clock34xx.c

/*
 * OMAP3-specific clock framework functions
 *
 * Copyright (C) 2007 Texas Instruments, Inc.
 * Copyright (C) 2007 Nokia Corporation
 *
 * Written by Paul Walmsley
 *
 * Parts of this code are based on code written by
 * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */
#undef DEBUG

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/list.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/io.h>

#include <asm/arch/clock.h>
#include <asm/arch/sram.h>
#include <asm/div64.h>
#include <asm/bitops.h>

#include "memory.h"
#include "clock.h"
#include "clock34xx.h"
#include "prm.h"
#include "prm-regbits-34xx.h"
#include "cm.h"
#include "cm-regbits-34xx.h"

/* CM_CLKEN_PLL*.EN* bit values */
#define DPLL_LOCKED		0x7

/**
 * omap3_dpll_recalc - recalculate DPLL rate
 * @clk: DPLL struct clk
 *
 * Recalculate and propagate the DPLL rate.
 */
static void omap3_dpll_recalc(struct clk *clk)
{
	clk->rate = omap2_get_dpll_rate(clk);

	propagate_rate(clk);
}

/**
 * omap3_clkoutx2_recalc - recalculate DPLL X2 output virtual clock rate
 * @clk: DPLL output struct clk
 *
 * Using parent clock DPLL data, look up DPLL state.  If locked, set our
 * rate to the dpll_clk * 2; otherwise, just use dpll_clk.
 */
static void omap3_clkoutx2_recalc(struct clk *clk)
{
	const struct dpll_data *dd;
	u32 v;
	struct clk *pclk;

	/* Walk up the parents of clk, looking for a DPLL */
	pclk = clk->parent;
	while (pclk && !pclk->dpll_data)
		pclk = pclk->parent;

	/* clk does not have a DPLL as a parent? */
	WARN_ON(!pclk);

	dd = pclk->dpll_data;

	WARN_ON(!dd->control_reg || !dd->enable_mask);

	v = __raw_readl(dd->control_reg) & dd->enable_mask;
	v >>= __ffs(dd->enable_mask);
	if (v != DPLL_LOCKED)
		clk->rate = clk->parent->rate;
	else
		clk->rate = clk->parent->rate * 2;

	if (clk->flags & RATE_PROPAGATES)
		propagate_rate(clk);
}

/*
 * As it is structured now, this will prevent an OMAP2/3 multiboot
 * kernel from compiling.  This will need further attention.
 */
#if defined(CONFIG_ARCH_OMAP3)

static struct clk_functions omap2_clk_functions = {
	.clk_enable		= omap2_clk_enable,
	.clk_disable		= omap2_clk_disable,
	.clk_round_rate		= omap2_clk_round_rate,
	.clk_set_rate		= omap2_clk_set_rate,
	.clk_set_parent		= omap2_clk_set_parent,
	.clk_disable_unused	= omap2_clk_disable_unused,
};

/*
 * Set clocks for bypass mode for reboot to work.
 */
void omap2_clk_prepare_for_reboot(void)
{
	/* REVISIT: Not ready for 343x */
#if 0
	u32 rate;

	if (vclk == NULL || sclk == NULL)
		return;

	rate = clk_get_rate(sclk);
	clk_set_rate(vclk, rate);
#endif
}

/* REVISIT: Move this init stuff out into clock.c */

/*
 * Switch the MPU rate if specified on cmdline.
 * We cannot do this early until cmdline is parsed.
 */
static int __init omap2_clk_arch_init(void)
{
	if (!mpurate)
		return -EINVAL;

	/* REVISIT: not yet ready for 343x */
#if 0
	if (omap2_select_table_rate(&virt_prcm_set, mpurate))
		printk(KERN_ERR "Could not find matching MPU rate\n");
#endif

	recalculate_root_clocks();

	printk(KERN_INFO "Switched to new clocking rate (Crystal/DPLL3/MPU): "
	       "%ld.%01ld/%ld/%ld MHz\n",
	       (osc_sys_ck.rate / 1000000), (osc_sys_ck.rate / 100000) % 10,
	       (core_ck.rate / 1000000), (dpll1_fck.rate / 1000000)) ;

	return 0;
}
arch_initcall(omap2_clk_arch_init);

int __init omap2_clk_init(void)
{
	/* struct prcm_config *prcm; */
	struct clk **clkp;
	/* u32 clkrate; */
	u32 cpu_clkflg;

	/* REVISIT: Ultimately this will be used for multiboot */
#if 0
	if (cpu_is_omap242x()) {
		cpu_mask = RATE_IN_242X;
		cpu_clkflg = CLOCK_IN_OMAP242X;
		clkp = onchip_24xx_clks;
	} else if (cpu_is_omap2430()) {
		cpu_mask = RATE_IN_243X;
		cpu_clkflg = CLOCK_IN_OMAP243X;
		clkp = onchip_24xx_clks;
	}
#endif
	if (cpu_is_omap34xx()) {
		cpu_mask = RATE_IN_343X;
		cpu_clkflg = CLOCK_IN_OMAP343X;
		clkp = onchip_34xx_clks;

		/*
		 * Update this if there are further clock changes between ES2
		 * and production parts
		 */
		if (is_sil_rev_equal_to(OMAP3430_REV_ES1_0)) {
			/* No 3430ES1-only rates exist, so no RATE_IN_3430ES1 */
			cpu_clkflg |= CLOCK_IN_OMAP3430ES1;
		} else {
			cpu_mask |= RATE_IN_3430ES2;
			cpu_clkflg |= CLOCK_IN_OMAP3430ES2;
		}
	}

	clk_init(&omap2_clk_functions);

	for (clkp = onchip_34xx_clks;
	     clkp < onchip_34xx_clks + ARRAY_SIZE(onchip_34xx_clks);
	     clkp++) {
		if ((*clkp)->flags & cpu_clkflg)
			clk_register(*clkp);
	}

	/* REVISIT: Not yet ready for OMAP3 */
#if 0
	/* Check the MPU rate set by bootloader */
	clkrate = omap2_get_dpll_rate_24xx(&dpll_ck);
	for (prcm = rate_table; prcm->mpu_speed; prcm++) {
		if (!(prcm->flags & cpu_mask))
			continue;
		if (prcm->xtal_speed != sys_ck.rate)
			continue;
		if (prcm->dpll_speed <= clkrate)
			 break;
	}
	curr_prcm_set = prcm;
#endif

	recalculate_root_clocks();

	printk(KERN_INFO "Clocking rate (Crystal/DPLL/ARM core): "
	       "%ld.%01ld/%ld/%ld MHz\n",
	       (osc_sys_ck.rate / 1000000), (osc_sys_ck.rate / 100000) % 10,
	       (core_ck.rate / 1000000), (arm_fck.rate / 1000000));

	/*
	 * Only enable those clocks we will need, let the drivers
	 * enable other clocks as necessary
	 */
	clk_enable_init_clocks();

	/* Avoid sleeping during omap2_clk_prepare_for_reboot() */
	/* REVISIT: not yet ready for 343x */
#if 0
	vclk = clk_get(NULL, "virt_prcm_set");
	sclk = clk_get(NULL, "sys_ck");
#endif
	return 0;
}

#endif