530"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the LCD backlight using
	  LM3530 ambient light sensor chip. This ALS chip can be
	  controlled manually or using PWM input or using ambient
	  light automatically.

J
Johan Hovold 已提交
53 54 55 56 57 58 59 60 61 62 63 64 65
config LEDS_LM3533
	tristate "LED support for LM3533"
	depends on LEDS_CLASS
	depends on MFD_LM3533
	help
	  This option enables support for the LEDs on National Semiconductor /
	  TI LM3533 Lighting Power chips.

	  The LEDs can be controlled directly, through PWM input, or by the
	  ambient-light-sensor interface. The chip supports
	  hardware-accelerated blinking with maximum on and off periods of 9.8
	  and 77 seconds respectively.

66 67
config LEDS_LOCOMO
	tristate "LED Support for Locomo device"
J
Johannes Berg 已提交
68
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
69
	depends on SHARP_LOCOMO
70 71 72 73
	help
	  This option enables support for the LEDs on Sharp Locomo.
	  Zaurus models SL-5500 and SL-5600.

74 75
config LEDS_MIKROTIK_RB532
	tristate "LED Support for Mikrotik Routerboard 532"
J
Johannes Berg 已提交
76
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
77
	depends on MIKROTIK_RB532
78 79 80 81
	help
	  This option enables support for the so called "User LED" of
	  Mikrotik's Routerboard 532.

B
Ben Dooks 已提交
82 83
config LEDS_S3C24XX
	tristate "LED Support for Samsung S3C24XX GPIO LEDs"
J
Johannes Berg 已提交
84
	depends on LEDS_CLASS
85
	depends on ARCH_S3C24XX
B
Ben Dooks 已提交
86 87 88 89
	help
	  This option enables support for LEDs connected to GPIO lines
	  on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.

90 91
config LEDS_NET48XX
	tristate "LED Support for Soekris net48xx series Error LED"
J
Johannes Berg 已提交
92
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
93
	depends on SCx200_GPIO
94 95 96 97
	help
	  This option enables support for the Soekris net4801 and net4826 error
	  LED.

98 99
config LEDS_FSG
	tristate "LED Support for the Freecom FSG-3"
J
Johannes Berg 已提交
100
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
101
	depends on MACH_FSG
102 103 104
	help
	  This option enables support for the LEDs on the Freecom FSG-3.

105 106
config LEDS_WRAP
	tristate "LED Support for the WRAP series LEDs"
J
Johannes Berg 已提交
107
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
108
	depends on SCx200_GPIO
109 110 111
	help
	  This option enables support for the PCEngines WRAP programmable LEDs.

Y
Yoichi Yuasa 已提交
112 113
config LEDS_COBALT_QUBE
	tristate "LED Support for the Cobalt Qube series front LED"
J
Johannes Berg 已提交
114
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
115
	depends on MIPS_COBALT
116
	help
Y
Yoichi Yuasa 已提交
117
	  This option enables support for the front LED on Cobalt Qube series
118

119 120
config LEDS_COBALT_RAQ
	bool "LED Support for the Cobalt Raq series"
121
	depends on LEDS_CLASS=y && MIPS_COBALT
122 123 124 125
	select LEDS_TRIGGERS
	help
	  This option enables support for the Cobalt Raq series LEDs.

126 127
config LEDS_SUNFIRE
	tristate "LED support for SunFire servers."
J
Johannes Berg 已提交
128
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
129
	depends on SPARC64
130 131 132 133 134
	select LEDS_TRIGGERS
	help
	  This option enables support for the Left, Middle, and Right
	  LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.

135 136
config LEDS_HP6XX
	tristate "LED Support for the HP Jornada 6xx"
J
Johannes Berg 已提交
137
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
138
	depends on SH_HP6XX
139
	help
140
	  This option enables LED support for the handheld
141 142
	  HP Jornada 620/660/680/690.

R
Riku Voipio 已提交
143 144
config LEDS_PCA9532
	tristate "LED driver for PCA9532 dimmer"
J
Johannes Berg 已提交
145
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
146
	depends on I2C && INPUT && EXPERIMENTAL
R
Riku Voipio 已提交
147 148
	help
	  This option enables support for NXP pca9532
149
	  LED controller. It is generally only useful
R
Riku Voipio 已提交
150 151
	  as a platform driver

152 153 154 155 156 157 158 159 160 161
config LEDS_PCA9532_GPIO
	bool "Enable GPIO support for PCA9532"
	depends on LEDS_PCA9532
	depends on GPIOLIB
	help
	  Allow unused pins on PCA9532 to be used as gpio.

	  To use a pin as gpio pca9532_type in pca9532_platform data needs to
	  set to PCA9532_TYPE_GPIO.

162 163
config LEDS_GPIO
	tristate "LED Support for GPIO connected LEDs"
J
Johannes Berg 已提交
164
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
165
	depends on GENERIC_GPIO
166 167 168
	help
	  This option enables support for the LEDs connected to GPIO
	  outputs. To be useful the particular board must have LEDs
169 170 171 172
	  and they must be connected to the GPIO lines.  The LEDs must be
	  defined as platform devices and/or OpenFirmware platform devices.
	  The code to use these bindings can be selected below.

173 174
config LEDS_LP3944
	tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
J
Johannes Berg 已提交
175
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
176
	depends on I2C
177
	help
178 179 180
	  This option enables support for LEDs connected to the National
	  Semiconductor LP3944 Lighting Management Unit (LMU) also known as
	  Fun Light Chip.
181 182 183 184

	  To compile this driver as a module, choose M here: the
	  module will be called leds-lp3944.

185 186 187 188 189 190 191 192 193 194
config LEDS_LP5521
	tristate "LED Support for N.S. LP5521 LED driver chip"
	depends on LEDS_CLASS && I2C
	help
	  If you say yes here you get support for the National Semiconductor
	  LP5521 LED driver. It is 3 channel chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.

config LEDS_LP5523
195
	tristate "LED Support for TI/National LP5523/55231 LED driver chip"
196 197
	depends on LEDS_CLASS && I2C
	help
198 199 200
	  If you say yes here you get support for TI/National Semiconductor
	  LP5523/55231 LED driver.
	  It is 9 channel chip with programmable engines.
201 202 203
	  Driver provides direct control via LED class and interface for
	  programming the engines.

K
Kim, Milo 已提交
204 205 206 207 208 209 210
config LEDS_LP8788
	tristate "LED support for the TI LP8788 PMIC"
	depends on LEDS_CLASS
	depends on MFD_LP8788
	help
	  This option enables support for the Keyboard LEDs on the LP8788 PMIC.

211
config LEDS_CLEVO_MAIL
212
	tristate "Mail LED on Clevo notebook"
J
Johannes Berg 已提交
213
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
214
	depends on X86 && SERIO_I8042 && DMI
215 216 217 218 219
	help
	  This driver makes the mail LED accessible from userspace
	  programs through the leds subsystem. This LED have three
	  known mode: off, blink at 0.5Hz and blink at 1Hz.

220 221 222 223 224
	  The driver supports two kinds of interface: using ledtrig-timer
	  or through /sys/class/leds/clevo::mail/brightness. As this LED
	  cannot change it's brightness it blinks instead. The brightness
	  value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
	  blink at 1Hz.
225 226 227

	  This module can drive the mail LED for the following notebooks:

228
	  	Clevo D400P
229 230 231 232 233 234 235
	  	Clevo D410J
	  	Clevo D410V
	  	Clevo D400V/D470V (not tested, but might work)
	  	Clevo M540N
	  	Clevo M5x0N (not tested, but might work)
	  	Positivo Mobile (Clevo M5x0V)

236
	  If your model is not listed here you can try the "nodetect"
237
	  module parameter.
238

239 240 241
	  To compile this driver as a module, choose M here: the
	  module will be called leds-clevo-mail.

242 243
config LEDS_PCA955X
	tristate "LED Support for PCA955x I2C chips"
J
Johannes Berg 已提交
244
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
245
	depends on I2C
246 247 248 249 250
	help
	  This option enables support for LEDs connected to PCA955x
	  LED driver chips accessed via the I2C bus.  Supported
	  devices include PCA9550, PCA9551, PCA9552, and PCA9553.

251 252 253 254 255 256 257 258
config LEDS_PCA9633
	tristate "LED support for PCA9633 I2C chip"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for LEDs connected to the PCA9633
	  LED driver chip accessed via the I2C bus.

M
Mark Brown 已提交
259 260
config LEDS_WM831X_STATUS
	tristate "LED support for status LEDs on WM831x PMICs"
J
Johannes Berg 已提交
261
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
262
	depends on MFD_WM831X
M
Mark Brown 已提交
263 264 265 266
	help
	  This option enables support for the status LEDs of the WM831x
          series of PMICs.

M
Mark Brown 已提交
267 268
config LEDS_WM8350
	tristate "LED Support for WM8350 AudioPlus PMIC"
J
Johannes Berg 已提交
269
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
270
	depends on MFD_WM8350
M
Mark Brown 已提交
271 272 273 274
	help
	  This option enables support for LEDs driven by the Wolfson
	  Microelectronics WM8350 AudioPlus PMIC.

275 276
config LEDS_DA903X
	tristate "LED Support for DA9030/DA9034 PMIC"
J
Johannes Berg 已提交
277
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
278
	depends on PMIC_DA903X
279 280 281 282
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9030/DA9034 PMICs.

283 284 285 286 287 288 289 290
config LEDS_DA9052
	tristate "Dialog DA9052/DA9053 LEDS"
	depends on LEDS_CLASS
	depends on PMIC_DA9052
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.

291 292
config LEDS_DAC124S085
	tristate "LED Support for DAC124S085 SPI DAC"
J
Johannes Berg 已提交
293
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
294
	depends on SPI
295 296 297 298
	help
	  This option enables support for DAC124S085 SPI DAC from NatSemi,
	  which can be used to control up to four LEDs.

299 300
config LEDS_PWM
	tristate "PWM driven LED Support"
J
Johannes Berg 已提交
301
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
302
	depends on HAVE_PWM
303 304 305
	help
	  This option enables support for pwm driven LEDs

306 307
config LEDS_REGULATOR
	tristate "REGULATOR driven LED support"
J
Johannes Berg 已提交
308
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
309
	depends on REGULATOR
310 311 312
	help
	  This option enables support for regulator driven LEDs.

K
Kim Kyuwon 已提交
313 314
config LEDS_BD2802
	tristate "LED driver for BD2802 RGB LED"
J
Johannes Berg 已提交
315
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
316
	depends on I2C
K
Kim Kyuwon 已提交
317 318 319 320
	help
	  This option enables support for BD2802GU RGB LED driver chips
	  accessed via the I2C bus.

321 322
config LEDS_INTEL_SS4200
	tristate "LED driver for Intel NAS SS4200 series"
J
Johannes Berg 已提交
323
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
324
	depends on PCI && DMI
325 326 327 328 329 330
	help
	  This option enables support for the Intel SS4200 series of
	  Network Attached Storage servers.  You may control the hard
	  drive or power LEDs on the front panel.  Using this driver
	  can stop the front LED from blinking after startup.

331 332
config LEDS_LT3593
	tristate "LED driver for LT3593 controllers"
J
Johannes Berg 已提交
333
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
334
	depends on GENERIC_GPIO
335 336 337 338 339
	help
	  This option enables support for LEDs driven by a Linear Technology
	  LT3593 controller. This controller uses a special one-wire pulse
	  coding protocol to set the brightness.

340 341
config LEDS_ADP5520
	tristate "LED Support for ADP5520/ADP5501 PMIC"
J
Johannes Berg 已提交
342
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
343
	depends on PMIC_ADP5520
344 345 346 347 348 349 350
	help
	  This option enables support for on-chip LED drivers found
	  on Analog Devices ADP5520/ADP5501 PMICs.

	  To compile this driver as a module, choose M here: the module will
	  be called leds-adp5520.

351 352
config LEDS_DELL_NETBOOKS
	tristate "External LED on Dell Business Netbooks"
J
Johannes Berg 已提交
353
	depends on LEDS_CLASS
354 355 356 357 358
	depends on X86 && ACPI_WMI
	help
	  This adds support for the Latitude 2100 and similar
	  notebooks that have an external LED.

359 360
config LEDS_MC13783
	tristate "LED Support for MC13783 PMIC"
J
Johannes Berg 已提交
361
	depends on LEDS_CLASS
362 363 364 365 366
	depends on MFD_MC13783
	help
	  This option enable support for on-chip LED drivers found
	  on Freescale Semiconductor MC13783 PMIC.

367 368
config LEDS_NS2
	tristate "LED support for Network Space v2 GPIO LEDs"
J
Johannes Berg 已提交
369
	depends on LEDS_CLASS
P
Paul Bolle 已提交
370 371
	depends on MACH_NETSPACE_V2 || MACH_INETSPACE_V2 || \
		   MACH_NETSPACE_MAX_V2 || MACH_D2NET_V2
372 373 374 375 376 377
	default y
	help
	  This option enable support for the dual-GPIO LED found on the
	  Network Space v2 board (and parents). This include Internet Space v2,
	  Network Space (Max) v2 and d2 Network v2 boards.

378 379 380
config LEDS_NETXBIG
	tristate "LED support for Big Network series LEDs"
	depends on MACH_NET2BIG_V2 || MACH_NET5BIG_V2
381
	depends on LEDS_CLASS
382 383 384 385 386 387
	default y
	help
	  This option enable support for LEDs found on the LaCie 2Big
	  and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
	  controlled through a GPIO extension bus.

P
Paul Parsons 已提交
388 389
config LEDS_ASIC3
	bool "LED support for the HTC ASIC3"
390
	depends on LEDS_CLASS=y
P
Paul Parsons 已提交
391 392 393 394 395 396 397 398
	depends on MFD_ASIC3
	default y
	help
	  This option enables support for the LEDs on the HTC ASIC3. The HTC
	  ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
	  cannot be used. This driver supports hardware blinking with an on+off
	  period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.

M
Magnus Damm 已提交
399 400
config LEDS_RENESAS_TPU
	bool "LED support for Renesas TPU"
401
	depends on LEDS_CLASS=y && HAVE_CLK && GENERIC_GPIO
M
Magnus Damm 已提交
402 403 404 405 406 407 408 409 410
	help
	  This option enables build of the LED TPU platform driver,
	  suitable to drive any TPU channel on newer Renesas SoCs.
	  The driver controls the GPIO pin connected to the LED via
	  the GPIO framework and expects the LED to be connected to
	  a pin that can be driven in both GPIO mode and using TPU
	  pin function. The latter to support brightness control.
	  Brightness control is supported but hardware blinking is not.

411 412 413 414 415 416 417 418
config LEDS_TCA6507
	tristate "LED Support for TCA6507 I2C chip"
	depends on LEDS_CLASS && I2C
	help
	  This option enables support for LEDs connected to TC6507
	  LED driver chips accessed via the I2C bus.
	  Driver support brightness control and hardware-assisted blinking.

419 420 421 422 423 424 425
config LEDS_MAX8997
	tristate "LED support for MAX8997 PMIC"
	depends on LEDS_CLASS && MFD_MAX8997
	help
	  This option enables support for on-chip LED drivers on
	  MAXIM MAX8997 PMIC.

426 427 428 429 430 431 432 433
config LEDS_LM3556
	tristate "LED support for LM3556 Chip"
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
	  This option enables support for LEDs connected to LM3556.
	  LM3556 includes Torch, Flash and Indicator functions.

434 435 436 437 438 439 440
config LEDS_OT200
	tristate "LED support for the Bachmann OT200"
	depends on LEDS_CLASS && HAS_IOMEM
	help
	  This option enables support for the LEDs on the Bachmann OT200.
	  Say Y to enable LEDs on the Bachmann OT200.

441 442 443 444 445 446 447 448
config LEDS_BLINKM
	tristate "LED support for the BlinkM I2C RGB LED"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the BlinkM RGB LED connected
	  through I2C. Say Y to enable support for the BlinkM LED.

B
Ben Dooks 已提交
449 450
config LEDS_TRIGGERS
	bool "LED Trigger support"
J
Johannes Berg 已提交
451
	depends on LEDS_CLASS
B
Ben Dooks 已提交
452 453 454 455 456
	help
	  This option enables trigger support for the leds class.
	  These triggers allow kernel events to drive the LEDs and can
	  be configured via sysfs. If unsure, say Y.

H
H Hartley Sweeten 已提交
457 458
comment "LED Triggers"

459 460
config LEDS_TRIGGER_TIMER
	tristate "LED Timer Trigger"
J
Johannes Berg 已提交
461
	depends on LEDS_TRIGGERS
462 463
	help
	  This allows LEDs to be controlled by a programmable timer
464 465
	  via sysfs. Some LED hardware can be programmed to start
	  blinking the LED without any further software interaction.
P
Paul Bolle 已提交
466
	  For more details read Documentation/leds/leds-class.txt.
467 468

	  If unsure, say Y.
469

F
Fabio Baltieri 已提交
470 471 472 473 474 475 476 477 478 479 480 481 482 483
config LEDS_TRIGGER_ONESHOT
	tristate "LED One-shot Trigger"
	depends on LEDS_TRIGGERS
	help
	  This allows LEDs to blink in one-shot pulses with parameters
	  controlled via sysfs.  It's useful to notify the user on
	  sporadic events, when there are no clear begin and end trap points,
	  or on dense events, where this blinks the LED at constant rate if
	  rearmed continuously.

	  It also shows how to use the led_blink_set_oneshot() function.

	  If unsure, say Y.

484
config LEDS_TRIGGER_IDE_DISK
485
	bool "LED IDE Disk Trigger"
H
H Hartley Sweeten 已提交
486
	depends on IDE_GD_ATA
J
Johannes Berg 已提交
487
	depends on LEDS_TRIGGERS
488 489 490 491
	help
	  This allows LEDs to be controlled by IDE disk activity.
	  If unsure, say Y.

492 493
config LEDS_TRIGGER_HEARTBEAT
	tristate "LED Heartbeat Trigger"
J
Johannes Berg 已提交
494
	depends on LEDS_TRIGGERS
495 496 497 498 499 500
	help
	  This allows LEDs to be controlled by a CPU load average.
	  The flash frequency is a hyperbolic function of the 1-minute
	  load average.
	  If unsure, say Y.

R
Rodolfo Giometti 已提交
501 502
config LEDS_TRIGGER_BACKLIGHT
	tristate "LED backlight Trigger"
J
Johannes Berg 已提交
503
	depends on LEDS_TRIGGERS
R
Rodolfo Giometti 已提交
504 505 506 507 508 509
	help
	  This allows LEDs to be controlled as a backlight device: they
	  turn off and on when the display is blanked and unblanked.

	  If unsure, say N.

F
Felipe Balbi 已提交
510 511
config LEDS_TRIGGER_GPIO
	tristate "LED GPIO Trigger"
J
Johannes Berg 已提交
512
	depends on LEDS_TRIGGERS
F
Felipe Balbi 已提交
513 514 515 516 517 518 519 520 521 522
	depends on GPIOLIB
	help
	  This allows LEDs to be controlled by gpio events. It's good
	  when using gpios as switches and triggering the needed LEDs
	  from there. One use case is n810's keypad LEDs that could
	  be triggered by this trigger when user slides up to show
	  keypad.

	  If unsure, say N.

N
Nick Forbes 已提交
523 524
config LEDS_TRIGGER_DEFAULT_ON
	tristate "LED Default ON Trigger"
J
Johannes Berg 已提交
525
	depends on LEDS_TRIGGERS
N
Nick Forbes 已提交
526 527 528 529
	help
	  This allows LEDs to be initialised in the ON state.
	  If unsure, say Y.

530 531 532
comment "iptables trigger is under Netfilter config (LED target)"
	depends on LEDS_TRIGGERS

533 534 535 536 537
config LEDS_TRIGGER_TRANSIENT
	tristate "LED Transient Trigger"
	depends on LEDS_TRIGGERS
	help
	  This allows one time activation of a transient state on
538
	  GPIO/PWM based hardware.
539 540
	  If unsure, say Y.

541
endif # NEW_LEDS