balloon3.c

/*
 *  linux/arch/arm/mach-pxa/balloon3.c
 *
 *  Support for Balloonboard.org Balloon3 board.
 *
 *  Author:	Nick Bane, Wookey, Jonathan McDowell
 *  Created:	June, 2006
 *  Copyright:	Toby Churchill Ltd
 *  Derived from mainstone.c, by Nico Pitre
 *
 *  This program is free software; you can redistribute it and/or modify
 *  it under the terms of the GNU General Public License version 2 as
 *  published by the Free Software Foundation.
 */

#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/sysdev.h>
#include <linux/interrupt.h>
#include <linux/sched.h>
#include <linux/bitops.h>
#include <linux/fb.h>
#include <linux/gpio.h>
#include <linux/ioport.h>
#include <linux/ucb1400.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/types.h>
#include <linux/i2c/pcf857x.h>

#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/sizes.h>

#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>

#include <mach/pxa27x.h>
#include <mach/balloon3.h>
#include <mach/audio.h>
#include <mach/pxafb.h>
#include <mach/mmc.h>
#include <mach/udc.h>
#include <mach/pxa27x-udc.h>
#include <mach/irda.h>
#include <mach/ohci.h>

#include <plat/i2c.h>

#include "generic.h"
#include "devices.h"

/******************************************************************************
 * Pin configuration
 ******************************************************************************/
static unsigned long balloon3_pin_config[] __initdata = {
	/* Select BTUART 'COM1/ttyS0' as IO option for pins 42/43/44/45 */
	GPIO42_BTUART_RXD,
	GPIO43_BTUART_TXD,
	GPIO44_BTUART_CTS,
	GPIO45_BTUART_RTS,

	/* Reset, configured as GPIO wakeup source */
	GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,

	/* LEDs */
	GPIO9_GPIO,	/* NAND activity LED */
	GPIO10_GPIO,	/* Heartbeat LED */

	/* AC97 */
	GPIO28_AC97_BITCLK,
	GPIO29_AC97_SDATA_IN_0,
	GPIO30_AC97_SDATA_OUT,
	GPIO31_AC97_SYNC,
	GPIO113_AC97_nRESET,
	GPIO95_GPIO,

	/* MMC */
	GPIO32_MMC_CLK,
	GPIO92_MMC_DAT_0,
	GPIO109_MMC_DAT_1,
	GPIO110_MMC_DAT_2,
	GPIO111_MMC_DAT_3,
	GPIO112_MMC_CMD,

	/* USB Host */
	GPIO88_USBH1_PWR,
	GPIO89_USBH1_PEN,

	/* PC Card */
	GPIO48_nPOE,
	GPIO49_nPWE,
	GPIO50_nPIOR,
	GPIO51_nPIOW,
	GPIO85_nPCE_1,
	GPIO54_nPCE_2,
	GPIO79_PSKTSEL,
	GPIO55_nPREG,
	GPIO56_nPWAIT,
	GPIO57_nIOIS16,
};

/******************************************************************************
 * Compatibility: Parameter parsing
 ******************************************************************************/
static unsigned long balloon3_irq_enabled;

static unsigned long balloon3_features_present =
		(1 << BALLOON3_FEATURE_OHCI) | (1 << BALLOON3_FEATURE_CF) |
		(1 << BALLOON3_FEATURE_AUDIO) |
		(1 << BALLOON3_FEATURE_TOPPOLY);

int balloon3_has(enum balloon3_features feature)
{
	return (balloon3_features_present & (1 << feature)) ? 1 : 0;
}
EXPORT_SYMBOL_GPL(balloon3_has);

int __init parse_balloon3_features(char *arg)
{
	if (!arg)
		return 0;

	return strict_strtoul(arg, 0, &balloon3_features_present);
}
early_param("balloon3_features", parse_balloon3_features);

/******************************************************************************
 * NOR Flash
 ******************************************************************************/
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
static struct mtd_partition balloon3_nor_partitions[] = {
	{
		.name		= "Flash",
		.offset		= 0x00000000,
		.size		= MTDPART_SIZ_FULL,
	}
};

static struct physmap_flash_data balloon3_flash_data[] = {
	{
		.width		= 2,	/* bankwidth in bytes */
		.parts		= balloon3_nor_partitions,
		.nr_parts	= ARRAY_SIZE(balloon3_nor_partitions)
	}
};

static struct resource balloon3_flash_resource = {
	.start	= PXA_CS0_PHYS,
	.end	= PXA_CS0_PHYS + SZ_64M - 1,
	.flags	= IORESOURCE_MEM,
};

static struct platform_device balloon3_flash = {
	.name		= "physmap-flash",
	.id		= 0,
	.resource	= &balloon3_flash_resource,
	.num_resources	= 1,
	.dev 		= {
		.platform_data = balloon3_flash_data,
	},
};
static void __init balloon3_nor_init(void)
{
	platform_device_register(&balloon3_flash);
}
#else
static inline void balloon3_nor_init(void) {}
#endif

/******************************************************************************
 * Audio and Touchscreen
 ******************************************************************************/
#if	defined(CONFIG_TOUCHSCREEN_UCB1400) || \
	defined(CONFIG_TOUCHSCREEN_UCB1400_MODULE)
static struct ucb1400_pdata vpac270_ucb1400_pdata = {
	.irq		= IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ),
};


static struct platform_device balloon3_ucb1400_device = {
	.name		= "ucb1400_core",
	.id		= -1,
	.dev		= {
		.platform_data = &vpac270_ucb1400_pdata,
	},
};

static void __init balloon3_ts_init(void)
{
	if (!balloon3_has(BALLOON3_FEATURE_AUDIO))
		return;

	pxa_set_ac97_info(NULL);
	platform_device_register(&balloon3_ucb1400_device);
}
#else
static inline void balloon3_ts_init(void) {}
#endif

/******************************************************************************
 * Framebuffer
 ******************************************************************************/
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
static struct pxafb_mode_info balloon3_lcd_modes[] = {
	{
		.pixclock		= 38000,
		.xres			= 480,
		.yres			= 640,
		.bpp			= 16,
		.hsync_len		= 8,
		.left_margin		= 8,
		.right_margin		= 8,
		.vsync_len		= 2,
		.upper_margin		= 4,
		.lower_margin		= 5,
		.sync			= 0,
	},
};

static struct pxafb_mach_info balloon3_lcd_screen = {
	.modes			= balloon3_lcd_modes,
	.num_modes		= ARRAY_SIZE(balloon3_lcd_modes),
	.lcd_conn		= LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
};

static void balloon3_backlight_power(int on)
{
	gpio_set_value(BALLOON3_GPIO_RUN_BACKLIGHT, on);
}

static void __init balloon3_lcd_init(void)
{
	int ret;

	if (!balloon3_has(BALLOON3_FEATURE_TOPPOLY))
		return;

	ret = gpio_request(BALLOON3_GPIO_RUN_BACKLIGHT, "BKL-ON");
	if (ret) {
		pr_err("Requesting BKL-ON GPIO failed!\n");
		goto err;
	}

	ret = gpio_direction_output(BALLOON3_GPIO_RUN_BACKLIGHT, 1);
	if (ret) {
		pr_err("Setting BKL-ON GPIO direction failed!\n");
		goto err2;
	}

	balloon3_lcd_screen.pxafb_backlight_power = balloon3_backlight_power;
	set_pxa_fb_info(&balloon3_lcd_screen);
	return;

err2:
	gpio_free(BALLOON3_GPIO_RUN_BACKLIGHT);
err:
	return;
}
#else
static inline void balloon3_lcd_init(void) {}
#endif

/******************************************************************************
 * SD/MMC card controller
 ******************************************************************************/
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
static struct pxamci_platform_data balloon3_mci_platform_data = {
	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
	.gpio_card_detect	= -1,
	.gpio_card_ro		= -1,
	.gpio_power		= -1,
	.detect_delay_ms	= 200,
};

static void __init balloon3_mmc_init(void)
{
	pxa_set_mci_info(&balloon3_mci_platform_data);
}
#else
static inline void balloon3_mmc_init(void) {}
#endif

/******************************************************************************
 * USB Gadget
 ******************************************************************************/
#if defined(CONFIG_USB_GADGET_PXA27X)||defined(CONFIG_USB_GADGET_PXA27X_MODULE)
static void balloon3_udc_command(int cmd)
{
	if (cmd == PXA2XX_UDC_CMD_CONNECT)
		UP2OCR |= UP2OCR_DPPUE | UP2OCR_DPPUBE;
	else if (cmd == PXA2XX_UDC_CMD_DISCONNECT)
		UP2OCR &= ~UP2OCR_DPPUE;
}

static int balloon3_udc_is_connected(void)
{
	return 1;
}

static struct pxa2xx_udc_mach_info balloon3_udc_info __initdata = {
	.udc_command		= balloon3_udc_command,
	.udc_is_connected	= balloon3_udc_is_connected,
	.gpio_pullup		= -1,
};

static void __init balloon3_udc_init(void)
{
	pxa_set_udc_info(&balloon3_udc_info);
	platform_device_register(&balloon3_gpio_vbus);
}
#else
static inline void balloon3_udc_init(void) {}
#endif

/******************************************************************************
 * IrDA
 ******************************************************************************/
#if defined(CONFIG_IRDA) || defined(CONFIG_IRDA_MODULE)
static struct pxaficp_platform_data balloon3_ficp_platform_data = {
	.transceiver_cap	= IR_FIRMODE | IR_SIRMODE | IR_OFF,
};

static void __init balloon3_irda_init(void)
{
	pxa_set_ficp_info(&balloon3_ficp_platform_data);
}
#else
static inline void balloon3_irda_init(void) {}
#endif

/******************************************************************************
 * USB Host
 ******************************************************************************/
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
static struct pxaohci_platform_data balloon3_ohci_info = {
	.port_mode	= PMM_PERPORT_MODE,
	.flags		= ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW,
};

static void __init balloon3_uhc_init(void)
{
	if (!balloon3_has(BALLOON3_FEATURE_OHCI))
		return;
	pxa_set_ohci_info(&balloon3_ohci_info);
}
#else
static inline void balloon3_uhc_init(void) {}
#endif

/******************************************************************************
 * LEDs
 ******************************************************************************/
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
struct gpio_led balloon3_gpio_leds[] = {
	{
		.name			= "balloon3:green:idle",
		.default_trigger	= "heartbeat",
		.gpio			= BALLOON3_GPIO_LED_IDLE,
		.active_low		= 1,
	}, {
		.name			= "balloon3:green:nand",
		.default_trigger	= "nand-disk",
		.gpio			= BALLOON3_GPIO_LED_NAND,
		.active_low		= 1,
	},
};

static struct gpio_led_platform_data balloon3_gpio_led_info = {
	.leds		= balloon3_gpio_leds,
	.num_leds	= ARRAY_SIZE(balloon3_gpio_leds),
};

static struct platform_device balloon3_leds = {
	.name	= "leds-gpio",
	.id	= 0,
	.dev	= {
		.platform_data	= &balloon3_gpio_led_info,
	}
};

struct gpio_led balloon3_pcf_gpio_leds[] = {
	{
		.name			= "balloon3:green:led0",
		.gpio			= BALLOON3_PCF_GPIO_LED0,
		.active_low		= 1,
	}, {
		.name			= "balloon3:green:led1",
		.gpio			= BALLOON3_PCF_GPIO_LED1,
		.active_low		= 1,
	}, {
		.name			= "balloon3:orange:led2",
		.gpio			= BALLOON3_PCF_GPIO_LED2,
		.active_low		= 1,
	}, {
		.name			= "balloon3:orange:led3",
		.gpio			= BALLOON3_PCF_GPIO_LED3,
		.active_low		= 1,
	}, {
		.name			= "balloon3:orange:led4",
		.gpio			= BALLOON3_PCF_GPIO_LED4,
		.active_low		= 1,
	}, {
		.name			= "balloon3:orange:led5",
		.gpio			= BALLOON3_PCF_GPIO_LED5,
		.active_low		= 1,
	}, {
		.name			= "balloon3:red:led6",
		.gpio			= BALLOON3_PCF_GPIO_LED6,
		.active_low		= 1,
	}, {
		.name			= "balloon3:red:led7",
		.gpio			= BALLOON3_PCF_GPIO_LED7,
		.active_low		= 1,
	},
};

static struct gpio_led_platform_data balloon3_pcf_gpio_led_info = {
	.leds		= balloon3_pcf_gpio_leds,
	.num_leds	= ARRAY_SIZE(balloon3_pcf_gpio_leds),
};

static struct platform_device balloon3_pcf_leds = {
	.name	= "leds-gpio",
	.id	= 1,
	.dev	= {
		.platform_data	= &balloon3_pcf_gpio_led_info,
	}
};

static void __init balloon3_leds_init(void)
{
	platform_device_register(&balloon3_leds);
	platform_device_register(&balloon3_pcf_leds);
}
#else
static inline void balloon3_leds_init(void) {}
#endif

/******************************************************************************
 * FPGA IRQ
 ******************************************************************************/
static void balloon3_mask_irq(unsigned int irq)
{
	int balloon3_irq = (irq - BALLOON3_IRQ(0));
	balloon3_irq_enabled &= ~(1 << balloon3_irq);
	__raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
}

static void balloon3_unmask_irq(unsigned int irq)
{
	int balloon3_irq = (irq - BALLOON3_IRQ(0));
	balloon3_irq_enabled |= (1 << balloon3_irq);
	__raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
}

static struct irq_chip balloon3_irq_chip = {
	.name		= "FPGA",
	.ack		= balloon3_mask_irq,
	.mask		= balloon3_mask_irq,
	.unmask		= balloon3_unmask_irq,
};

static void balloon3_irq_handler(unsigned int irq, struct irq_desc *desc)
{
	unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
					balloon3_irq_enabled;
	do {
		/* clear useless edge notification */
		if (desc->chip->ack)
			desc->chip->ack(BALLOON3_AUX_NIRQ);
		while (pending) {
			irq = BALLOON3_IRQ(0) + __ffs(pending);
			generic_handle_irq(irq);
			pending &= pending - 1;
		}
		pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
				balloon3_irq_enabled;
	} while (pending);
}

static void __init balloon3_init_irq(void)
{
	int irq;

	pxa27x_init_irq();
	/* setup extra Balloon3 irqs */
	for (irq = BALLOON3_IRQ(0); irq <= BALLOON3_IRQ(7); irq++) {
		set_irq_chip(irq, &balloon3_irq_chip);
		set_irq_handler(irq, handle_level_irq);
		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
	}

	set_irq_chained_handler(BALLOON3_AUX_NIRQ, balloon3_irq_handler);
	set_irq_type(BALLOON3_AUX_NIRQ, IRQ_TYPE_EDGE_FALLING);

	pr_debug("%s: chained handler installed - irq %d automatically "
		"enabled\n", __func__, BALLOON3_AUX_NIRQ);
}

/******************************************************************************
 * GPIO expander
 ******************************************************************************/
#if defined(CONFIG_GPIO_PCF857X) || defined(CONFIG_GPIO_PCF857X_MODULE)
static struct pcf857x_platform_data balloon3_pcf857x_pdata = {
	.gpio_base	= BALLOON3_PCF_GPIO_BASE,
	.n_latch	= 0,
	.setup		= NULL,
	.teardown	= NULL,
	.context	= NULL,
};

static struct i2c_board_info __initdata balloon3_i2c_devs[] = {
	{
		I2C_BOARD_INFO("pcf8574a", 0x38),
		.platform_data	= &balloon3_pcf857x_pdata,
	},
};

static void __init balloon3_i2c_init(void)
{
	pxa_set_i2c_info(NULL);
	i2c_register_board_info(0, ARRAY_AND_SIZE(balloon3_i2c_devs));
}
#else
static inline void balloon3_i2c_init(void) {}
#endif

/******************************************************************************
 * Machine init
 ******************************************************************************/
static void __init balloon3_init(void)
{
	ARB_CNTRL = ARB_CORE_PARK | 0x234;

	pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_pin_config));

	pxa_set_ffuart_info(NULL);
	pxa_set_btuart_info(NULL);
	pxa_set_stuart_info(NULL);

	balloon3_i2c_init();
	balloon3_irda_init();
	balloon3_lcd_init();
	balloon3_leds_init();
	balloon3_mmc_init();
	balloon3_nor_init();
	balloon3_ts_init();
	balloon3_udc_init();
	balloon3_uhc_init();
}

static struct map_desc balloon3_io_desc[] __initdata = {
	{	/* CPLD/FPGA */
		.virtual	=  BALLOON3_FPGA_VIRT,
		.pfn		= __phys_to_pfn(BALLOON3_FPGA_PHYS),
		.length		= BALLOON3_FPGA_LENGTH,
		.type		= MT_DEVICE,
	},
};

static void __init balloon3_map_io(void)
{
	pxa_map_io();
	iotable_init(balloon3_io_desc, ARRAY_SIZE(balloon3_io_desc));
}

MACHINE_START(BALLOON3, "Balloon3")
	/* Maintainer: Nick Bane. */
	.phys_io	= 0x40000000,
	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
	.map_io		= balloon3_map_io,
	.init_irq	= balloon3_init_irq,
	.timer		= &pxa_timer,
	.init_machine	= balloon3_init,
	.boot_params	= PHYS_OFFSET + 0x100,
MACHINE_END