rv.h

#ifndef __AM33XX_H__
#define __AM33XX_H__

#define __REG32(x)  (*((volatile unsigned int *)(x)))
#define __REG16(x)  (*((volatile unsigned short *)(x)))

/*
 * Peripheral addresses
 */
#define REALVIEW_UART0_BASE         0x10009000  /* UART 0 */
#define REALVIEW_UART1_BASE         0x1000A000  /* UART 1 */
#define REALVIEW_UART2_BASE         0x1000B000  /* UART 2 */
#define REALVIEW_UART3_BASE         0x1000C000  /* UART 3 */
#define REALVIEW_SSP_BASE           0x1000D000  /* Synchronous Serial Port */
#define REALVIEW_WATCHDOG0_BASE     0x1000F000  /* Watchdog 0 */
#define REALVIEW_WATCHDOG_BASE      0x10010000  /* watchdog interface */
#define REALVIEW_TIMER0_1_BASE      0x10011000  /* Timer 0 and 1 */
#define REALVIEW_TIMER2_3_BASE      0x10012000  /* Timer 2 and 3 */
#define REALVIEW_GPIO0_BASE         0x10013000  /* GPIO port 0 */
#define REALVIEW_RTC_BASE           0x10017000  /* Real Time Clock */
#define REALVIEW_TIMER4_5_BASE      0x10018000  /* Timer 4/5 */
#define REALVIEW_TIMER6_7_BASE      0x10019000  /* Timer 6/7 */
#define REALVIEW_SCTL_BASE          0x10001000  /* System Controller */
#define REALVIEW_CLCD_BASE          0x10020000  /* CLCD */
#define REALVIEW_ONB_SRAM_BASE      0x10060000  /* On-board SRAM */
#define REALVIEW_DMC_BASE           0x100E0000  /* DMC configuration */
#define REALVIEW_SMC_BASE           0x100E1000  /* SMC configuration */
#define REALVIEW_CAN_BASE           0x100E2000  /* CAN bus */
#define REALVIEW_GIC_CPU_BASE       (0x00A00000+0x2000)  /* Generic interrupt controller CPU interface */
#define REALVIEW_FLASH0_BASE        0x40000000
#define REALVIEW_FLASH0_SIZE        SZ_64M
#define REALVIEW_FLASH1_BASE        0x44000000
#define REALVIEW_FLASH1_SIZE        SZ_64M

#define VEXPRESS_SRAM_BASE          0x48000000

#define REALVIEW_ETH_BASE           0x4E000000  /* Ethernet */
#define VEXPRESS_ETH_BASE           0x4E000000  /* Ethernet */

#define REALVIEW_USB_BASE           0x4F000000  /* USB */
#define REALVIEW_GIC_DIST_BASE      (0x00A00000+0x1000)  /* Generic interrupt controller distributor */
#define REALVIEW_LT_BASE            0xC0000000  /* Logic Tile expansion */
#define REALVIEW_SDRAM6_BASE        0x70000000  /* SDRAM bank 6 256MB */
#define REALVIEW_SDRAM7_BASE        0x80000000  /* SDRAM bank 7 256MB */

#define REALVIEW_SYS_PLD_CTRL1      0x74

/*
 * PCI regions
 */
#define REALVIEW_PCI_BASE           0x90040000  /* PCI-X Unit base */
#define REALVIEW_PCI_IO_BASE        0x90050000  /* IO Region on AHB */
#define REALVIEW_PCI_MEM_BASE       0xA0000000  /* MEM Region on AHB */

#define REALVIEW_PCI_BASE_SIZE      0x10000     /* 16 Kb */
#define REALVIEW_PCI_IO_SIZE        0x1000      /* 4 Kb */
#define REALVIEW_PCI_MEM_SIZE       0x20000000  /* 512 MB */

/*
 * Memory definitions
 */
#define REALVIEW_BOOT_ROM_LO          0x30000000    /* DoC Base (64Mb)... */
#define REALVIEW_BOOT_ROM_HI          0x30000000
#define REALVIEW_BOOT_ROM_BASE        REALVIEW_BOOT_ROM_HI  /*  Normal position */
#define REALVIEW_BOOT_ROM_SIZE        SZ_64M

#define REALVIEW_SSRAM_BASE /* REALVIEW_SSMC_BASE ? */
#define REALVIEW_SSRAM_SIZE           SZ_2M

/*
 *  SDRAM
 */
#define REALVIEW_SDRAM_BASE           0x00000000

/*
 *  Logic expansion modules
 *
 */
#define IRQ_PBA8_GIC_START          32

/*
 * PB-A8 on-board gic irq sources
 */
#define IRQ_PBA8_WATCHDOG   (IRQ_PBA8_GIC_START + 0)    /* Watchdog timer */
#define IRQ_PBA8_SOFT       (IRQ_PBA8_GIC_START + 1)    /* Software interrupt */
#define IRQ_PBA8_TIMER0_1   (IRQ_PBA8_GIC_START + 2)    /* Timer 0/1 (default timer) */
#define IRQ_PBA8_TIMER2_3   (IRQ_PBA8_GIC_START + 3)    /* Timer 2/3 */
#define IRQ_PBA8_RTC        (IRQ_PBA8_GIC_START + 4)    /* Timer 2/3 */
#define IRQ_VEXPRESS_A9_RTC (IRQ_PBA8_GIC_START + 4)

#define IRQ_PBA8_UART0      (IRQ_PBA8_GIC_START + 5)    /* UART 0 on development chip */
#define IRQ_PBA8_UART1      (IRQ_PBA8_GIC_START + 6)    /* UART 1 on development chip */
#define IRQ_PBA8_UART2      (IRQ_PBA8_GIC_START + 7)    /* UART 2 on development chip */
#define IRQ_PBA8_UART3      (IRQ_PBA8_GIC_START + 8)    /* UART 3 on development chip */

#define IRQ_VEXPRESS_A9_KBD     (IRQ_PBA8_GIC_START + 12)
#define IRQ_VEXPRESS_A9_MOUSE   (IRQ_PBA8_GIC_START + 13)
#define IRQ_VEXPRESS_A9_CLCD    (IRQ_PBA8_GIC_START + 14)
#define IRQ_VEXPRESS_A9_ETH     (IRQ_PBA8_GIC_START + 15)

/* 9 reserved */
#define IRQ_PBA8_SSP        (IRQ_PBA8_GIC_START + 11)   /* Synchronous Serial Port */
#define IRQ_PBA8_SCI        (IRQ_PBA8_GIC_START + 16)   /* Smart Card Interface */
#define IRQ_PBA8_MMCI0A     (IRQ_PBA8_GIC_START + 17)   /* Multimedia Card 0A */
#define IRQ_PBA8_MMCI0B     (IRQ_PBA8_GIC_START + 18)   /* Multimedia Card 0B */
#define IRQ_PBA8_AACI       (IRQ_PBA8_GIC_START + 19)   /* Audio Codec */
#define IRQ_PBA8_KMI0       (IRQ_PBA8_GIC_START + 20)   /* Keyboard/Mouse port 0 */
#define IRQ_PBA8_KMI1       (IRQ_PBA8_GIC_START + 21)   /* Keyboard/Mouse port 1 */
#define IRQ_PBA8_CHARLCD    (IRQ_PBA8_GIC_START + 22)   /* Character LCD */
#define IRQ_PBA8_CLCD       (IRQ_PBA8_GIC_START + 23)   /* CLCD controller */
#define IRQ_PBA8_DMAC       (IRQ_PBA8_GIC_START + 24)   /* DMA controller */
#define IRQ_PBA8_PWRFAIL    (IRQ_PBA8_GIC_START + 25)   /* Power failure */
#define IRQ_PBA8_PISMO      (IRQ_PBA8_GIC_START + 26)   /* PISMO interface */
#define IRQ_PBA8_DoC        (IRQ_PBA8_GIC_START + 27)   /* Disk on Chip memory controller */
#define IRQ_PBA8_ETH        (IRQ_PBA8_GIC_START + 28)   /* Ethernet controller */
#define IRQ_PBA8_USB        (IRQ_PBA8_GIC_START + 29)   /* USB controller */
#define IRQ_PBA8_TSPEN      (IRQ_PBA8_GIC_START + 30)   /* Touchscreen pen */
#define IRQ_PBA8_TSKPAD     (IRQ_PBA8_GIC_START + 31)   /* Touchscreen keypad */

#define IRQ_PBA8_PMU        (IRQ_PBA8_GIC_START + 47)   /* Cortex-A8 PMU */

/* ... */
#define IRQ_PBA8_PCI0       (IRQ_PBA8_GIC_START + 50)
#define IRQ_PBA8_PCI1       (IRQ_PBA8_GIC_START + 51)
#define IRQ_PBA8_PCI2       (IRQ_PBA8_GIC_START + 52)
#define IRQ_PBA8_PCI3       (IRQ_PBA8_GIC_START + 53)

#define IRQ_PBA8_SMC        -1
#define IRQ_PBA8_SCTL       -1

#define NR_GIC_PBA8     1

/*
 * Only define NR_IRQS if less than NR_IRQS_PBA8
 */
#define NR_IRQS_PBA8        (IRQ_PBA8_GIC_START + 64)

/* ------------------------------------------------------------------------
 *  RealView Registers
 * ------------------------------------------------------------------------
 *
 */
#define REALVIEW_SYS_ID_OFFSET               0x00
#define REALVIEW_SYS_SW_OFFSET               0x04
#define REALVIEW_SYS_LED_OFFSET              0x08
#define REALVIEW_SYS_OSC0_OFFSET             0x0C

#define REALVIEW_SYS_OSC1_OFFSET             0x10
#define REALVIEW_SYS_OSC2_OFFSET             0x14
#define REALVIEW_SYS_OSC3_OFFSET             0x18
#define REALVIEW_SYS_OSC4_OFFSET             0x1C   /* OSC1 for RealView/AB */

#define REALVIEW_SYS_LOCK_OFFSET             0x20
#define REALVIEW_SYS_100HZ_OFFSET            0x24
#define REALVIEW_SYS_CFGDATA1_OFFSET         0x28
#define REALVIEW_SYS_CFGDATA2_OFFSET         0x2C
#define REALVIEW_SYS_FLAGS_OFFSET            0x30
#define REALVIEW_SYS_FLAGSSET_OFFSET         0x30
#define REALVIEW_SYS_FLAGSCLR_OFFSET         0x34
#define REALVIEW_SYS_NVFLAGS_OFFSET          0x38
#define REALVIEW_SYS_NVFLAGSSET_OFFSET       0x38
#define REALVIEW_SYS_NVFLAGSCLR_OFFSET       0x3C
#define REALVIEW_SYS_RESETCTL_OFFSET         0x40
#define REALVIEW_SYS_PCICTL_OFFSET           0x44
#define REALVIEW_SYS_MCI_OFFSET              0x48
#define REALVIEW_SYS_FLASH_OFFSET            0x4C
#define REALVIEW_SYS_CLCD_OFFSET             0x50
#define REALVIEW_SYS_CLCDSER_OFFSET          0x54
#define REALVIEW_SYS_BOOTCS_OFFSET           0x58
#define REALVIEW_SYS_24MHz_OFFSET            0x5C
#define REALVIEW_SYS_MISC_OFFSET             0x60
#define REALVIEW_SYS_IOSEL_OFFSET            0x70
#define REALVIEW_SYS_PROCID_OFFSET           0x84
#define REALVIEW_SYS_TEST_OSC0_OFFSET        0xC0
#define REALVIEW_SYS_TEST_OSC1_OFFSET        0xC4
#define REALVIEW_SYS_TEST_OSC2_OFFSET        0xC8
#define REALVIEW_SYS_TEST_OSC3_OFFSET        0xCC
#define REALVIEW_SYS_TEST_OSC4_OFFSET        0xD0

#define REALVIEW_SYS_BASE                    0x10000000
#define REALVIEW_SYS_ID                      (REALVIEW_SYS_BASE + REALVIEW_SYS_ID_OFFSET)
#define REALVIEW_SYS_SW                      (REALVIEW_SYS_BASE + REALVIEW_SYS_SW_OFFSET)
#define REALVIEW_SYS_LED                     (REALVIEW_SYS_BASE + REALVIEW_SYS_LED_OFFSET)
#define REALVIEW_SYS_OSC0                    (REALVIEW_SYS_BASE + REALVIEW_SYS_OSC0_OFFSET)
#define REALVIEW_SYS_OSC1                    (REALVIEW_SYS_BASE + REALVIEW_SYS_OSC1_OFFSET)

#define REALVIEW_SYS_LOCK                    (REALVIEW_SYS_BASE + REALVIEW_SYS_LOCK_OFFSET)
#define REALVIEW_SYS_100HZ                   (REALVIEW_SYS_BASE + REALVIEW_SYS_100HZ_OFFSET)
#define REALVIEW_SYS_CFGDATA1                (REALVIEW_SYS_BASE + REALVIEW_SYS_CFGDATA1_OFFSET)
#define REALVIEW_SYS_CFGDATA2                (REALVIEW_SYS_BASE + REALVIEW_SYS_CFGDATA2_OFFSET)
#define REALVIEW_SYS_FLAGS                   (REALVIEW_SYS_BASE + REALVIEW_SYS_FLAGS_OFFSET)
#define REALVIEW_SYS_FLAGSSET                (REALVIEW_SYS_BASE + REALVIEW_SYS_FLAGSSET_OFFSET)
#define REALVIEW_SYS_FLAGSCLR                (REALVIEW_SYS_BASE + REALVIEW_SYS_FLAGSCLR_OFFSET)
#define REALVIEW_SYS_NVFLAGS                 (REALVIEW_SYS_BASE + REALVIEW_SYS_NVFLAGS_OFFSET)
#define REALVIEW_SYS_NVFLAGSSET              (REALVIEW_SYS_BASE + REALVIEW_SYS_NVFLAGSSET_OFFSET)
#define REALVIEW_SYS_NVFLAGSCLR              (REALVIEW_SYS_BASE + REALVIEW_SYS_NVFLAGSCLR_OFFSET)
#define REALVIEW_SYS_RESETCTL                (REALVIEW_SYS_BASE + REALVIEW_SYS_RESETCTL_OFFSET)
#define REALVIEW_SYS_PCICTL                  (REALVIEW_SYS_BASE + REALVIEW_SYS_PCICTL_OFFSET)
#define REALVIEW_SYS_MCI                     (REALVIEW_SYS_BASE + REALVIEW_SYS_MCI_OFFSET)
#define REALVIEW_SYS_FLASH                   (REALVIEW_SYS_BASE + REALVIEW_SYS_FLASH_OFFSET)
#define REALVIEW_SYS_CLCD                    (REALVIEW_SYS_BASE + REALVIEW_SYS_CLCD_OFFSET)
#define REALVIEW_SYS_CLCDSER                 (REALVIEW_SYS_BASE + REALVIEW_SYS_CLCDSER_OFFSET)
#define REALVIEW_SYS_BOOTCS                  (REALVIEW_SYS_BASE + REALVIEW_SYS_BOOTCS_OFFSET)
#define REALVIEW_SYS_24MHz                   (REALVIEW_SYS_BASE + REALVIEW_SYS_24MHz_OFFSET)
#define REALVIEW_SYS_MISC                    (REALVIEW_SYS_BASE + REALVIEW_SYS_MISC_OFFSET)
#define REALVIEW_SYS_IOSEL                   (REALVIEW_SYS_BASE + REALVIEW_SYS_IOSEL_OFFSET)
#define REALVIEW_SYS_PROCID                  (REALVIEW_SYS_BASE + REALVIEW_SYS_PROCID_OFFSET)
#define REALVIEW_SYS_TEST_OSC0               (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC0_OFFSET)
#define REALVIEW_SYS_TEST_OSC1               (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC1_OFFSET)
#define REALVIEW_SYS_TEST_OSC2               (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC2_OFFSET)
#define REALVIEW_SYS_TEST_OSC3               (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC3_OFFSET)
#define REALVIEW_SYS_TEST_OSC4               (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC4_OFFSET)

#define REALVIEW_SYS_CTRL_LED         (1 << 0)

/* ------------------------------------------------------------------------
 *  RealView control registers
 * ------------------------------------------------------------------------
 */

/*
 * REALVIEW_IDFIELD
 *
 * 31:24 = manufacturer (0x41 = ARM)
 * 23:16 = architecture (0x08 = AHB system bus, ASB processor bus)
 * 15:12 = FPGA (0x3 = XVC600 or XVC600E)
 * 11:4  = build value
 * 3:0   = revision number (0x1 = rev B (AHB))
 */

/*
 * REALVIEW_SYS_LOCK
 *     control access to SYS_OSCx, SYS_CFGDATAx, SYS_RESETCTL,
 *     SYS_CLD, SYS_BOOTCS
 */
#define REALVIEW_SYS_LOCK_LOCKED    (1 << 16)
#define REALVIEW_SYS_LOCKVAL        0xA05F
#define REALVIEW_SYS_LOCKVAL_MASK   0xFFFF  /* write 0xA05F to enable write access */

/*
 * REALVIEW_SYS_FLASH
 */
#define REALVIEW_FLASHPROG_FLVPPEN  (1 << 0)    /* Enable writing to flash */

/*
 * REALVIEW_INTREG
 *     - used to acknowledge and control MMCI and UART interrupts
 */
#define REALVIEW_INTREG_WPROT        0x00   /* MMC protection status (no interrupt generated) */
#define REALVIEW_INTREG_RI0          0x01   /* Ring indicator UART0 is asserted,              */
#define REALVIEW_INTREG_CARDIN       0x08   /* MMCI card in detect                            */
/* write 1 to acknowledge and clear               */
#define REALVIEW_INTREG_RI1          0x02   /* Ring indicator UART1 is asserted,              */
#define REALVIEW_INTREG_CARDINSERT   0x03   /* Signal insertion of MMC card                   */

/*
 *  LED settings, bits [7:0]
 */
#define REALVIEW_SYS_LED0             (1 << 0)
#define REALVIEW_SYS_LED1             (1 << 1)
#define REALVIEW_SYS_LED2             (1 << 2)
#define REALVIEW_SYS_LED3             (1 << 3)
#define REALVIEW_SYS_LED4             (1 << 4)
#define REALVIEW_SYS_LED5             (1 << 5)
#define REALVIEW_SYS_LED6             (1 << 6)
#define REALVIEW_SYS_LED7             (1 << 7)

#define ALL_LEDS                  0xFF

#define LED_BANK                  REALVIEW_SYS_LED

/*
 * Control registers
 */
#define REALVIEW_IDFIELD_OFFSET 0x0 /* RealView build information */
#define REALVIEW_FLASHPROG_OFFSET   0x4 /* Flash devices */
#define REALVIEW_INTREG_OFFSET      0x8 /* Interrupt control */
#define REALVIEW_DECODE_OFFSET      0xC /* Fitted logic modules */

/*
 *  Clean base - dummy
 *
 */
#define CLEAN_BASE                      REALVIEW_BOOT_ROM_HI

/*
 * System controller bit assignment
 */
#define REALVIEW_REFCLK 0
#define REALVIEW_TIMCLK 1

#define REALVIEW_TIMER1_EnSel   15
#define REALVIEW_TIMER2_EnSel   17
#define REALVIEW_TIMER3_EnSel   19
#define REALVIEW_TIMER4_EnSel   21

struct rt_hw_register
{
    unsigned long r0;
    unsigned long r1;
    unsigned long r2;
    unsigned long r3;
    unsigned long r4;
    unsigned long r5;
    unsigned long r6;
    unsigned long r7;
    unsigned long r8;
    unsigned long r9;
    unsigned long r10;
    unsigned long fp;
    unsigned long ip;
    unsigned long sp;
    unsigned long lr;
    unsigned long pc;
    unsigned long cpsr;
    unsigned long ORIG_r0;
};

#include <rtdef.h>
#include <armv7.h>

/* Interrupt Control Interface */
#define ARM_GIC_CPU_BASE    0x1E000000

/* number of interrupts on board */
#define ARM_GIC_NR_IRQS     96
/* only one GIC available */
#define ARM_GIC_MAX_NR      1

#endif