qlge_main.c

/*
 * QLogic qlge NIC HBA Driver
 * Copyright (c)  2003-2008 QLogic Corporation
 * See LICENSE.qlge for copyright and licensing details.
 * Author:     Linux qlge network device driver by
 *                      Ron Mercer <ron.mercer@qlogic.com>
 */
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/types.h>
#include <linux/module.h>
#include <linux/list.h>
#include <linux/pci.h>
#include <linux/dma-mapping.h>
#include <linux/pagemap.h>
#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/dmapool.h>
#include <linux/mempool.h>
#include <linux/spinlock.h>
#include <linux/kthread.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
#include <linux/ioport.h>
#include <linux/in.h>
#include <linux/ip.h>
#include <linux/ipv6.h>
#include <net/ipv6.h>
#include <linux/tcp.h>
#include <linux/udp.h>
#include <linux/if_arp.h>
#include <linux/if_ether.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/ethtool.h>
#include <linux/skbuff.h>
#include <linux/if_vlan.h>
#include <linux/delay.h>
#include <linux/mm.h>
#include <linux/vmalloc.h>
#include <net/ip6_checksum.h>

#include "qlge.h"

char qlge_driver_name[] = DRV_NAME;
const char qlge_driver_version[] = DRV_VERSION;

MODULE_AUTHOR("Ron Mercer <ron.mercer@qlogic.com>");
MODULE_DESCRIPTION(DRV_STRING " ");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);

static const u32 default_msg =
    NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK |
/* NETIF_MSG_TIMER |	*/
    NETIF_MSG_IFDOWN |
    NETIF_MSG_IFUP |
    NETIF_MSG_RX_ERR |
    NETIF_MSG_TX_ERR |
/*  NETIF_MSG_TX_QUEUED | */
/*  NETIF_MSG_INTR | NETIF_MSG_TX_DONE | NETIF_MSG_RX_STATUS | */
/* NETIF_MSG_PKTDATA | */
    NETIF_MSG_HW | NETIF_MSG_WOL | 0;

static int debug = 0x00007fff;	/* defaults above */
module_param(debug, int, 0);
MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");

#define MSIX_IRQ 0
#define MSI_IRQ 1
#define LEG_IRQ 2
static int irq_type = MSIX_IRQ;
module_param(irq_type, int, MSIX_IRQ);
MODULE_PARM_DESC(irq_type, "0 = MSI-X, 1 = MSI, 2 = Legacy.");

static struct pci_device_id qlge_pci_tbl[] __devinitdata = {
	{PCI_DEVICE(PCI_VENDOR_ID_QLOGIC, QLGE_DEVICE_ID_8012)},
	{PCI_DEVICE(PCI_VENDOR_ID_QLOGIC, QLGE_DEVICE_ID_8000)},
	/* required last entry */
	{0,}
};

MODULE_DEVICE_TABLE(pci, qlge_pci_tbl);

/* This hardware semaphore causes exclusive access to
 * resources shared between the NIC driver, MPI firmware,
 * FCOE firmware and the FC driver.
 */
static int ql_sem_trylock(struct ql_adapter *qdev, u32 sem_mask)
{
	u32 sem_bits = 0;

	switch (sem_mask) {
	case SEM_XGMAC0_MASK:
		sem_bits = SEM_SET << SEM_XGMAC0_SHIFT;
		break;
	case SEM_XGMAC1_MASK:
		sem_bits = SEM_SET << SEM_XGMAC1_SHIFT;
		break;
	case SEM_ICB_MASK:
		sem_bits = SEM_SET << SEM_ICB_SHIFT;
		break;
	case SEM_MAC_ADDR_MASK:
		sem_bits = SEM_SET << SEM_MAC_ADDR_SHIFT;
		break;
	case SEM_FLASH_MASK:
		sem_bits = SEM_SET << SEM_FLASH_SHIFT;
		break;
	case SEM_PROBE_MASK:
		sem_bits = SEM_SET << SEM_PROBE_SHIFT;
		break;
	case SEM_RT_IDX_MASK:
		sem_bits = SEM_SET << SEM_RT_IDX_SHIFT;
		break;
	case SEM_PROC_REG_MASK:
		sem_bits = SEM_SET << SEM_PROC_REG_SHIFT;
		break;
	default:
		QPRINTK(qdev, PROBE, ALERT, "Bad Semaphore mask!.\n");
		return -EINVAL;
	}

	ql_write32(qdev, SEM, sem_bits | sem_mask);
	return !(ql_read32(qdev, SEM) & sem_bits);
}

int ql_sem_spinlock(struct ql_adapter *qdev, u32 sem_mask)
{
	unsigned int wait_count = 30;
	do {
		if (!ql_sem_trylock(qdev, sem_mask))
			return 0;
		udelay(100);
	} while (--wait_count);
	return -ETIMEDOUT;
}

void ql_sem_unlock(struct ql_adapter *qdev, u32 sem_mask)
{
	ql_write32(qdev, SEM, sem_mask);
	ql_read32(qdev, SEM);	/* flush */
}

/* This function waits for a specific bit to come ready
 * in a given register.  It is used mostly by the initialize
 * process, but is also used in kernel thread API such as
 * netdev->set_multi, netdev->set_mac_address, netdev->vlan_rx_add_vid.
 */
int ql_wait_reg_rdy(struct ql_adapter *qdev, u32 reg, u32 bit, u32 err_bit)
{
	u32 temp;
	int count = UDELAY_COUNT;

	while (count) {
		temp = ql_read32(qdev, reg);

		/* check for errors */
		if (temp & err_bit) {
			QPRINTK(qdev, PROBE, ALERT,
				"register 0x%.08x access error, value = 0x%.08x!.\n",
				reg, temp);
			return -EIO;
		} else if (temp & bit)
			return 0;
		udelay(UDELAY_DELAY);
		count--;
	}
	QPRINTK(qdev, PROBE, ALERT,
		"Timed out waiting for reg %x to come ready.\n", reg);
	return -ETIMEDOUT;
}

/* The CFG register is used to download TX and RX control blocks
 * to the chip. This function waits for an operation to complete.
 */
static int ql_wait_cfg(struct ql_adapter *qdev, u32 bit)
{
	int count = UDELAY_COUNT;
	u32 temp;

	while (count) {
		temp = ql_read32(qdev, CFG);
		if (temp & CFG_LE)
			return -EIO;
		if (!(temp & bit))
			return 0;
		udelay(UDELAY_DELAY);
		count--;
	}
	return -ETIMEDOUT;
}


/* Used to issue init control blocks to hw. Maps control block,
 * sets address, triggers download, waits for completion.
 */
int ql_write_cfg(struct ql_adapter *qdev, void *ptr, int size, u32 bit,
		 u16 q_id)
{
	u64 map;
	int status = 0;
	int direction;
	u32 mask;
	u32 value;

	direction =
	    (bit & (CFG_LRQ | CFG_LR | CFG_LCQ)) ? PCI_DMA_TODEVICE :
	    PCI_DMA_FROMDEVICE;

	map = pci_map_single(qdev->pdev, ptr, size, direction);
	if (pci_dma_mapping_error(qdev->pdev, map)) {
		QPRINTK(qdev, IFUP, ERR, "Couldn't map DMA area.\n");
		return -ENOMEM;
	}

	status = ql_sem_spinlock(qdev, SEM_ICB_MASK);
	if (status)
		return status;

	status = ql_wait_cfg(qdev, bit);
	if (status) {
		QPRINTK(qdev, IFUP, ERR,
			"Timed out waiting for CFG to come ready.\n");
		goto exit;
	}

	ql_write32(qdev, ICB_L, (u32) map);
	ql_write32(qdev, ICB_H, (u32) (map >> 32));

	mask = CFG_Q_MASK | (bit << 16);
	value = bit | (q_id << CFG_Q_SHIFT);
	ql_write32(qdev, CFG, (mask | value));

	/*
	 * Wait for the bit to clear after signaling hw.
	 */
	status = ql_wait_cfg(qdev, bit);
exit:
	ql_sem_unlock(qdev, SEM_ICB_MASK);	/* does flush too */
	pci_unmap_single(qdev->pdev, map, size, direction);
	return status;
}

/* Get a specific MAC address from the CAM.  Used for debug and reg dump. */
int ql_get_mac_addr_reg(struct ql_adapter *qdev, u32 type, u16 index,
			u32 *value)
{
	u32 offset = 0;
	int status;

	switch (type) {
	case MAC_ADDR_TYPE_MULTI_MAC:
	case MAC_ADDR_TYPE_CAM_MAC:
		{
			status =
			    ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MW, 0);
			if (status)
				goto exit;
			ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
				   (index << MAC_ADDR_IDX_SHIFT) | /* index */
				   MAC_ADDR_ADR | MAC_ADDR_RS | type); /* type */
			status =
			    ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MR, 0);
			if (status)
				goto exit;
			*value++ = ql_read32(qdev, MAC_ADDR_DATA);
			status =
			    ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MW, 0);
			if (status)
				goto exit;
			ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
				   (index << MAC_ADDR_IDX_SHIFT) | /* index */
				   MAC_ADDR_ADR | MAC_ADDR_RS | type); /* type */
			status =
			    ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MR, 0);
			if (status)
				goto exit;
			*value++ = ql_read32(qdev, MAC_ADDR_DATA);
			if (type == MAC_ADDR_TYPE_CAM_MAC) {
				status =
				    ql_wait_reg_rdy(qdev,
					MAC_ADDR_IDX, MAC_ADDR_MW, 0);
				if (status)
					goto exit;
				ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
					   (index << MAC_ADDR_IDX_SHIFT) | /* index */
					   MAC_ADDR_ADR | MAC_ADDR_RS | type); /* type */
				status =
				    ql_wait_reg_rdy(qdev, MAC_ADDR_IDX,
						    MAC_ADDR_MR, 0);
				if (status)
					goto exit;
				*value++ = ql_read32(qdev, MAC_ADDR_DATA);
			}
			break;
		}
	case MAC_ADDR_TYPE_VLAN:
	case MAC_ADDR_TYPE_MULTI_FLTR:
	default:
		QPRINTK(qdev, IFUP, CRIT,
			"Address type %d not yet supported.\n", type);
		status = -EPERM;
	}
exit:
	return status;
}

/* Set up a MAC, multicast or VLAN address for the
 * inbound frame matching.
 */
static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type,
			       u16 index)
{
	u32 offset = 0;
	int status = 0;

	switch (type) {
	case MAC_ADDR_TYPE_MULTI_MAC:
		{
			u32 upper = (addr[0] << 8) | addr[1];
			u32 lower = (addr[2] << 24) | (addr[3] << 16) |
					(addr[4] << 8) | (addr[5]);

			status =
				ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MW, 0);
			if (status)
				goto exit;
			ql_write32(qdev, MAC_ADDR_IDX, (offset++) |
				(index << MAC_ADDR_IDX_SHIFT) |
				type | MAC_ADDR_E);
			ql_write32(qdev, MAC_ADDR_DATA, lower);
			status =
				ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MW, 0);
			if (status)
				goto exit;
			ql_write32(qdev, MAC_ADDR_IDX, (offset++) |
				(index << MAC_ADDR_IDX_SHIFT) |
				type | MAC_ADDR_E);

			ql_write32(qdev, MAC_ADDR_DATA, upper);
			status =
				ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MW, 0);
			if (status)
				goto exit;
			break;
		}
	case MAC_ADDR_TYPE_CAM_MAC:
		{
			u32 cam_output;
			u32 upper = (addr[0] << 8) | addr[1];
			u32 lower =
			    (addr[2] << 24) | (addr[3] << 16) | (addr[4] << 8) |
			    (addr[5]);

			QPRINTK(qdev, IFUP, DEBUG,
				"Adding %s address %pM"
				" at index %d in the CAM.\n",
				((type ==
				  MAC_ADDR_TYPE_MULTI_MAC) ? "MULTICAST" :
				 "UNICAST"), addr, index);

			status =
			    ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MW, 0);
			if (status)
				goto exit;
			ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
				   (index << MAC_ADDR_IDX_SHIFT) | /* index */
				   type);	/* type */
			ql_write32(qdev, MAC_ADDR_DATA, lower);
			status =
			    ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MW, 0);
			if (status)
				goto exit;
			ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
				   (index << MAC_ADDR_IDX_SHIFT) | /* index */
				   type);	/* type */
			ql_write32(qdev, MAC_ADDR_DATA, upper);
			status =
			    ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MW, 0);
			if (status)
				goto exit;
			ql_write32(qdev, MAC_ADDR_IDX, (offset) |	/* offset */
				   (index << MAC_ADDR_IDX_SHIFT) |	/* index */
				   type);	/* type */
			/* This field should also include the queue id
			   and possibly the function id.  Right now we hardcode
			   the route field to NIC core.
			 */
			cam_output = (CAM_OUT_ROUTE_NIC |
				      (qdev->
				       func << CAM_OUT_FUNC_SHIFT) |
					(0 << CAM_OUT_CQ_ID_SHIFT));
			if (qdev->vlgrp)
				cam_output |= CAM_OUT_RV;
			/* route to NIC core */
			ql_write32(qdev, MAC_ADDR_DATA, cam_output);
			break;
		}
	case MAC_ADDR_TYPE_VLAN:
		{
			u32 enable_bit = *((u32 *) &addr[0]);
			/* For VLAN, the addr actually holds a bit that
			 * either enables or disables the vlan id we are
			 * addressing. It's either MAC_ADDR_E on or off.
			 * That's bit-27 we're talking about.
			 */
			QPRINTK(qdev, IFUP, INFO, "%s VLAN ID %d %s the CAM.\n",
				(enable_bit ? "Adding" : "Removing"),
				index, (enable_bit ? "to" : "from"));

			status =
			    ql_wait_reg_rdy(qdev,
				MAC_ADDR_IDX, MAC_ADDR_MW, 0);
			if (status)
				goto exit;
			ql_write32(qdev, MAC_ADDR_IDX, offset |	/* offset */
				   (index << MAC_ADDR_IDX_SHIFT) |	/* index */
				   type |	/* type */
				   enable_bit);	/* enable/disable */
			break;
		}
	case MAC_ADDR_TYPE_MULTI_FLTR:
	default:
		QPRINTK(qdev, IFUP, CRIT,
			"Address type %d not yet supported.\n", type);
		status = -EPERM;
	}
exit:
	return status;
}

/* Set or clear MAC address in hardware. We sometimes
 * have to clear it to prevent wrong frame routing
 * especially in a bonding environment.
 */
static int ql_set_mac_addr(struct ql_adapter *qdev, int set)
{
	int status;
	char zero_mac_addr[ETH_ALEN];
	char *addr;

	if (set) {
		addr = &qdev->ndev->dev_addr[0];
		QPRINTK(qdev, IFUP, DEBUG,
			"Set Mac addr %02x:%02x:%02x:%02x:%02x:%02x\n",
			addr[0], addr[1], addr[2], addr[3],
			addr[4], addr[5]);
	} else {
		memset(zero_mac_addr, 0, ETH_ALEN);
		addr = &zero_mac_addr[0];
		QPRINTK(qdev, IFUP, DEBUG,
				"Clearing MAC address on %s\n",
				qdev->ndev->name);
	}
	status = ql_sem_spinlock(qdev, SEM_MAC_ADDR_MASK);
	if (status)
		return status;
	status = ql_set_mac_addr_reg(qdev, (u8 *) addr,
			MAC_ADDR_TYPE_CAM_MAC, qdev->func * MAX_CQ);
	ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK);
	if (status)
		QPRINTK(qdev, IFUP, ERR, "Failed to init mac "
			"address.\n");
	return status;
}

void ql_link_on(struct ql_adapter *qdev)
{
	QPRINTK(qdev, LINK, ERR, "%s: Link is up.\n",
				 qdev->ndev->name);
	netif_carrier_on(qdev->ndev);
	ql_set_mac_addr(qdev, 1);
}

void ql_link_off(struct ql_adapter *qdev)
{
	QPRINTK(qdev, LINK, ERR, "%s: Link is down.\n",
				 qdev->ndev->name);
	netif_carrier_off(qdev->ndev);
	ql_set_mac_addr(qdev, 0);
}

/* Get a specific frame routing value from the CAM.
 * Used for debug and reg dump.
 */
int ql_get_routing_reg(struct ql_adapter *qdev, u32 index, u32 *value)
{
	int status = 0;

	status = ql_wait_reg_rdy(qdev, RT_IDX, RT_IDX_MW, 0);
	if (status)
		goto exit;

	ql_write32(qdev, RT_IDX,
		   RT_IDX_TYPE_NICQ | RT_IDX_RS | (index << RT_IDX_IDX_SHIFT));
	status = ql_wait_reg_rdy(qdev, RT_IDX, RT_IDX_MR, 0);
	if (status)
		goto exit;
	*value = ql_read32(qdev, RT_DATA);
exit:
	return status;
}

/* The NIC function for this chip has 16 routing indexes.  Each one can be used
 * to route different frame types to various inbound queues.  We send broadcast/
 * multicast/error frames to the default queue for slow handling,
 * and CAM hit/RSS frames to the fast handling queues.
 */
static int ql_set_routing_reg(struct ql_adapter *qdev, u32 index, u32 mask,
			      int enable)
{
	int status = -EINVAL; /* Return error if no mask match. */
	u32 value = 0;

	QPRINTK(qdev, IFUP, DEBUG,
		"%s %s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s mask %s the routing reg.\n",
		(enable ? "Adding" : "Removing"),
		((index == RT_IDX_ALL_ERR_SLOT) ? "MAC ERROR/ALL ERROR" : ""),
		((index == RT_IDX_IP_CSUM_ERR_SLOT) ? "IP CSUM ERROR" : ""),
		((index ==
		  RT_IDX_TCP_UDP_CSUM_ERR_SLOT) ? "TCP/UDP CSUM ERROR" : ""),
		((index == RT_IDX_BCAST_SLOT) ? "BROADCAST" : ""),
		((index == RT_IDX_MCAST_MATCH_SLOT) ? "MULTICAST MATCH" : ""),
		((index == RT_IDX_ALLMULTI_SLOT) ? "ALL MULTICAST MATCH" : ""),
		((index == RT_IDX_UNUSED6_SLOT) ? "UNUSED6" : ""),
		((index == RT_IDX_UNUSED7_SLOT) ? "UNUSED7" : ""),
		((index == RT_IDX_RSS_MATCH_SLOT) ? "RSS ALL/IPV4 MATCH" : ""),
		((index == RT_IDX_RSS_IPV6_SLOT) ? "RSS IPV6" : ""),
		((index == RT_IDX_RSS_TCP4_SLOT) ? "RSS TCP4" : ""),
		((index == RT_IDX_RSS_TCP6_SLOT) ? "RSS TCP6" : ""),
		((index == RT_IDX_CAM_HIT_SLOT) ? "CAM HIT" : ""),
		((index == RT_IDX_UNUSED013) ? "UNUSED13" : ""),
		((index == RT_IDX_UNUSED014) ? "UNUSED14" : ""),
		((index == RT_IDX_PROMISCUOUS_SLOT) ? "PROMISCUOUS" : ""),
		(enable ? "to" : "from"));

	switch (mask) {
	case RT_IDX_CAM_HIT:
		{
			value = RT_IDX_DST_CAM_Q |	/* dest */
			    RT_IDX_TYPE_NICQ |	/* type */
			    (RT_IDX_CAM_HIT_SLOT << RT_IDX_IDX_SHIFT);/* index */
			break;
		}
	case RT_IDX_VALID:	/* Promiscuous Mode frames. */
		{
			value = RT_IDX_DST_DFLT_Q |	/* dest */
			    RT_IDX_TYPE_NICQ |	/* type */
			    (RT_IDX_PROMISCUOUS_SLOT << RT_IDX_IDX_SHIFT);/* index */
			break;
		}
	case RT_IDX_ERR:	/* Pass up MAC,IP,TCP/UDP error frames. */
		{
			value = RT_IDX_DST_DFLT_Q |	/* dest */
			    RT_IDX_TYPE_NICQ |	/* type */
			    (RT_IDX_ALL_ERR_SLOT << RT_IDX_IDX_SHIFT);/* index */
			break;
		}
	case RT_IDX_BCAST:	/* Pass up Broadcast frames to default Q. */
		{
			value = RT_IDX_DST_DFLT_Q |	/* dest */
			    RT_IDX_TYPE_NICQ |	/* type */
			    (RT_IDX_BCAST_SLOT << RT_IDX_IDX_SHIFT);/* index */
			break;
		}
	case RT_IDX_MCAST:	/* Pass up All Multicast frames. */
		{
			value = RT_IDX_DST_DFLT_Q |	/* dest */
			    RT_IDX_TYPE_NICQ |	/* type */
			    (RT_IDX_ALLMULTI_SLOT << RT_IDX_IDX_SHIFT);/* index */
			break;
		}
	case RT_IDX_MCAST_MATCH:	/* Pass up matched Multicast frames. */
		{
			value = RT_IDX_DST_DFLT_Q |	/* dest */
			    RT_IDX_TYPE_NICQ |	/* type */
			    (RT_IDX_MCAST_MATCH_SLOT << RT_IDX_IDX_SHIFT);/* index */
			break;
		}
	case RT_IDX_RSS_MATCH:	/* Pass up matched RSS frames. */
		{
			value = RT_IDX_DST_RSS |	/* dest */
			    RT_IDX_TYPE_NICQ |	/* type */
			    (RT_IDX_RSS_MATCH_SLOT << RT_IDX_IDX_SHIFT);/* index */
			break;
		}
	case 0:		/* Clear the E-bit on an entry. */
		{
			value = RT_IDX_DST_DFLT_Q |	/* dest */
			    RT_IDX_TYPE_NICQ |	/* type */
			    (index << RT_IDX_IDX_SHIFT);/* index */
			break;
		}
	default:
		QPRINTK(qdev, IFUP, ERR, "Mask type %d not yet supported.\n",
			mask);
		status = -EPERM;
		goto exit;
	}

	if (value) {
		status = ql_wait_reg_rdy(qdev, RT_IDX, RT_IDX_MW, 0);
		if (status)
			goto exit;
		value |= (enable ? RT_IDX_E : 0);
		ql_write32(qdev, RT_IDX, value);
		ql_write32(qdev, RT_DATA, enable ? mask : 0);
	}
exit:
	return status;
}

static void ql_enable_interrupts(struct ql_adapter *qdev)
{
	ql_write32(qdev, INTR_EN, (INTR_EN_EI << 16) | INTR_EN_EI);
}

static void ql_disable_interrupts(struct ql_adapter *qdev)
{
	ql_write32(qdev, INTR_EN, (INTR_EN_EI << 16));
}

/* If we're running with multiple MSI-X vectors then we enable on the fly.
 * Otherwise, we may have multiple outstanding workers and don't want to
 * enable until the last one finishes. In this case, the irq_cnt gets
 * incremented everytime we queue a worker and decremented everytime
 * a worker finishes.  Once it hits zero we enable the interrupt.
 */
u32 ql_enable_completion_interrupt(struct ql_adapter *qdev, u32 intr)
{
	u32 var = 0;
	unsigned long hw_flags = 0;
	struct intr_context *ctx = qdev->intr_context + intr;

	if (likely(test_bit(QL_MSIX_ENABLED, &qdev->flags) && intr)) {
		/* Always enable if we're MSIX multi interrupts and
		 * it's not the default (zeroeth) interrupt.
		 */
		ql_write32(qdev, INTR_EN,
			   ctx->intr_en_mask);
		var = ql_read32(qdev, STS);
		return var;
	}

	spin_lock_irqsave(&qdev->hw_lock, hw_flags);
	if (atomic_dec_and_test(&ctx->irq_cnt)) {
		ql_write32(qdev, INTR_EN,
			   ctx->intr_en_mask);
		var = ql_read32(qdev, STS);
	}
	spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
	return var;
}

static u32 ql_disable_completion_interrupt(struct ql_adapter *qdev, u32 intr)
{
	u32 var = 0;
	struct intr_context *ctx;

	/* HW disables for us if we're MSIX multi interrupts and
	 * it's not the default (zeroeth) interrupt.
	 */
	if (likely(test_bit(QL_MSIX_ENABLED, &qdev->flags) && intr))
		return 0;

	ctx = qdev->intr_context + intr;
	spin_lock(&qdev->hw_lock);
	if (!atomic_read(&ctx->irq_cnt)) {
		ql_write32(qdev, INTR_EN,
		ctx->intr_dis_mask);
		var = ql_read32(qdev, STS);
	}
	atomic_inc(&ctx->irq_cnt);
	spin_unlock(&qdev->hw_lock);
	return var;
}

static void ql_enable_all_completion_interrupts(struct ql_adapter *qdev)
{
	int i;
	for (i = 0; i < qdev->intr_count; i++) {
		/* The enable call does a atomic_dec_and_test
		 * and enables only if the result is zero.
		 * So we precharge it here.
		 */
		if (unlikely(!test_bit(QL_MSIX_ENABLED, &qdev->flags) ||
			i == 0))
			atomic_set(&qdev->intr_context[i].irq_cnt, 1);
		ql_enable_completion_interrupt(qdev, i);
	}

}

static int ql_validate_flash(struct ql_adapter *qdev, u32 size, const char *str)
{
	int status, i;
	u16 csum = 0;
	__le16 *flash = (__le16 *)&qdev->flash;

	status = strncmp((char *)&qdev->flash, str, 4);
	if (status) {
		QPRINTK(qdev, IFUP, ERR, "Invalid flash signature.\n");
		return	status;
	}

	for (i = 0; i < size; i++)
		csum += le16_to_cpu(*flash++);

	if (csum)
		QPRINTK(qdev, IFUP, ERR,
			"Invalid flash checksum, csum = 0x%.04x.\n", csum);

	return csum;
}

static int ql_read_flash_word(struct ql_adapter *qdev, int offset, __le32 *data)
{
	int status = 0;
	/* wait for reg to come ready */
	status = ql_wait_reg_rdy(qdev,
			FLASH_ADDR, FLASH_ADDR_RDY, FLASH_ADDR_ERR);
	if (status)
		goto exit;
	/* set up for reg read */
	ql_write32(qdev, FLASH_ADDR, FLASH_ADDR_R | offset);
	/* wait for reg to come ready */
	status = ql_wait_reg_rdy(qdev,
			FLASH_ADDR, FLASH_ADDR_RDY, FLASH_ADDR_ERR);
	if (status)
		goto exit;
	 /* This data is stored on flash as an array of
	 * __le32.  Since ql_read32() returns cpu endian
	 * we need to swap it back.
	 */
	*data = cpu_to_le32(ql_read32(qdev, FLASH_DATA));
exit:
	return status;
}

static int ql_get_8000_flash_params(struct ql_adapter *qdev)
{
	u32 i, size;
	int status;
	__le32 *p = (__le32 *)&qdev->flash;
	u32 offset;
	u8 mac_addr[6];

	/* Get flash offset for function and adjust
	 * for dword access.
	 */
	if (!qdev->port)
		offset = FUNC0_FLASH_OFFSET / sizeof(u32);
	else
		offset = FUNC1_FLASH_OFFSET / sizeof(u32);

	if (ql_sem_spinlock(qdev, SEM_FLASH_MASK))
		return -ETIMEDOUT;

	size = sizeof(struct flash_params_8000) / sizeof(u32);
	for (i = 0; i < size; i++, p++) {
		status = ql_read_flash_word(qdev, i+offset, p);
		if (status) {
			QPRINTK(qdev, IFUP, ERR, "Error reading flash.\n");
			goto exit;
		}
	}

	status = ql_validate_flash(qdev,
			sizeof(struct flash_params_8000) / sizeof(u16),
			"8000");
	if (status) {
		QPRINTK(qdev, IFUP, ERR, "Invalid flash.\n");
		status = -EINVAL;
		goto exit;
	}

	/* Extract either manufacturer or BOFM modified
	 * MAC address.
	 */
	if (qdev->flash.flash_params_8000.data_type1 == 2)
		memcpy(mac_addr,
			qdev->flash.flash_params_8000.mac_addr1,
			qdev->ndev->addr_len);
	else
		memcpy(mac_addr,
			qdev->flash.flash_params_8000.mac_addr,
			qdev->ndev->addr_len);

	if (!is_valid_ether_addr(mac_addr)) {
		QPRINTK(qdev, IFUP, ERR, "Invalid MAC address.\n");
		status = -EINVAL;
		goto exit;
	}

	memcpy(qdev->ndev->dev_addr,
		mac_addr,
		qdev->ndev->addr_len);

exit:
	ql_sem_unlock(qdev, SEM_FLASH_MASK);
	return status;
}

static int ql_get_8012_flash_params(struct ql_adapter *qdev)
{
	int i;
	int status;
	__le32 *p = (__le32 *)&qdev->flash;
	u32 offset = 0;
	u32 size = sizeof(struct flash_params_8012) / sizeof(u32);

	/* Second function's parameters follow the first
	 * function's.
	 */
	if (qdev->port)
		offset = size;

	if (ql_sem_spinlock(qdev, SEM_FLASH_MASK))
		return -ETIMEDOUT;

	for (i = 0; i < size; i++, p++) {
		status = ql_read_flash_word(qdev, i+offset, p);
		if (status) {
			QPRINTK(qdev, IFUP, ERR, "Error reading flash.\n");
			goto exit;
		}

	}

	status = ql_validate_flash(qdev,
			sizeof(struct flash_params_8012) / sizeof(u16),
			"8012");
	if (status) {
		QPRINTK(qdev, IFUP, ERR, "Invalid flash.\n");
		status = -EINVAL;
		goto exit;
	}

	if (!is_valid_ether_addr(qdev->flash.flash_params_8012.mac_addr)) {
		status = -EINVAL;
		goto exit;
	}

	memcpy(qdev->ndev->dev_addr,
		qdev->flash.flash_params_8012.mac_addr,
		qdev->ndev->addr_len);

exit:
	ql_sem_unlock(qdev, SEM_FLASH_MASK);
	return status;
}

/* xgmac register are located behind the xgmac_addr and xgmac_data
 * register pair.  Each read/write requires us to wait for the ready
 * bit before reading/writing the data.
 */
static int ql_write_xgmac_reg(struct ql_adapter *qdev, u32 reg, u32 data)
{
	int status;
	/* wait for reg to come ready */
	status = ql_wait_reg_rdy(qdev,
			XGMAC_ADDR, XGMAC_ADDR_RDY, XGMAC_ADDR_XME);
	if (status)
		return status;
	/* write the data to the data reg */
	ql_write32(qdev, XGMAC_DATA, data);
	/* trigger the write */
	ql_write32(qdev, XGMAC_ADDR, reg);
	return status;
}

/* xgmac register are located behind the xgmac_addr and xgmac_data
 * register pair.  Each read/write requires us to wait for the ready
 * bit before reading/writing the data.
 */
int ql_read_xgmac_reg(struct ql_adapter *qdev, u32 reg, u32 *data)
{
	int status = 0;
	/* wait for reg to come ready */
	status = ql_wait_reg_rdy(qdev,
			XGMAC_ADDR, XGMAC_ADDR_RDY, XGMAC_ADDR_XME);
	if (status)
		goto exit;
	/* set up for reg read */
	ql_write32(qdev, XGMAC_ADDR, reg | XGMAC_ADDR_R);
	/* wait for reg to come ready */
	status = ql_wait_reg_rdy(qdev,
			XGMAC_ADDR, XGMAC_ADDR_RDY, XGMAC_ADDR_XME);
	if (status)
		goto exit;
	/* get the data */
	*data = ql_read32(qdev, XGMAC_DATA);
exit:
	return status;
}

/* This is used for reading the 64-bit statistics regs. */
int ql_read_xgmac_reg64(struct ql_adapter *qdev, u32 reg, u64 *data)
{
	int status = 0;
	u32 hi = 0;
	u32 lo = 0;

	status = ql_read_xgmac_reg(qdev, reg, &lo);
	if (status)
		goto exit;

	status = ql_read_xgmac_reg(qdev, reg + 4, &hi);
	if (status)
		goto exit;

	*data = (u64) lo | ((u64) hi << 32);

exit:
	return status;
}

static int ql_8000_port_initialize(struct ql_adapter *qdev)
{
	int status;
	/*
	 * Get MPI firmware version for driver banner
	 * and ethool info.
	 */
	status = ql_mb_about_fw(qdev);
	if (status)
		goto exit;
	status = ql_mb_get_fw_state(qdev);
	if (status)
		goto exit;
	/* Wake up a worker to get/set the TX/RX frame sizes. */
	queue_delayed_work(qdev->workqueue, &qdev->mpi_port_cfg_work, 0);
exit:
	return status;
}

/* Take the MAC Core out of reset.
 * Enable statistics counting.
 * Take the transmitter/receiver out of reset.
 * This functionality may be done in the MPI firmware at a
 * later date.
 */
static int ql_8012_port_initialize(struct ql_adapter *qdev)
{
	int status = 0;
	u32 data;

	if (ql_sem_trylock(qdev, qdev->xg_sem_mask)) {
		/* Another function has the semaphore, so
		 * wait for the port init bit to come ready.
		 */
		QPRINTK(qdev, LINK, INFO,
			"Another function has the semaphore, so wait for the port init bit to come ready.\n");
		status = ql_wait_reg_rdy(qdev, STS, qdev->port_init, 0);
		if (status) {
			QPRINTK(qdev, LINK, CRIT,
				"Port initialize timed out.\n");
		}
		return status;
	}

	QPRINTK(qdev, LINK, INFO, "Got xgmac semaphore!.\n");
	/* Set the core reset. */
	status = ql_read_xgmac_reg(qdev, GLOBAL_CFG, &data);
	if (status)
		goto end;
	data |= GLOBAL_CFG_RESET;
	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
	if (status)
		goto end;

	/* Clear the core reset and turn on jumbo for receiver. */
	data &= ~GLOBAL_CFG_RESET;	/* Clear core reset. */
	data |= GLOBAL_CFG_JUMBO;	/* Turn on jumbo. */
	data |= GLOBAL_CFG_TX_STAT_EN;
	data |= GLOBAL_CFG_RX_STAT_EN;
	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
	if (status)
		goto end;

	/* Enable transmitter, and clear it's reset. */
	status = ql_read_xgmac_reg(qdev, TX_CFG, &data);
	if (status)
		goto end;
	data &= ~TX_CFG_RESET;	/* Clear the TX MAC reset. */
	data |= TX_CFG_EN;	/* Enable the transmitter. */
	status = ql_write_xgmac_reg(qdev, TX_CFG, data);
	if (status)
		goto end;

	/* Enable receiver and clear it's reset. */
	status = ql_read_xgmac_reg(qdev, RX_CFG, &data);
	if (status)
		goto end;
	data &= ~RX_CFG_RESET;	/* Clear the RX MAC reset. */
	data |= RX_CFG_EN;	/* Enable the receiver. */
	status = ql_write_xgmac_reg(qdev, RX_CFG, data);
	if (status)
		goto end;

	/* Turn on jumbo. */
	status =
	    ql_write_xgmac_reg(qdev, MAC_TX_PARAMS, MAC_TX_PARAMS_JUMBO | (0x2580 << 16));
	if (status)
		goto end;
	status =
	    ql_write_xgmac_reg(qdev, MAC_RX_PARAMS, 0x2580);
	if (status)
		goto end;

	/* Signal to the world that the port is enabled.        */
	ql_write32(qdev, STS, ((qdev->port_init << 16) | qdev->port_init));
end:
	ql_sem_unlock(qdev, qdev->xg_sem_mask);
	return status;
}

/* Get the next large buffer. */
static struct bq_desc *ql_get_curr_lbuf(struct rx_ring *rx_ring)
{
	struct bq_desc *lbq_desc = &rx_ring->lbq[rx_ring->lbq_curr_idx];
	rx_ring->lbq_curr_idx++;
	if (rx_ring->lbq_curr_idx == rx_ring->lbq_len)
		rx_ring->lbq_curr_idx = 0;
	rx_ring->lbq_free_cnt++;
	return lbq_desc;
}

/* Get the next small buffer. */
static struct bq_desc *ql_get_curr_sbuf(struct rx_ring *rx_ring)
{
	struct bq_desc *sbq_desc = &rx_ring->sbq[rx_ring->sbq_curr_idx];
	rx_ring->sbq_curr_idx++;
	if (rx_ring->sbq_curr_idx == rx_ring->sbq_len)
		rx_ring->sbq_curr_idx = 0;
	rx_ring->sbq_free_cnt++;
	return sbq_desc;
}

/* Update an rx ring index. */
static void ql_update_cq(struct rx_ring *rx_ring)
{
	rx_ring->cnsmr_idx++;
	rx_ring->curr_entry++;
	if (unlikely(rx_ring->cnsmr_idx == rx_ring->cq_len)) {
		rx_ring->cnsmr_idx = 0;
		rx_ring->curr_entry = rx_ring->cq_base;
	}
}

static void ql_write_cq_idx(struct rx_ring *rx_ring)
{
	ql_write_db_reg(rx_ring->cnsmr_idx, rx_ring->cnsmr_idx_db_reg);
}

/* Process (refill) a large buffer queue. */
static void ql_update_lbq(struct ql_adapter *qdev, struct rx_ring *rx_ring)
{
	u32 clean_idx = rx_ring->lbq_clean_idx;
	u32 start_idx = clean_idx;
	struct bq_desc *lbq_desc;
	u64 map;
	int i;

	while (rx_ring->lbq_free_cnt > 16) {
		for (i = 0; i < 16; i++) {
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"lbq: try cleaning clean_idx = %d.\n",
				clean_idx);
			lbq_desc = &rx_ring->lbq[clean_idx];
			if (lbq_desc->p.lbq_page == NULL) {
				QPRINTK(qdev, RX_STATUS, DEBUG,
					"lbq: getting new page for index %d.\n",
					lbq_desc->index);
				lbq_desc->p.lbq_page = alloc_page(GFP_ATOMIC);
				if (lbq_desc->p.lbq_page == NULL) {
					rx_ring->lbq_clean_idx = clean_idx;
					QPRINTK(qdev, RX_STATUS, ERR,
						"Couldn't get a page.\n");
					return;
				}
				map = pci_map_page(qdev->pdev,
						   lbq_desc->p.lbq_page,
						   0, PAGE_SIZE,
						   PCI_DMA_FROMDEVICE);
				if (pci_dma_mapping_error(qdev->pdev, map)) {
					rx_ring->lbq_clean_idx = clean_idx;
					put_page(lbq_desc->p.lbq_page);
					lbq_desc->p.lbq_page = NULL;
					QPRINTK(qdev, RX_STATUS, ERR,
						"PCI mapping failed.\n");
					return;
				}
				pci_unmap_addr_set(lbq_desc, mapaddr, map);
				pci_unmap_len_set(lbq_desc, maplen, PAGE_SIZE);
				*lbq_desc->addr = cpu_to_le64(map);
			}
			clean_idx++;
			if (clean_idx == rx_ring->lbq_len)
				clean_idx = 0;
		}

		rx_ring->lbq_clean_idx = clean_idx;
		rx_ring->lbq_prod_idx += 16;
		if (rx_ring->lbq_prod_idx == rx_ring->lbq_len)
			rx_ring->lbq_prod_idx = 0;
		rx_ring->lbq_free_cnt -= 16;
	}

	if (start_idx != clean_idx) {
		QPRINTK(qdev, RX_STATUS, DEBUG,
			"lbq: updating prod idx = %d.\n",
			rx_ring->lbq_prod_idx);
		ql_write_db_reg(rx_ring->lbq_prod_idx,
				rx_ring->lbq_prod_idx_db_reg);
	}
}

/* Process (refill) a small buffer queue. */
static void ql_update_sbq(struct ql_adapter *qdev, struct rx_ring *rx_ring)
{
	u32 clean_idx = rx_ring->sbq_clean_idx;
	u32 start_idx = clean_idx;
	struct bq_desc *sbq_desc;
	u64 map;
	int i;

	while (rx_ring->sbq_free_cnt > 16) {
		for (i = 0; i < 16; i++) {
			sbq_desc = &rx_ring->sbq[clean_idx];
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"sbq: try cleaning clean_idx = %d.\n",
				clean_idx);
			if (sbq_desc->p.skb == NULL) {
				QPRINTK(qdev, RX_STATUS, DEBUG,
					"sbq: getting new skb for index %d.\n",
					sbq_desc->index);
				sbq_desc->p.skb =
				    netdev_alloc_skb(qdev->ndev,
						     rx_ring->sbq_buf_size);
				if (sbq_desc->p.skb == NULL) {
					QPRINTK(qdev, PROBE, ERR,
						"Couldn't get an skb.\n");
					rx_ring->sbq_clean_idx = clean_idx;
					return;
				}
				skb_reserve(sbq_desc->p.skb, QLGE_SB_PAD);
				map = pci_map_single(qdev->pdev,
						     sbq_desc->p.skb->data,
						     rx_ring->sbq_buf_size /
						     2, PCI_DMA_FROMDEVICE);
				if (pci_dma_mapping_error(qdev->pdev, map)) {
					QPRINTK(qdev, IFUP, ERR, "PCI mapping failed.\n");
					rx_ring->sbq_clean_idx = clean_idx;
					dev_kfree_skb_any(sbq_desc->p.skb);
					sbq_desc->p.skb = NULL;
					return;
				}
				pci_unmap_addr_set(sbq_desc, mapaddr, map);
				pci_unmap_len_set(sbq_desc, maplen,
						  rx_ring->sbq_buf_size / 2);
				*sbq_desc->addr = cpu_to_le64(map);
			}

			clean_idx++;
			if (clean_idx == rx_ring->sbq_len)
				clean_idx = 0;
		}
		rx_ring->sbq_clean_idx = clean_idx;
		rx_ring->sbq_prod_idx += 16;
		if (rx_ring->sbq_prod_idx == rx_ring->sbq_len)
			rx_ring->sbq_prod_idx = 0;
		rx_ring->sbq_free_cnt -= 16;
	}

	if (start_idx != clean_idx) {
		QPRINTK(qdev, RX_STATUS, DEBUG,
			"sbq: updating prod idx = %d.\n",
			rx_ring->sbq_prod_idx);
		ql_write_db_reg(rx_ring->sbq_prod_idx,
				rx_ring->sbq_prod_idx_db_reg);
	}
}

static void ql_update_buffer_queues(struct ql_adapter *qdev,
				    struct rx_ring *rx_ring)
{
	ql_update_sbq(qdev, rx_ring);
	ql_update_lbq(qdev, rx_ring);
}

/* Unmaps tx buffers.  Can be called from send() if a pci mapping
 * fails at some stage, or from the interrupt when a tx completes.
 */
static void ql_unmap_send(struct ql_adapter *qdev,
			  struct tx_ring_desc *tx_ring_desc, int mapped)
{
	int i;
	for (i = 0; i < mapped; i++) {
		if (i == 0 || (i == 7 && mapped > 7)) {
			/*
			 * Unmap the skb->data area, or the
			 * external sglist (AKA the Outbound
			 * Address List (OAL)).
			 * If its the zeroeth element, then it's
			 * the skb->data area.  If it's the 7th
			 * element and there is more than 6 frags,
			 * then its an OAL.
			 */
			if (i == 7) {
				QPRINTK(qdev, TX_DONE, DEBUG,
					"unmapping OAL area.\n");
			}
			pci_unmap_single(qdev->pdev,
					 pci_unmap_addr(&tx_ring_desc->map[i],
							mapaddr),
					 pci_unmap_len(&tx_ring_desc->map[i],
						       maplen),
					 PCI_DMA_TODEVICE);
		} else {
			QPRINTK(qdev, TX_DONE, DEBUG, "unmapping frag %d.\n",
				i);
			pci_unmap_page(qdev->pdev,
				       pci_unmap_addr(&tx_ring_desc->map[i],
						      mapaddr),
				       pci_unmap_len(&tx_ring_desc->map[i],
						     maplen), PCI_DMA_TODEVICE);
		}
	}

}

/* Map the buffers for this transmit.  This will return
 * NETDEV_TX_BUSY or NETDEV_TX_OK based on success.
 */
static int ql_map_send(struct ql_adapter *qdev,
		       struct ob_mac_iocb_req *mac_iocb_ptr,
		       struct sk_buff *skb, struct tx_ring_desc *tx_ring_desc)
{
	int len = skb_headlen(skb);
	dma_addr_t map;
	int frag_idx, err, map_idx = 0;
	struct tx_buf_desc *tbd = mac_iocb_ptr->tbd;
	int frag_cnt = skb_shinfo(skb)->nr_frags;

	if (frag_cnt) {
		QPRINTK(qdev, TX_QUEUED, DEBUG, "frag_cnt = %d.\n", frag_cnt);
	}
	/*
	 * Map the skb buffer first.
	 */
	map = pci_map_single(qdev->pdev, skb->data, len, PCI_DMA_TODEVICE);

	err = pci_dma_mapping_error(qdev->pdev, map);
	if (err) {
		QPRINTK(qdev, TX_QUEUED, ERR,
			"PCI mapping failed with error: %d\n", err);

		return NETDEV_TX_BUSY;
	}

	tbd->len = cpu_to_le32(len);
	tbd->addr = cpu_to_le64(map);
	pci_unmap_addr_set(&tx_ring_desc->map[map_idx], mapaddr, map);
	pci_unmap_len_set(&tx_ring_desc->map[map_idx], maplen, len);
	map_idx++;

	/*
	 * This loop fills the remainder of the 8 address descriptors
	 * in the IOCB.  If there are more than 7 fragments, then the
	 * eighth address desc will point to an external list (OAL).
	 * When this happens, the remainder of the frags will be stored
	 * in this list.
	 */
	for (frag_idx = 0; frag_idx < frag_cnt; frag_idx++, map_idx++) {
		skb_frag_t *frag = &skb_shinfo(skb)->frags[frag_idx];
		tbd++;
		if (frag_idx == 6 && frag_cnt > 7) {
			/* Let's tack on an sglist.
			 * Our control block will now
			 * look like this:
			 * iocb->seg[0] = skb->data
			 * iocb->seg[1] = frag[0]
			 * iocb->seg[2] = frag[1]
			 * iocb->seg[3] = frag[2]
			 * iocb->seg[4] = frag[3]
			 * iocb->seg[5] = frag[4]
			 * iocb->seg[6] = frag[5]
			 * iocb->seg[7] = ptr to OAL (external sglist)
			 * oal->seg[0] = frag[6]
			 * oal->seg[1] = frag[7]
			 * oal->seg[2] = frag[8]
			 * oal->seg[3] = frag[9]
			 * oal->seg[4] = frag[10]
			 *      etc...
			 */
			/* Tack on the OAL in the eighth segment of IOCB. */
			map = pci_map_single(qdev->pdev, &tx_ring_desc->oal,
					     sizeof(struct oal),
					     PCI_DMA_TODEVICE);
			err = pci_dma_mapping_error(qdev->pdev, map);
			if (err) {
				QPRINTK(qdev, TX_QUEUED, ERR,
					"PCI mapping outbound address list with error: %d\n",
					err);
				goto map_error;
			}

			tbd->addr = cpu_to_le64(map);
			/*
			 * The length is the number of fragments
			 * that remain to be mapped times the length
			 * of our sglist (OAL).
			 */
			tbd->len =
			    cpu_to_le32((sizeof(struct tx_buf_desc) *
					 (frag_cnt - frag_idx)) | TX_DESC_C);
			pci_unmap_addr_set(&tx_ring_desc->map[map_idx], mapaddr,
					   map);
			pci_unmap_len_set(&tx_ring_desc->map[map_idx], maplen,
					  sizeof(struct oal));
			tbd = (struct tx_buf_desc *)&tx_ring_desc->oal;
			map_idx++;
		}

		map =
		    pci_map_page(qdev->pdev, frag->page,
				 frag->page_offset, frag->size,
				 PCI_DMA_TODEVICE);

		err = pci_dma_mapping_error(qdev->pdev, map);
		if (err) {
			QPRINTK(qdev, TX_QUEUED, ERR,
				"PCI mapping frags failed with error: %d.\n",
				err);
			goto map_error;
		}

		tbd->addr = cpu_to_le64(map);
		tbd->len = cpu_to_le32(frag->size);
		pci_unmap_addr_set(&tx_ring_desc->map[map_idx], mapaddr, map);
		pci_unmap_len_set(&tx_ring_desc->map[map_idx], maplen,
				  frag->size);

	}
	/* Save the number of segments we've mapped. */
	tx_ring_desc->map_cnt = map_idx;
	/* Terminate the last segment. */
	tbd->len = cpu_to_le32(le32_to_cpu(tbd->len) | TX_DESC_E);
	return NETDEV_TX_OK;

map_error:
	/*
	 * If the first frag mapping failed, then i will be zero.
	 * This causes the unmap of the skb->data area.  Otherwise
	 * we pass in the number of frags that mapped successfully
	 * so they can be umapped.
	 */
	ql_unmap_send(qdev, tx_ring_desc, map_idx);
	return NETDEV_TX_BUSY;
}

static void ql_realign_skb(struct sk_buff *skb, int len)
{
	void *temp_addr = skb->data;

	/* Undo the skb_reserve(skb,32) we did before
	 * giving to hardware, and realign data on
	 * a 2-byte boundary.
	 */
	skb->data -= QLGE_SB_PAD - NET_IP_ALIGN;
	skb->tail -= QLGE_SB_PAD - NET_IP_ALIGN;
	skb_copy_to_linear_data(skb, temp_addr,
		(unsigned int)len);
}

/*
 * This function builds an skb for the given inbound
 * completion.  It will be rewritten for readability in the near
 * future, but for not it works well.
 */
static struct sk_buff *ql_build_rx_skb(struct ql_adapter *qdev,
				       struct rx_ring *rx_ring,
				       struct ib_mac_iocb_rsp *ib_mac_rsp)
{
	struct bq_desc *lbq_desc;
	struct bq_desc *sbq_desc;
	struct sk_buff *skb = NULL;
	u32 length = le32_to_cpu(ib_mac_rsp->data_len);
       u32 hdr_len = le32_to_cpu(ib_mac_rsp->hdr_len);

	/*
	 * Handle the header buffer if present.
	 */
	if (ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HV &&
	    ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HS) {
		QPRINTK(qdev, RX_STATUS, DEBUG, "Header of %d bytes in small buffer.\n", hdr_len);
		/*
		 * Headers fit nicely into a small buffer.
		 */
		sbq_desc = ql_get_curr_sbuf(rx_ring);
		pci_unmap_single(qdev->pdev,
				pci_unmap_addr(sbq_desc, mapaddr),
				pci_unmap_len(sbq_desc, maplen),
				PCI_DMA_FROMDEVICE);
		skb = sbq_desc->p.skb;
		ql_realign_skb(skb, hdr_len);
		skb_put(skb, hdr_len);
		sbq_desc->p.skb = NULL;
	}

	/*
	 * Handle the data buffer(s).
	 */
	if (unlikely(!length)) {	/* Is there data too? */
		QPRINTK(qdev, RX_STATUS, DEBUG,
			"No Data buffer in this packet.\n");
		return skb;
	}

	if (ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_DS) {
		if (ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HS) {
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"Headers in small, data of %d bytes in small, combine them.\n", length);
			/*
			 * Data is less than small buffer size so it's
			 * stuffed in a small buffer.
			 * For this case we append the data
			 * from the "data" small buffer to the "header" small
			 * buffer.
			 */
			sbq_desc = ql_get_curr_sbuf(rx_ring);
			pci_dma_sync_single_for_cpu(qdev->pdev,
						    pci_unmap_addr
						    (sbq_desc, mapaddr),
						    pci_unmap_len
						    (sbq_desc, maplen),
						    PCI_DMA_FROMDEVICE);
			memcpy(skb_put(skb, length),
			       sbq_desc->p.skb->data, length);
			pci_dma_sync_single_for_device(qdev->pdev,
						       pci_unmap_addr
						       (sbq_desc,
							mapaddr),
						       pci_unmap_len
						       (sbq_desc,
							maplen),
						       PCI_DMA_FROMDEVICE);
		} else {
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"%d bytes in a single small buffer.\n", length);
			sbq_desc = ql_get_curr_sbuf(rx_ring);
			skb = sbq_desc->p.skb;
			ql_realign_skb(skb, length);
			skb_put(skb, length);
			pci_unmap_single(qdev->pdev,
					 pci_unmap_addr(sbq_desc,
							mapaddr),
					 pci_unmap_len(sbq_desc,
						       maplen),
					 PCI_DMA_FROMDEVICE);
			sbq_desc->p.skb = NULL;
		}
	} else if (ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_DL) {
		if (ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HS) {
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"Header in small, %d bytes in large. Chain large to small!\n", length);
			/*
			 * The data is in a single large buffer.  We
			 * chain it to the header buffer's skb and let
			 * it rip.
			 */
			lbq_desc = ql_get_curr_lbuf(rx_ring);
			pci_unmap_page(qdev->pdev,
				       pci_unmap_addr(lbq_desc,
						      mapaddr),
				       pci_unmap_len(lbq_desc, maplen),
				       PCI_DMA_FROMDEVICE);
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"Chaining page to skb.\n");
			skb_fill_page_desc(skb, 0, lbq_desc->p.lbq_page,
					   0, length);
			skb->len += length;
			skb->data_len += length;
			skb->truesize += length;
			lbq_desc->p.lbq_page = NULL;
		} else {
			/*
			 * The headers and data are in a single large buffer. We
			 * copy it to a new skb and let it go. This can happen with
			 * jumbo mtu on a non-TCP/UDP frame.
			 */
			lbq_desc = ql_get_curr_lbuf(rx_ring);
			skb = netdev_alloc_skb(qdev->ndev, length);
			if (skb == NULL) {
				QPRINTK(qdev, PROBE, DEBUG,
					"No skb available, drop the packet.\n");
				return NULL;
			}
			pci_unmap_page(qdev->pdev,
				       pci_unmap_addr(lbq_desc,
						      mapaddr),
				       pci_unmap_len(lbq_desc, maplen),
				       PCI_DMA_FROMDEVICE);
			skb_reserve(skb, NET_IP_ALIGN);
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"%d bytes of headers and data in large. Chain page to new skb and pull tail.\n", length);
			skb_fill_page_desc(skb, 0, lbq_desc->p.lbq_page,
					   0, length);
			skb->len += length;
			skb->data_len += length;
			skb->truesize += length;
			length -= length;
			lbq_desc->p.lbq_page = NULL;
			__pskb_pull_tail(skb,
				(ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V) ?
				VLAN_ETH_HLEN : ETH_HLEN);
		}
	} else {
		/*
		 * The data is in a chain of large buffers
		 * pointed to by a small buffer.  We loop
		 * thru and chain them to the our small header
		 * buffer's skb.
		 * frags:  There are 18 max frags and our small
		 *         buffer will hold 32 of them. The thing is,
		 *         we'll use 3 max for our 9000 byte jumbo
		 *         frames.  If the MTU goes up we could
		 *          eventually be in trouble.
		 */
		int size, offset, i = 0;
		__le64 *bq, bq_array[8];
		sbq_desc = ql_get_curr_sbuf(rx_ring);
		pci_unmap_single(qdev->pdev,
				 pci_unmap_addr(sbq_desc, mapaddr),
				 pci_unmap_len(sbq_desc, maplen),
				 PCI_DMA_FROMDEVICE);
		if (!(ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HS)) {
			/*
			 * This is an non TCP/UDP IP frame, so
			 * the headers aren't split into a small
			 * buffer.  We have to use the small buffer
			 * that contains our sg list as our skb to
			 * send upstairs. Copy the sg list here to
			 * a local buffer and use it to find the
			 * pages to chain.
			 */
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"%d bytes of headers & data in chain of large.\n", length);
			skb = sbq_desc->p.skb;
			bq = &bq_array[0];
			memcpy(bq, skb->data, sizeof(bq_array));
			sbq_desc->p.skb = NULL;
			skb_reserve(skb, NET_IP_ALIGN);
		} else {
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"Headers in small, %d bytes of data in chain of large.\n", length);
			bq = (__le64 *)sbq_desc->p.skb->data;
		}
		while (length > 0) {
			lbq_desc = ql_get_curr_lbuf(rx_ring);
			pci_unmap_page(qdev->pdev,
				       pci_unmap_addr(lbq_desc,
						      mapaddr),
				       pci_unmap_len(lbq_desc,
						     maplen),
				       PCI_DMA_FROMDEVICE);
			size = (length < PAGE_SIZE) ? length : PAGE_SIZE;
			offset = 0;

			QPRINTK(qdev, RX_STATUS, DEBUG,
				"Adding page %d to skb for %d bytes.\n",
				i, size);
			skb_fill_page_desc(skb, i, lbq_desc->p.lbq_page,
					   offset, size);
			skb->len += size;
			skb->data_len += size;
			skb->truesize += size;
			length -= size;
			lbq_desc->p.lbq_page = NULL;
			bq++;
			i++;
		}
		__pskb_pull_tail(skb, (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V) ?
				VLAN_ETH_HLEN : ETH_HLEN);
	}
	return skb;
}

/* Process an inbound completion from an rx ring. */
static void ql_process_mac_rx_intr(struct ql_adapter *qdev,
				   struct rx_ring *rx_ring,
				   struct ib_mac_iocb_rsp *ib_mac_rsp)
{
	struct net_device *ndev = qdev->ndev;
	struct sk_buff *skb = NULL;
	u16 vlan_id = (le16_to_cpu(ib_mac_rsp->vlan_id) &
			IB_MAC_IOCB_RSP_VLAN_MASK)

	QL_DUMP_IB_MAC_RSP(ib_mac_rsp);

	skb = ql_build_rx_skb(qdev, rx_ring, ib_mac_rsp);
	if (unlikely(!skb)) {
		QPRINTK(qdev, RX_STATUS, DEBUG,
			"No skb available, drop packet.\n");
		return;
	}

	/* Frame error, so drop the packet. */
	if (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_ERR_MASK) {
		QPRINTK(qdev, DRV, ERR, "Receive error, flags2 = 0x%x\n",
					ib_mac_rsp->flags2);
		dev_kfree_skb_any(skb);
		return;
	}

	/* The max framesize filter on this chip is set higher than
	 * MTU since FCoE uses 2k frames.
	 */
	if (skb->len > ndev->mtu + ETH_HLEN) {
		dev_kfree_skb_any(skb);
		return;
	}

	prefetch(skb->data);
	skb->dev = ndev;
	if (ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) {
		QPRINTK(qdev, RX_STATUS, DEBUG, "%s%s%s Multicast.\n",
			(ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) ==
			IB_MAC_IOCB_RSP_M_HASH ? "Hash" : "",
			(ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) ==
			IB_MAC_IOCB_RSP_M_REG ? "Registered" : "",
			(ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) ==
			IB_MAC_IOCB_RSP_M_PROM ? "Promiscuous" : "");
	}
	if (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_P) {
		QPRINTK(qdev, RX_STATUS, DEBUG, "Promiscuous Packet.\n");
	}

	skb->protocol = eth_type_trans(skb, ndev);
	skb->ip_summed = CHECKSUM_NONE;

	/* If rx checksum is on, and there are no
	 * csum or frame errors.
	 */
	if (qdev->rx_csum &&
		!(ib_mac_rsp->flags1 & IB_MAC_CSUM_ERR_MASK)) {
		/* TCP frame. */
		if (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_T) {
			QPRINTK(qdev, RX_STATUS, DEBUG,
					"TCP checksum done!\n");
			skb->ip_summed = CHECKSUM_UNNECESSARY;
		} else if ((ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_U) &&
				(ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_V4)) {
		/* Unfragmented ipv4 UDP frame. */
			struct iphdr *iph = (struct iphdr *) skb->data;
			if (!(iph->frag_off &
				cpu_to_be16(IP_MF|IP_OFFSET))) {
				skb->ip_summed = CHECKSUM_UNNECESSARY;
				QPRINTK(qdev, RX_STATUS, DEBUG,
						"TCP checksum done!\n");
			}
		}
	}

	qdev->stats.rx_packets++;
	qdev->stats.rx_bytes += skb->len;
	skb_record_rx_queue(skb, rx_ring->cq_id);
	if (skb->ip_summed == CHECKSUM_UNNECESSARY) {
		if (qdev->vlgrp &&
			(ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V) &&
			(vlan_id != 0))
			vlan_gro_receive(&rx_ring->napi, qdev->vlgrp,
				vlan_id, skb);
		else
			napi_gro_receive(&rx_ring->napi, skb);
	} else {
		if (qdev->vlgrp &&
			(ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V) &&
			(vlan_id != 0))
			vlan_hwaccel_receive_skb(skb, qdev->vlgrp, vlan_id);
		else
			netif_receive_skb(skb);
	}
}

/* Process an outbound completion from an rx ring. */
static void ql_process_mac_tx_intr(struct ql_adapter *qdev,
				   struct ob_mac_iocb_rsp *mac_rsp)
{
	struct tx_ring *tx_ring;
	struct tx_ring_desc *tx_ring_desc;

	QL_DUMP_OB_MAC_RSP(mac_rsp);
	tx_ring = &qdev->tx_ring[mac_rsp->txq_idx];
	tx_ring_desc = &tx_ring->q[mac_rsp->tid];
	ql_unmap_send(qdev, tx_ring_desc, tx_ring_desc->map_cnt);
	qdev->stats.tx_bytes += (tx_ring_desc->skb)->len;
	qdev->stats.tx_packets++;
	dev_kfree_skb(tx_ring_desc->skb);
	tx_ring_desc->skb = NULL;

	if (unlikely(mac_rsp->flags1 & (OB_MAC_IOCB_RSP_E |
					OB_MAC_IOCB_RSP_S |
					OB_MAC_IOCB_RSP_L |
					OB_MAC_IOCB_RSP_P | OB_MAC_IOCB_RSP_B))) {
		if (mac_rsp->flags1 & OB_MAC_IOCB_RSP_E) {
			QPRINTK(qdev, TX_DONE, WARNING,
				"Total descriptor length did not match transfer length.\n");
		}
		if (mac_rsp->flags1 & OB_MAC_IOCB_RSP_S) {
			QPRINTK(qdev, TX_DONE, WARNING,
				"Frame too short to be legal, not sent.\n");
		}
		if (mac_rsp->flags1 & OB_MAC_IOCB_RSP_L) {
			QPRINTK(qdev, TX_DONE, WARNING,
				"Frame too long, but sent anyway.\n");
		}
		if (mac_rsp->flags1 & OB_MAC_IOCB_RSP_B) {
			QPRINTK(qdev, TX_DONE, WARNING,
				"PCI backplane error. Frame not sent.\n");
		}
	}
	atomic_inc(&tx_ring->tx_count);
}

/* Fire up a handler to reset the MPI processor. */
void ql_queue_fw_error(struct ql_adapter *qdev)
{
	ql_link_off(qdev);
	queue_delayed_work(qdev->workqueue, &qdev->mpi_reset_work, 0);
}

void ql_queue_asic_error(struct ql_adapter *qdev)
{
	ql_link_off(qdev);
	ql_disable_interrupts(qdev);
	/* Clear adapter up bit to signal the recovery
	 * process that it shouldn't kill the reset worker
	 * thread
	 */
	clear_bit(QL_ADAPTER_UP, &qdev->flags);
	queue_delayed_work(qdev->workqueue, &qdev->asic_reset_work, 0);
}

static void ql_process_chip_ae_intr(struct ql_adapter *qdev,
				    struct ib_ae_iocb_rsp *ib_ae_rsp)
{
	switch (ib_ae_rsp->event) {
	case MGMT_ERR_EVENT:
		QPRINTK(qdev, RX_ERR, ERR,
			"Management Processor Fatal Error.\n");
		ql_queue_fw_error(qdev);
		return;

	case CAM_LOOKUP_ERR_EVENT:
		QPRINTK(qdev, LINK, ERR,
			"Multiple CAM hits lookup occurred.\n");
		QPRINTK(qdev, DRV, ERR, "This event shouldn't occur.\n");
		ql_queue_asic_error(qdev);
		return;

	case SOFT_ECC_ERROR_EVENT:
		QPRINTK(qdev, RX_ERR, ERR, "Soft ECC error detected.\n");
		ql_queue_asic_error(qdev);
		break;

	case PCI_ERR_ANON_BUF_RD:
		QPRINTK(qdev, RX_ERR, ERR,
			"PCI error occurred when reading anonymous buffers from rx_ring %d.\n",
			ib_ae_rsp->q_id);
		ql_queue_asic_error(qdev);
		break;

	default:
		QPRINTK(qdev, DRV, ERR, "Unexpected event %d.\n",
			ib_ae_rsp->event);
		ql_queue_asic_error(qdev);
		break;
	}
}

static int ql_clean_outbound_rx_ring(struct rx_ring *rx_ring)
{
	struct ql_adapter *qdev = rx_ring->qdev;
	u32 prod = ql_read_sh_reg(rx_ring->prod_idx_sh_reg);
	struct ob_mac_iocb_rsp *net_rsp = NULL;
	int count = 0;

	struct tx_ring *tx_ring;
	/* While there are entries in the completion queue. */
	while (prod != rx_ring->cnsmr_idx) {

		QPRINTK(qdev, RX_STATUS, DEBUG,
			"cq_id = %d, prod = %d, cnsmr = %d.\n.", rx_ring->cq_id,
			prod, rx_ring->cnsmr_idx);

		net_rsp = (struct ob_mac_iocb_rsp *)rx_ring->curr_entry;
		rmb();
		switch (net_rsp->opcode) {

		case OPCODE_OB_MAC_TSO_IOCB:
		case OPCODE_OB_MAC_IOCB:
			ql_process_mac_tx_intr(qdev, net_rsp);
			break;
		default:
			QPRINTK(qdev, RX_STATUS, DEBUG,
				"Hit default case, not handled! dropping the packet, opcode = %x.\n",
				net_rsp->opcode);
		}
		count++;
		ql_update_cq(rx_ring);
		prod = ql_read_sh_reg(rx_ring->prod_idx_sh_reg);
	}
	ql_write_cq_idx(rx_ring);
	tx_ring = &qdev->tx_ring[net_rsp->txq_idx];
	if (__netif_subqueue_stopped(qdev->ndev, tx_ring->wq_id) &&
					net_rsp != NULL) {
		if (atomic_read(&tx_ring->queue_stopped) &&
		    (atomic_read(&tx_ring->tx_count) > (tx_ring->wq_len / 4)))
			/*
			 * The queue got stopped because the tx_ring was full.
			 * Wake it up, because it's now at least 25% empty.
			 */
			netif_wake_subqueue(qdev->ndev, tx_ring->wq_id);
	}

	return count;
}

static int ql_clean_inbound_rx_ring(struct rx_ring *rx_ring, int budget)
{
	struct ql_adapter *qdev = rx_ring->qdev;
	u32 prod = ql_read_sh_reg(rx_ring->prod_idx_sh_reg);
	struct ql_net_rsp_iocb *net_rsp;
	int count = 0;

	/* While there are entries in the completion queue. */
	while (prod != rx_ring->cnsmr_idx) {

		QPRINTK(qdev, RX_STATUS, DEBUG,
			"cq_id = %d, prod = %d, cnsmr = %d.\n.", rx_ring->cq_id,
			prod, rx_ring->cnsmr_idx);

		net_rsp = rx_ring->curr_entry;
		rmb();
		switch (net_rsp->opcode) {
		case OPCODE_IB_MAC_IOCB:
			ql_process_mac_rx_intr(qdev, rx_ring,
					       (struct ib_mac_iocb_rsp *)
					       net_rsp);
			break;

		case OPCODE_IB_AE_IOCB:
			ql_process_chip_ae_intr(qdev, (struct ib_ae_iocb_rsp *)
						net_rsp);
			break;
		default:
			{
				QPRINTK(qdev, RX_STATUS, DEBUG,
					"Hit default case, not handled! dropping the packet, opcode = %x.\n",
					net_rsp->opcode);
			}
		}
		count++;
		ql_update_cq(rx_ring);
		prod = ql_read_sh_reg(rx_ring->prod_idx_sh_reg);
		if (count == budget)
			break;
	}
	ql_update_buffer_queues(qdev, rx_ring);
	ql_write_cq_idx(rx_ring);
	return count;
}

static int ql_napi_poll_msix(struct napi_struct *napi, int budget)
{
	struct rx_ring *rx_ring = container_of(napi, struct rx_ring, napi);
	struct ql_adapter *qdev = rx_ring->qdev;
	struct rx_ring *trx_ring;
	int i, work_done = 0;
	struct intr_context *ctx = &qdev->intr_context[rx_ring->cq_id];

	QPRINTK(qdev, RX_STATUS, DEBUG, "Enter, NAPI POLL cq_id = %d.\n",
		rx_ring->cq_id);

	/* Service the TX rings first.  They start
	 * right after the RSS rings. */
	for (i = qdev->rss_ring_count; i < qdev->rx_ring_count; i++) {
		trx_ring = &qdev->rx_ring[i];
		/* If this TX completion ring belongs to this vector and
		 * it's not empty then service it.
		 */
		if ((ctx->irq_mask & (1 << trx_ring->cq_id)) &&
			(ql_read_sh_reg(trx_ring->prod_idx_sh_reg) !=
					trx_ring->cnsmr_idx)) {
			QPRINTK(qdev, INTR, DEBUG,
				"%s: Servicing TX completion ring %d.\n",
				__func__, trx_ring->cq_id);
			ql_clean_outbound_rx_ring(trx_ring);
		}
	}

	/*
	 * Now service the RSS ring if it's active.
	 */
	if (ql_read_sh_reg(rx_ring->prod_idx_sh_reg) !=
					rx_ring->cnsmr_idx) {
		QPRINTK(qdev, INTR, DEBUG,
			"%s: Servicing RX completion ring %d.\n",
			__func__, rx_ring->cq_id);
		work_done = ql_clean_inbound_rx_ring(rx_ring, budget);
	}

	if (work_done < budget) {
		napi_complete(napi);
		ql_enable_completion_interrupt(qdev, rx_ring->irq);
	}
	return work_done;
}

static void ql_vlan_rx_register(struct net_device *ndev, struct vlan_group *grp)
{
	struct ql_adapter *qdev = netdev_priv(ndev);

	qdev->vlgrp = grp;
	if (grp) {
		QPRINTK(qdev, IFUP, DEBUG, "Turning on VLAN in NIC_RCV_CFG.\n");
		ql_write32(qdev, NIC_RCV_CFG, NIC_RCV_CFG_VLAN_MASK |
			   NIC_RCV_CFG_VLAN_MATCH_AND_NON);
	} else {
		QPRINTK(qdev, IFUP, DEBUG,
			"Turning off VLAN in NIC_RCV_CFG.\n");
		ql_write32(qdev, NIC_RCV_CFG, NIC_RCV_CFG_VLAN_MASK);
	}
}

static void ql_vlan_rx_add_vid(struct net_device *ndev, u16 vid)
{
	struct ql_adapter *qdev = netdev_priv(ndev);
	u32 enable_bit = MAC_ADDR_E;
	int status;

	status = ql_sem_spinlock(qdev, SEM_MAC_ADDR_MASK);
	if (status)
		return;
	if (ql_set_mac_addr_reg
	    (qdev, (u8 *) &enable_bit, MAC_ADDR_TYPE_VLAN, vid)) {
		QPRINTK(qdev, IFUP, ERR, "Failed to init vlan address.\n");
	}
	ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK);
}

static void ql_vlan_rx_kill_vid(struct net_device *ndev, u16 vid)
{
	struct ql_adapter *qdev = netdev_priv(ndev);
	u32 enable_bit = 0;
	int status;

	status = ql_sem_spinlock(qdev, SEM_MAC_ADDR_MASK);
	if (status)
		return;

	if (ql_set_mac_addr_reg
	    (qdev, (u8 *) &enable_bit, MAC_ADDR_TYPE_VLAN, vid)) {
		QPRINTK(qdev, IFUP, ERR, "Failed to clear vlan address.\n");
	}
	ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK);

}

/* MSI-X Multiple Vector Interrupt Handler for inbound completions. */
static irqreturn_t qlge_msix_rx_isr(int irq, void *dev_id)
{
	struct rx_ring *rx_ring = dev_id;
	napi_schedule(&rx_ring->napi);
	return IRQ_HANDLED;
}

/* This handles a fatal error, MPI activity, and the default
 * rx_ring in an MSI-X multiple vector environment.
 * In MSI/Legacy environment it also process the rest of
 * the rx_rings.
 */
static irqreturn_t qlge_isr(int irq, void *dev_id)
{
	struct rx_ring *rx_ring = dev_id;
	struct ql_adapter *qdev = rx_ring->qdev;
	struct intr_context *intr_context = &qdev->intr_context[0];
	u32 var;
	int work_done = 0;

	spin_lock(&qdev->hw_lock);
	if (atomic_read(&qdev->intr_context[0].irq_cnt)) {
		QPRINTK(qdev, INTR, DEBUG, "Shared Interrupt, Not ours!\n");
		spin_unlock(&qdev->hw_lock);
		return IRQ_NONE;
	}
	spin_unlock(&qdev->hw_lock);

	var = ql_disable_completion_interrupt(qdev, intr_context->intr);

	/*
	 * Check for fatal error.
	 */
	if (var & STS_FE) {
		ql_queue_asic_error(qdev);
		QPRINTK(qdev, INTR, ERR, "Got fatal error, STS = %x.\n", var);
		var = ql_read32(qdev, ERR_STS);
		QPRINTK(qdev, INTR, ERR,
			"Resetting chip. Error Status Register = 0x%x\n", var);
		return IRQ_HANDLED;
	}

	/*
	 * Check MPI processor activity.
	 */
	if ((var & STS_PI) &&
		(ql_read32(qdev, INTR_MASK) & INTR_MASK_PI)) {
		/*
		 * We've got an async event or mailbox completion.
		 * Handle it and clear the source of the interrupt.
		 */
		QPRINTK(qdev, INTR, ERR, "Got MPI processor interrupt.\n");
		ql_disable_completion_interrupt(qdev, intr_context->intr);
		ql_write32(qdev, INTR_MASK, (INTR_MASK_PI << 16));
		queue_delayed_work_on(smp_processor_id(),
				qdev->workqueue, &qdev->mpi_work, 0);
		work_done++;
	}

	/*
	 * Get the bit-mask that shows the active queues for this
	 * pass.  Compare it to the queues that this irq services
	 * and call napi if there's a match.
	 */
	var = ql_read32(qdev, ISR1);
	if (var & intr_context->irq_mask) {
				QPRINTK(qdev, INTR, INFO,
			"Waking handler for rx_ring[0].\n");
		ql_disable_completion_interrupt(qdev, intr_context->intr);
					napi_schedule(&rx_ring->napi);
				work_done++;
			}
	ql_enable_completion_interrupt(qdev, intr_context->intr);
	return work_done ? IRQ_HANDLED : IRQ_NONE;
}

static int ql_tso(struct sk_buff *skb, struct ob_mac_tso_iocb_req *mac_iocb_ptr)
{

	if (skb_is_gso(skb)) {
		int err;
		if (skb_header_cloned(skb)) {
			err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
			if (err)
				return err;
		}

		mac_iocb_ptr->opcode = OPCODE_OB_MAC_TSO_IOCB;
		mac_iocb_ptr->flags3 |= OB_MAC_TSO_IOCB_IC;
		mac_iocb_ptr->frame_len = cpu_to_le32((u32) skb->len);
		mac_iocb_ptr->total_hdrs_len =
		    cpu_to_le16(skb_transport_offset(skb) + tcp_hdrlen(skb));
		mac_iocb_ptr->net_trans_offset =
		    cpu_to_le16(skb_network_offset(skb) |
				skb_transport_offset(skb)
				<< OB_MAC_TRANSPORT_HDR_SHIFT);
		mac_iocb_ptr->mss = cpu_to_le16(skb_shinfo(skb)->gso_size);
		mac_iocb_ptr->flags2 |= OB_MAC_TSO_IOCB_LSO;
		if (likely(skb->protocol == htons(ETH_P_IP))) {
			struct iphdr *iph = ip_hdr(skb);
			iph->check = 0;
			mac_iocb_ptr->flags1 |= OB_MAC_TSO_IOCB_IP4;
			tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr,
								 iph->daddr, 0,
								 IPPROTO_TCP,
								 0);
		} else if (skb->protocol == htons(ETH_P_IPV6)) {
			mac_iocb_ptr->flags1 |= OB_MAC_TSO_IOCB_IP6;
			tcp_hdr(skb)->check =
			    ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
					     &ipv6_hdr(skb)->daddr,
					     0, IPPROTO_TCP, 0);
		}
		return 1;
	}
	return 0;
}

static void ql_hw_csum_setup(struct sk_buff *skb,
			     struct ob_mac_tso_iocb_req *mac_iocb_ptr)
{
	int len;
	struct iphdr *iph = ip_hdr(skb);
	__sum16 *check;
	mac_iocb_ptr->opcode = OPCODE_OB_MAC_TSO_IOCB;
	mac_iocb_ptr->frame_len = cpu_to_le32((u32) skb->len);
	mac_iocb_ptr->net_trans_offset =
		cpu_to_le16(skb_network_offset(skb) |
		skb_transport_offset(skb) << OB_MAC_TRANSPORT_HDR_SHIFT);

	mac_iocb_ptr->flags1 |= OB_MAC_TSO_IOCB_IP4;
	len = (ntohs(iph->tot_len) - (iph->ihl << 2));
	if (likely(iph->protocol == IPPROTO_TCP)) {
		check = &(tcp_hdr(skb)->check);
		mac_iocb_ptr->flags2 |= OB_MAC_TSO_IOCB_TC;
		mac_iocb_ptr->total_hdrs_len =
		    cpu_to_le16(skb_transport_offset(skb) +
				(tcp_hdr(skb)->doff << 2));
	} else {
		check = &(udp_hdr(skb)->check);
		mac_iocb_ptr->flags2 |= OB_MAC_TSO_IOCB_UC;
		mac_iocb_ptr->total_hdrs_len =
		    cpu_to_le16(skb_transport_offset(skb) +
				sizeof(struct udphdr));
	}
	*check = ~csum_tcpudp_magic(iph->saddr,
				    iph->daddr, len, iph->protocol, 0);
}

static netdev_tx_t qlge_send(struct sk_buff *skb, struct net_device *ndev)
{
	struct tx_ring_desc *tx_ring_desc;
	struct ob_mac_iocb_req *mac_iocb_ptr;
	struct ql_adapter *qdev = netdev_priv(ndev);
	int tso;
	struct tx_ring *tx_ring;
	u32 tx_ring_idx = (u32) skb->queue_mapping;

	tx_ring = &qdev->tx_ring[tx_ring_idx];

	if (skb_padto(skb, ETH_ZLEN))
		return NETDEV_TX_OK;

	if (unlikely(atomic_read(&tx_ring->tx_count) < 2)) {
		QPRINTK(qdev, TX_QUEUED, INFO,
			"%s: shutting down tx queue %d du to lack of resources.\n",
			__func__, tx_ring_idx);
		netif_stop_subqueue(ndev, tx_ring->wq_id);
		atomic_inc(&tx_ring->queue_stopped);
		return NETDEV_TX_BUSY;
	}
	tx_ring_desc = &tx_ring->q[tx_ring->prod_idx];
	mac_iocb_ptr = tx_ring_desc->queue_entry;
	memset((void *)mac_iocb_ptr, 0, sizeof(*mac_iocb_ptr));

	mac_iocb_ptr->opcode = OPCODE_OB_MAC_IOCB;
	mac_iocb_ptr->tid = tx_ring_desc->index;
	/* We use the upper 32-bits to store the tx queue for this IO.
	 * When we get the completion we can use it to establish the context.
	 */
	mac_iocb_ptr->txq_idx = tx_ring_idx;
	tx_ring_desc->skb = skb;

	mac_iocb_ptr->frame_len = cpu_to_le16((u16) skb->len);

	if (qdev->vlgrp && vlan_tx_tag_present(skb)) {
		QPRINTK(qdev, TX_QUEUED, DEBUG, "Adding a vlan tag %d.\n",
			vlan_tx_tag_get(skb));
		mac_iocb_ptr->flags3 |= OB_MAC_IOCB_V;
		mac_iocb_ptr->vlan_tci = cpu_to_le16(vlan_tx_tag_get(skb));
	}
	tso = ql_tso(skb, (struct ob_mac_tso_iocb_req *)mac_iocb_ptr);
	if (tso < 0) {
		dev_kfree_skb_any(skb);
		return NETDEV_TX_OK;
	} else if (unlikely(!tso) && (skb->ip_summed == CHECKSUM_PARTIAL)) {
		ql_hw_csum_setup(skb,
				 (struct ob_mac_tso_iocb_req *)mac_iocb_ptr);
	}
	if (ql_map_send(qdev, mac_iocb_ptr, skb, tx_ring_desc) !=
			NETDEV_TX_OK) {
		QPRINTK(qdev, TX_QUEUED, ERR,
				"Could not map the segments.\n");
		return NETDEV_TX_BUSY;
	}
	QL_DUMP_OB_MAC_IOCB(mac_iocb_ptr);
	tx_ring->prod_idx++;
	if (tx_ring->prod_idx == tx_ring->wq_len)
		tx_ring->prod_idx = 0;
	wmb();

	ql_write_db_reg(tx_ring->prod_idx, tx_ring->prod_idx_db_reg);
	QPRINTK(qdev, TX_QUEUED, DEBUG, "tx queued, slot %d, len %d\n",
		tx_ring->prod_idx, skb->len);

	atomic_dec(&tx_ring->tx_count);
	return NETDEV_TX_OK;
}

static void ql_free_shadow_space(struct ql_adapter *qdev)
{
	if (qdev->rx_ring_shadow_reg_area) {
		pci_free_consistent(qdev->pdev,
				    PAGE_SIZE,
				    qdev->rx_ring_shadow_reg_area,
				    qdev->rx_ring_shadow_reg_dma);
		qdev->rx_ring_shadow_reg_area = NULL;
	}
	if (qdev->tx_ring_shadow_reg_area) {
		pci_free_consistent(qdev->pdev,
				    PAGE_SIZE,
				    qdev->tx_ring_shadow_reg_area,
				    qdev->tx_ring_shadow_reg_dma);
		qdev->tx_ring_shadow_reg_area = NULL;
	}
}

static int ql_alloc_shadow_space(struct ql_adapter *qdev)
{
	qdev->rx_ring_shadow_reg_area =
	    pci_alloc_consistent(qdev->pdev,
				 PAGE_SIZE, &qdev->rx_ring_shadow_reg_dma);
	if (qdev->rx_ring_shadow_reg_area == NULL) {
		QPRINTK(qdev, IFUP, ERR,
			"Allocation of RX shadow space failed.\n");
		return -ENOMEM;
	}
	memset(qdev->rx_ring_shadow_reg_area, 0, PAGE_SIZE);
	qdev->tx_ring_shadow_reg_area =
	    pci_alloc_consistent(qdev->pdev, PAGE_SIZE,
				 &qdev->tx_ring_shadow_reg_dma);
	if (qdev->tx_ring_shadow_reg_area == NULL) {
		QPRINTK(qdev, IFUP, ERR,
			"Allocation of TX shadow space failed.\n");
		goto err_wqp_sh_area;
	}
	memset(qdev->tx_ring_shadow_reg_area, 0, PAGE_SIZE);
	return 0;

err_wqp_sh_area:
	pci_free_consistent(qdev->pdev,
			    PAGE_SIZE,
			    qdev->rx_ring_shadow_reg_area,
			    qdev->rx_ring_shadow_reg_dma);
	return -ENOMEM;
}

static void ql_init_tx_ring(struct ql_adapter *qdev, struct tx_ring *tx_ring)
{
	struct tx_ring_desc *tx_ring_desc;
	int i;
	struct ob_mac_iocb_req *mac_iocb_ptr;

	mac_iocb_ptr = tx_ring->wq_base;
	tx_ring_desc = tx_ring->q;
	for (i = 0; i < tx_ring->wq_len; i++) {
		tx_ring_desc->index = i;
		tx_ring_desc->skb = NULL;
		tx_ring_desc->queue_entry = mac_iocb_ptr;
		mac_iocb_ptr++;
		tx_ring_desc++;
	}
	atomic_set(&tx_ring->tx_count, tx_ring->wq_len);
	atomic_set(&tx_ring->queue_stopped, 0);
}

static void ql_free_tx_resources(struct ql_adapter *qdev,
				 struct tx_ring *tx_ring)
{
	if (tx_ring->wq_base) {
		pci_free_consistent(qdev->pdev, tx_ring->wq_size,
				    tx_ring->wq_base, tx_ring->wq_base_dma);
		tx_ring->wq_base = NULL;
	}
	kfree(tx_ring->q);
	tx_ring->q = NULL;
}

static int ql_alloc_tx_resources(struct ql_adapter *qdev,
				 struct tx_ring *tx_ring)
{
	tx_ring->wq_base =
	    pci_alloc_consistent(qdev->pdev, tx_ring->wq_size,
				 &tx_ring->wq_base_dma);

	if ((tx_ring->wq_base == NULL)
		|| tx_ring->wq_base_dma & WQ_ADDR_ALIGN) {
		QPRINTK(qdev, IFUP, ERR, "tx_ring alloc failed.\n");
		return -ENOMEM;
	}
	tx_ring->q =
	    kmalloc(tx_ring->wq_len * sizeof(struct tx_ring_desc), GFP_KERNEL);
	if (tx_ring->q == NULL)
		goto err;

	return 0;
err:
	pci_free_consistent(qdev->pdev, tx_ring->wq_size,
			    tx_ring->wq_base, tx_ring->wq_base_dma);
	return -ENOMEM;
}

static void ql_free_lbq_buffers(struct ql_adapter *qdev, struct rx_ring *rx_ring)
{
	int i;
	struct bq_desc *lbq_desc;

	for (i = 0; i < rx_ring->lbq_len; i++) {
		lbq_desc = &rx_ring->lbq[i];
		if (lbq_desc->p.lbq_page) {
			pci_unmap_page(qdev->pdev,
				       pci_unmap_addr(lbq_desc, mapaddr),
				       pci_unmap_len(lbq_desc, maplen),
				       PCI_DMA_FROMDEVICE);

			put_page(lbq_desc->p.lbq_page);
			lbq_desc->p.lbq_page = NULL;
		}
	}
}

static void ql_free_sbq_buffers(struct ql_adapter *qdev, struct rx_ring *rx_ring)
{
	int i;
	struct bq_desc *sbq_desc;

	for (i = 0; i < rx_ring->sbq_len; i++) {
		sbq_desc = &rx_ring->sbq[i];
		if (sbq_desc == NULL) {
			QPRINTK(qdev, IFUP, ERR, "sbq_desc %d is NULL.\n", i);
			return;
		}
		if (sbq_desc->p.skb) {
			pci_unmap_single(qdev->pdev,
					 pci_unmap_addr(sbq_desc, mapaddr),
					 pci_unmap_len(sbq_desc, maplen),
					 PCI_DMA_FROMDEVICE);
			dev_kfree_skb(sbq_desc->p.skb);
			sbq_desc->p.skb = NULL;
		}
	}
}

/* Free all large and small rx buffers associated
 * with the completion queues for this device.
 */
static void ql_free_rx_buffers(struct ql_adapter *qdev)
{
	int i;
	struct rx_ring *rx_ring;

	for (i = 0; i < qdev->rx_ring_count; i++) {
		rx_ring = &qdev->rx_ring[i];
		if (rx_ring->lbq)
			ql_free_lbq_buffers(qdev, rx_ring);
		if (rx_ring->sbq)
			ql_free_sbq_buffers(qdev, rx_ring);
	}
}

static void ql_alloc_rx_buffers(struct ql_adapter *qdev)
{
	struct rx_ring *rx_ring;
	int i;

	for (i = 0; i < qdev->rx_ring_count; i++) {
		rx_ring = &qdev->rx_ring[i];
		if (rx_ring->type != TX_Q)
			ql_update_buffer_queues(qdev, rx_ring);
	}
}

static void ql_init_lbq_ring(struct ql_adapter *qdev,
				struct rx_ring *rx_ring)
{
	int i;
	struct bq_desc *lbq_desc;
	__le64 *bq = rx_ring->lbq_base;

	memset(rx_ring->lbq, 0, rx_ring->lbq_len * sizeof(struct bq_desc));
	for (i = 0; i < rx_ring->lbq_len; i++) {
		lbq_desc = &rx_ring->lbq[i];
		memset(lbq_desc, 0, sizeof(*lbq_desc));
		lbq_desc->index = i;
		lbq_desc->addr = bq;
		bq++;
	}
}

static void ql_init_sbq_ring(struct ql_adapter *qdev,
				struct rx_ring *rx_ring)
{
	int i;
	struct bq_desc *sbq_desc;
	__le64 *bq = rx_ring->sbq_base;

	memset(rx_ring->sbq, 0, rx_ring->sbq_len * sizeof(struct bq_desc));
	for (i = 0; i < rx_ring->sbq_len; i++) {
		sbq_desc = &rx_ring->sbq[i];
		memset(sbq_desc, 0, sizeof(*sbq_desc));
		sbq_desc->index = i;
		sbq_desc->addr = bq;
		bq++;
	}
}

static void ql_free_rx_resources(struct ql_adapter *qdev,
				 struct rx_ring *rx_ring)
{
	/* Free the small buffer queue. */
	if (rx_ring->sbq_base) {
		pci_free_consistent(qdev->pdev,
				    rx_ring->sbq_size,
				    rx_ring->sbq_base, rx_ring->sbq_base_dma);
		rx_ring->sbq_base = NULL;
	}

	/* Free the small buffer queue control blocks. */
	kfree(rx_ring->sbq);
	rx_ring->sbq = NULL;

	/* Free the large buffer queue. */
	if (rx_ring->lbq_base) {
		pci_free_consistent(qdev->pdev,
				    rx_ring->lbq_size,
				    rx_ring->lbq_base, rx_ring->lbq_base_dma);
		rx_ring->lbq_base = NULL;
	}

	/* Free the large buffer queue control blocks. */
	kfree(rx_ring->lbq);
	rx_ring->lbq = NULL;

	/* Free the rx queue. */
	if (rx_ring->cq_base) {
		pci_free_consistent(qdev->pdev,
				    rx_ring->cq_size,
				    rx_ring->cq_base, rx_ring->cq_base_dma);
		rx_ring->cq_base = NULL;
	}
}

/* Allocate queues and buffers for this completions queue based
 * on the values in the parameter structure. */
static int ql_alloc_rx_resources(struct ql_adapter *qdev,
				 struct rx_ring *rx_ring)
{

	/*
	 * Allocate the completion queue for this rx_ring.
	 */
	rx_ring->cq_base =
	    pci_alloc_consistent(qdev->pdev, rx_ring->cq_size,
				 &rx_ring->cq_base_dma);

	if (rx_ring->cq_base == NULL) {
		QPRINTK(qdev, IFUP, ERR, "rx_ring alloc failed.\n");
		return -ENOMEM;
	}

	if (rx_ring->sbq_len) {
		/*
		 * Allocate small buffer queue.
		 */
		rx_ring->sbq_base =
		    pci_alloc_consistent(qdev->pdev, rx_ring->sbq_size,
					 &rx_ring->sbq_base_dma);

		if (rx_ring->sbq_base == NULL) {
			QPRINTK(qdev, IFUP, ERR,
				"Small buffer queue allocation failed.\n");
			goto err_mem;
		}

		/*
		 * Allocate small buffer queue control blocks.
		 */
		rx_ring->sbq =
		    kmalloc(rx_ring->sbq_len * sizeof(struct bq_desc),
			    GFP_KERNEL);
		if (rx_ring->sbq == NULL) {
			QPRINTK(qdev, IFUP, ERR,
				"Small buffer queue control block allocation failed.\n");
			goto err_mem;
		}

		ql_init_sbq_ring(qdev, rx_ring);
	}

	if (rx_ring->lbq_len) {
		/*
		 * Allocate large buffer queue.
		 */
		rx_ring->lbq_base =
		    pci_alloc_consistent(qdev->pdev, rx_ring->lbq_size,
					 &rx_ring->lbq_base_dma);

		if (rx_ring->lbq_base == NULL) {
			QPRINTK(qdev, IFUP, ERR,
				"Large buffer queue allocation failed.\n");
			goto err_mem;
		}
		/*
		 * Allocate large buffer queue control blocks.
		 */
		rx_ring->lbq =
		    kmalloc(rx_ring->lbq_len * sizeof(struct bq_desc),
			    GFP_KERNEL);
		if (rx_ring->lbq == NULL) {
			QPRINTK(qdev, IFUP, ERR,
				"Large buffer queue control block allocation failed.\n");
			goto err_mem;
		}

		ql_init_lbq_ring(qdev, rx_ring);
	}

	return 0;

err_mem:
	ql_free_rx_resources(qdev, rx_ring);
	return -ENOMEM;
}

static void ql_tx_ring_clean(struct ql_adapter *qdev)
{
	struct tx_ring *tx_ring;
	struct tx_ring_desc *tx_ring_desc;
	int i, j;

	/*
	 * Loop through all queues and free
	 * any resources.
	 */
	for (j = 0; j < qdev->tx_ring_count; j++) {
		tx_ring = &qdev->tx_ring[j];
		for (i = 0; i < tx_ring->wq_len; i++) {
			tx_ring_desc = &tx_ring->q[i];
			if (tx_ring_desc && tx_ring_desc->skb) {
				QPRINTK(qdev, IFDOWN, ERR,
				"Freeing lost SKB %p, from queue %d, index %d.\n",
					tx_ring_desc->skb, j,
					tx_ring_desc->index);
				ql_unmap_send(qdev, tx_ring_desc,
					      tx_ring_desc->map_cnt);
				dev_kfree_skb(tx_ring_desc->skb);
				tx_ring_desc->skb = NULL;
			}
		}
	}
}

static void ql_free_mem_resources(struct ql_adapter *qdev)
{
	int i;

	for (i = 0; i < qdev->tx_ring_count; i++)
		ql_free_tx_resources(qdev, &qdev->tx_ring[i]);
	for (i = 0; i < qdev->rx_ring_count; i++)
		ql_free_rx_resources(qdev, &qdev->rx_ring[i]);
	ql_free_shadow_space(qdev);
}

static int ql_alloc_mem_resources(struct ql_adapter *qdev)
{
	int i;

	/* Allocate space for our shadow registers and such. */
	if (ql_alloc_shadow_space(qdev))
		return -ENOMEM;

	for (i = 0; i < qdev->rx_ring_count; i++) {
		if (ql_alloc_rx_resources(qdev, &qdev->rx_ring[i]) != 0) {
			QPRINTK(qdev, IFUP, ERR,
				"RX resource allocation failed.\n");
			goto err_mem;
		}
	}
	/* Allocate tx queue resources */
	for (i = 0; i < qdev->tx_ring_count; i++) {
		if (ql_alloc_tx_resources(qdev, &qdev->tx_ring[i]) != 0) {
			QPRINTK(qdev, IFUP, ERR,
				"TX resource allocation failed.\n");
			goto err_mem;
		}
	}
	return 0;

err_mem:
	ql_free_mem_resources(qdev);
	return -ENOMEM;
}

/* Set up the rx ring control block and pass it to the chip.
 * The control block is defined as
 * "Completion Queue Initialization Control Block", or cqicb.
 */
static int ql_start_rx_ring(struct ql_adapter *qdev, struct rx_ring *rx_ring)
{
	struct cqicb *cqicb = &rx_ring->cqicb;
	void *shadow_reg = qdev->rx_ring_shadow_reg_area +
		(rx_ring->cq_id * RX_RING_SHADOW_SPACE);
	u64 shadow_reg_dma = qdev->rx_ring_shadow_reg_dma +
		(rx_ring->cq_id * RX_RING_SHADOW_SPACE);
	void __iomem *doorbell_area =
	    qdev->doorbell_area + (DB_PAGE_SIZE * (128 + rx_ring->cq_id));
	int err = 0;
	u16 bq_len;
	u64 tmp;
	__le64 *base_indirect_ptr;
	int page_entries;

	/* Set up the shadow registers for this ring. */
	rx_ring->prod_idx_sh_reg = shadow_reg;
	rx_ring->prod_idx_sh_reg_dma = shadow_reg_dma;
	shadow_reg += sizeof(u64);
	shadow_reg_dma += sizeof(u64);
	rx_ring->lbq_base_indirect = shadow_reg;
	rx_ring->lbq_base_indirect_dma = shadow_reg_dma;
	shadow_reg += (sizeof(u64) * MAX_DB_PAGES_PER_BQ(rx_ring->lbq_len));
	shadow_reg_dma += (sizeof(u64) * MAX_DB_PAGES_PER_BQ(rx_ring->lbq_len));
	rx_ring->sbq_base_indirect = shadow_reg;
	rx_ring->sbq_base_indirect_dma = shadow_reg_dma;

	/* PCI doorbell mem area + 0x00 for consumer index register */
	rx_ring->cnsmr_idx_db_reg = (u32 __iomem *) doorbell_area;
	rx_ring->cnsmr_idx = 0;
	rx_ring->curr_entry = rx_ring->cq_base;

	/* PCI doorbell mem area + 0x04 for valid register */
	rx_ring->valid_db_reg = doorbell_area + 0x04;

	/* PCI doorbell mem area + 0x18 for large buffer consumer */
	rx_ring->lbq_prod_idx_db_reg = (u32 __iomem *) (doorbell_area + 0x18);

	/* PCI doorbell mem area + 0x1c */
	rx_ring->sbq_prod_idx_db_reg = (u32 __iomem *) (doorbell_area + 0x1c);

	memset((void *)cqicb, 0, sizeof(struct cqicb));
	cqicb->msix_vect = rx_ring->irq;

	bq_len = (rx_ring->cq_len == 65536) ? 0 : (u16) rx_ring->cq_len;
	cqicb->len = cpu_to_le16(bq_len | LEN_V | LEN_CPP_CONT);

	cqicb->addr = cpu_to_le64(rx_ring->cq_base_dma);

	cqicb->prod_idx_addr = cpu_to_le64(rx_ring->prod_idx_sh_reg_dma);

	/*
	 * Set up the control block load flags.
	 */
	cqicb->flags = FLAGS_LC |	/* Load queue base address */
	    FLAGS_LV |		/* Load MSI-X vector */
	    FLAGS_LI;		/* Load irq delay values */
	if (rx_ring->lbq_len) {
		cqicb->flags |= FLAGS_LL;	/* Load lbq values */
		tmp = (u64)rx_ring->lbq_base_dma;
		base_indirect_ptr = (__le64 *) rx_ring->lbq_base_indirect;
		page_entries = 0;
		do {
			*base_indirect_ptr = cpu_to_le64(tmp);
			tmp += DB_PAGE_SIZE;
			base_indirect_ptr++;
			page_entries++;
		} while (page_entries < MAX_DB_PAGES_PER_BQ(rx_ring->lbq_len));
		cqicb->lbq_addr =
		    cpu_to_le64(rx_ring->lbq_base_indirect_dma);
		bq_len = (rx_ring->lbq_buf_size == 65536) ? 0 :
			(u16) rx_ring->lbq_buf_size;
		cqicb->lbq_buf_size = cpu_to_le16(bq_len);
		bq_len = (rx_ring->lbq_len == 65536) ? 0 :
			(u16) rx_ring->lbq_len;
		cqicb->lbq_len = cpu_to_le16(bq_len);
		rx_ring->lbq_prod_idx = 0;
		rx_ring->lbq_curr_idx = 0;
		rx_ring->lbq_clean_idx = 0;
		rx_ring->lbq_free_cnt = rx_ring->lbq_len;
	}
	if (rx_ring->sbq_len) {
		cqicb->flags |= FLAGS_LS;	/* Load sbq values */
		tmp = (u64)rx_ring->sbq_base_dma;
		base_indirect_ptr = (__le64 *) rx_ring->sbq_base_indirect;
		page_entries = 0;
		do {
			*base_indirect_ptr = cpu_to_le64(tmp);
			tmp += DB_PAGE_SIZE;
			base_indirect_ptr++;
			page_entries++;
		} while (page_entries < MAX_DB_PAGES_PER_BQ(rx_ring->sbq_len));
		cqicb->sbq_addr =
		    cpu_to_le64(rx_ring->sbq_base_indirect_dma);
		cqicb->sbq_buf_size =
		    cpu_to_le16((u16)(rx_ring->sbq_buf_size/2));
		bq_len = (rx_ring->sbq_len == 65536) ? 0 :
			(u16) rx_ring->sbq_len;
		cqicb->sbq_len = cpu_to_le16(bq_len);
		rx_ring->sbq_prod_idx = 0;
		rx_ring->sbq_curr_idx = 0;
		rx_ring->sbq_clean_idx = 0;
		rx_ring->sbq_free_cnt = rx_ring->sbq_len;
	}
	switch (rx_ring->type) {
	case TX_Q:
		cqicb->irq_delay = cpu_to_le16(qdev->tx_coalesce_usecs);
		cqicb->pkt_delay = cpu_to_le16(qdev->tx_max_coalesced_frames);
		break;
	case RX_Q:
		/* Inbound completion handling rx_rings run in
		 * separate NAPI contexts.
		 */
		netif_napi_add(qdev->ndev, &rx_ring->napi, ql_napi_poll_msix,
			       64);
		cqicb->irq_delay = cpu_to_le16(qdev->rx_coalesce_usecs);
		cqicb->pkt_delay = cpu_to_le16(qdev->rx_max_coalesced_frames);
		break;
	default:
		QPRINTK(qdev, IFUP, DEBUG, "Invalid rx_ring->type = %d.\n",
			rx_ring->type);
	}
	QPRINTK(qdev, IFUP, DEBUG, "Initializing rx work queue.\n");
	err = ql_write_cfg(qdev, cqicb, sizeof(struct cqicb),
			   CFG_LCQ, rx_ring->cq_id);
	if (err) {
		QPRINTK(qdev, IFUP, ERR, "Failed to load CQICB.\n");
		return err;
	}
	return err;
}

static int ql_start_tx_ring(struct ql_adapter *qdev, struct tx_ring *tx_ring)
{
	struct wqicb *wqicb = (struct wqicb *)tx_ring;
	void __iomem *doorbell_area =
	    qdev->doorbell_area + (DB_PAGE_SIZE * tx_ring->wq_id);
	void *shadow_reg = qdev->tx_ring_shadow_reg_area +
	    (tx_ring->wq_id * sizeof(u64));
	u64 shadow_reg_dma = qdev->tx_ring_shadow_reg_dma +
	    (tx_ring->wq_id * sizeof(u64));
	int err = 0;

	/*
	 * Assign doorbell registers for this tx_ring.
	 */
	/* TX PCI doorbell mem area for tx producer index */
	tx_ring->prod_idx_db_reg = (u32 __iomem *) doorbell_area;
	tx_ring->prod_idx = 0;
	/* TX PCI doorbell mem area + 0x04 */
	tx_ring->valid_db_reg = doorbell_area + 0x04;

	/*
	 * Assign shadow registers for this tx_ring.
	 */
	tx_ring->cnsmr_idx_sh_reg = shadow_reg;
	tx_ring->cnsmr_idx_sh_reg_dma = shadow_reg_dma;

	wqicb->len = cpu_to_le16(tx_ring->wq_len | Q_LEN_V | Q_LEN_CPP_CONT);
	wqicb->flags = cpu_to_le16(Q_FLAGS_LC |
				   Q_FLAGS_LB | Q_FLAGS_LI | Q_FLAGS_LO);
	wqicb->cq_id_rss = cpu_to_le16(tx_ring->cq_id);
	wqicb->rid = 0;
	wqicb->addr = cpu_to_le64(tx_ring->wq_base_dma);

	wqicb->cnsmr_idx_addr = cpu_to_le64(tx_ring->cnsmr_idx_sh_reg_dma);

	ql_init_tx_ring(qdev, tx_ring);

	err = ql_write_cfg(qdev, wqicb, sizeof(*wqicb), CFG_LRQ,
			   (u16) tx_ring->wq_id);
	if (err) {
		QPRINTK(qdev, IFUP, ERR, "Failed to load tx_ring.\n");
		return err;
	}
	QPRINTK(qdev, IFUP, DEBUG, "Successfully loaded WQICB.\n");
	return err;
}

static void ql_disable_msix(struct ql_adapter *qdev)
{
	if (test_bit(QL_MSIX_ENABLED, &qdev->flags)) {
		pci_disable_msix(qdev->pdev);
		clear_bit(QL_MSIX_ENABLED, &qdev->flags);
		kfree(qdev->msi_x_entry);
		qdev->msi_x_entry = NULL;
	} else if (test_bit(QL_MSI_ENABLED, &qdev->flags)) {
		pci_disable_msi(qdev->pdev);
		clear_bit(QL_MSI_ENABLED, &qdev->flags);
	}
}

/* We start by trying to get the number of vectors
 * stored in qdev->intr_count. If we don't get that
 * many then we reduce the count and try again.
 */
static void ql_enable_msix(struct ql_adapter *qdev)
{
	int i, err;

	/* Get the MSIX vectors. */
	if (irq_type == MSIX_IRQ) {
		/* Try to alloc space for the msix struct,
		 * if it fails then go to MSI/legacy.
		 */
		qdev->msi_x_entry = kcalloc(qdev->intr_count,
					    sizeof(struct msix_entry),
					    GFP_KERNEL);
		if (!qdev->msi_x_entry) {
			irq_type = MSI_IRQ;
			goto msi;
		}

		for (i = 0; i < qdev->intr_count; i++)
			qdev->msi_x_entry[i].entry = i;

		/* Loop to get our vectors.  We start with
		 * what we want and settle for what we get.
		 */
		do {
			err = pci_enable_msix(qdev->pdev,
				qdev->msi_x_entry, qdev->intr_count);
			if (err > 0)
				qdev->intr_count = err;
		} while (err > 0);

		if (err < 0) {
			kfree(qdev->msi_x_entry);
			qdev->msi_x_entry = NULL;
			QPRINTK(qdev, IFUP, WARNING,
				"MSI-X Enable failed, trying MSI.\n");
			qdev->intr_count = 1;
			irq_type = MSI_IRQ;
		} else if (err == 0) {
			set_bit(QL_MSIX_ENABLED, &qdev->flags);
			QPRINTK(qdev, IFUP, INFO,
				"MSI-X Enabled, got %d vectors.\n",
				qdev->intr_count);
			return;
		}
	}
msi:
	qdev->intr_count = 1;
	if (irq_type == MSI_IRQ) {
		if (!pci_enable_msi(qdev->pdev)) {
			set_bit(QL_MSI_ENABLED, &qdev->flags);
			QPRINTK(qdev, IFUP, INFO,
				"Running with MSI interrupts.\n");
			return;
		}
	}
	irq_type = LEG_IRQ;
	QPRINTK(qdev, IFUP, DEBUG, "Running with legacy interrupts.\n");
}

/* Each vector services 1 RSS ring and and 1 or more
 * TX completion rings.  This function loops through
 * the TX completion rings and assigns the vector that
 * will service it.  An example would be if there are
 * 2 vectors (so 2 RSS rings) and 8 TX completion rings.
 * This would mean that vector 0 would service RSS ring 0
 * and TX competion rings 0,1,2 and 3.  Vector 1 would
 * service RSS ring 1 and TX completion rings 4,5,6 and 7.
 */
static void ql_set_tx_vect(struct ql_adapter *qdev)
{
	int i, j, vect;
	u32 tx_rings_per_vector = qdev->tx_ring_count / qdev->intr_count;

	if (likely(test_bit(QL_MSIX_ENABLED, &qdev->flags))) {
		/* Assign irq vectors to TX rx_rings.*/
		for (vect = 0, j = 0, i = qdev->rss_ring_count;
					 i < qdev->rx_ring_count; i++) {
			if (j == tx_rings_per_vector) {
				vect++;
				j = 0;
			}
			qdev->rx_ring[i].irq = vect;
			j++;
		}
	} else {
		/* For single vector all rings have an irq
		 * of zero.
		 */
		for (i = 0; i < qdev->rx_ring_count; i++)
			qdev->rx_ring[i].irq = 0;
	}
}

/* Set the interrupt mask for this vector.  Each vector
 * will service 1 RSS ring and 1 or more TX completion
 * rings.  This function sets up a bit mask per vector
 * that indicates which rings it services.
 */
static void ql_set_irq_mask(struct ql_adapter *qdev, struct intr_context *ctx)
{
	int j, vect = ctx->intr;
	u32 tx_rings_per_vector = qdev->tx_ring_count / qdev->intr_count;

	if (likely(test_bit(QL_MSIX_ENABLED, &qdev->flags))) {
		/* Add the RSS ring serviced by this vector
		 * to the mask.
		 */
		ctx->irq_mask = (1 << qdev->rx_ring[vect].cq_id);
		/* Add the TX ring(s) serviced by this vector
		 * to the mask. */
		for (j = 0; j < tx_rings_per_vector; j++) {
			ctx->irq_mask |=
			(1 << qdev->rx_ring[qdev->rss_ring_count +
			(vect * tx_rings_per_vector) + j].cq_id);
		}
	} else {
		/* For single vector we just shift each queue's
		 * ID into the mask.
		 */
		for (j = 0; j < qdev->rx_ring_count; j++)
			ctx->irq_mask |= (1 << qdev->rx_ring[j].cq_id);
	}
}

/*
 * Here we build the intr_context structures based on
 * our rx_ring count and intr vector count.
 * The intr_context structure is used to hook each vector
 * to possibly different handlers.
 */
static void ql_resolve_queues_to_irqs(struct ql_adapter *qdev)
{
	int i = 0;
	struct intr_context *intr_context = &qdev->intr_context[0];

	if (likely(test_bit(QL_MSIX_ENABLED, &qdev->flags))) {
		/* Each rx_ring has it's
		 * own intr_context since we have separate
		 * vectors for each queue.
		 */
		for (i = 0; i < qdev->intr_count; i++, intr_context++) {
			qdev->rx_ring[i].irq = i;
			intr_context->intr = i;
			intr_context->qdev = qdev;
			/* Set up this vector's bit-mask that indicates
			 * which queues it services.
			 */
			ql_set_irq_mask(qdev, intr_context);
			/*
			 * We set up each vectors enable/disable/read bits so
			 * there's no bit/mask calculations in the critical path.
			 */
			intr_context->intr_en_mask =
			    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK |
			    INTR_EN_TYPE_ENABLE | INTR_EN_IHD_MASK | INTR_EN_IHD
			    | i;
			intr_context->intr_dis_mask =
			    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK |
			    INTR_EN_TYPE_DISABLE | INTR_EN_IHD_MASK |
			    INTR_EN_IHD | i;
			intr_context->intr_read_mask =
			    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK |
			    INTR_EN_TYPE_READ | INTR_EN_IHD_MASK | INTR_EN_IHD |
			    i;
			if (i == 0) {
				/* The first vector/queue handles
				 * broadcast/multicast, fatal errors,
				 * and firmware events.  This in addition
				 * to normal inbound NAPI processing.
				 */
				intr_context->handler = qlge_isr;
				sprintf(intr_context->name, "%s-rx-%d",
					qdev->ndev->name, i);
			} else {
				/*
				 * Inbound queues handle unicast frames only.
				 */
				intr_context->handler = qlge_msix_rx_isr;
				sprintf(intr_context->name, "%s-rx-%d",
					qdev->ndev->name, i);
			}
		}
	} else {
		/*
		 * All rx_rings use the same intr_context since
		 * there is only one vector.
		 */
		intr_context->intr = 0;
		intr_context->qdev = qdev;
		/*
		 * We set up each vectors enable/disable/read bits so
		 * there's no bit/mask calculations in the critical path.
		 */
		intr_context->intr_en_mask =
		    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK | INTR_EN_TYPE_ENABLE;
		intr_context->intr_dis_mask =
		    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK |
		    INTR_EN_TYPE_DISABLE;
		intr_context->intr_read_mask =
		    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK | INTR_EN_TYPE_READ;
		/*
		 * Single interrupt means one handler for all rings.
		 */
		intr_context->handler = qlge_isr;
		sprintf(intr_context->name, "%s-single_irq", qdev->ndev->name);
		/* Set up this vector's bit-mask that indicates
		 * which queues it services. In this case there is
		 * a single vector so it will service all RSS and
		 * TX completion rings.
		 */
		ql_set_irq_mask(qdev, intr_context);
	}
	/* Tell the TX completion rings which MSIx vector
	 * they will be using.
	 */
	ql_set_tx_vect(qdev);
}

static void ql_free_irq(struct ql_adapter *qdev)
{
	int i;
	struct intr_context *intr_context = &qdev->intr_context[0];

	for (i = 0; i < qdev->intr_count; i++, intr_context++) {
		if (intr_context->hooked) {
			if (test_bit(QL_MSIX_ENABLED, &qdev->flags)) {
				free_irq(qdev->msi_x_entry[i].vector,
					 &qdev->rx_ring[i]);
				QPRINTK(qdev, IFDOWN, DEBUG,
					"freeing msix interrupt %d.\n", i);
			} else {
				free_irq(qdev->pdev->irq, &qdev->rx_ring[0]);
				QPRINTK(qdev, IFDOWN, DEBUG,
					"freeing msi interrupt %d.\n", i);
			}
		}
	}
	ql_disable_msix(qdev);
}

static int ql_request_irq(struct ql_adapter *qdev)
{
	int i;
	int status = 0;
	struct pci_dev *pdev = qdev->pdev;
	struct intr_context *intr_context = &qdev->intr_context[0];

	ql_resolve_queues_to_irqs(qdev);

	for (i = 0; i < qdev->intr_count; i++, intr_context++) {
		atomic_set(&intr_context->irq_cnt, 0);
		if (test_bit(QL_MSIX_ENABLED, &qdev->flags)) {
			status = request_irq(qdev->msi_x_entry[i].vector,
					     intr_context->handler,
					     0,
					     intr_context->name,
					     &qdev->rx_ring[i]);
			if (status) {
				QPRINTK(qdev, IFUP, ERR,
					"Failed request for MSIX interrupt %d.\n",
					i);
				goto err_irq;
			} else {
				QPRINTK(qdev, IFUP, DEBUG,
					"Hooked intr %d, queue type %s%s%s, with name %s.\n",
					i,
					qdev->rx_ring[i].type ==
					DEFAULT_Q ? "DEFAULT_Q" : "",
					qdev->rx_ring[i].type ==
					TX_Q ? "TX_Q" : "",
					qdev->rx_ring[i].type ==
					RX_Q ? "RX_Q" : "", intr_context->name);
			}
		} else {
			QPRINTK(qdev, IFUP, DEBUG,
				"trying msi or legacy interrupts.\n");
			QPRINTK(qdev, IFUP, DEBUG,
				"%s: irq = %d.\n", __func__, pdev->irq);
			QPRINTK(qdev, IFUP, DEBUG,
				"%s: context->name = %s.\n", __func__,
			       intr_context->name);
			QPRINTK(qdev, IFUP, DEBUG,
				"%s: dev_id = 0x%p.\n", __func__,
			       &qdev->rx_ring[0]);
			status =
			    request_irq(pdev->irq, qlge_isr,
					test_bit(QL_MSI_ENABLED,
						 &qdev->
						 flags) ? 0 : IRQF_SHARED,
					intr_context->name, &qdev->rx_ring[0]);
			if (status)
				goto err_irq;

			QPRINTK(qdev, IFUP, ERR,
				"Hooked intr %d, queue type %s%s%s, with name %s.\n",
				i,
				qdev->rx_ring[0].type ==
				DEFAULT_Q ? "DEFAULT_Q" : "",
				qdev->rx_ring[0].type == TX_Q ? "TX_Q" : "",
				qdev->rx_ring[0].type == RX_Q ? "RX_Q" : "",
				intr_context->name);
		}
		intr_context->hooked = 1;
	}
	return status;
err_irq:
	QPRINTK(qdev, IFUP, ERR, "Failed to get the interrupts!!!/n");
	ql_free_irq(qdev);
	return status;
}

static int ql_start_rss(struct ql_adapter *qdev)
{
	u8 init_hash_seed[] = {0x6d, 0x5a, 0x56, 0xda, 0x25, 0x5b, 0x0e, 0xc2,
				0x41, 0x67, 0x25, 0x3d, 0x43, 0xa3, 0x8f,
				0xb0, 0xd0, 0xca, 0x2b, 0xcb, 0xae, 0x7b,
				0x30, 0xb4, 0x77, 0xcb, 0x2d, 0xa3, 0x80,
				0x30, 0xf2, 0x0c, 0x6a, 0x42, 0xb7, 0x3b,
				0xbe, 0xac, 0x01, 0xfa};
	struct ricb *ricb = &qdev->ricb;
	int status = 0;
	int i;
	u8 *hash_id = (u8 *) ricb->hash_cq_id;

	memset((void *)ricb, 0, sizeof(*ricb));

	ricb->base_cq = RSS_L4K;
	ricb->flags =
		(RSS_L6K | RSS_LI | RSS_LB | RSS_LM | RSS_RT4 | RSS_RT6);
	ricb->mask = cpu_to_le16((u16)(0x3ff));

	/*
	 * Fill out the Indirection Table.
	 */
	for (i = 0; i < 1024; i++)
		hash_id[i] = (i & (qdev->rss_ring_count - 1));

	memcpy((void *)&ricb->ipv6_hash_key[0], init_hash_seed, 40);
	memcpy((void *)&ricb->ipv4_hash_key[0], init_hash_seed, 16);

	QPRINTK(qdev, IFUP, DEBUG, "Initializing RSS.\n");

	status = ql_write_cfg(qdev, ricb, sizeof(*ricb), CFG_LR, 0);
	if (status) {
		QPRINTK(qdev, IFUP, ERR, "Failed to load RICB.\n");
		return status;
	}
	QPRINTK(qdev, IFUP, DEBUG, "Successfully loaded RICB.\n");
	return status;
}

static int ql_clear_routing_entries(struct ql_adapter *qdev)
{
	int i, status = 0;

	status = ql_sem_spinlock(qdev, SEM_RT_IDX_MASK);
	if (status)
		return status;
	/* Clear all the entries in the routing table. */
	for (i = 0; i < 16; i++) {
		status = ql_set_routing_reg(qdev, i, 0, 0);
		if (status) {
			QPRINTK(qdev, IFUP, ERR,
				"Failed to init routing register for CAM "
				"packets.\n");
			break;
		}
	}
	ql_sem_unlock(qdev, SEM_RT_IDX_MASK);
	return status;
}

/* Initialize the frame-to-queue routing. */
static int ql_route_initialize(struct ql_adapter *qdev)
{
	int status = 0;

	/* Clear all the entries in the routing table. */
	status = ql_clear_routing_entries(qdev);
	if (status)
		return status;

	status = ql_sem_spinlock(qdev, SEM_RT_IDX_MASK);
	if (status)
		return status;

	status = ql_set_routing_reg(qdev, RT_IDX_ALL_ERR_SLOT, RT_IDX_ERR, 1);
	if (status) {
		QPRINTK(qdev, IFUP, ERR,
			"Failed to init routing register for error packets.\n");
		goto exit;
	}
	status = ql_set_routing_reg(qdev, RT_IDX_BCAST_SLOT, RT_IDX_BCAST, 1);
	if (status) {
		QPRINTK(qdev, IFUP, ERR,
			"Failed to init routing register for broadcast packets.\n");
		goto exit;
	}
	/* If we have more than one inbound queue, then turn on RSS in the
	 * routing block.
	 */
	if (qdev->rss_ring_count > 1) {
		status = ql_set_routing_reg(qdev, RT_IDX_RSS_MATCH_SLOT,
					RT_IDX_RSS_MATCH, 1);
		if (status) {
			QPRINTK(qdev, IFUP, ERR,
				"Failed to init routing register for MATCH RSS packets.\n");
			goto exit;
		}
	}

	status = ql_set_routing_reg(qdev, RT_IDX_CAM_HIT_SLOT,
				    RT_IDX_CAM_HIT, 1);
	if (status)
		QPRINTK(qdev, IFUP, ERR,
			"Failed to init routing register for CAM packets.\n");
exit:
	ql_sem_unlock(qdev, SEM_RT_IDX_MASK);
	return status;
}

int ql_cam_route_initialize(struct ql_adapter *qdev)
{
	int status, set;

	/* If check if the link is up and use to
	 * determine if we are setting or clearing
	 * the MAC address in the CAM.
	 */
	set = ql_read32(qdev, STS);
	set &= qdev->port_link_up;
	status = ql_set_mac_addr(qdev, set);
	if (status) {
		QPRINTK(qdev, IFUP, ERR, "Failed to init mac address.\n");
		return status;
	}

	status = ql_route_initialize(qdev);
	if (status)
		QPRINTK(qdev, IFUP, ERR, "Failed to init routing table.\n");

	return status;
}

static int ql_adapter_initialize(struct ql_adapter *qdev)
{
	u32 value, mask;
	int i;
	int status = 0;

	/*
	 * Set up the System register to halt on errors.
	 */
	value = SYS_EFE | SYS_FAE;
	mask = value << 16;
	ql_write32(qdev, SYS, mask | value);

	/* Set the default queue, and VLAN behavior. */
	value = NIC_RCV_CFG_DFQ | NIC_RCV_CFG_RV;
	mask = NIC_RCV_CFG_DFQ_MASK | (NIC_RCV_CFG_RV << 16);
	ql_write32(qdev, NIC_RCV_CFG, (mask | value));

	/* Set the MPI interrupt to enabled. */
	ql_write32(qdev, INTR_MASK, (INTR_MASK_PI << 16) | INTR_MASK_PI);

	/* Enable the function, set pagesize, enable error checking. */
	value = FSC_FE | FSC_EPC_INBOUND | FSC_EPC_OUTBOUND |
	    FSC_EC | FSC_VM_PAGE_4K | FSC_SH;

	/* Set/clear header splitting. */
	mask = FSC_VM_PAGESIZE_MASK |
	    FSC_DBL_MASK | FSC_DBRST_MASK | (value << 16);
	ql_write32(qdev, FSC, mask | value);

	ql_write32(qdev, SPLT_HDR, SPLT_HDR_EP |
		min(SMALL_BUFFER_SIZE, MAX_SPLIT_SIZE));

	/* Set RX packet routing to use port/pci function on which the
	 * packet arrived on in addition to usual frame routing.
	 * This is helpful on bonding where both interfaces can have
	 * the same MAC address.
	 */
	ql_write32(qdev, RST_FO, RST_FO_RR_MASK | RST_FO_RR_RCV_FUNC_CQ);

	/* Start up the rx queues. */
	for (i = 0; i < qdev->rx_ring_count; i++) {
		status = ql_start_rx_ring(qdev, &qdev->rx_ring[i]);
		if (status) {
			QPRINTK(qdev, IFUP, ERR,
				"Failed to start rx ring[%d].\n", i);
			return status;
		}
	}

	/* If there is more than one inbound completion queue
	 * then download a RICB to configure RSS.
	 */
	if (qdev->rss_ring_count > 1) {
		status = ql_start_rss(qdev);
		if (status) {
			QPRINTK(qdev, IFUP, ERR, "Failed to start RSS.\n");
			return status;
		}
	}

	/* Start up the tx queues. */
	for (i = 0; i < qdev->tx_ring_count; i++) {
		status = ql_start_tx_ring(qdev, &qdev->tx_ring[i]);
		if (status) {
			QPRINTK(qdev, IFUP, ERR,
				"Failed to start tx ring[%d].\n", i);
			return status;
		}
	}

	/* Initialize the port and set the max framesize. */
	status = qdev->nic_ops->port_initialize(qdev);
       if (status) {
              QPRINTK(qdev, IFUP, ERR, "Failed to start port.\n");
              return status;
       }

	/* Set up the MAC address and frame routing filter. */
	status = ql_cam_route_initialize(qdev);
	if (status) {
		QPRINTK(qdev, IFUP, ERR,
				"Failed to init CAM/Routing tables.\n");
		return status;
	}

	/* Start NAPI for the RSS queues. */
	for (i = 0; i < qdev->rss_ring_count; i++) {
		QPRINTK(qdev, IFUP, DEBUG, "Enabling NAPI for rx_ring[%d].\n",
			i);
		napi_enable(&qdev->rx_ring[i].napi);
	}

	return status;
}

/* Issue soft reset to chip. */
static int ql_adapter_reset(struct ql_adapter *qdev)
{
	u32 value;
	int status = 0;
	unsigned long end_jiffies;

	/* Clear all the entries in the routing table. */
	status = ql_clear_routing_entries(qdev);
	if (status) {
		QPRINTK(qdev, IFUP, ERR, "Failed to clear routing bits.\n");
		return status;
	}

	end_jiffies = jiffies +
		max((unsigned long)1, usecs_to_jiffies(30));

	/* Stop management traffic. */
	ql_mb_set_mgmnt_traffic_ctl(qdev, MB_SET_MPI_TFK_STOP);

	/* Wait for the NIC and MGMNT FIFOs to empty. */
	ql_wait_fifo_empty(qdev);

	ql_write32(qdev, RST_FO, (RST_FO_FR << 16) | RST_FO_FR);

	do {
		value = ql_read32(qdev, RST_FO);
		if ((value & RST_FO_FR) == 0)
			break;
		cpu_relax();
	} while (time_before(jiffies, end_jiffies));

	if (value & RST_FO_FR) {
		QPRINTK(qdev, IFDOWN, ERR,
			"ETIMEDOUT!!! errored out of resetting the chip!\n");
		status = -ETIMEDOUT;
	}

	/* Resume management traffic. */
	ql_mb_set_mgmnt_traffic_ctl(qdev, MB_SET_MPI_TFK_RESUME);
	return status;
}

static void ql_display_dev_info(struct net_device *ndev)
{
	struct ql_adapter *qdev = (struct ql_adapter *)netdev_priv(ndev);

	QPRINTK(qdev, PROBE, INFO,
		"Function #%d, Port %d, NIC Roll %d, NIC Rev = %d, "
		"XG Roll = %d, XG Rev = %d.\n",
		qdev->func,
		qdev->port,
		qdev->chip_rev_id & 0x0000000f,
		qdev->chip_rev_id >> 4 & 0x0000000f,
		qdev->chip_rev_id >> 8 & 0x0000000f,
		qdev->chip_rev_id >> 12 & 0x0000000f);
	QPRINTK(qdev, PROBE, INFO, "MAC address %pM\n", ndev->dev_addr);
}

static int ql_adapter_down(struct ql_adapter *qdev)
{
	int i, status = 0;

	ql_link_off(qdev);

	/* Don't kill the reset worker thread if we
	 * are in the process of recovery.
	 */
	if (test_bit(QL_ADAPTER_UP, &qdev->flags))
		cancel_delayed_work_sync(&qdev->asic_reset_work);
	cancel_delayed_work_sync(&qdev->mpi_reset_work);
	cancel_delayed_work_sync(&qdev->mpi_work);
	cancel_delayed_work_sync(&qdev->mpi_idc_work);
	cancel_delayed_work_sync(&qdev->mpi_port_cfg_work);

	for (i = 0; i < qdev->rss_ring_count; i++)
		napi_disable(&qdev->rx_ring[i].napi);

	clear_bit(QL_ADAPTER_UP, &qdev->flags);

	ql_disable_interrupts(qdev);

	ql_tx_ring_clean(qdev);

	/* Call netif_napi_del() from common point.
	 */
	for (i = 0; i < qdev->rss_ring_count; i++)
		netif_napi_del(&qdev->rx_ring[i].napi);

	ql_free_rx_buffers(qdev);

	status = ql_adapter_reset(qdev);
	if (status)
		QPRINTK(qdev, IFDOWN, ERR, "reset(func #%d) FAILED!\n",
			qdev->func);
	return status;
}

static int ql_adapter_up(struct ql_adapter *qdev)
{
	int err = 0;

	err = ql_adapter_initialize(qdev);
	if (err) {
		QPRINTK(qdev, IFUP, INFO, "Unable to initialize adapter.\n");
		goto err_init;
	}
	set_bit(QL_ADAPTER_UP, &qdev->flags);
	ql_alloc_rx_buffers(qdev);
	/* If the port is initialized and the
	 * link is up the turn on the carrier.
	 */
	if ((ql_read32(qdev, STS) & qdev->port_init) &&
			(ql_read32(qdev, STS) & qdev->port_link_up))
		ql_link_on(qdev);
	ql_enable_interrupts(qdev);
	ql_enable_all_completion_interrupts(qdev);
	netif_tx_start_all_queues(qdev->ndev);

	return 0;
err_init:
	ql_adapter_reset(qdev);
	return err;
}

static void ql_release_adapter_resources(struct ql_adapter *qdev)
{
	ql_free_mem_resources(qdev);
	ql_free_irq(qdev);
}

static int ql_get_adapter_resources(struct ql_adapter *qdev)
{
	int status = 0;

	if (ql_alloc_mem_resources(qdev)) {
		QPRINTK(qdev, IFUP, ERR, "Unable to  allocate memory.\n");
		return -ENOMEM;
	}
	status = ql_request_irq(qdev);
	return status;
}

static int qlge_close(struct net_device *ndev)
{
	struct ql_adapter *qdev = netdev_priv(ndev);

	/*
	 * Wait for device to recover from a reset.
	 * (Rarely happens, but possible.)
	 */
	while (!test_bit(QL_ADAPTER_UP, &qdev->flags))
		msleep(1);
	ql_adapter_down(qdev);
	ql_release_adapter_resources(qdev);
	return 0;
}

static int ql_configure_rings(struct ql_adapter *qdev)
{
	int i;
	struct rx_ring *rx_ring;
	struct tx_ring *tx_ring;
	int cpu_cnt = min(MAX_CPUS, (int)num_online_cpus());

	/* In a perfect world we have one RSS ring for each CPU
	 * and each has it's own vector.  To do that we ask for
	 * cpu_cnt vectors.  ql_enable_msix() will adjust the
	 * vector count to what we actually get.  We then
	 * allocate an RSS ring for each.
	 * Essentially, we are doing min(cpu_count, msix_vector_count).
	 */
	qdev->intr_count = cpu_cnt;
	ql_enable_msix(qdev);
	/* Adjust the RSS ring count to the actual vector count. */
	qdev->rss_ring_count = qdev->intr_count;
	qdev->tx_ring_count = cpu_cnt;
	qdev->rx_ring_count = qdev->tx_ring_count + qdev->rss_ring_count;

	for (i = 0; i < qdev->tx_ring_count; i++) {
		tx_ring = &qdev->tx_ring[i];
		memset((void *)tx_ring, 0, sizeof(*tx_ring));
		tx_ring->qdev = qdev;
		tx_ring->wq_id = i;
		tx_ring->wq_len = qdev->tx_ring_size;
		tx_ring->wq_size =
		    tx_ring->wq_len * sizeof(struct ob_mac_iocb_req);

		/*
		 * The completion queue ID for the tx rings start
		 * immediately after the rss rings.
		 */
		tx_ring->cq_id = qdev->rss_ring_count + i;
	}

	for (i = 0; i < qdev->rx_ring_count; i++) {
		rx_ring = &qdev->rx_ring[i];
		memset((void *)rx_ring, 0, sizeof(*rx_ring));
		rx_ring->qdev = qdev;
		rx_ring->cq_id = i;
		rx_ring->cpu = i % cpu_cnt;	/* CPU to run handler on. */
		if (i < qdev->rss_ring_count) {
			/*
			 * Inbound (RSS) queues.
			 */
			rx_ring->cq_len = qdev->rx_ring_size;
			rx_ring->cq_size =
			    rx_ring->cq_len * sizeof(struct ql_net_rsp_iocb);
			rx_ring->lbq_len = NUM_LARGE_BUFFERS;
			rx_ring->lbq_size =
			    rx_ring->lbq_len * sizeof(__le64);
			rx_ring->lbq_buf_size = LARGE_BUFFER_SIZE;
			rx_ring->sbq_len = NUM_SMALL_BUFFERS;
			rx_ring->sbq_size =
			    rx_ring->sbq_len * sizeof(__le64);
			rx_ring->sbq_buf_size = SMALL_BUFFER_SIZE * 2;
			rx_ring->type = RX_Q;
		} else {
			/*
			 * Outbound queue handles outbound completions only.
			 */
			/* outbound cq is same size as tx_ring it services. */
			rx_ring->cq_len = qdev->tx_ring_size;
			rx_ring->cq_size =
			    rx_ring->cq_len * sizeof(struct ql_net_rsp_iocb);
			rx_ring->lbq_len = 0;
			rx_ring->lbq_size = 0;
			rx_ring->lbq_buf_size = 0;
			rx_ring->sbq_len = 0;
			rx_ring->sbq_size = 0;
			rx_ring->sbq_buf_size = 0;
			rx_ring->type = TX_Q;
		}
	}
	return 0;
}

static int qlge_open(struct net_device *ndev)
{
	int err = 0;
	struct ql_adapter *qdev = netdev_priv(ndev);

	err = ql_configure_rings(qdev);
	if (err)
		return err;

	err = ql_get_adapter_resources(qdev);
	if (err)
		goto error_up;

	err = ql_adapter_up(qdev);
	if (err)
		goto error_up;

	return err;

error_up:
	ql_release_adapter_resources(qdev);
	return err;
}

static int qlge_change_mtu(struct net_device *ndev, int new_mtu)
{
	struct ql_adapter *qdev = netdev_priv(ndev);

	if (ndev->mtu == 1500 && new_mtu == 9000) {
		QPRINTK(qdev, IFUP, ERR, "Changing to jumbo MTU.\n");
		queue_delayed_work(qdev->workqueue,
				&qdev->mpi_port_cfg_work, 0);
	} else if (ndev->mtu == 9000 && new_mtu == 1500) {
		QPRINTK(qdev, IFUP, ERR, "Changing to normal MTU.\n");
	} else if ((ndev->mtu == 1500 && new_mtu == 1500) ||
		   (ndev->mtu == 9000 && new_mtu == 9000)) {
		return 0;
	} else
		return -EINVAL;
	ndev->mtu = new_mtu;
	return 0;
}

static struct net_device_stats *qlge_get_stats(struct net_device
					       *ndev)
{
	struct ql_adapter *qdev = netdev_priv(ndev);
	return &qdev->stats;
}

static void qlge_set_multicast_list(struct net_device *ndev)
{
	struct ql_adapter *qdev = (struct ql_adapter *)netdev_priv(ndev);
	struct dev_mc_list *mc_ptr;
	int i, status;

	status = ql_sem_spinlock(qdev, SEM_RT_IDX_MASK);
	if (status)
		return;
	/*
	 * Set or clear promiscuous mode if a
	 * transition is taking place.
	 */
	if (ndev->flags & IFF_PROMISC) {
		if (!test_bit(QL_PROMISCUOUS, &qdev->flags)) {
			if (ql_set_routing_reg
			    (qdev, RT_IDX_PROMISCUOUS_SLOT, RT_IDX_VALID, 1)) {
				QPRINTK(qdev, HW, ERR,
					"Failed to set promiscous mode.\n");
			} else {
				set_bit(QL_PROMISCUOUS, &qdev->flags);
			}
		}
	} else {
		if (test_bit(QL_PROMISCUOUS, &qdev->flags)) {
			if (ql_set_routing_reg
			    (qdev, RT_IDX_PROMISCUOUS_SLOT, RT_IDX_VALID, 0)) {
				QPRINTK(qdev, HW, ERR,
					"Failed to clear promiscous mode.\n");
			} else {
				clear_bit(QL_PROMISCUOUS, &qdev->flags);
			}
		}
	}

	/*
	 * Set or clear all multicast mode if a
	 * transition is taking place.
	 */
	if ((ndev->flags & IFF_ALLMULTI) ||
	    (ndev->mc_count > MAX_MULTICAST_ENTRIES)) {
		if (!test_bit(QL_ALLMULTI, &qdev->flags)) {
			if (ql_set_routing_reg
			    (qdev, RT_IDX_ALLMULTI_SLOT, RT_IDX_MCAST, 1)) {
				QPRINTK(qdev, HW, ERR,
					"Failed to set all-multi mode.\n");
			} else {
				set_bit(QL_ALLMULTI, &qdev->flags);
			}
		}
	} else {
		if (test_bit(QL_ALLMULTI, &qdev->flags)) {
			if (ql_set_routing_reg
			    (qdev, RT_IDX_ALLMULTI_SLOT, RT_IDX_MCAST, 0)) {
				QPRINTK(qdev, HW, ERR,
					"Failed to clear all-multi mode.\n");
			} else {
				clear_bit(QL_ALLMULTI, &qdev->flags);
			}
		}
	}

	if (ndev->mc_count) {
		status = ql_sem_spinlock(qdev, SEM_MAC_ADDR_MASK);
		if (status)
			goto exit;
		for (i = 0, mc_ptr = ndev->mc_list; mc_ptr;
		     i++, mc_ptr = mc_ptr->next)
			if (ql_set_mac_addr_reg(qdev, (u8 *) mc_ptr->dmi_addr,
						MAC_ADDR_TYPE_MULTI_MAC, i)) {
				QPRINTK(qdev, HW, ERR,
					"Failed to loadmulticast address.\n");
				ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK);
				goto exit;
			}
		ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK);
		if (ql_set_routing_reg
		    (qdev, RT_IDX_MCAST_MATCH_SLOT, RT_IDX_MCAST_MATCH, 1)) {
			QPRINTK(qdev, HW, ERR,
				"Failed to set multicast match mode.\n");
		} else {
			set_bit(QL_ALLMULTI, &qdev->flags);
		}
	}
exit:
	ql_sem_unlock(qdev, SEM_RT_IDX_MASK);
}

static int qlge_set_mac_address(struct net_device *ndev, void *p)
{
	struct ql_adapter *qdev = (struct ql_adapter *)netdev_priv(ndev);
	struct sockaddr *addr = p;
	int status;

	if (netif_running(ndev))
		return -EBUSY;

	if (!is_valid_ether_addr(addr->sa_data))
		return -EADDRNOTAVAIL;
	memcpy(ndev->dev_addr, addr->sa_data, ndev->addr_len);

	status = ql_sem_spinlock(qdev, SEM_MAC_ADDR_MASK);
	if (status)
		return status;
	status = ql_set_mac_addr_reg(qdev, (u8 *) ndev->dev_addr,
			MAC_ADDR_TYPE_CAM_MAC, qdev->func * MAX_CQ);
	if (status)
		QPRINTK(qdev, HW, ERR, "Failed to load MAC address.\n");
	ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK);
	return status;
}

static void qlge_tx_timeout(struct net_device *ndev)
{
	struct ql_adapter *qdev = (struct ql_adapter *)netdev_priv(ndev);
	ql_queue_asic_error(qdev);
}

static void ql_asic_reset_work(struct work_struct *work)
{
	struct ql_adapter *qdev =
	    container_of(work, struct ql_adapter, asic_reset_work.work);
	int status;
	rtnl_lock();
	status = ql_adapter_down(qdev);
	if (status)
		goto error;

	status = ql_adapter_up(qdev);
	if (status)
		goto error;

	/* Restore rx mode. */
	clear_bit(QL_ALLMULTI, &qdev->flags);
	clear_bit(QL_PROMISCUOUS, &qdev->flags);
	qlge_set_multicast_list(qdev->ndev);

	rtnl_unlock();
	return;
error:
	QPRINTK(qdev, IFUP, ALERT,
		"Driver up/down cycle failed, closing device\n");

	set_bit(QL_ADAPTER_UP, &qdev->flags);
	dev_close(qdev->ndev);
	rtnl_unlock();
}

static struct nic_operations qla8012_nic_ops = {
	.get_flash		= ql_get_8012_flash_params,
	.port_initialize	= ql_8012_port_initialize,
};

static struct nic_operations qla8000_nic_ops = {
	.get_flash		= ql_get_8000_flash_params,
	.port_initialize	= ql_8000_port_initialize,
};

/* Find the pcie function number for the other NIC
 * on this chip.  Since both NIC functions share a
 * common firmware we have the lowest enabled function
 * do any common work.  Examples would be resetting
 * after a fatal firmware error, or doing a firmware
 * coredump.
 */
static int ql_get_alt_pcie_func(struct ql_adapter *qdev)
{
	int status = 0;
	u32 temp;
	u32 nic_func1, nic_func2;

	status = ql_read_mpi_reg(qdev, MPI_TEST_FUNC_PORT_CFG,
			&temp);
	if (status)
		return status;

	nic_func1 = ((temp >> MPI_TEST_NIC1_FUNC_SHIFT) &
			MPI_TEST_NIC_FUNC_MASK);
	nic_func2 = ((temp >> MPI_TEST_NIC2_FUNC_SHIFT) &
			MPI_TEST_NIC_FUNC_MASK);

	if (qdev->func == nic_func1)
		qdev->alt_func = nic_func2;
	else if (qdev->func == nic_func2)
		qdev->alt_func = nic_func1;
	else
		status = -EIO;

	return status;
}

static int ql_get_board_info(struct ql_adapter *qdev)
{
	int status;
	qdev->func =
	    (ql_read32(qdev, STS) & STS_FUNC_ID_MASK) >> STS_FUNC_ID_SHIFT;
	if (qdev->func > 3)
		return -EIO;

	status = ql_get_alt_pcie_func(qdev);
	if (status)
		return status;

	qdev->port = (qdev->func < qdev->alt_func) ? 0 : 1;
	if (qdev->port) {
		qdev->xg_sem_mask = SEM_XGMAC1_MASK;
		qdev->port_link_up = STS_PL1;
		qdev->port_init = STS_PI1;
		qdev->mailbox_in = PROC_ADDR_MPI_RISC | PROC_ADDR_FUNC2_MBI;
		qdev->mailbox_out = PROC_ADDR_MPI_RISC | PROC_ADDR_FUNC2_MBO;
	} else {
		qdev->xg_sem_mask = SEM_XGMAC0_MASK;
		qdev->port_link_up = STS_PL0;
		qdev->port_init = STS_PI0;
		qdev->mailbox_in = PROC_ADDR_MPI_RISC | PROC_ADDR_FUNC0_MBI;
		qdev->mailbox_out = PROC_ADDR_MPI_RISC | PROC_ADDR_FUNC0_MBO;
	}
	qdev->chip_rev_id = ql_read32(qdev, REV_ID);
	qdev->device_id = qdev->pdev->device;
	if (qdev->device_id == QLGE_DEVICE_ID_8012)
		qdev->nic_ops = &qla8012_nic_ops;
	else if (qdev->device_id == QLGE_DEVICE_ID_8000)
		qdev->nic_ops = &qla8000_nic_ops;
	return status;
}

static void ql_release_all(struct pci_dev *pdev)
{
	struct net_device *ndev = pci_get_drvdata(pdev);
	struct ql_adapter *qdev = netdev_priv(ndev);

	if (qdev->workqueue) {
		destroy_workqueue(qdev->workqueue);
		qdev->workqueue = NULL;
	}

	if (qdev->reg_base)
		iounmap(qdev->reg_base);
	if (qdev->doorbell_area)
		iounmap(qdev->doorbell_area);
	pci_release_regions(pdev);
	pci_set_drvdata(pdev, NULL);
}

static int __devinit ql_init_device(struct pci_dev *pdev,
				    struct net_device *ndev, int cards_found)
{
	struct ql_adapter *qdev = netdev_priv(ndev);
	int pos, err = 0;
	u16 val16;

	memset((void *)qdev, 0, sizeof(*qdev));
	err = pci_enable_device(pdev);
	if (err) {
		dev_err(&pdev->dev, "PCI device enable failed.\n");
		return err;
	}

	qdev->ndev = ndev;
	qdev->pdev = pdev;
	pci_set_drvdata(pdev, ndev);
	pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
	if (pos <= 0) {
		dev_err(&pdev->dev, PFX "Cannot find PCI Express capability, "
			"aborting.\n");
		return pos;
	} else {
		pci_read_config_word(pdev, pos + PCI_EXP_DEVCTL, &val16);
		val16 &= ~PCI_EXP_DEVCTL_NOSNOOP_EN;
		val16 |= (PCI_EXP_DEVCTL_CERE |
			  PCI_EXP_DEVCTL_NFERE |
			  PCI_EXP_DEVCTL_FERE | PCI_EXP_DEVCTL_URRE);
		pci_write_config_word(pdev, pos + PCI_EXP_DEVCTL, val16);
	}

	err = pci_request_regions(pdev, DRV_NAME);
	if (err) {
		dev_err(&pdev->dev, "PCI region request failed.\n");
		return err;
	}

	pci_set_master(pdev);
	if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
		set_bit(QL_DMA64, &qdev->flags);
		err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
	} else {
		err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
		if (!err)
		       err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
	}

	if (err) {
		dev_err(&pdev->dev, "No usable DMA configuration.\n");
		goto err_out;
	}

	pci_save_state(pdev);
	qdev->reg_base =
	    ioremap_nocache(pci_resource_start(pdev, 1),
			    pci_resource_len(pdev, 1));
	if (!qdev->reg_base) {
		dev_err(&pdev->dev, "Register mapping failed.\n");
		err = -ENOMEM;
		goto err_out;
	}

	qdev->doorbell_area_size = pci_resource_len(pdev, 3);
	qdev->doorbell_area =
	    ioremap_nocache(pci_resource_start(pdev, 3),
			    pci_resource_len(pdev, 3));
	if (!qdev->doorbell_area) {
		dev_err(&pdev->dev, "Doorbell register mapping failed.\n");
		err = -ENOMEM;
		goto err_out;
	}

	err = ql_get_board_info(qdev);
	if (err) {
		dev_err(&pdev->dev, "Register access failed.\n");
		err = -EIO;
		goto err_out;
	}
	qdev->msg_enable = netif_msg_init(debug, default_msg);
	spin_lock_init(&qdev->hw_lock);
	spin_lock_init(&qdev->stats_lock);

	/* make sure the EEPROM is good */
	err = qdev->nic_ops->get_flash(qdev);
	if (err) {
		dev_err(&pdev->dev, "Invalid FLASH.\n");
		goto err_out;
	}

	memcpy(ndev->perm_addr, ndev->dev_addr, ndev->addr_len);

	/* Set up the default ring sizes. */
	qdev->tx_ring_size = NUM_TX_RING_ENTRIES;
	qdev->rx_ring_size = NUM_RX_RING_ENTRIES;

	/* Set up the coalescing parameters. */
	qdev->rx_coalesce_usecs = DFLT_COALESCE_WAIT;
	qdev->tx_coalesce_usecs = DFLT_COALESCE_WAIT;
	qdev->rx_max_coalesced_frames = DFLT_INTER_FRAME_WAIT;
	qdev->tx_max_coalesced_frames = DFLT_INTER_FRAME_WAIT;

	/*
	 * Set up the operating parameters.
	 */
	qdev->rx_csum = 1;
	qdev->workqueue = create_singlethread_workqueue(ndev->name);
	INIT_DELAYED_WORK(&qdev->asic_reset_work, ql_asic_reset_work);
	INIT_DELAYED_WORK(&qdev->mpi_reset_work, ql_mpi_reset_work);
	INIT_DELAYED_WORK(&qdev->mpi_work, ql_mpi_work);
	INIT_DELAYED_WORK(&qdev->mpi_port_cfg_work, ql_mpi_port_cfg_work);
	INIT_DELAYED_WORK(&qdev->mpi_idc_work, ql_mpi_idc_work);
	init_completion(&qdev->ide_completion);

	if (!cards_found) {
		dev_info(&pdev->dev, "%s\n", DRV_STRING);
		dev_info(&pdev->dev, "Driver name: %s, Version: %s.\n",
			 DRV_NAME, DRV_VERSION);
	}
	return 0;
err_out:
	ql_release_all(pdev);
	pci_disable_device(pdev);
	return err;
}


static const struct net_device_ops qlge_netdev_ops = {
	.ndo_open		= qlge_open,
	.ndo_stop		= qlge_close,
	.ndo_start_xmit		= qlge_send,
	.ndo_change_mtu		= qlge_change_mtu,
	.ndo_get_stats		= qlge_get_stats,
	.ndo_set_multicast_list = qlge_set_multicast_list,
	.ndo_set_mac_address	= qlge_set_mac_address,
	.ndo_validate_addr	= eth_validate_addr,
	.ndo_tx_timeout		= qlge_tx_timeout,
	.ndo_vlan_rx_register	= ql_vlan_rx_register,
	.ndo_vlan_rx_add_vid	= ql_vlan_rx_add_vid,
	.ndo_vlan_rx_kill_vid	= ql_vlan_rx_kill_vid,
};

static int __devinit qlge_probe(struct pci_dev *pdev,
				const struct pci_device_id *pci_entry)
{
	struct net_device *ndev = NULL;
	struct ql_adapter *qdev = NULL;
	static int cards_found = 0;
	int err = 0;

	ndev = alloc_etherdev_mq(sizeof(struct ql_adapter),
			min(MAX_CPUS, (int)num_online_cpus()));
	if (!ndev)
		return -ENOMEM;

	err = ql_init_device(pdev, ndev, cards_found);
	if (err < 0) {
		free_netdev(ndev);
		return err;
	}

	qdev = netdev_priv(ndev);
	SET_NETDEV_DEV(ndev, &pdev->dev);
	ndev->features = (0
			  | NETIF_F_IP_CSUM
			  | NETIF_F_SG
			  | NETIF_F_TSO
			  | NETIF_F_TSO6
			  | NETIF_F_TSO_ECN
			  | NETIF_F_HW_VLAN_TX
			  | NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER);
	ndev->features |= NETIF_F_GRO;

	if (test_bit(QL_DMA64, &qdev->flags))
		ndev->features |= NETIF_F_HIGHDMA;

	/*
	 * Set up net_device structure.
	 */
	ndev->tx_queue_len = qdev->tx_ring_size;
	ndev->irq = pdev->irq;

	ndev->netdev_ops = &qlge_netdev_ops;
	SET_ETHTOOL_OPS(ndev, &qlge_ethtool_ops);
	ndev->watchdog_timeo = 10 * HZ;

	err = register_netdev(ndev);
	if (err) {
		dev_err(&pdev->dev, "net device registration failed.\n");
		ql_release_all(pdev);
		pci_disable_device(pdev);
		return err;
	}
	ql_link_off(qdev);
	ql_display_dev_info(ndev);
	cards_found++;
	return 0;
}

static void __devexit qlge_remove(struct pci_dev *pdev)
{
	struct net_device *ndev = pci_get_drvdata(pdev);
	unregister_netdev(ndev);
	ql_release_all(pdev);
	pci_disable_device(pdev);
	free_netdev(ndev);
}

/* Clean up resources without touching hardware. */
static void ql_eeh_close(struct net_device *ndev)
{
	int i;
	struct ql_adapter *qdev = netdev_priv(ndev);

	if (netif_carrier_ok(ndev)) {
		netif_carrier_off(ndev);
		netif_stop_queue(ndev);
	}

	if (test_bit(QL_ADAPTER_UP, &qdev->flags))
		cancel_delayed_work_sync(&qdev->asic_reset_work);
	cancel_delayed_work_sync(&qdev->mpi_reset_work);
	cancel_delayed_work_sync(&qdev->mpi_work);
	cancel_delayed_work_sync(&qdev->mpi_idc_work);
	cancel_delayed_work_sync(&qdev->mpi_port_cfg_work);

	for (i = 0; i < qdev->rss_ring_count; i++)
		netif_napi_del(&qdev->rx_ring[i].napi);

	clear_bit(QL_ADAPTER_UP, &qdev->flags);
	ql_tx_ring_clean(qdev);
	ql_free_rx_buffers(qdev);
	ql_release_adapter_resources(qdev);
}

/*
 * This callback is called by the PCI subsystem whenever
 * a PCI bus error is detected.
 */
static pci_ers_result_t qlge_io_error_detected(struct pci_dev *pdev,
					       enum pci_channel_state state)
{
	struct net_device *ndev = pci_get_drvdata(pdev);

	switch (state) {
	case pci_channel_io_normal:
		return PCI_ERS_RESULT_CAN_RECOVER;
	case pci_channel_io_frozen:
		netif_device_detach(ndev);
		if (netif_running(ndev))
			ql_eeh_close(ndev);
		pci_disable_device(pdev);
		return PCI_ERS_RESULT_NEED_RESET;
	case pci_channel_io_perm_failure:
		dev_err(&pdev->dev,
			"%s: pci_channel_io_perm_failure.\n", __func__);
		return PCI_ERS_RESULT_DISCONNECT;
	}

	/* Request a slot reset. */
	return PCI_ERS_RESULT_NEED_RESET;
}

/*
 * This callback is called after the PCI buss has been reset.
 * Basically, this tries to restart the card from scratch.
 * This is a shortened version of the device probe/discovery code,
 * it resembles the first-half of the () routine.
 */
static pci_ers_result_t qlge_io_slot_reset(struct pci_dev *pdev)
{
	struct net_device *ndev = pci_get_drvdata(pdev);
	struct ql_adapter *qdev = netdev_priv(ndev);

	pdev->error_state = pci_channel_io_normal;

	pci_restore_state(pdev);
	if (pci_enable_device(pdev)) {
		QPRINTK(qdev, IFUP, ERR,
			"Cannot re-enable PCI device after reset.\n");
		return PCI_ERS_RESULT_DISCONNECT;
	}
	pci_set_master(pdev);
	return PCI_ERS_RESULT_RECOVERED;
}

static void qlge_io_resume(struct pci_dev *pdev)
{
	struct net_device *ndev = pci_get_drvdata(pdev);
	struct ql_adapter *qdev = netdev_priv(ndev);
	int err = 0;

	if (ql_adapter_reset(qdev))
		QPRINTK(qdev, DRV, ERR, "reset FAILED!\n");
	if (netif_running(ndev)) {
		err = qlge_open(ndev);
		if (err) {
			QPRINTK(qdev, IFUP, ERR,
				"Device initialization failed after reset.\n");
			return;
		}
	} else {
		QPRINTK(qdev, IFUP, ERR,
			"Device was not running prior to EEH.\n");
	}
	netif_device_attach(ndev);
}

static struct pci_error_handlers qlge_err_handler = {
	.error_detected = qlge_io_error_detected,
	.slot_reset = qlge_io_slot_reset,
	.resume = qlge_io_resume,
};

static int qlge_suspend(struct pci_dev *pdev, pm_message_t state)
{
	struct net_device *ndev = pci_get_drvdata(pdev);
	struct ql_adapter *qdev = netdev_priv(ndev);
	int err;

	netif_device_detach(ndev);

	if (netif_running(ndev)) {
		err = ql_adapter_down(qdev);
		if (!err)
			return err;
	}

	err = pci_save_state(pdev);
	if (err)
		return err;

	pci_disable_device(pdev);

	pci_set_power_state(pdev, pci_choose_state(pdev, state));

	return 0;
}

#ifdef CONFIG_PM
static int qlge_resume(struct pci_dev *pdev)
{
	struct net_device *ndev = pci_get_drvdata(pdev);
	struct ql_adapter *qdev = netdev_priv(ndev);
	int err;

	pci_set_power_state(pdev, PCI_D0);
	pci_restore_state(pdev);
	err = pci_enable_device(pdev);
	if (err) {
		QPRINTK(qdev, IFUP, ERR, "Cannot enable PCI device from suspend\n");
		return err;
	}
	pci_set_master(pdev);

	pci_enable_wake(pdev, PCI_D3hot, 0);
	pci_enable_wake(pdev, PCI_D3cold, 0);

	if (netif_running(ndev)) {
		err = ql_adapter_up(qdev);
		if (err)
			return err;
	}

	netif_device_attach(ndev);

	return 0;
}
#endif /* CONFIG_PM */

static void qlge_shutdown(struct pci_dev *pdev)
{
	qlge_suspend(pdev, PMSG_SUSPEND);
}

static struct pci_driver qlge_driver = {
	.name = DRV_NAME,
	.id_table = qlge_pci_tbl,
	.probe = qlge_probe,
	.remove = __devexit_p(qlge_remove),
#ifdef CONFIG_PM
	.suspend = qlge_suspend,
	.resume = qlge_resume,
#endif
	.shutdown = qlge_shutdown,
	.err_handler = &qlge_err_handler
};

static int __init qlge_init_module(void)
{
	return pci_register_driver(&qlge_driver);
}

static void __exit qlge_exit(void)
{
	pci_unregister_driver(&qlge_driver);
}

module_init(qlge_init_module);
module_exit(qlge_exit);